Armada100: Enable 88E3015 PHY support for GplugD

This patch adds support for 88E3015 PHY for Marvell GplugD board.
This patch depends on series of patch which adds support for Marvell
GuruPlug-Display.

Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>

diff --git a/board/Marvell/gplugd/gplugd.c b/board/Marvell/gplugd/gplugd.c
index 8560b3f109c39ec452b9069475483307cd4869a3..b4f7f81583ece4586e840b4b130ac73841bbe08b 100644 (file)
--- a/board/Marvell/gplugd/gplugd.c
+++ b/board/Marvell/gplugd/gplugd.c
@@ -32,6 +32,8 @@
 #include <mvmfp.h>
 #include <asm/arch/mfp.h>
 #include <asm/arch/armada100.h>
+#include <asm/gpio.h>
+#include <miiphy.h>
 
 #ifdef CONFIG_ARMADA100_FEC
 #include <net.h>
@@ -83,6 +85,11 @@ int board_init(void)
        gd->bd->bi_arch_number = MACH_TYPE_SHEEVAD;
        /* adress of boot parameters */
        gd->bd->bi_boot_params = armd1_sdram_base(0) + 0x100;
+       /* Assert PHY_RST# */
+       gpio_direction_output(CONFIG_SYS_GPIO_PHY_RST, GPIO_LOW);
+       udelay(10);
+       /* Deassert PHY_RST# */
+       gpio_set_value(CONFIG_SYS_GPIO_PHY_RST, GPIO_HIGH);
        return 0;
 }
 
@@ -97,4 +104,30 @@ int board_eth_init(bd_t *bis)
 
        return armada100_fec_register(ARMD1_FEC_BASE);
 }
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and initialize PHY chip 88E3015 */
+void reset_phy(void)
+{
+       u16 phy_adr;
+       const char *name = "armd-fec0";
+
+       if (miiphy_set_current_dev(name))
+               return;
+
+       /* command to read PHY dev address */
+       if (miiphy_read(name, 0xff, 0xff, &phy_adr)) {
+               printf("Err..%s could not read PHY dev address\n", __func__);
+               return;
+       }
+
+       /* Set Ethernet LED in TX blink mode */
+       miiphy_write(name, phy_adr, PHY_LED_MAN_REG, 0x00);
+       miiphy_write(name, phy_adr, PHY_LED_PAR_SEL_REG, PHY_LED_VAL);
+
+       /* reset the phy */
+       miiphy_reset(name, phy_adr);
+       debug("88E3015 Initialized on %s\n", name);
+}
+#endif /* CONFIG_RESET_PHY_R */
 #endif /* CONFIG_ARMADA100_FEC */

diff --git a/include/configs/gplugd.h b/include/configs/gplugd.h
index 3ad2de5adbe2aff24cf0d2ea88e0cad52e2c0eda..5f72163473f074f3f7b8ec5e89ef493dbcf822f8 100644 (file)
--- a/include/configs/gplugd.h
+++ b/include/configs/gplugd.h
@@ -77,6 +77,20 @@
 #define CONFIG_BOOTP_DHCP_REQUEST_DELAY                50000
 #endif /* CONFIG_CMD_NET */
 
+/* GPIO Support */
+#define CONFIG_MARVELL_GPIO
+
+/* PHY configuration */
+#define CONFIG_MII
+#define CONFIG_CMD_MII
+#define CONFIG_RESET_PHY_R
+/* 88E3015 register definition */
+#define PHY_LED_PAR_SEL_REG            22
+#define PHY_LED_MAN_REG                        25
+#define PHY_LED_VAL                    0x5b    /* LINK LED1, ACT LED2 */
+/* GPIO Configuration for PHY */
+#define CONFIG_SYS_GPIO_PHY_RST                104     /* GPIO104 */
+
 /*
  * mv-common.h should be defined after CMD configs since it used them
  * to enable certain macros