These have not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tolunay Orkun <torkun@nextio.com>
prompt "Target select"
optional
-config TARGET_CSB272
- bool "Support csb272"
-
-config TARGET_CSB472
- bool "Support csb472"
-
config TARGET_LWMON5
bool "Support lwmon5"
select SUPPORT_SPL
source "board/amcc/yucca/Kconfig"
source "board/avnet/fx12mm/Kconfig"
source "board/avnet/v5fx30teval/Kconfig"
-source "board/csb272/Kconfig"
-source "board/csb472/Kconfig"
source "board/esd/cpci2dp/Kconfig"
source "board/esd/cpci405/Kconfig"
source "board/esd/plu405/Kconfig"
+++ /dev/null
-if TARGET_CSB272
-
-config SYS_BOARD
- default "csb272"
-
-config SYS_CONFIG_NAME
- default "csb272"
-
-endif
+++ /dev/null
-CSB272 BOARD
-M: Tolunay Orkun <torkun@nextio.com>
-S: Maintained
-F: board/csb272/
-F: include/configs/csb272.h
-F: configs/csb272_defconfig
+++ /dev/null
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = csb272.o
-obj-y += init.o
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Tolunay Orkun, Nextio Inc., torkun@nextio.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/processor.h>
-#include <i2c.h>
-#include <miiphy.h>
-#include <asm/ppc4xx-emac.h>
-
-void sdram_init(void);
-
-/*
- * Configuration data for AMIS FS6377-01 Programmable 3-PLL Clock Generator
- *
- * CLKA output => Epson LCD Controller
- * CLKB output => Not Connected
- * CLKC output => Ethernet
- * CLKD output => UART external clock
- *
- * Note: these values are obtained from device after init by micromonitor
-*/
-uchar pll_fs6377_regs[16] = {
- 0x28, 0xef, 0x53, 0x03, 0x4b, 0x80, 0x32, 0x80,
- 0x94, 0x32, 0x80, 0xd4, 0x56, 0xf6, 0xf6, 0xe0 };
-
-/*
- * pll_init: Initialize AMIS IC FS6377-01 PLL
- *
- * PLL supplies Epson LCD Clock, Ethernet Clock and UART external clock
- *
- */
-int pll_init(void)
-{
- i2c_set_bus_num(0);
-
- return i2c_write(CONFIG_SYS_I2C_PLL_ADDR, 0, 1,
- (uchar *) pll_fs6377_regs, sizeof(pll_fs6377_regs));
-}
-
-/*
- * board_early_init_f: do early board initialization
- *
- */
-int board_early_init_f(void)
-{
- /* initialize PLL so UART, LCD, Ethernet clocked at correctly */
- (void) get_clocks();
- pll_init();
-
- /*-------------------------------------------------------------------------+
- | Interrupt controller setup for the Walnut board.
- | Note: IRQ 0-15 405GP internally generated; active high; level sensitive
- | IRQ 16 405GP internally generated; active low; level sensitive
- | IRQ 17-24 RESERVED
- | IRQ 25 (EXT IRQ 0) FPGA; active high; level sensitive
- | IRQ 26 (EXT IRQ 1) SMI; active high; level sensitive
- | IRQ 27 (EXT IRQ 2) Not Used
- | IRQ 28 (EXT IRQ 3) PCI SLOT 3; active low; level sensitive
- | IRQ 29 (EXT IRQ 4) PCI SLOT 2; active low; level sensitive
- | IRQ 30 (EXT IRQ 5) PCI SLOT 1; active low; level sensitive
- | IRQ 31 (EXT IRQ 6) PCI SLOT 0; active low; level sensitive
- | Note for Walnut board:
- | An interrupt taken for the FPGA (IRQ 25) indicates that either
- | the Mouse, Keyboard, IRDA, or External Expansion caused the
- | interrupt. The FPGA must be read to determine which device
- | caused the interrupt. The default setting of the FPGA clears
- |
- +-------------------------------------------------------------------------*/
-
- mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */
- mtdcr (UIC0ER, 0x00000000); /* disable all ints */
- mtdcr (UIC0CR, 0x00000000); /* set all to be non-critical */
- mtdcr (UIC0PR, 0xFFFFFF83); /* set int polarities */
- mtdcr (UIC0TR, 0x10000000); /* set int trigger levels */
- mtdcr (UIC0VCR, 0x00000001); /* set vect base=0,INT0 highest priority */
- mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */
-
- mtebc (EBC0_CFG, 0xa8400000); /* EBC always driven */
-
- return 0; /* success */
-}
-
-/*
- * checkboard: identify/verify the board we are running
- *
- * Remark: we just assume it is correct board here!
- *
- */
-int checkboard(void)
-{
- printf("BOARD: Cogent CSB272\n");
-
- return 0; /* success */
-}
-
-/*
- * initram: Determine the size of mounted DRAM
- *
- * Size is determined by reading SDRAM configuration registers as
- * configured by initialization code
- *
- */
-phys_size_t initdram (int board_type)
-{
- ulong tot_size;
- ulong bank_size;
- ulong tmp;
-
- /*
- * ToDo: Move the asm init routine sdram_init() to this C file,
- * or even better use some common ppc4xx code available
- * in arch/powerpc/cpu/ppc4xx
- */
- sdram_init();
-
- tot_size = 0;
-
- mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
- tmp = mfdcr (SDRAM0_CFGDATA);
- if (tmp & 0x00000001) {
- bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
- tot_size += bank_size;
- }
-
- mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR);
- tmp = mfdcr (SDRAM0_CFGDATA);
- if (tmp & 0x00000001) {
- bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
- tot_size += bank_size;
- }
-
- mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR);
- tmp = mfdcr (SDRAM0_CFGDATA);
- if (tmp & 0x00000001) {
- bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
- tot_size += bank_size;
- }
-
- mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR);
- tmp = mfdcr (SDRAM0_CFGDATA);
- if (tmp & 0x00000001) {
- bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
- tot_size += bank_size;
- }
-
- return tot_size;
-}
-
-/*
- * last_stage_init: final configurations (such as PHY etc)
- *
- */
-int last_stage_init(void)
-{
- /* initialize the PHY */
- miiphy_reset("ppc_4xx_eth0", CONFIG_PHY_ADDR);
-
- /* AUTO neg */
- miiphy_write("ppc_4xx_eth0", CONFIG_PHY_ADDR, MII_BMCR,
- BMCR_ANENABLE | BMCR_ANRESTART);
-
- /* LEDs */
- miiphy_write("ppc_4xx_eth0", CONFIG_PHY_ADDR, MII_NWAYTEST, 0x0d08);
-
-
- return 0; /* success */
-}
+++ /dev/null
-/*
- * SPDX-License-Identifier: GPL-2.0 IBM-pibs
- */
-#include <config.h>
-#include <asm/ppc4xx.h>
-
-#include <ppc_asm.tmpl>
-#include <ppc_defs.h>
-
-#include <asm/cache.h>
-#include <asm/mmu.h>
-
-#define LI32(reg,val) \
- addis reg,0,val@h;\
- ori reg,reg,val@l
-
-#define WDCR_EBC(reg,val) \
- addi r4,0,reg;\
- mtdcr EBC0_CFGADDR,r4;\
- addis r4,0,val@h;\
- ori r4,r4,val@l;\
- mtdcr EBC0_CFGDATA,r4
-
-#define WDCR_SDRAM(reg,val) \
- addi r4,0,reg;\
- mtdcr SDRAM0_CFGADDR,r4;\
- addis r4,0,val@h;\
- ori r4,r4,val@l;\
- mtdcr SDRAM0_CFGDATA,r4
-
-/******************************************************************************
- * Function: ext_bus_cntlr_init
- *
- * Description: Configures EBC Controller and a few basic chip selects.
- *
- * CS0 is setup to get the Boot Flash out of the addresss range
- * so that we may setup a stack. CS7 is setup so that we can
- * access and reset the hardware watchdog.
- *
- * IMPORTANT: For pass1 this code must run from
- * cache since you can not reliably change a peripheral banks
- * timing register (pbxap) while running code from that bank.
- * For ex., since we are running from ROM on bank 0, we can NOT
- * execute the code that modifies bank 0 timings from ROM, so
- * we run it from cache.
- *
- * Notes: Does NOT use the stack.
- *****************************************************************************/
- .section ".text"
- .align 2
- .globl ext_bus_cntlr_init
- .type ext_bus_cntlr_init, @function
-ext_bus_cntlr_init:
- mflr r0
- /********************************************************************
- * Prefetch entire ext_bus_cntrl_init function into the icache.
- * This is necessary because we are going to change the same CS we
- * are executing from. Otherwise a CPU lockup may occur.
- *******************************************************************/
- bl ..getAddr
-..getAddr:
- mflr r3 /* get address of ..getAddr */
-
- /* Calculate number of cache lines for this function */
- addi r4, 0, (((.Lfe0 - ..getAddr) / CONFIG_SYS_CACHELINE_SIZE) + 2)
- mtctr r4
-..ebcloop:
- icbt r0, r3 /* prefetch cache line for addr in r3*/
- addi r3, r3, CONFIG_SYS_CACHELINE_SIZE /* move to next cache line */
- bdnz ..ebcloop /* continue for $CTR cache lines */
-
- /********************************************************************
- * Delay to ensure all accesses to ROM are complete before changing
- * bank 0 timings. 200usec should be enough.
- * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles.
- *******************************************************************/
- addis r3, 0, 0x0
- ori r3, r3, 0xA000 /* wait 200us from reset */
- mtctr r3
-..spinlp:
- bdnz ..spinlp /* spin loop */
-
- /********************************************************************
- * SETUP CPC0_CR0
- *******************************************************************/
- LI32(r4, 0x007000c0)
- mtdcr CPC0_CR0, r4
-
- /********************************************************************
- * Setup CPC0_CR1: Change PCIINT signal to PerWE
- *******************************************************************/
- mfdcr r4, CPC0_CR1
- ori r4, r4, 0x4000
- mtdcr CPC0_CR1, r4
-
- /********************************************************************
- * Setup External Bus Controller (EBC).
- *******************************************************************/
- WDCR_EBC(EBC0_CFG, 0xd84c0000)
- /********************************************************************
- * Memory Bank 0 (Intel 28F128J3 Flash) initialization
- *******************************************************************/
- /*WDCR_EBC(PB1AP, 0x02869200)*/
- WDCR_EBC(PB1AP, 0x07869200)
- WDCR_EBC(PB0CR, 0xfe0bc000)
- /********************************************************************
- * Memory Bank 1 (Holtek HT6542B PS/2) initialization
- *******************************************************************/
- WDCR_EBC(PB1AP, 0x1f869200)
- WDCR_EBC(PB1CR, 0xf0818000)
- /********************************************************************
- * Memory Bank 2 (Epson S1D13506) initialization
- *******************************************************************/
- WDCR_EBC(PB2AP, 0x05860300)
- WDCR_EBC(PB2CR, 0xf045a000)
- /********************************************************************
- * Memory Bank 3 (Philips SJA1000 CAN Controllers) initialization
- *******************************************************************/
- WDCR_EBC(PB3AP, 0x0387d200)
- WDCR_EBC(PB3CR, 0xf021c000)
- /********************************************************************
- * Memory Bank 4-7 (Unused) initialization
- *******************************************************************/
- WDCR_EBC(PB4AP, 0)
- WDCR_EBC(PB4CR, 0)
- WDCR_EBC(PB5AP, 0)
- WDCR_EBC(PB5CR, 0)
- WDCR_EBC(PB6AP, 0)
- WDCR_EBC(PB6CR, 0)
- WDCR_EBC(PB7AP, 0)
- WDCR_EBC(PB7CR, 0)
-
- /* We are all done */
- mtlr r0 /* Restore link register */
- blr /* Return to calling function */
-.Lfe0: .size ext_bus_cntlr_init,.Lfe0-ext_bus_cntlr_init
-/* end ext_bus_cntlr_init() */
-
-/******************************************************************************
- * Function: sdram_init
- *
- * Description: Configures SDRAM memory banks.
- *
- * Notes: Does NOT use the stack.
- *****************************************************************************/
- .section ".text"
- .align 2
- .globl sdram_init
- .type sdram_init, @function
-sdram_init:
-
- /*
- * Disable memory controller to allow
- * values to be changed.
- */
- WDCR_SDRAM(SDRAM0_CFG, 0x00000000)
-
- /*
- * Configure Memory Banks
- */
- WDCR_SDRAM(SDRAM0_B0CR, 0x00084001)
- WDCR_SDRAM(SDRAM0_B1CR, 0x00000000)
- WDCR_SDRAM(SDRAM0_B2CR, 0x00000000)
- WDCR_SDRAM(SDRAM0_B3CR, 0x00000000)
-
- /*
- * Set up SDTR1 (SDRAM Timing Register)
- */
- WDCR_SDRAM(SDRAM0_TR, 0x00854009)
-
- /*
- * Set RTR (Refresh Timing Register)
- */
- WDCR_SDRAM(SDRAM0_RTR, 0x10000000)
- /* WDCR_SDRAM(SDRAM0_RTR, 0x05f00000) */
-
- /********************************************************************
- * Delay to ensure 200usec have elapsed since reset. Assume worst
- * case that the core is running 200Mhz:
- * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles
- *******************************************************************/
- addis r3, 0, 0x0000
- ori r3, r3, 0xA000 /* Wait >200us from reset */
- mtctr r3
-..spinlp2:
- bdnz ..spinlp2 /* spin loop */
-
- /********************************************************************
- * Set memory controller options reg, MCOPT1.
- *******************************************************************/
- WDCR_SDRAM(SDRAM0_CFG,0x80800000)
-
-..sdri_done:
- blr /* Return to calling function */
-.Lfe1: .size sdram_init,.Lfe1-sdram_init
-/* end sdram_init() */
+++ /dev/null
-if TARGET_CSB472
-
-config SYS_BOARD
- default "csb472"
-
-config SYS_CONFIG_NAME
- default "csb472"
-
-endif
+++ /dev/null
-CSB472 BOARD
-M: Tolunay Orkun <torkun@nextio.com>
-S: Maintained
-F: board/csb472/
-F: include/configs/csb472.h
-F: configs/csb472_defconfig
+++ /dev/null
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = csb472.o
-obj-y += init.o
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Tolunay Orkun, Nextio Inc., torkun@nextio.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/processor.h>
-#include <i2c.h>
-#include <miiphy.h>
-#include <asm/ppc4xx-emac.h>
-
-void sdram_init(void);
-
-/*
- * board_early_init_f: do early board initialization
- *
- */
-int board_early_init_f(void)
-{
- /*-------------------------------------------------------------------------+
- | Interrupt controller setup for the Walnut board.
- | Note: IRQ 0-15 405GP internally generated; active high; level sensitive
- | IRQ 16 405GP internally generated; active low; level sensitive
- | IRQ 17-24 RESERVED
- | IRQ 25 (EXT IRQ 0) FPGA; active high; level sensitive
- | IRQ 26 (EXT IRQ 1) SMI; active high; level sensitive
- | IRQ 27 (EXT IRQ 2) Not Used
- | IRQ 28 (EXT IRQ 3) PCI SLOT 3; active low; level sensitive
- | IRQ 29 (EXT IRQ 4) PCI SLOT 2; active low; level sensitive
- | IRQ 30 (EXT IRQ 5) PCI SLOT 1; active low; level sensitive
- | IRQ 31 (EXT IRQ 6) PCI SLOT 0; active low; level sensitive
- | Note for Walnut board:
- | An interrupt taken for the FPGA (IRQ 25) indicates that either
- | the Mouse, Keyboard, IRDA, or External Expansion caused the
- | interrupt. The FPGA must be read to determine which device
- | caused the interrupt. The default setting of the FPGA clears
- |
- +-------------------------------------------------------------------------*/
-
- mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */
- mtdcr (UIC0ER, 0x00000000); /* disable all ints */
- mtdcr (UIC0CR, 0x00000000); /* set all to be non-critical */
- mtdcr (UIC0PR, 0xFFFFFF83); /* set int polarities */
- mtdcr (UIC0TR, 0x10000000); /* set int trigger levels */
- mtdcr (UIC0VCR, 0x00000001); /* set vect base=0,INT0 highest priority */
- mtdcr (UIC0SR, 0xFFFFFFFF); /* clear all ints */
-
- mtebc (EBC0_CFG, 0xa8400000); /* EBC always driven */
-
- return 0; /* success */
-}
-
-/*
- * checkboard: identify/verify the board we are running
- *
- * Remark: we just assume it is correct board here!
- *
- */
-int checkboard(void)
-{
- printf("BOARD: Cogent CSB472\n");
-
- return 0; /* success */
-}
-
-/*
- * initram: Determine the size of mounted DRAM
- *
- * Size is determined by reading SDRAM configuration registers as
- * configured by initialization code
- *
- */
-phys_size_t initdram (int board_type)
-{
- ulong tot_size;
- ulong bank_size;
- ulong tmp;
-
- /*
- * ToDo: Move the asm init routine sdram_init() to this C file,
- * or even better use some common ppc4xx code available
- * in arch/powerpc/cpu/ppc4xx
- */
- sdram_init();
-
- tot_size = 0;
-
- mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
- tmp = mfdcr (SDRAM0_CFGDATA);
- if (tmp & 0x00000001) {
- bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
- tot_size += bank_size;
- }
-
- mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR);
- tmp = mfdcr (SDRAM0_CFGDATA);
- if (tmp & 0x00000001) {
- bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
- tot_size += bank_size;
- }
-
- mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR);
- tmp = mfdcr (SDRAM0_CFGDATA);
- if (tmp & 0x00000001) {
- bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
- tot_size += bank_size;
- }
-
- mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR);
- tmp = mfdcr (SDRAM0_CFGDATA);
- if (tmp & 0x00000001) {
- bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
- tot_size += bank_size;
- }
-
- return tot_size;
-}
-
-/*
- * last_stage_init: final configurations (such as PHY etc)
- *
- */
-int last_stage_init(void)
-{
- /* initialize the PHY */
- miiphy_reset("ppc_4xx_eth0", CONFIG_PHY_ADDR);
-
- /* AUTO neg */
- miiphy_write("ppc_4xx_eth0", CONFIG_PHY_ADDR, MII_BMCR,
- BMCR_ANENABLE | BMCR_ANRESTART);
-
- /* LEDs */
- miiphy_write("ppc_4xx_eth0", CONFIG_PHY_ADDR, MII_NWAYTEST, 0x0d08);
-
- return 0; /* success */
-}
+++ /dev/null
-/*
- * SPDX-License-Identifier: GPL-2.0 IBM-pibs
- */
-#include <config.h>
-#include <asm/ppc4xx.h>
-
-#include <ppc_asm.tmpl>
-#include <ppc_defs.h>
-
-#include <asm/cache.h>
-#include <asm/mmu.h>
-
-#define LI32(reg,val) \
- addis reg,0,val@h;\
- ori reg,reg,val@l
-
-#define WDCR_EBC(reg,val) \
- addi r4,0,reg;\
- mtdcr EBC0_CFGADDR,r4;\
- addis r4,0,val@h;\
- ori r4,r4,val@l;\
- mtdcr EBC0_CFGDATA,r4
-
-#define WDCR_SDRAM(reg,val) \
- addi r4,0,reg;\
- mtdcr SDRAM0_CFGADDR,r4;\
- addis r4,0,val@h;\
- ori r4,r4,val@l;\
- mtdcr SDRAM0_CFGDATA,r4
-
-/******************************************************************************
- * Function: ext_bus_cntlr_init
- *
- * Description: Configures EBC Controller and a few basic chip selects.
- *
- * CS0 is setup to get the Boot Flash out of the addresss range
- * so that we may setup a stack. CS7 is setup so that we can
- * access and reset the hardware watchdog.
- *
- * IMPORTANT: For pass1 this code must run from
- * cache since you can not reliably change a peripheral banks
- * timing register (pbxap) while running code from that bank.
- * For ex., since we are running from ROM on bank 0, we can NOT
- * execute the code that modifies bank 0 timings from ROM, so
- * we run it from cache.
- *
- * Notes: Does NOT use the stack.
- *****************************************************************************/
- .section ".text"
- .align 2
- .globl ext_bus_cntlr_init
- .type ext_bus_cntlr_init, @function
-ext_bus_cntlr_init:
- mflr r0
- /********************************************************************
- * Prefetch entire ext_bus_cntrl_init function into the icache.
- * This is necessary because we are going to change the same CS we
- * are executing from. Otherwise a CPU lockup may occur.
- *******************************************************************/
- bl ..getAddr
-..getAddr:
- mflr r3 /* get address of ..getAddr */
-
- /* Calculate number of cache lines for this function */
- addi r4, 0, (((.Lfe0 - ..getAddr) / CONFIG_SYS_CACHELINE_SIZE) + 2)
- mtctr r4
-..ebcloop:
- icbt r0, r3 /* prefetch cache line for addr in r3*/
- addi r3, r3, CONFIG_SYS_CACHELINE_SIZE /* move to next cache line */
- bdnz ..ebcloop /* continue for $CTR cache lines */
-
- /********************************************************************
- * Delay to ensure all accesses to ROM are complete before changing
- * bank 0 timings. 200usec should be enough.
- * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles.
- *******************************************************************/
- addis r3, 0, 0x0
- ori r3, r3, 0xA000 /* wait 200us from reset */
- mtctr r3
-..spinlp:
- bdnz ..spinlp /* spin loop */
-
- /********************************************************************
- * SETUP CPC0_CR0
- *******************************************************************/
- LI32(r4, 0x00c01030)
- mtdcr CPC0_CR0, r4
-
- /********************************************************************
- * Setup CPC0_CR1: Change PCIINT signal to PerWE
- *******************************************************************/
- mfdcr r4, CPC0_CR1
- ori r4, r4, 0x4000
- mtdcr CPC0_CR1, r4
-
- /********************************************************************
- * Setup External Bus Controller (EBC).
- *******************************************************************/
- WDCR_EBC(EBC0_CFG, 0xd84c0000)
- /********************************************************************
- * Memory Bank 0 (Intel 28F640J3 Flash) initialization
- *******************************************************************/
- /*WDCR_EBC(PB1AP, 0x03055200)*/
- /*WDCR_EBC(PB1AP, 0x04055200)*/
- WDCR_EBC(PB1AP, 0x08055200)
- WDCR_EBC(PB0CR, 0xff87a000)
- /********************************************************************
- * Memory Bank 3 (Xilinx XC95144 CPLD) initialization
- *******************************************************************/
- /*WDCR_EBC(PB3AP, 0x07869200)*/
- WDCR_EBC(PB3AP, 0x04055200)
- WDCR_EBC(PB3CR, 0xf081c000)
- /********************************************************************
- * Memory Bank 1,2,4-7 (Unused) initialization
- *******************************************************************/
- WDCR_EBC(PB1AP, 0)
- WDCR_EBC(PB1CR, 0)
- WDCR_EBC(PB2AP, 0)
- WDCR_EBC(PB2CR, 0)
- WDCR_EBC(PB4AP, 0)
- WDCR_EBC(PB4CR, 0)
- WDCR_EBC(PB5AP, 0)
- WDCR_EBC(PB5CR, 0)
- WDCR_EBC(PB6AP, 0)
- WDCR_EBC(PB6CR, 0)
- WDCR_EBC(PB7AP, 0)
- WDCR_EBC(PB7CR, 0)
-
- /* We are all done */
- mtlr r0 /* Restore link register */
- blr /* Return to calling function */
-.Lfe0: .size ext_bus_cntlr_init,.Lfe0-ext_bus_cntlr_init
-/* end ext_bus_cntlr_init() */
-
-/******************************************************************************
- * Function: sdram_init
- *
- * Description: Configures SDRAM memory banks.
- *
- * Notes: Does NOT use the stack.
- *****************************************************************************/
- .section ".text"
- .align 2
- .globl sdram_init
- .type sdram_init, @function
-sdram_init:
-
- /*
- * Disable memory controller to allow
- * values to be changed.
- */
- WDCR_SDRAM(SDRAM0_CFG, 0x00000000)
-
- /*
- * Configure Memory Banks
- */
- WDCR_SDRAM(SDRAM0_B0CR, 0x00062001)
- WDCR_SDRAM(SDRAM0_B1CR, 0x00000000)
- WDCR_SDRAM(SDRAM0_B2CR, 0x00000000)
- WDCR_SDRAM(SDRAM0_B3CR, 0x00000000)
-
- /*
- * Set up SDTR1 (SDRAM Timing Register)
- */
- WDCR_SDRAM(SDRAM0_TR, 0x00854009)
-
- /*
- * Set RTR (Refresh Timing Register)
- */
- WDCR_SDRAM(SDRAM0_RTR, 0x10000000)
- /* WDCR_SDRAM(SDRAM0_RTR, 0x05f00000) */
-
- /********************************************************************
- * Delay to ensure 200usec have elapsed since reset. Assume worst
- * case that the core is running 200Mhz:
- * 200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles
- *******************************************************************/
- addis r3, 0, 0x0000
- ori r3, r3, 0xA000 /* Wait >200us from reset */
- mtctr r3
-..spinlp2:
- bdnz ..spinlp2 /* spin loop */
-
- /********************************************************************
- * Set memory controller options reg, MCOPT1.
- *******************************************************************/
- WDCR_SDRAM(SDRAM0_CFG,0x80800000)
-
-..sdri_done:
- blr /* Return to calling function */
-.Lfe1: .size sdram_init,.Lfe1-sdram_init
-/* end sdram_init() */
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_CSB272=y
-# CONFIG_CMD_SETEXPR is not set
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_CSB472=y
-# CONFIG_CMD_SETEXPR is not set
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+csb272/csb472 powerpc ppc4xx - - Tolunay Orkun <torkun@nextio.com>
alpr powerpc ppc4xx - - Stefan Roese <sr@denx.de>
cam_enc_4xx arm arm926ejs 8d775763 2015-08-20 Heiko Schocher <hs@denx.de>
atstk1003 avr32 - e5354b8a 2015-06-10 Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Tolunay Orkun, Nextio Inc., torkun@nextio.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_405GP 1 /* This is a PPC405GP CPU */
-#define CONFIG_CSB272 1 /* on a Cogent CSB272 board */
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f() */
-#define CONFIG_LAST_STAGE_INIT 1 /* Call last_stage_init() */
-#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
-
-#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
-
-/*
- * OS Bootstrap configuration
- *
- */
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 3 /* autoboot after X seconds */
-#endif
-
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check keypress when bootdelay = 0 */
-
-#if 1
-#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND \
- "setenv bootargs console=ttyS0,38400 debug " \
- "root=/dev/ram rw ramdisk_size=4096 " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
- "bootm fe000000 fe100000"
-#endif
-
-#if 0
-#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND \
- "bootp; " \
- "setenv bootargs console=ttyS0,38400 debug " \
- "root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
- "bootm"
-#endif
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_DNS2
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_BEDBUG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-
-
-/*
- * Serial download configuration
- *
- */
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * KGDB Configuration
- *
- */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
-/*
- * Miscellaneous configurable options
- *
- */
-#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_info (bd_t) */
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * watchdog configuration
- *
- */
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * UART configuration
- *
- */
-#define CONFIG_CONS_INDEX 1 /* Use UART0 */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_serial_clock()
-
-#define CONFIG_SYS_EXT_SERIAL_CLOCK 3868400 /* use external serial clock */
-#undef CONFIG_SYS_BASE_BAUD
-#define CONFIG_BAUDRATE 38400 /* Default baud rate */
-#define CONFIG_SYS_BAUDRATE_TABLE \
- { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/*
- * I2C configuration
- *
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F /* I2C slave address */
-
-/*
- * MII PHY configuration
- *
- */
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
-#define CONFIG_PHY_CMD_DELAY 40 /* PHY COMMAND delay */
- /* 32usec min. for LXT971A */
-#define CONFIG_PHY_RESET_DELAY 300 /* PHY RESET recovery delay */
-
-/*
- * RTC configuration
- *
- * Note that DS1307 RTC is limited to 100Khz I2C bus.
- *
- */
-#define CONFIG_RTC_DS1307 /* Use Dallas 1307 RTC */
-
-/*
- * PCI stuff
- *
- */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-
-#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
-#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */
-#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
-#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */
-#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */
-#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
-
-/*
- * IDE stuff
- *
- */
-#undef CONFIG_IDE_PCMCIA /* no pcmcia interface required */
-#undef CONFIG_IDE_LED /* no led for ide supported */
-#undef CONFIG_IDE_RESET /* no reset for ide supported */
-
-/*
- * Environment configuration
- *
- */
-#define CONFIG_ENV_IS_IN_FLASH 1 /* environment is in FLASH */
-#undef CONFIG_ENV_IS_IN_NVRAM
-#undef CONFIG_ENV_IS_IN_EEPROM
-
-/*
- * General Memory organization
- *
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0xFE000000
-#define CONFIG_SYS_FLASH_SIZE 0x02000000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 KB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 KB for malloc() */
-
-#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_RAMSTART
-#endif
-
-#if defined(CONFIG_ENV_IS_IN_FLASH)
-#define CONFIG_ENV_IN_OWN_SECTOR 1 /* Give Environment own sector */
-#define CONFIG_ENV_ADDR 0xFFF00000 /* Address of Environment Sector */
-#define CONFIG_ENV_SIZE 0x00001000 /* Size of Environment */
-#define CONFIG_ENV_SECT_SIZE 0x00040000 /* Size of Environment Sector */
-#endif
-
-/*
- * FLASH Device configuration
- *
- */
-#define CONFIG_SYS_FLASH_CFI 1 /* flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* use common cfi driver */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max # of memory banks */
-#define CONFIG_SYS_FLASH_INCREMENT 0 /* there is only one bank */
-#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max # of sectors on one chip */
-#define CONFIG_SYS_FLASH_PROTECTION 1 /* hardware flash protection */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * On Chip Memory location/size
- *
- */
-#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
-#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
-
-/*
- * Global info and initial stack
- *
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of on-chip SRAM */
-#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*
- * Miscellaneous board specific definitions
- *
- */
-#define CONFIG_SYS_I2C_PLL_ADDR 0x58 /* I2C address of AMIS FS6377-01 PLL */
-#define CONFIG_I2CFAST 1 /* enable "i2cfast" env. setting */
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Tolunay Orkun, Nextio Inc., torkun@nextio.com
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_405GP 1 /* This is a PPC405GP CPU */
-#define CONFIG_CSB472 1 /* on a Cogent CSB472 board */
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f() */
-#define CONFIG_LAST_STAGE_INIT 1 /* Call last_stage_init() */
-#define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */
-
-#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
-
-/*
- * OS Bootstrap configuration
- *
- */
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 3 /* autoboot after X seconds */
-#endif
-
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check keypress when bootdelay = 0 */
-
-#if 1
-#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND \
- "setenv bootargs console=ttyS0,38400 debug " \
- "root=/dev/ram rw ramdisk_size=4096 " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
- "bootm ff800000 ff900000"
-#endif
-
-#if 0
-#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND \
- "bootp; " \
- "setenv bootargs console=ttyS0,38400 debug " \
- "root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
- "bootm"
-#endif
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_DNS2
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_BEDBUG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-
-/*
- * Serial download configuration
- *
- */
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-/*
- * KGDB Configuration
- *
- */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
-/*
- * Miscellaneous configurable options
- *
- */
-#undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_info (bd_t) */
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*
- * watchdog configuration
- *
- */
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*
- * UART configuration
- *
- */
-#define CONFIG_CONS_INDEX 1 /* Use UART0 */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_serial_clock()
-
-#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* use internal serial clock */
-#define CONFIG_SYS_BASE_BAUD 691200
-#define CONFIG_BAUDRATE 38400 /* Default baud rate */
-#define CONFIG_SYS_BAUDRATE_TABLE \
- { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/*
- * I2C configuration
- *
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F /* I2C slave address */
-
-/*
- * MII PHY configuration
- *
- */
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
-#define CONFIG_PHY_CMD_DELAY 40 /* PHY COMMAND delay */
- /* 32usec min. for LXT971A */
-#define CONFIG_PHY_RESET_DELAY 300 /* PHY RESET recovery delay */
-
-/*
- * RTC configuration
- *
- * Note that DS1307 RTC is limited to 100Khz I2C bus.
- *
- */
-#define CONFIG_RTC_DS1307 /* Use Dallas 1307 RTC */
-
-/*
- * PCI stuff
- *
- */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-
-#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
-#undef CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000 /* PCI Vendor ID: to-do!!! */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000 /* PCI Device ID: to-do!!! */
-#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */
-#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */
-#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */
-#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
-
-/*
- * IDE stuff
- *
- */
-#undef CONFIG_IDE_PCMCIA /* no pcmcia interface required */
-#undef CONFIG_IDE_LED /* no led for ide supported */
-#undef CONFIG_IDE_RESET /* no reset for ide supported */
-
-/*
- * Environment configuration
- *
- */
-#define CONFIG_ENV_IS_IN_FLASH 1 /* environment is in FLASH */
-#undef CONFIG_ENV_IS_IN_NVRAM
-#undef CONFIG_ENV_IS_IN_EEPROM
-
-/*
- * General Memory organization
- *
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0xFF800000
-#define CONFIG_SYS_FLASH_SIZE 0x00800000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 KB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 KB for malloc() */
-
-#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_RAMSTART
-#endif
-
-#if defined(CONFIG_ENV_IS_IN_FLASH)
-#define CONFIG_ENV_IN_OWN_SECTOR 1 /* Give Environment own sector */
-#define CONFIG_ENV_ADDR 0xFFF00000 /* Address of Environment Sector */
-#define CONFIG_ENV_SIZE 0x00001000 /* Size of Environment */
-#define CONFIG_ENV_SECT_SIZE 0x00040000 /* Size of Environment Sector */
-#endif
-
-/*
- * FLASH Device configuration
- *
- */
-#define CONFIG_SYS_FLASH_CFI 1 /* flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* use common cfi driver */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max # of memory banks */
-#define CONFIG_SYS_FLASH_INCREMENT 0 /* there is only one bank */
-#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max # of sectors on one chip */
-#define CONFIG_SYS_FLASH_PROTECTION 1 /* hardware flash protection */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-/*
- * On Chip Memory location/size
- *
- */
-#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
-#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
-
-/*
- * Global info and initial stack
- *
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of on-chip SRAM */
-#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*
- * Miscellaneous board specific definitions
- *
- */
-#define CONFIG_I2CFAST 1 /* enable "i2cfast" env. setting */
-
-#endif /* __CONFIG_H */
projects / u-boot / commitdiff