sunxi: clock: Set AHB1 clock frequency to 200MHz on Allwinner H3

The 3.4 kernel from the Allwinner SDK is clocking AHB1 at 200MHz
on Allwinner H3 and using PLL6 as the clock source (PLL6/3).
This can be verified by reading the value of the AHB1_APB1_CFG_REG
register via /dev/mem. It always reads as 0x3180 regardless of
the current cpufreq operating point. So this configuration should
be safe for use in U-Boot too.

PLL6 also needs to be configured before it is used as the clock
source, according to the "CCU / Programming Guidelines" section
of the Allwinner manual.

The current low AHB1 clock speed is limiting the USB transfer
speed when booting via FEL. This patch can increase the FEL USB
transfer speed from ~510 KB/s to ~950 KB/s.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

diff --git a/arch/arm/cpu/armv7/sunxi/clock_sun6i.c b/arch/arm/cpu/armv7/sunxi/clock_sun6i.c
index 3ab3b31867807ced4d593bffdb7021211e9e7bf5..916ee48e4bb190241a83b5988af9670e8b31e460 100644 (file)
--- a/arch/arm/cpu/armv7/sunxi/clock_sun6i.c
+++ b/arch/arm/cpu/armv7/sunxi/clock_sun6i.c
@@ -34,9 +34,11 @@ void clock_init_safe(void)
 
        clock_set_pll1(408000000);
 
-       writel(AHB1_ABP1_DIV_DEFAULT, &ccm->ahb1_apb1_div);
-
        writel(PLL6_CFG_DEFAULT, &ccm->pll6_cfg);
+       while (!(readl(&ccm->pll6_cfg) & CCM_PLL6_CTRL_LOCK))
+               ;
+
+       writel(AHB1_ABP1_DIV_DEFAULT, &ccm->ahb1_apb1_div);
 
        writel(MBUS_CLK_DEFAULT, &ccm->mbus0_clk_cfg);
        writel(MBUS_CLK_DEFAULT, &ccm->mbus1_clk_cfg);

diff --git a/arch/arm/include/asm/arch-sunxi/clock_sun6i.h b/arch/arm/include/asm/arch-sunxi/clock_sun6i.h
index 584d351cb40ddb4ebcbe0ab56e45014ed8f65230..09337a1deaf9b4670c8f0f7406c5a350f5423c13 100644 (file)
--- a/arch/arm/include/asm/arch-sunxi/clock_sun6i.h
+++ b/arch/arm/include/asm/arch-sunxi/clock_sun6i.h
@@ -201,6 +201,7 @@ struct sunxi_ccm_reg {
 #define CCM_PLL6_CTRL_N_MASK           (0x1f << CCM_PLL6_CTRL_N_SHIFT)
 #define CCM_PLL6_CTRL_K_SHIFT          4
 #define CCM_PLL6_CTRL_K_MASK           (0x3 << CCM_PLL6_CTRL_K_SHIFT)
+#define CCM_PLL6_CTRL_LOCK             (1 << 28)
 
 #define CCM_MIPI_PLL_CTRL_M_SHIFT      0
 #define CCM_MIPI_PLL_CTRL_M_MASK       (0xf << CCM_MIPI_PLL_CTRL_M_SHIFT)
@@ -219,7 +220,11 @@ struct sunxi_ccm_reg {
 #define CCM_PLL11_CTRL_UPD             (0x1 << 30)
 #define CCM_PLL11_CTRL_EN              (0x1 << 31)
 
-#define AHB1_ABP1_DIV_DEFAULT          0x00002020
+#if defined CONFIG_MACH_SUN8I_H3
+#define AHB1_ABP1_DIV_DEFAULT          0x00003180 /* AHB1=PLL6/3,APB1=AHB1/2 */
+#else
+#define AHB1_ABP1_DIV_DEFAULT          0x00002020 /* AHB1=AXI/4, APB1=AHB1/2 */
+#endif
 
 #define AXI_GATE_OFFSET_DRAM           0