+++ /dev/null
-/*
- * Authors: Xiangfu Liu <xiangfu@sharism.cc>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 3 of the License, or (at your option) any later version.
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/jz4740.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static void gpio_init(void)
-{
- unsigned int i;
-
- /* Initialize NAND Flash Pins */
- __gpio_as_nand();
-
- /* Initialize SDRAM pins */
- __gpio_as_sdram_16bit_4720();
-
- /* Initialize LCD pins */
- __gpio_as_lcd_18bit();
-
- /* Initialize MSC pins */
- __gpio_as_msc();
-
- /* Initialize Other pins */
- for (i = 0; i < 7; i++) {
- __gpio_as_input(GPIO_KEYIN_BASE + i);
- __gpio_enable_pull(GPIO_KEYIN_BASE + i);
- }
-
- for (i = 0; i < 8; i++) {
- __gpio_as_output(GPIO_KEYOUT_BASE + i);
- __gpio_clear_pin(GPIO_KEYOUT_BASE + i);
- }
-
- __gpio_as_input(GPIO_KEYIN_8);
- __gpio_enable_pull(GPIO_KEYIN_8);
-
- /* enable the TP4, TP5 as UART0 */
- __gpio_jtag_to_uart0();
-
- __gpio_as_output(GPIO_AUDIO_POP);
- __gpio_set_pin(GPIO_AUDIO_POP);
-
- __gpio_as_output(GPIO_LCD_CS);
- __gpio_clear_pin(GPIO_LCD_CS);
-
- __gpio_as_output(GPIO_AMP_EN);
- __gpio_clear_pin(GPIO_AMP_EN);
-
- __gpio_as_output(GPIO_SDPW_EN);
- __gpio_disable_pull(GPIO_SDPW_EN);
- __gpio_clear_pin(GPIO_SDPW_EN);
-
- __gpio_as_input(GPIO_SD_DETECT);
- __gpio_disable_pull(GPIO_SD_DETECT);
-
- __gpio_as_input(GPIO_USB_DETECT);
- __gpio_enable_pull(GPIO_USB_DETECT);
-}
-
-static void cpm_init(void)
-{
- struct jz4740_cpm *cpm = (struct jz4740_cpm *)JZ4740_CPM_BASE;
- uint32_t reg = readl(&cpm->clkgr);
-
- reg |= CPM_CLKGR_IPU |
- CPM_CLKGR_CIM |
- CPM_CLKGR_I2C |
- CPM_CLKGR_SSI |
- CPM_CLKGR_UART1 |
- CPM_CLKGR_SADC |
- CPM_CLKGR_UHC |
- CPM_CLKGR_UDC |
- CPM_CLKGR_AIC1;
-
- writel(reg, &cpm->clkgr);
-}
-
-int board_early_init_f(void)
-{
- gpio_init();
- cpm_init();
- calc_clocks(); /* calc the clocks */
- rtc_init(); /* init rtc on any reset */
-
- return 0;
-}
-
-/* U-Boot common routines */
-int checkboard(void)
-{
- printf("Board: Qi LB60 (Ingenic XBurst Jz4740 SoC, Speed %ld MHz)\n",
- gd->cpu_clk / 1000000);
-
- return 0;
-}
+++ /dev/null
-/*
- * Authors: Xiangfu Liu <xiangfu.z@gmail.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 3 of the License, or (at your option) any later version.
- */
-
-#ifndef __CONFIG_QI_LB60_H
-#define __CONFIG_QI_LB60_H
-
-#define CONFIG_MIPS32 /* MIPS32 CPU core */
-#define CONFIG_SYS_LITTLE_ENDIAN
-#define CONFIG_JZSOC /* Jz SoC */
-#define CONFIG_JZ4740 /* Jz4740 SoC */
-#define CONFIG_NAND_JZ4740
-
-#define CONFIG_SYS_CPU_SPEED 336000000 /* CPU clock: 336 MHz */
-#define CONFIG_SYS_EXTAL 12000000 /* EXTAL freq: 12 MHz */
-#define CONFIG_SYS_HZ (CONFIG_SYS_EXTAL / 256) /* incrementer freq */
-#define CONFIG_SYS_MIPS_TIMER_FREQ CONFIG_SYS_CPU_SPEED
-
-#define CONFIG_SYS_UART_BASE JZ4740_UART0_BASE /* Base of the UART channel */
-#define CONFIG_BAUDRATE 57600
-
-#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_SYS_FLASH_BASE 0 /* init flash_base as 0 */
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAUL)
-#define CONFIG_BOOTDELAY 0
-#define CONFIG_BOOTARGS "mem=32M console=tty0 console=ttyS0,57600n8 ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait"
-#define CONFIG_BOOTCOMMAND "nand read 0x80600000 0x400000 0x200000;bootm"
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_BOOTD /* bootd */
-#define CONFIG_CMD_CONSOLE /* coninfo */
-#define CONFIG_CMD_ECHO /* echo arguments */
-
-#define CONFIG_CMD_LOADB /* loadb */
-#define CONFIG_CMD_LOADS /* loads */
-#define CONFIG_CMD_MEMORY /* md mm nm mw cp cmp crc base loop mtest */
-#define CONFIG_CMD_MISC /* Misc functions like sleep etc*/
-#define CONFIG_CMD_RUN /* run command in env variable */
-#define CONFIG_CMD_SAVEENV /* saveenv */
-#define CONFIG_CMD_SETGETDCR /* DCR support on 4xx */
-#define CONFIG_CMD_SOURCE /* "source" command support */
-#define CONFIG_CMD_NAND
-
-/*
- * Serial download configuration
- */
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_SYS_PROMPT "NanoNote# "
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-
-#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
-#define CONFIG_SYS_BOOTPARAMS_LEN (128 * 1024)
-
-#define CONFIG_SYS_SDRAM_BASE 0x80000000 /* Cached addr */
-#define CONFIG_SYS_INIT_SP_OFFSET 0x400000
-#define CONFIG_SYS_LOAD_ADDR 0x80600000
-#define CONFIG_SYS_MEMTEST_START 0x80100000
-#define CONFIG_SYS_MEMTEST_END 0x80800000
-
-/*
- * Environment
- */
-#define CONFIG_ENV_IS_IN_NAND /* use NAND for environment vars */
-
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
-/*
- * if board nand flash is 1GB, set to 1
- * if board nand flash is 2GB, set to 2
- * for change the PAGE_SIZE and BLOCK_SIZE
- * will delete when there is no 1GB flash
- */
-#define NANONOTE_NAND_SIZE 2
-
-#define CONFIG_SYS_NAND_PAGE_SIZE (2048 * NANONOTE_NAND_SIZE)
-#define CONFIG_SYS_NAND_BLOCK_SIZE (256 * NANONOTE_NAND_SIZE << 10)
-/* nand bad block was marked at this page in a block, start from 0 */
-#define CONFIG_SYS_NAND_BADBLOCK_PAGE 127
-#define CONFIG_SYS_NAND_PAGE_COUNT 128
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
-/* ECC offset position in oob area, default value is 6 if it isn't defined */
-#define CONFIG_SYS_NAND_ECC_POS (6 * NANONOTE_NAND_SIZE)
-#define CONFIG_SYS_NAND_ECCSIZE 512
-#define CONFIG_SYS_NAND_ECCBYTES 9
-#define CONFIG_SYS_NAND_ECCPOS \
- {12, 13, 14, 15, 16, 17, 18, 19,\
- 20, 21, 22, 23, 24, 25, 26, 27, \
- 28, 29, 30, 31, 32, 33, 34, 35, \
- 36, 37, 38, 39, 40, 41, 42, 43, \
- 44, 45, 46, 47, 48, 49, 50, 51, \
- 52, 53, 54, 55, 56, 57, 58, 59, \
- 60, 61, 62, 63, 64, 65, 66, 67, \
- 68, 69, 70, 71, 72, 73, 74, 75, \
- 76, 77, 78, 79, 80, 81, 82, 83}
-
-#define CONFIG_SYS_NAND_OOBSIZE 128
-#define CONFIG_SYS_NAND_BASE 0xB8000000
-#define CONFIG_SYS_ONENAND_BASE CONFIG_SYS_NAND_BASE
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl.*/
-#define CONFIG_NAND_SPL_TEXT_BASE 0x80000000
-
-/*
- * IPL (Initial Program Loader, integrated inside CPU)
- * Will load first 8k from NAND (SPL) into cache and execute it from there.
- *
- * SPL (Secondary Program Loader)
- * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
- * has to fit into 8kByte. It sets up the CPU and configures the SDRAM
- * controller and the NAND controller so that the special U-Boot image can be
- * loaded from NAND to SDRAM.
- *
- * NUB (NAND U-Boot)
- * This NAND U-Boot (NUB) is a special U-Boot version which can be started
- * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
- *
- */
-#define CONFIG_SYS_NAND_U_BOOT_DST 0x80100000 /* Load NUB to this addr */
-#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
-/* Start NUB from this addr*/
-
-/*
- * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
- */
-#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) /* Offset to RAM U-Boot image */
-#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) /* Size of RAM U-Boot image */
-
-#define CONFIG_ENV_SIZE (4 << 10)
-#define CONFIG_ENV_OFFSET \
- (CONFIG_SYS_NAND_BLOCK_SIZE + CONFIG_SYS_NAND_U_BOOT_SIZE)
-#define CONFIG_ENV_OFFSET_REDUND \
- (CONFIG_ENV_OFFSET + CONFIG_SYS_NAND_BLOCK_SIZE)
-
-#define CONFIG_SYS_TEXT_BASE 0x80100000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-
-/*
- * SDRAM Info.
- */
-#define CONFIG_NR_DRAM_BANKS 1
-
-/*
- * Cache Configuration
- */
-#define CONFIG_SYS_DCACHE_SIZE 16384
-#define CONFIG_SYS_ICACHE_SIZE 16384
-#define CONFIG_SYS_CACHELINE_SIZE 32
-
-/*
- * GPIO definition
- */
-#define GPIO_LCD_CS (2 * 32 + 21)
-#define GPIO_AMP_EN (3 * 32 + 4)
-
-#define GPIO_SDPW_EN (3 * 32 + 2)
-#define GPIO_SD_DETECT (3 * 32 + 0)
-
-#define GPIO_BUZZ_PWM (3 * 32 + 27)
-#define GPIO_USB_DETECT (3 * 32 + 28)
-
-#define GPIO_AUDIO_POP (1 * 32 + 29)
-#define GPIO_COB_TEST (1 * 32 + 30)
-
-#define GPIO_KEYOUT_BASE (2 * 32 + 10)
-#define GPIO_KEYIN_BASE (3 * 32 + 18)
-#define GPIO_KEYIN_8 (3 * 32 + 26)
-
-#define GPIO_SD_CD_N GPIO_SD_DETECT /* SD Card insert detect */
-#define GPIO_SD_VCC_EN_N GPIO_SDPW_EN /* SD Card Power Enable */
-
-#define SPEN GPIO_LCD_CS /* LCDCS :Serial command enable */
-#define SPDA (2 * 32 + 22) /* LCDSCL:Serial command clock input */
-#define SPCK (2 * 32 + 23) /* LCDSDA:Serial command data input */
-
-/* SDRAM paramters */
-#define SDRAM_BW16 1 /* Data bus width: 0-32bit, 1-16bit */
-#define SDRAM_BANK4 1 /* Banks each chip: 0-2bank, 1-4bank */
-#define SDRAM_ROW 13 /* Row address: 11 to 13 */
-#define SDRAM_COL 9 /* Column address: 8 to 12 */
-#define SDRAM_CASL 2 /* CAS latency: 2 or 3 */
-
-/* SDRAM Timings, unit: ns */
-#define SDRAM_TRAS 45 /* RAS# Active Time */
-#define SDRAM_RCD 20 /* RAS# to CAS# Delay */
-#define SDRAM_TPC 20 /* RAS# Precharge Time */
-#define SDRAM_TRWL 7 /* Write Latency Time */
-#define SDRAM_TREF 15625 /* Refresh period: 8192 cycles/64ms */
-
-#endif
projects / u-boot / commitdiff