#include <net.h> /* for eth_init() */
#include <rtc.h>
#include "sixnet.h"
+#ifdef CONFIG_SHOW_BOOT_PROGRESS
+# include <status_led.h>
+#endif
#define ORMASK(size) ((-size) & OR_AM_MSK)
/* ------------------------------------------------------------------------- */
+#ifdef CONFIG_SHOW_BOOT_PROGRESS
+void show_boot_progress (int status)
+{
+#if defined(CONFIG_STATUS_LED)
+# if defined(STATUS_LED_BOOT)
+ if (status == 15) {
+ /* ready to transfer to kernel, make sure LED is proper state */
+ status_led_set(STATUS_LED_BOOT, CONFIG_BOOT_LED_STATE);
+ }
+# endif /* STATUS_LED_BOOT */
+#endif /* CONFIG_STATUS_LED */
+}
+#endif
+
+/* ------------------------------------------------------------------------- */
+
/*
* Check Board Identity:
* returns 0 if recognized, -1 if unknown
volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile memctl8xx_t *memctl = &immap->im_memctl;
+ char* s;
+ char* e;
+ int reg;
bd_t *bd = gd->bd;
memctl->memc_or2 = NVRAM_OR_PRELIM;
immap->im_sit.sit_rtc = tim;
}
-#if 0
- /* The code below is no longer valid since the prototype of
- * eth_init() and eth_halt() have been changed to support
- * multi-ethernet feature in U-Boot; the eth_initialize()
- * routine should be called before any access to the ethernet
- * callbacks.
+ /* set up ethernet address for SCC ethernet. If eth1addr
+ * is present it gets a unique address, otherwise it
+ * shares the FEC address.
*/
+ s = getenv("eth1addr");
+ if (s == NULL)
+ s = getenv("ethaddr");
+ for (reg=0; reg<6; ++reg) {
+ bd->bi_enet1addr[reg] = s ? simple_strtoul(s, &e, 16) : 0;
+ if (s)
+ s = (*e) ? e+1 : e;
+ }
- /* FIXME - for now init ethernet to force PHY special mode */
- eth_init(bd);
- eth_halt();
-#endif
return (0);
}
*
* The memory size MUST be a power of 2 for this to work.
*
- * The only memory modified is 4 bytes at offset 0. This is important
+ * The only memory modified is 8 bytes at offset 0. This is important
* since for the SRAM this location is reserved for autosizing, so if
* it is modified and the board is reset before ram_size() completes
* no damage is done. Normally even the memory at 0 is preserved. The
{
volatile long *test_addr;
volatile long *base_addr = base;
- volatile long *flash = (volatile long*)CFG_FLASH_BASE;
ulong ofs; /* byte offset from base_addr */
ulong save; /* to make test non-destructive */
- ulong junk;
+ ulong save2; /* to make test non-destructive */
long ramsize = -1; /* size not determined yet */
save = *base_addr; /* save value at 0 so can restore */
+ save2 = *(base_addr+1); /* save value at 4 so can restore */
/* is any SRAM present? */
*base_addr = 0x5555aaaa;
- /* use flash read to modify data bus, since with no SRAM present
- * the data bus may retain the value if our code is running
- * completely in the cache.
+ /* It is important to drive the data bus with different data so
+ * it doesn't remember the value and look like RAM that isn't there.
*/
- junk = *flash;
+ *(base_addr + 1) = 0xaaaa5555; /* use write to modify data bus */
if (*base_addr != 0x5555aaaa)
ramsize = 0; /* no RAM present, or defective */
else {
*base_addr = 0xaaaa5555;
- junk = *flash; /* use flash read to modify data bus */
+ *(base_addr + 1) = 0x5555aaaa; /* use write to modify data bus */
if (*base_addr != 0xaaaa5555)
ramsize = 0; /* no RAM present, or defective */
}
}
*base_addr = save; /* restore value at 0 */
+ *(base_addr+1) = save2; /* restore value at 4 */
return (ramsize);
}
MCR_MLCF(2) | MCR_MAD(0x30)) /* twice at 0x30 */
/* MAMR values work in either mamr or mbmr */
-/* 8 column SDRAM */
-#define SDRAM_MAMR_8COL /* refresh at 50MHz */ \
+#define SDRAM_MAMR_BASE /* refresh at 50MHz */ \
((195 << MAMR_PTA_SHIFT) | MAMR_PTAE \
- | MAMR_AMA_TYPE_0 /* Address MUX 0 */ \
| MAMR_DSA_1_CYCL /* 1 cycle disable */ \
- | MAMR_G0CLA_A11 /* GPL0 A11[MPC] */ \
| MAMR_RLFA_1X /* Read loop 1 time */ \
| MAMR_WLFA_1X /* Write loop 1 time */ \
| MAMR_TLFA_4X) /* Timer loop 4 times */
+/* 8 column SDRAM */
+#define SDRAM_MAMR_8COL (SDRAM_MAMR_BASE \
+ | MAMR_AMA_TYPE_0 /* Address MUX 0 */ \
+ | MAMR_G0CLA_A11) /* GPL0 A11[MPC] */
/* 9 column SDRAM */
-#define SDRAM_MAMR_9COL ((SDRAM_MAMR_8COL & (~MAMR_G0CLA_A11)) | MAMR_G0CLA_A10)
+#define SDRAM_MAMR_9COL (SDRAM_MAMR_BASE \
+ | MAMR_AMA_TYPE_1 /* Address MUX 1 */ \
+ | MAMR_G0CLA_A10) /* GPL0 A10[MPC] */
/* base address 0, 32-bit port, SDRAM UPM, valid */
#define SDRAM_BR_VALUE (BR_PS_32 | BR_MS_UPMA | BR_V)
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#endif
+/*-----------------------------------------------------------------------
+ * Definitions for status LED
+ */
+#define CONFIG_STATUS_LED 1 /* Status LED enabled */
+
+# define STATUS_LED_PAR im_ioport.iop_papar
+# define STATUS_LED_DIR im_ioport.iop_padir
+# define STATUS_LED_ODR im_ioport.iop_paodr
+# define STATUS_LED_DAT im_ioport.iop_padat
+
+# define STATUS_LED_BIT 0x8000 /* LED 0 is on PA.0 */
+# define STATUS_LED_PERIOD ((CFG_HZ / 2) / 5) /* blink at 5 Hz */
+# define STATUS_LED_STATE STATUS_LED_BLINKING
+
+# define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */
+
+# define STATUS_LED_BOOT 0 /* LED 0 used for boot status */
+
+#ifdef DEV /* development (debug) settings */
+#define CONFIG_BOOT_LED_STATE STATUS_LED_OFF
+#else /* production settings */
+#define CONFIG_BOOT_LED_STATE STATUS_LED_ON
+#endif
+
+#define CONFIG_SHOW_BOOT_PROGRESS 1
+
#define CONFIG_BOOTCOMMAND "bootm f8040000 f8100000" /* autoboot command */
#define CONFIG_BOOTARGS "root=/dev/ram ip=off"
#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND \
- "bootp; " \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \
- "bootm"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$(serverip):$(rootpath)\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs $(bootargs) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
+ ":$(hostname):$(netdev):off panic=1\0" \
+ "flash_nfs=run nfsargs addip;" \
+ "bootm $(kernel_addr)\0" \
+ "flash_self=run ramargs addip;" \
+ "bootm $(kernel_addr) $(ramdisk_addr)\0" \
+ "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \
+ "rootpath=/opt/eldk/ppc_82xx\0" \
+ "bootfile=/tftpboot/TQM8260/uImage\0" \
+ "kernel_addr=40040000\0" \
+ "ramdisk_addr=40100000\0" \
+ ""
+#define CONFIG_BOOTCOMMAND "run flash_self"
/* enable I2C and select the hardware/software driver */
#undef CONFIG_HARD_I2C /* I2C with hardware support */
projects / u-boot / commitdiff