select SYS_FSL_ERRATUM_A010315
select SYS_FSL_SRDS_1
select SYS_HAS_SERDES
+ select SYS_FSL_DDR_BE
+ select SYS_FSL_DDR_VER_50
menu "LS102xA architecture"
depends on ARCH_LS1021A
cores, count the reserved ports. This will allocate enough memory
in spin table to properly handle all cores.
+config NUM_DDR_CONTROLLERS
+ int "Maximum DDR controllers"
+ default 1
+
config SYS_FSL_ERRATUM_A010315
bool "Workaround for PCIe erratum A010315"
config SYS_HAS_SERDES
bool
+config SYS_FSL_DDR
+ bool "Freescale DDR driver"
+ help
+ Select Freescale General DDR driver, shared between most Freescale
+ PowerPC- based SoCs (such as mpc83xx, mpc85xx, mpc86xx) and ARM-
+ based Layerscape SoCs (such as ls2080a).
+
+config SYS_FSL_DDR_BE
+ bool
+ default y
+ help
+ Access DDR registers in big-endian.
+
+config SYS_FSL_DDR_VER
+ int
+ default 50 if SYS_FSL_DDR_VER_50
+
+config SYS_FSL_DDR_VER_50
+ bool
+
+config SYS_FSL_DDRC_ARM_GEN3
+ bool
+
+config SYS_FSL_DDRC_GEN4
+ bool
+
+config SYS_FSL_DDR3
+ bool "Freescale DDR3 controller"
+ depends on !SYS_FSL_DDR4
+ select SYS_FSL_DDR
+ select SYS_FSL_DDRC_ARM_GEN3
+ help
+ Enable Freescale DDR3 controller on ARM-based SoCs.
+
+config SYS_FSL_DDR4
+ bool "Freescale DDR4 controller"
+ select SYS_FSL_DDR
+ select SYS_FSL_DDRC_GEN4
+ help
+ Enable Freescale DDR4 controller.
+
config SYS_FSL_IFC_BANK_COUNT
int "Maximum banks of Integrated flash controller"
depends on ARCH_LS1021A
#define CONFIG_SYS_FSL_ERRATUM_A008407
#ifdef CONFIG_DDR_SPD
-#define CONFIG_SYS_FSL_DDR_BE
#define CONFIG_VERY_BIG_RAM
-#ifdef CONFIG_SYS_FSL_DDR4
-#define CONFIG_SYS_FSL_DDRC_GEN4
-#else
-#define CONFIG_SYS_FSL_DDRC_ARM_GEN3
-#endif
-#define CONFIG_SYS_FSL_DDR
#define CONFIG_SYS_LS1_DDR_BLOCK1_SIZE ((phys_size_t)2 << 30)
#define CONFIG_MAX_MEM_MAPPED CONFIG_SYS_LS1_DDR_BLOCK1_SIZE
#endif
#define DCU_LAYER_MAX_NUM 16
#ifdef CONFIG_LS102XA
-#define CONFIG_SYS_FSL_IFC_BANK_COUNT 8
-#define CONFIG_NUM_DDR_CONTROLLERS 1
-#define CONFIG_SYS_FSL_DDR_VER FSL_DDR_VER_5_0
#define CONFIG_SYS_FSL_SEC_COMPAT 5
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
#define CONFIG_SYS_FSL_ERRATUM_A008378
CONFIG_FIT_VERBOSE=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4"
+CONFIG_SYS_FSL_DDR4=y
CONFIG_BOOTDELAY=3
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
CONFIG_FIT_VERBOSE=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4,LPUART"
+CONFIG_SYS_EXTRA_OPTIONS="LPUART"
+CONFIG_SYS_FSL_DDR4=y
CONFIG_BOOTDELAY=3
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_STDOUT_VIA_ALIAS=y
CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPL_FSL_PBL,NAND_BOOT"
+CONFIG_SYS_FSL_DDR3=y
CONFIG_NAND_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_SPL=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_STDOUT_VIA_ALIAS=y
CONFIG_SYS_EXTRA_OPTIONS="SECURE_BOOT"
+CONFIG_SYS_FSL_DDR3=y
CONFIG_BOOTDELAY=3
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
CONFIG_NETDEVICES=y
CONFIG_E1000=y
CONFIG_DM_SERIAL=y
+CONFIG_SYS_FSL_DDR3=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_STDOUT_VIA_ALIAS=y
CONFIG_SYS_EXTRA_OPTIONS="LPUART"
+CONFIG_SYS_FSL_DDR3=y
CONFIG_BOOTDELAY=3
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_STDOUT_VIA_ALIAS=y
CONFIG_SYS_EXTRA_OPTIONS="QSPI_BOOT"
+CONFIG_SYS_FSL_DDR3=y
CONFIG_QSPI_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_HUSH_PARSER=y
CONFIG_FIT=y
CONFIG_FIT_VERBOSE=y
CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPL_FSL_PBL,SD_BOOT"
+CONFIG_SYS_FSL_DDR3=y
CONFIG_SD_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_SPL=y
CONFIG_FIT=y
CONFIG_FIT_VERBOSE=y
CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPL_FSL_PBL,SD_BOOT,SD_BOOT_QSPI"
+CONFIG_SYS_FSL_DDR3=y
CONFIG_SD_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_SPL=y
#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
#ifndef CONFIG_SYS_FSL_DDR4
-#define CONFIG_SYS_FSL_DDR3 /* Use DDR3 memory */
#define CONFIG_SYS_DDR_RAW_TIMING
#endif
#define CONFIG_DIMM_SLOTS_PER_CTLR 1