eeprom: Shuffle code around

Just move the code around so that the forward declarations are not
necessary. Also zap a few checkpatch issues where applicable and
zap the use of #ifdef CONFIG_CMD_EEPROM in the code, since this is
always true.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>

diff --git a/common/cmd_eeprom.c b/common/cmd_eeprom.c
index e9904cd6982bad704260e4a5c247ddb8342a3a65..4335079d5651bdd1d7e3b5a4ab0b28b31a7c9754 100644 (file)
--- a/common/cmd_eeprom.c
+++ b/common/cmd_eeprom.c
@@ -25,94 +25,55 @@
 #include <command.h>
 #include <i2c.h>
 
-extern void eeprom_init  (void);
-extern int  eeprom_read  (unsigned dev_addr, unsigned offset,
-                         uchar *buffer, unsigned cnt);
-extern int  eeprom_write (unsigned dev_addr, unsigned offset,
-                         uchar *buffer, unsigned cnt);
-#if defined(CONFIG_SYS_EEPROM_WREN)
-extern int eeprom_write_enable (unsigned dev_addr, int state);
+#ifndef        CONFIG_SYS_I2C_SPEED
+#define        CONFIG_SYS_I2C_SPEED    50000
 #endif
 
-
+/* Maximum number of times to poll for acknowledge after write */
 #if defined(CONFIG_SYS_EEPROM_X40430)
-       /* Maximum number of times to poll for acknowledge after write */
 #define MAX_ACKNOWLEDGE_POLLS  10
 #endif
 
-/* ------------------------------------------------------------------------- */
-
-#if defined(CONFIG_CMD_EEPROM)
-static int do_eeprom(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
-       const char *const fmt =
-               "\nEEPROM @0x%lX %s: addr %08lx  off %04lx  count %ld ... ";
-
-#if defined(CONFIG_SYS_I2C_MULTI_EEPROMS)
-       if (argc == 6) {
-               ulong dev_addr = simple_strtoul (argv[2], NULL, 16);
-               ulong addr = simple_strtoul (argv[3], NULL, 16);
-               ulong off  = simple_strtoul (argv[4], NULL, 16);
-               ulong cnt  = simple_strtoul (argv[5], NULL, 16);
-#else
-       if (argc == 5) {
-               ulong dev_addr = CONFIG_SYS_DEF_EEPROM_ADDR;
-               ulong addr = simple_strtoul (argv[2], NULL, 16);
-               ulong off  = simple_strtoul (argv[3], NULL, 16);
-               ulong cnt  = simple_strtoul (argv[4], NULL, 16);
-#endif /* CONFIG_SYS_I2C_MULTI_EEPROMS */
-
-# if !defined(CONFIG_SPI) || defined(CONFIG_ENV_EEPROM_IS_ON_I2C)
-               eeprom_init ();
-# endif /* !CONFIG_SPI */
-
-               if (strcmp (argv[1], "read") == 0) {
-                       int rcode;
-
-                       printf (fmt, dev_addr, argv[1], addr, off, cnt);
-
-                       rcode = eeprom_read (dev_addr, off, (uchar *) addr, cnt);
-
-                       puts ("done\n");
-                       return rcode;
-               } else if (strcmp (argv[1], "write") == 0) {
-                       int rcode;
-
-                       printf (fmt, dev_addr, argv[1], addr, off, cnt);
-
-                       rcode = eeprom_write (dev_addr, off, (uchar *) addr, cnt);
-
-                       puts ("done\n");
-                       return rcode;
-               }
-       }
-
-       return CMD_RET_USAGE;
-}
-#endif
-
-/*-----------------------------------------------------------------------
- *
+/*
  * for CONFIG_SYS_I2C_EEPROM_ADDR_LEN == 2 (16-bit EEPROM address) offset is
  *   0x000nxxxx for EEPROM address selectors at n, offset xxxx in EEPROM.
  *
  * for CONFIG_SYS_I2C_EEPROM_ADDR_LEN == 1 (8-bit EEPROM page address) offset is
  *   0x00000nxx for EEPROM address selectors and page number at n.
  */
-
 #if !defined(CONFIG_SPI) || defined(CONFIG_ENV_EEPROM_IS_ON_I2C)
-#if !defined(CONFIG_SYS_I2C_EEPROM_ADDR_LEN) || CONFIG_SYS_I2C_EEPROM_ADDR_LEN < 1 || CONFIG_SYS_I2C_EEPROM_ADDR_LEN > 2
+#if !defined(CONFIG_SYS_I2C_EEPROM_ADDR_LEN) || \
+    (CONFIG_SYS_I2C_EEPROM_ADDR_LEN < 1) || \
+    (CONFIG_SYS_I2C_EEPROM_ADDR_LEN > 2)
 #error CONFIG_SYS_I2C_EEPROM_ADDR_LEN must be 1 or 2
 #endif
 #endif
 
+#if defined(CONFIG_SYS_EEPROM_WREN)
+extern int eeprom_write_enable (unsigned dev_addr, int state);
+#endif
+
+void eeprom_init(void)
+{
+       /* SPI EEPROM */
+#if defined(CONFIG_SPI) && !defined(CONFIG_ENV_EEPROM_IS_ON_I2C)
+       spi_init_f ();
+#endif
+
+       /* I2C EEPROM */
+#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT)
+       i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+#endif
+}
+
 int eeprom_read (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt)
 {
        unsigned end = offset + cnt;
        unsigned blk_off;
        int rcode = 0;
 
-       /* Read data until done or would cross a page boundary.
+       /*
+        * Read data until done or would cross a page boundary.
         * We must write the address again when changing pages
         * because the next page may be in a different device.
         */
@@ -174,15 +135,6 @@ int eeprom_read (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt
        return rcode;
 }
 
-/*-----------------------------------------------------------------------
- *
- * for CONFIG_SYS_I2C_EEPROM_ADDR_LEN == 2 (16-bit EEPROM address) offset is
- *   0x000nxxxx for EEPROM address selectors at n, offset xxxx in EEPROM.
- *
- * for CONFIG_SYS_I2C_EEPROM_ADDR_LEN == 1 (8-bit EEPROM page address) offset is
- *   0x00000nxx for EEPROM address selectors and page number at n.
- */
-
 int eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt)
 {
        unsigned end = offset + cnt;
@@ -200,7 +152,8 @@ int eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cn
 #if defined(CONFIG_SYS_EEPROM_WREN)
        eeprom_write_enable (dev_addr,1);
 #endif
-       /* Write data until done or would cross a write page boundary.
+       /*
+        * Write data until done or would cross a write page boundary.
         * We must write the address again when changing pages
         * because the address counter only increments within a page.
         */
@@ -363,8 +316,7 @@ int eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cn
 }
 
 #if !defined(CONFIG_SPI) || defined(CONFIG_ENV_EEPROM_IS_ON_I2C)
-int
-eeprom_probe (unsigned dev_addr, unsigned offset)
+int eeprom_probe(unsigned dev_addr, unsigned offset)
 {
        unsigned char chip;
 
@@ -382,30 +334,52 @@ eeprom_probe (unsigned dev_addr, unsigned offset)
 }
 #endif
 
-/*-----------------------------------------------------------------------
- * Set default values
- */
-#ifndef        CONFIG_SYS_I2C_SPEED
-#define        CONFIG_SYS_I2C_SPEED    50000
-#endif
-
-void eeprom_init  (void)
+static int do_eeprom(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 {
+       const char *const fmt =
+               "\nEEPROM @0x%lX %s: addr %08lx  off %04lx  count %ld ... ";
 
-#if defined(CONFIG_SPI) && !defined(CONFIG_ENV_EEPROM_IS_ON_I2C)
-       spi_init_f ();
-#endif
-#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SYS_I2C_SOFT)
-       i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-#endif
-}
+#if defined(CONFIG_SYS_I2C_MULTI_EEPROMS)
+       if (argc == 6) {
+               ulong dev_addr = simple_strtoul (argv[2], NULL, 16);
+               ulong addr = simple_strtoul (argv[3], NULL, 16);
+               ulong off  = simple_strtoul (argv[4], NULL, 16);
+               ulong cnt  = simple_strtoul (argv[5], NULL, 16);
+#else
+       if (argc == 5) {
+               ulong dev_addr = CONFIG_SYS_DEF_EEPROM_ADDR;
+               ulong addr = simple_strtoul (argv[2], NULL, 16);
+               ulong off  = simple_strtoul (argv[3], NULL, 16);
+               ulong cnt  = simple_strtoul (argv[4], NULL, 16);
+#endif /* CONFIG_SYS_I2C_MULTI_EEPROMS */
 
-/*-----------------------------------------------------------------------
- */
+# if !defined(CONFIG_SPI) || defined(CONFIG_ENV_EEPROM_IS_ON_I2C)
+               eeprom_init ();
+# endif /* !CONFIG_SPI */
 
-/***************************************************/
+               if (strcmp (argv[1], "read") == 0) {
+                       int rcode;
+
+                       printf (fmt, dev_addr, argv[1], addr, off, cnt);
 
-#if defined(CONFIG_CMD_EEPROM)
+                       rcode = eeprom_read (dev_addr, off, (uchar *) addr, cnt);
+
+                       puts ("done\n");
+                       return rcode;
+               } else if (strcmp (argv[1], "write") == 0) {
+                       int rcode;
+
+                       printf (fmt, dev_addr, argv[1], addr, off, cnt);
+
+                       rcode = eeprom_write (dev_addr, off, (uchar *) addr, cnt);
+
+                       puts ("done\n");
+                       return rcode;
+               }
+       }
+
+       return CMD_RET_USAGE;
+}
 
 #ifdef CONFIG_SYS_I2C_MULTI_EEPROMS
 U_BOOT_CMD(
@@ -424,5 +398,3 @@ U_BOOT_CMD(
        "       - read/write `cnt' bytes at EEPROM offset `off'"
 )
 #endif /* CONFIG_SYS_I2C_MULTI_EEPROMS */
-
-#endif