This platform has been marked as orphaned since September 2013, remove.
Signed-off-by: Tom Rini <trini@konsulko.com>
select SUPPORT_SPL
select PL011_SERIAL
-config TARGET_MX31ADS
- bool "Support mx31ads"
- select CPU_ARM1136
- select BOARD_EARLY_INIT_F
-
config TARGET_MX31PDK
bool "Support mx31pdk"
select BOARD_LATE_INIT
source "board/freescale/ls1012aqds/Kconfig"
source "board/freescale/ls1012ardb/Kconfig"
source "board/freescale/ls1012afrdm/Kconfig"
-source "board/freescale/mx31ads/Kconfig"
source "board/freescale/mx31pdk/Kconfig"
source "board/freescale/mx35pdk/Kconfig"
source "board/freescale/s32v234evb/Kconfig"
+++ /dev/null
-if TARGET_MX31ADS
-
-config SYS_BOARD
- default "mx31ads"
-
-config SYS_VENDOR
- default "freescale"
-
-config SYS_SOC
- default "mx31"
-
-config SYS_CONFIG_NAME
- default "mx31ads"
-
-endif
+++ /dev/null
-MX31ADS BOARD
-#M: (resigned) Guennadi Liakhovetski <g.liakhovetski@gmx.de>
-S: Orphan (since 2013-09)
-F: board/freescale/mx31ads/
-F: include/configs/mx31ads.h
-F: configs/mx31ads_defconfig
+++ /dev/null
-#
-# Copyright (C) 2008, Guennadi Liakhovetski <lg@denx.de>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := mx31ads.o
-obj-y += lowlevel_init.o
+++ /dev/null
-/*
- * Copyright (C) 2008, Guennadi Liakhovetski <lg@denx.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <asm/arch/imx-regs.h>
-
-.macro REG reg, val
- ldr r2, =\reg
- ldr r3, =\val
- str r3, [r2]
-.endm
-
-.macro REG8 reg, val
- ldr r2, =\reg
- ldr r3, =\val
- strb r3, [r2]
-.endm
-
-.macro DELAY loops
- ldr r2, =\loops
-1:
- subs r2, r2, #1
- nop
- bcs 1b
-.endm
-
-/* RedBoot: AIPS setup - Only setup MPROTx registers.
- * The PACR default values are good.*/
-.macro init_aips
- /*
- * Set all MPROTx to be non-bufferable, trusted for R/W,
- * not forced to user-mode.
- */
- ldr r0, =0x43F00000
- ldr r1, =0x77777777
- str r1, [r0, #0x00]
- str r1, [r0, #0x04]
- ldr r0, =0x53F00000
- str r1, [r0, #0x00]
- str r1, [r0, #0x04]
-
- /*
- * Clear the on and off peripheral modules Supervisor Protect bit
- * for SDMA to access them. Did not change the AIPS control registers
- * (offset 0x20) access type
- */
- ldr r0, =0x43F00000
- ldr r1, =0x0
- str r1, [r0, #0x40]
- str r1, [r0, #0x44]
- str r1, [r0, #0x48]
- str r1, [r0, #0x4C]
- ldr r1, [r0, #0x50]
- and r1, r1, #0x00FFFFFF
- str r1, [r0, #0x50]
-
- ldr r0, =0x53F00000
- ldr r1, =0x0
- str r1, [r0, #0x40]
- str r1, [r0, #0x44]
- str r1, [r0, #0x48]
- str r1, [r0, #0x4C]
- ldr r1, [r0, #0x50]
- and r1, r1, #0x00FFFFFF
- str r1, [r0, #0x50]
-.endm /* init_aips */
-
-/* RedBoot: MAX (Multi-Layer AHB Crossbar Switch) setup */
-.macro init_max
- ldr r0, =0x43F04000
- /* MPR - priority is M4 > M2 > M3 > M5 > M0 > M1 */
- ldr r1, =0x00302154
- str r1, [r0, #0x000] /* for S0 */
- str r1, [r0, #0x100] /* for S1 */
- str r1, [r0, #0x200] /* for S2 */
- str r1, [r0, #0x300] /* for S3 */
- str r1, [r0, #0x400] /* for S4 */
- /* SGPCR - always park on last master */
- ldr r1, =0x10
- str r1, [r0, #0x010] /* for S0 */
- str r1, [r0, #0x110] /* for S1 */
- str r1, [r0, #0x210] /* for S2 */
- str r1, [r0, #0x310] /* for S3 */
- str r1, [r0, #0x410] /* for S4 */
- /* MGPCR - restore default values */
- ldr r1, =0x0
- str r1, [r0, #0x800] /* for M0 */
- str r1, [r0, #0x900] /* for M1 */
- str r1, [r0, #0xA00] /* for M2 */
- str r1, [r0, #0xB00] /* for M3 */
- str r1, [r0, #0xC00] /* for M4 */
- str r1, [r0, #0xD00] /* for M5 */
-.endm /* init_max */
-
-/* RedBoot: M3IF setup */
-.macro init_m3if
- /* Configure M3IF registers */
- ldr r1, =0xB8003000
- /*
- * M3IF Control Register (M3IFCTL)
- * MRRP[0] = L2CC0 not on priority list (0 << 0) = 0x00000000
- * MRRP[1] = L2CC1 not on priority list (0 << 0) = 0x00000000
- * MRRP[2] = MBX not on priority list (0 << 0) = 0x00000000
- * MRRP[3] = MAX1 not on priority list (0 << 0) = 0x00000000
- * MRRP[4] = SDMA not on priority list (0 << 0) = 0x00000000
- * MRRP[5] = MPEG4 not on priority list (0 << 0) = 0x00000000
- * MRRP[6] = IPU1 on priority list (1 << 6) = 0x00000040
- * MRRP[7] = IPU2 not on priority list (0 << 0) = 0x00000000
- * ------------
- * 0x00000040
- */
- ldr r0, =0x00000040
- str r0, [r1] /* M3IF control reg */
-.endm /* init_m3if */
-
-/* RedBoot: To support 133MHz DDR */
-.macro init_drive_strength
- /*
- * Disable maximum drive strength SDRAM/DDR lines by clearing DSE1 bits
- * in SW_PAD_CTL registers
- */
-
- /* SDCLK */
- ldr r1, =0x43FAC200
- ldr r0, [r1, #0x6C]
- bic r0, r0, #(1 << 12)
- str r0, [r1, #0x6C]
-
- /* CAS */
- ldr r0, [r1, #0x70]
- bic r0, r0, #(1 << 22)
- str r0, [r1, #0x70]
-
- /* RAS */
- ldr r0, [r1, #0x74]
- bic r0, r0, #(1 << 2)
- str r0, [r1, #0x74]
-
- /* CS2 (CSD0) */
- ldr r0, [r1, #0x7C]
- bic r0, r0, #(1 << 22)
- str r0, [r1, #0x7C]
-
- /* DQM3 */
- ldr r0, [r1, #0x84]
- bic r0, r0, #(1 << 22)
- str r0, [r1, #0x84]
-
- /* DQM2, DQM1, DQM0, SD31-SD0, A25-A0, MA10 (0x288..0x2DC) */
- ldr r2, =22 /* (0x2E0 - 0x288) / 4 = 22 */
-pad_loop:
- ldr r0, [r1, #0x88]
- bic r0, r0, #(1 << 22)
- bic r0, r0, #(1 << 12)
- bic r0, r0, #(1 << 2)
- str r0, [r1, #0x88]
- add r1, r1, #4
- subs r2, r2, #0x1
- bne pad_loop
-.endm /* init_drive_strength */
-
-/* CPLD on CS4 setup */
-.macro init_cs4
- ldr r0, =WEIM_BASE
- ldr r1, =0x0000D843
- str r1, [r0, #0x40]
- ldr r1, =0x22252521
- str r1, [r0, #0x44]
- ldr r1, =0x22220A00
- str r1, [r0, #0x48]
-.endm /* init_cs4 */
-
-.globl lowlevel_init
-lowlevel_init:
-
- /* Redboot initializes very early AIPS, what for?
- * Then it also initializes Multi-Layer AHB Crossbar Switch,
- * M3IF */
- /* Also setup the Peripheral Port Remap register inside the core */
- ldr r0, =0x40000015 /* start from AIPS 2GB region */
- mcr p15, 0, r0, c15, c2, 4
-
- init_aips
-
- init_max
-
- init_m3if
-
- init_drive_strength
-
- init_cs4
-
- /* Image Processing Unit: */
- /* Too early to switch display on? */
- REG IPU_CONF, IPU_CONF_DI_EN /* Switch on Display Interface */
- /* Clock Control Module: */
- REG CCM_CCMR, 0x074B0BF5 /* Use CKIH, MCU PLL off */
-
- DELAY 0x40000
-
- REG CCM_CCMR, 0x074B0BF5 | CCMR_MPE /* MCU PLL on */
- REG CCM_CCMR, (0x074B0BF5 | CCMR_MPE) & ~CCMR_MDS /* Switch to MCU PLL */
-
- /* PBC CPLD on CS4 */
- mov r1, #CS4_BASE
- ldrh r1, [r1, #0x2]
- /* Is 27MHz switch set? */
- ands r1, r1, #0x10
-
- /* 532-133-66.5 */
- ldr r0, =CCM_BASE
- ldr r1, =0xFF871D58
- /* PDR0 */
- str r1, [r0, #0x4]
- ldreq r1, MPCTL_PARAM_532
- ldrne r1, MPCTL_PARAM_532_27
- /* MPCTL */
- str r1, [r0, #0x10]
-
- /* Set UPLL=240MHz, USB=60MHz */
- ldr r1, =0x49FCFE7F
- /* PDR1 */
- str r1, [r0, #0x8]
- ldreq r1, UPCTL_PARAM_240
- ldrne r1, UPCTL_PARAM_240_27
- /* UPCTL */
- str r1, [r0, #0x14]
- /* default CLKO to 1/8 of the ARM core */
- mov r1, #0x000002C0
- add r1, r1, #0x00000006
- /* COSR */
- str r1, [r0, #0x1c]
-
- /* RedBoot sets 0x3f, 7, 7, 3, 5, 1, 3, 0 */
-/* REG CCM_PDR0, PDR0_CSI_PODF(0x3f) | PDR0_CSI_PRDF(7) | PDR0_PER_PODF(7) | PDR0_HSP_PODF(2) | PDR0_NFC_PODF(6) | PDR0_IPG_PODF(1) | PDR0_MAX_PODF(2) | PDR0_MCU_PODF(0)*/
-
- /* Redboot: 0, 51, 10, 12 / 0, 14, 9, 13 */
-/* REG CCM_MPCTL, PLL_PD(0) | PLL_MFD(0x33) | PLL_MFI(7) | PLL_MFN(0x23)*/
- /* Default: 1, 4, 12, 1 */
- REG CCM_SPCTL, PLL_PD(1) | PLL_MFD(4) | PLL_MFI(12) | PLL_MFN(1)
-
- /* B8xxxxxx - NAND, 8xxxxxxx - CSD0 RAM */
- REG 0xB8001010, 0x00000004
- REG 0xB8001004, 0x006ac73a
- REG 0xB8001000, 0x92100000
- REG 0x80000f00, 0x12344321
- REG 0xB8001000, 0xa2100000
- REG 0x80000000, 0x12344321
- REG 0x80000000, 0x12344321
- REG 0xB8001000, 0xb2100000
- REG8 0x80000033, 0xda
- REG8 0x81000000, 0xff
- REG 0xB8001000, 0x82226080
- REG 0x80000000, 0xDEADBEEF
- REG 0xB8001010, 0x0000000c
-
- mov pc, lr
-
-MPCTL_PARAM_532:
- .word (((1-1) << 26) + ((52-1) << 16) + (10 << 10) + (12 << 0))
-MPCTL_PARAM_532_27:
- .word (((1-1) << 26) + ((15-1) << 16) + (9 << 10) + (13 << 0))
-UPCTL_PARAM_240:
- .word (((2-1) << 26) + ((13-1) << 16) + (9 << 10) + (3 << 0))
-UPCTL_PARAM_240_27:
- .word (((2-1) << 26) + ((9 -1) << 16) + (8 << 10) + (8 << 0))
+++ /dev/null
-/*
- * Copyright (C) 2008, Guennadi Liakhovetski <lg@denx.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-#include <asm/io.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/sys_proto.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int dram_init(void)
-{
- /* dram_init must store complete ramsize in gd->ram_size */
- gd->ram_size = get_ram_size((void *)PHYS_SDRAM_1,
- PHYS_SDRAM_1_SIZE);
- return 0;
-}
-
-int board_early_init_f(void)
-{
- int i;
-
- /* CS0: Nor Flash */
- /*
- * CS0L and CS0A values are from the RedBoot sources by Freescale
- * and are also equal to those used by Sascha Hauer for the Phytec
- * i.MX31 board. CS0U is just a slightly optimized hardware default:
- * the only non-zero field "Wait State Control" is set to half the
- * default value.
- */
- static const struct mxc_weimcs cs0 = {
- /* sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */
- CSCR_U(0, 0, 0, 0, 0, 0, 0, 0, 0, 15, 0, 0, 0),
- /* oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */
- CSCR_L(1, 0, 0, 0, 0, 1, 5, 0, 0, 0, 1, 1),
- /* ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/
- CSCR_A(0, 0, 7, 2, 0, 0, 2, 1, 0, 0, 0, 0, 0, 0)
- };
-
- mxc_setup_weimcs(0, &cs0);
-
- /* setup pins for UART1 */
- mx31_gpio_mux(MUX_RXD1__UART1_RXD_MUX);
- mx31_gpio_mux(MUX_TXD1__UART1_TXD_MUX);
- mx31_gpio_mux(MUX_RTS1__UART1_RTS_B);
- mx31_gpio_mux(MUX_CTS1__UART1_CTS_B);
-
- /* SPI2 */
- mx31_gpio_mux(MUX_CSPI2_SS2__CSPI2_SS2_B);
- mx31_gpio_mux(MUX_CSPI2_SCLK__CSPI2_CLK);
- mx31_gpio_mux(MUX_CSPI2_SPI_RDY__CSPI2_DATAREADY_B);
- mx31_gpio_mux(MUX_CSPI2_MOSI__CSPI2_MOSI);
- mx31_gpio_mux(MUX_CSPI2_MISO__CSPI2_MISO);
- mx31_gpio_mux(MUX_CSPI2_SS0__CSPI2_SS0_B);
- mx31_gpio_mux(MUX_CSPI2_SS1__CSPI2_SS1_B);
-
- /* start SPI2 clock */
- __REG(CCM_CGR2) = __REG(CCM_CGR2) | (3 << 4);
-
- /* PBC setup */
- /* Enable UART transceivers also reset the Ethernet/external UART */
- readw(CS4_BASE + 4);
-
- writew(0x8023, CS4_BASE + 4);
-
- /* RedBoot also has an empty loop with 100000 iterations here -
- * clock doesn't run yet */
- for (i = 0; i < 100000; i++)
- ;
-
- /* Clear the reset, toggle the LEDs */
- writew(0xDF, CS4_BASE + 6);
-
- /* clock still doesn't run */
- for (i = 0; i < 100000; i++)
- ;
-
- /* See 1.5.4 in IMX31ADSE_PERI_BUS_CNTRL_CPLD_RM.pdf */
- readb(CS4_BASE + 8);
- readb(CS4_BASE + 7);
- readb(CS4_BASE + 8);
- readb(CS4_BASE + 7);
-
- return 0;
-}
-
-int board_init(void)
-{
- gd->bd->bi_boot_params = 0x80000100; /* adress of boot parameters */
-
- return 0;
-}
-
-int checkboard(void)
-{
- printf("Board: MX31ADS\n");
- return 0;
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_CS8900
- rc = cs8900_initialize(0, CONFIG_CS8900_BASE);
-#endif
- return rc;
-}
-#endif
+++ /dev/null
-/*
- * January 2004 - Changed to support H4 device
- * Copyright (c) 2004 Texas Instruments
- *
- * (C) Copyright 2002
- * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
-OUTPUT_ARCH(arm)
-ENTRY(_start)
-SECTIONS
-{
- . = 0x00000000;
-
- . = ALIGN(4);
- .text :
- {
- *(.__image_copy_start)
- /* WARNING - the following is hand-optimized to fit within */
- /* the sector layout of our flash chips! XXX FIXME XXX */
-
- * (.vectors)
- arch/arm/cpu/arm1136/start.o (.text*)
- board/freescale/mx31ads/built-in.o (.text*)
- arch/arm/lib/built-in.o (.text*)
- net/built-in.o (.text*)
- drivers/mtd/built-in.o (.text*)
-
- . = DEFINED(env_offset) ? env_offset : .;
- env/embedded.o(.text*)
-
- *(.text*)
- }
- . = ALIGN(4);
- .rodata : { *(.rodata*) }
-
- . = ALIGN(4);
- .data : {
- *(.data*)
- }
-
- . = ALIGN(4);
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
- . = ALIGN(4);
-
- .image_copy_end :
- {
- *(.__image_copy_end)
- }
-
- .rel_dyn_start :
- {
- *(.__rel_dyn_start)
- }
-
- .rel.dyn : {
- *(.rel*)
- }
-
- .rel_dyn_end :
- {
- *(.__rel_dyn_end)
- }
-
- .hash : { *(.hash*) }
-
- .end :
- {
- *(.__end)
- }
-
- _image_binary_end = .;
-
-/*
- * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c
- * __bss_base and __bss_limit are for linker only (overlay ordering)
- */
-
- .bss_start __rel_dyn_start (OVERLAY) : {
- KEEP(*(.__bss_start));
- __bss_base = .;
- }
-
- .bss __bss_base (OVERLAY) : {
- *(.bss*)
- . = ALIGN(4);
- __bss_limit = .;
- }
- .bss_end __bss_limit (OVERLAY) : {
- KEEP(*(.__bss_end));
- }
-
- .dynsym _image_binary_end : { *(.dynsym) }
- .dynbss : { *(.dynbss) }
- .dynstr : { *(.dynstr*) }
- .dynamic : { *(.dynamic*) }
- .gnu.hash : { *(.gnu.hash) }
- .plt : { *(.plt*) }
- .interp : { *(.interp*) }
- .gnu : { *(.gnu*) }
- .ARM.exidx : { *(.ARM.exidx*) }
-}
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_TARGET_MX31ADS=y
-CONFIG_SYS_TEXT_BASE=0xA0000000
-# CONFIG_AUTO_COMPLETE is not set
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_SPI=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
-CONFIG_ENV_IS_IN_FLASH=y
-CONFIG_MXC_GPIO=y
-# CONFIG_MMC is not set
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_MXC_SPI=y
+++ /dev/null
-/*
- * Copyright (C) 2008, Guennadi Liakhovetski <lg@denx.de>
- *
- * Configuration settings for the MX31ADS Freescale board.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <asm/arch/imx-regs.h>
-
- /* High Level Configuration Options */
-#define CONFIG_MX31 1 /* This is a mx31 */
-
-#define CONFIG_MACH_TYPE MACH_TYPE_MX31ADS
-
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024)
-
-/*
- * Hardware drivers
- */
-
-#define CONFIG_MXC_UART
-#define CONFIG_MXC_UART_BASE UART1_BASE
-
-#define CONFIG_HARD_SPI 1
-#define CONFIG_DEFAULT_SPI_BUS 1
-#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH)
-
-/* PMIC Controller */
-#define CONFIG_POWER
-#define CONFIG_POWER_SPI
-#define CONFIG_POWER_FSL
-#define CONFIG_FSL_PMIC_BUS 1
-#define CONFIG_FSL_PMIC_CS 0
-#define CONFIG_FSL_PMIC_CLK 1000000
-#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH)
-#define CONFIG_FSL_PMIC_BITLEN 32
-#define CONFIG_RTC_MC13XXX
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_CONS_INDEX 1
-
-#define CONFIG_LOADADDR 0x80800000 /* loadaddr env var */
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "uboot_addr=0xa0000000\0" \
- "uboot=mx31ads/u-boot.bin\0" \
- "kernel=mx31ads/uImage\0" \
- "nfsroot=/opt/eldk/arm\0" \
- "bootargs_base=setenv bootargs console=ttymxc0,115200\0" \
- "bootargs_nfs=setenv bootargs ${bootargs} root=/dev/nfs " \
- "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
- "bootcmd=run bootcmd_net\0" \
- "bootcmd_net=run bootargs_base bootargs_nfs; " \
- "tftpboot ${loadaddr} ${kernel}; bootm\0" \
- "prg_uboot=tftpboot ${loadaddr} ${uboot}; " \
- "protect off ${uboot_addr} 0xa003ffff; " \
- "erase ${uboot_addr} 0xa003ffff; " \
- "cp.b ${loadaddr} ${uboot_addr} ${filesize}; " \
- "setenv filesize; saveenv\0"
-
-#define CONFIG_CS8900
-#define CONFIG_CS8900_BASE 0xb4020300
-#define CONFIG_CS8900_BUS16 1 /* follow the Linux driver */
-
-/*
- * The MX31ADS board seems to have a hardware "peculiarity" confirmed under
- * U-Boot, RedBoot and Linux: the ethernet Rx signal is reaching the CS8900A
- * controller inverted. The controller is capable of detecting and correcting
- * this, but it needs 4 network packets for that. Which means, at startup, you
- * will not receive answers to the first 4 packest, unless there have been some
- * broadcasts on the network, or your board is on a hub. Reducing the ARP
- * timeout from default 5 seconds to 200ms we speed up the initial TFTP
- * transfer, should the user wish one, significantly.
- */
-#define CONFIG_ARP_TIMEOUT 200UL
-
-/*
- * Miscellaneous configurable options
- */
-
-#define CONFIG_SYS_MEMTEST_START 0 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x10000
-
-#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM_1 CSD0_BASE
-#define PHYS_SDRAM_1_SIZE (128 * 1024 * 1024)
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_GBL_DATA_OFFSET)
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-#define CONFIG_SYS_FLASH_BASE CS0_BASE
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 262 /* max number of sectors on one chip */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /* Monitor at beginning of flash */
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256KiB */
-
-#define CONFIG_ENV_SECT_SIZE (128 * 1024)
-#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
-
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
- */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash memory is CFI compliant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */
-#define CONFIG_FLASH_SPANSION_S29WS_N 1 /* A non-standard buffered write algorithm */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */
-#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use hardware sector protection */
-
-/*
- * JFFS2 partitions
- */
-#define CONFIG_JFFS2_DEV "nor0"
-
-#endif /* __CONFIG_H */
projects / u-boot / commitdiff