uint16_t lvl;
};
+#define GPIO_USESEL_OFFSET(x) (x)
+#define GPIO_IOSEL_OFFSET(x) (x + 4)
+#define GPIO_LVL_OFFSET(x) (x + 8)
+
+#define IOPAD_MODE_MASK 0x7
+#define IOPAD_PULL_ASSIGN_SHIFT 7
+#define IOPAD_PULL_ASSIGN_MASK (0x3 << IOPAD_PULL_ASSIGN_SHIFT)
+#define IOPAD_PULL_STRENGTH_SHIFT 9
+#define IOPAD_PULL_STRENGTH_MASK (0x3 << IOPAD_PULL_STRENGTH_SHIFT)
+
/* TODO: Move this to device tree, or platform data */
void ich_gpio_set_gpio_map(const struct pch_gpio_map *map)
{
gd->arch.gpio_map = map;
}
-static int gpio_ich6_ofdata_to_platdata(struct udevice *dev)
+static int gpio_ich6_get_base(unsigned long base)
{
- struct ich6_bank_platdata *plat = dev_get_platdata(dev);
pci_dev_t pci_dev; /* handle for 0:1f:0 */
u8 tmpbyte;
u16 tmpword;
u32 tmplong;
- u16 gpiobase;
- int offset;
/* Where should it be? */
pci_dev = PCI_BDF(0, 0x1f, 0);
* while on the Ivybridge the bit0 is used to indicate it is an
* I/O space.
*/
- tmplong = x86_pci_read_config32(pci_dev, PCI_CFG_GPIOBASE);
+ tmplong = x86_pci_read_config32(pci_dev, base);
if (tmplong == 0x00000000 || tmplong == 0xffffffff) {
- debug("%s: unexpected GPIOBASE value\n", __func__);
+ debug("%s: unexpected BASE value\n", __func__);
return -ENODEV;
}
* at the offset that we just read. Bit 0 indicates that it's
* an I/O address, not a memory address, so mask that off.
*/
- gpiobase = tmplong & 0xfffe;
+ return tmplong & 0xfffc;
+}
+
+static int _ich6_gpio_set_value(uint16_t base, unsigned offset, int value)
+{
+ u32 val;
+
+ val = inl(base);
+ if (value)
+ val |= (1UL << offset);
+ else
+ val &= ~(1UL << offset);
+ outl(val, base);
+
+ return 0;
+}
+
+static int _ich6_gpio_set_function(uint16_t base, unsigned offset, int func)
+{
+ u32 val;
+
+ if (func) {
+ val = inl(base);
+ val |= (1UL << offset);
+ outl(val, base);
+ } else {
+ val = inl(base);
+ val &= ~(1UL << offset);
+ outl(val, base);
+ }
+
+ return 0;
+}
+
+static int _ich6_gpio_set_direction(uint16_t base, unsigned offset, int dir)
+{
+ u32 val;
+
+ if (!dir) {
+ val = inl(base);
+ val |= (1UL << offset);
+ outl(val, base);
+ } else {
+ val = inl(base);
+ val &= ~(1UL << offset);
+ outl(val, base);
+ }
+
+ return 0;
+}
+
+static int _gpio_ich6_pinctrl_cfg_pin(s32 gpiobase, s32 iobase, int pin_node)
+{
+ u32 gpio_offset[2];
+ int pad_offset;
+ int val;
+ int ret;
+ const void *prop;
+
+ /*
+ * GPIO node is not mandatory, so we only do the
+ * pinmuxing if the node exist.
+ */
+ ret = fdtdec_get_int_array(gd->fdt_blob, pin_node, "gpio-offset",
+ gpio_offset, 2);
+ if (!ret) {
+ /* Do we want to force the GPIO mode? */
+ prop = fdt_getprop(gd->fdt_blob, pin_node, "mode-gpio",
+ NULL);
+ if (prop)
+ _ich6_gpio_set_function(GPIO_USESEL_OFFSET
+ (gpiobase) +
+ gpio_offset[0],
+ gpio_offset[1], 1);
+
+ val =
+ fdtdec_get_int(gd->fdt_blob, pin_node, "direction", -1);
+ if (val != -1)
+ _ich6_gpio_set_direction(GPIO_IOSEL_OFFSET
+ (gpiobase) +
+ gpio_offset[0],
+ gpio_offset[1], val);
+
+ val =
+ fdtdec_get_int(gd->fdt_blob, pin_node, "output-value", -1);
+ if (val != -1)
+ _ich6_gpio_set_value(GPIO_LVL_OFFSET(gpiobase)
+ + gpio_offset[0],
+ gpio_offset[1], val);
+ }
+
+ /* if iobase is present, let's configure the pad */
+ if (iobase != -1) {
+ int iobase_addr;
+
+ /*
+ * The offset for the same pin for the IOBASE and GPIOBASE are
+ * different, so instead of maintaining a lookup table,
+ * the device tree should provide directly the correct
+ * value for both mapping.
+ */
+ pad_offset =
+ fdtdec_get_int(gd->fdt_blob, pin_node, "pad-offset", -1);
+ if (pad_offset == -1) {
+ debug("%s: Invalid register io offset %d\n",
+ __func__, pad_offset);
+ return -EINVAL;
+ }
+
+ /* compute the absolute pad address */
+ iobase_addr = iobase + pad_offset;
+
+ /*
+ * Do we need to set a specific function mode?
+ * If someone put also 'mode-gpio', this option will
+ * be just ignored by the controller
+ */
+ val = fdtdec_get_int(gd->fdt_blob, pin_node, "mode-func", -1);
+ if (val != -1)
+ clrsetbits_le32(iobase_addr, IOPAD_MODE_MASK, val);
+
+ /* Configure the pull-up/down if needed */
+ val = fdtdec_get_int(gd->fdt_blob, pin_node, "pull-assign", -1);
+ if (val != -1)
+ clrsetbits_le32(iobase_addr,
+ IOPAD_PULL_ASSIGN_MASK,
+ val << IOPAD_PULL_ASSIGN_SHIFT);
+
+ val =
+ fdtdec_get_int(gd->fdt_blob, pin_node, "pull-strength", -1);
+ if (val != -1)
+ clrsetbits_le32(iobase_addr,
+ IOPAD_PULL_STRENGTH_MASK,
+ val << IOPAD_PULL_STRENGTH_SHIFT);
+
+ debug("%s: pad cfg [0x%x]: %08x\n", __func__, pad_offset,
+ readl(iobase_addr));
+ }
+
+ return 0;
+}
+
+int gpio_ich6_pinctrl_init(void)
+{
+ int pin_node;
+ int node;
+ int ret;
+ int gpiobase;
+ int iobase_offset;
+ int iobase = -1;
+
+ /*
+ * Get the memory/io base address to configure every pins.
+ * IOBASE is used to configure the mode/pads
+ * GPIOBASE is used to configure the direction and default value
+ */
+ gpiobase = gpio_ich6_get_base(PCI_CFG_GPIOBASE);
+ if (gpiobase < 0) {
+ debug("%s: invalid GPIOBASE address (%08x)\n", __func__,
+ gpiobase);
+ return -EINVAL;
+ }
+
+ /* This is not an error to not have a pinctrl node */
+ node =
+ fdtdec_next_compatible(gd->fdt_blob, 0, COMPAT_INTEL_X86_PINCTRL);
+ if (node <= 0) {
+ debug("%s: no pinctrl node\n", __func__);
+ return 0;
+ }
+
+ /*
+ * Get the IOBASE, this is not mandatory as this is not
+ * supported by all the CPU
+ */
+ iobase_offset = fdtdec_get_int(gd->fdt_blob, node, "io-base", -1);
+ if (iobase_offset == -1) {
+ debug("%s: io-base offset not present\n", __func__);
+ } else {
+ iobase = gpio_ich6_get_base(iobase_offset);
+ if (iobase < 0) {
+ debug("%s: invalid IOBASE address (%08x)\n", __func__,
+ iobase);
+ return -EINVAL;
+ }
+ }
+
+ for (pin_node = fdt_first_subnode(gd->fdt_blob, node);
+ pin_node > 0;
+ pin_node = fdt_next_subnode(gd->fdt_blob, pin_node)) {
+ /* Configure the pin */
+ ret = _gpio_ich6_pinctrl_cfg_pin(gpiobase, iobase, pin_node);
+ if (ret != 0) {
+ debug("%s: invalid configuration for the pin %d\n",
+ __func__, pin_node);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static int gpio_ich6_ofdata_to_platdata(struct udevice *dev)
+{
+ struct ich6_bank_platdata *plat = dev_get_platdata(dev);
+ u16 gpiobase;
+ int offset;
+
+ gpiobase = gpio_ich6_get_base(PCI_CFG_GPIOBASE);
offset = fdtdec_get_int(gd->fdt_blob, dev->of_offset, "reg", -1);
if (offset == -1) {
debug("%s: Invalid register offset %d\n", __func__, offset);
static int ich6_gpio_direction_input(struct udevice *dev, unsigned offset)
{
struct ich6_bank_priv *bank = dev_get_priv(dev);
- u32 tmplong;
- tmplong = inl(bank->io_sel);
- tmplong |= (1UL << offset);
- outl(bank->io_sel, tmplong);
- return 0;
+ return _ich6_gpio_set_direction(inl(bank->io_sel), offset, 0);
}
static int ich6_gpio_direction_output(struct udevice *dev, unsigned offset,
int value)
{
+ int ret;
struct ich6_bank_priv *bank = dev_get_priv(dev);
- u32 tmplong;
- gpio_set_value(offset, value);
+ ret = _ich6_gpio_set_direction(inl(bank->io_sel), offset, 1);
+ if (ret)
+ return ret;
- tmplong = inl(bank->io_sel);
- tmplong &= ~(1UL << offset);
- outl(bank->io_sel, tmplong);
- return 0;
+ return _ich6_gpio_set_value(bank->lvl, offset, value);
}
static int ich6_gpio_get_value(struct udevice *dev, unsigned offset)
-
{
struct ich6_bank_priv *bank = dev_get_priv(dev);
u32 tmplong;
int value)
{
struct ich6_bank_priv *bank = dev_get_priv(dev);
- u32 tmplong;
-
- tmplong = inl(bank->lvl);
- if (value)
- tmplong |= (1UL << offset);
- else
- tmplong &= ~(1UL << offset);
- outl(bank->lvl, tmplong);
- return 0;
+ return _ich6_gpio_set_value(bank->lvl, offset, value);
}
static int ich6_gpio_get_function(struct udevice *dev, unsigned offset)
projects / u-boot / commitdiff