/*
* High Level Configuration Options (easy to change)
*/
-#define CONFIG_MARVELL 1
-#define CONFIG_ARM926EJS 1 /* Basic Architecture */
#define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */
#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
#define CONFIG_KW88F6281 1 /* SOC Name */
#define CONFIG_MACH_GURUPLUG /* Machine type */
-
-#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
-#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
-#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
-
-/*
- * CLKs configurations
- */
-#define CONFIG_SYS_HZ 1000
-
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
-#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
-
-/*
- * Serial Port configuration
- * The following definitions let you select what serial you want to use
- * for your console driver.
- */
-
-#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
- 115200,230400, 460800, 921600 }
-/* auto boot */
-#define CONFIG_BOOTDELAY 3 /* default enable autoboot */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
-#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
-
-#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
- +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */
/*
* Commands configuration
*/
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PING
#define CONFIG_CMD_USB
+#define CONFIG_CMD_IDE
/*
- * NAND configuration
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
*/
-#ifdef CONFIG_CMD_NAND
-#define CONFIG_NAND_KIRKWOOD
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define NAND_MAX_CHIPS 1
-#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */
-#define NAND_ALLOW_ERASE_ALL 1
-#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */
-#endif
+#include "mv-common.h"
/*
* Environment variables configurations
"x_bootargs=console=ttyS0,115200\0" \
"x_bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs\0"
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (1024 * 128) /* 128kB for malloc() */
-/* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_SIZE 128
-
-/*
- * Other required configurations
- */
-#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */
-#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
-#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
-#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
-#define CONFIG_NR_DRAM_BANKS 4
-#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */
-#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */
-#define CONFIG_SYS_MEMTEST_START 0x00800000 /* 8M */
-#define CONFIG_SYS_MEMTEST_END 0x1fffffff /*(_512M -1) */
-#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-
/*
* Ethernet Driver configuration
*/
#ifdef CONFIG_CMD_NET
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI /* specify more that one ports available */
-#define CONFIG_MII /* expose smi ove miiphy interface */
-#define CONFIG_CMD_MII
-#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */
-#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
#define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */
#define CONFIG_PHY_BASE_ADR 0
-#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
-#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv88e1121 PHY */
#endif /* CONFIG_CMD_NET */
/*
- * USB/EHCI
+ * SATA Driver configuration
*/
-#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI /* Enable EHCI USB support */
-#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */
-#define CONFIG_EHCI_IS_TDI
-#define CONFIG_USB_STORAGE
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-#define CONFIG_SUPPORT_VFAT
-#endif /* CONFIG_CMD_USB */
+#ifdef CONFIG_MVSATA_IDE
+#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
+#endif /*CONFIG_MVSATA_IDE*/
#define CONFIG_SYS_ALT_MEMTEST
--- /dev/null
+/*
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+/*
+ * This file contains Marvell Board Specific common defincations.
+ * This file should be included in board config header file.
+ *
+ * It supports common definations for Kirkwood platform
+ * TBD: support for Orion5X platforms
+ */
+
+#ifndef _MV_COMMON_H
+#define _MV_COMMON_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_MARVELL 1
+#define CONFIG_ARM926EJS 1 /* Basic Architecture */
+
+#if defined(CONFIG_KIRKWOOD)
+#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
+#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */
+
+#define CONFIG_I2C_MVTWSI_BASE KW_TWSI_BASE
+#define MV_UART0_BASE KW_UART0_BASE
+#define MV_SATA_BASE KW_SATA_BASE
+#define MV_SATA_PORT0_OFFSET KW_SATA_PORT0_OFFSET
+#define MV_SATA_PORT1_OFFSET KW_SATA_PORT1_OFFSET
+
+#else
+#error "Unsupported SoC"
+#endif
+
+/*
+ * CLKs configurations
+ */
+#define CONFIG_SYS_HZ 1000
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1 MV_UART0_BASE
+
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you want to use
+ * for your console driver.
+ */
+
+#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
+ 115200,230400, 460800, 921600 }
+/* auto boot */
+#define CONFIG_BOOTDELAY 3 /* default enable autoboot */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
+
+#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */
+
+/*
+ * NAND configuration
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_KIRKWOOD
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CONFIG_SYS_NAND_BASE 0xD8000000 /* MV_DEFADR_NANDF */
+#define NAND_ALLOW_ERASE_ALL 1
+#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */
+#endif
+
+/*
+ * SPI Flash configuration
+ */
+#ifdef CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH 1
+#define CONFIG_HARD_SPI 1
+#define CONFIG_KIRKWOOD_SPI 1
+#define CONFIG_SPI_FLASH_MACRONIX 1
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 50000000 /*50Mhz */
+#endif
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1MiB for malloc() */
+/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE 128
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */
+#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
+#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
+#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
+#define CONFIG_NR_DRAM_BANKS 4
+#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */
+#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */
+#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
+#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* specify more that one ports available */
+#define CONFIG_MII /* expose smi ove miiphy interface */
+#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
+#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
+#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * USB/EHCI
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_KIRKWOOD
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#endif /* CONFIG_CMD_USB */
+
+/*
+ * IDE Support on SATA ports
+ */
+#ifdef CONFIG_CMD_IDE
+#define __io
+#define CONFIG_CMD_EXT2
+#define CONFIG_MVSATA_IDE
+#define CONFIG_IDE_PREINIT
+#define CONFIG_MVSATA_IDE_USE_PORT1
+/* Needs byte-swapping for ATA data register */
+#define CONFIG_IDE_SWAP_IO
+/* Data, registers and alternate blocks are at the same offset */
+#define CONFIG_SYS_ATA_DATA_OFFSET (0x0100)
+#define CONFIG_SYS_ATA_REG_OFFSET (0x0100)
+#define CONFIG_SYS_ATA_ALT_OFFSET (0x0100)
+/* Each 8-bit ATA register is aligned to a 4-bytes address */
+#define CONFIG_SYS_ATA_STRIDE 4
+/* Controller supports 48-bits LBA addressing */
+#define CONFIG_LBA48
+/* CONFIG_CMD_IDE requires some #defines for ATA registers */
+#define CONFIG_SYS_IDE_MAXBUS 2
+#define CONFIG_SYS_IDE_MAXDEVICE 2
+/* ATA registers base is at SATA controller base */
+#define CONFIG_SYS_ATA_BASE_ADDR MV_SATA_BASE
+#endif /* CONFIG_CMD_IDE */
+
+/*
+ * I2C related stuff
+ */
+#ifdef CONFIG_CMD_I2C
+#define CONFIG_I2C_MVTWSI
+#define CONFIG_SYS_I2C_SLAVE 0x0
+#define CONFIG_SYS_I2C_SPEED 100000
+#endif
+
+/*
+ * File system
+ */
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_RBTREE
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_LZO
+
+#endif /* _MV_COMMON_H */
/*
* High Level Configuration Options (easy to change)
*/
-#define CONFIG_MARVELL 1
-#define CONFIG_ARM926EJS 1 /* Basic Architecture */
#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
#define CONFIG_KW88F6281 1 /* SOC Name */
#define CONFIG_MACH_MV88F6281GTW_GE /* Machine type */
-
-#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
-#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
-#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */
-#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
-/*
- * CLKs configurations
- */
-#define CONFIG_SYS_HZ 1000
-
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
-#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
-
-/*
- * Serial Port configuration
- * The following definitions let you select what serial you want to use
- * for your console driver.
- */
-
-#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
- 115200,230400, 460800, 921600 }
-/* auto boot */
-#define CONFIG_BOOTDELAY 3 /* default enable autoboot */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
-#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
-
-#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
- +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */
/*
* Commands configuration
*/
#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
#include <config_cmd_default.h>
-#define CONFIG_CMD_AUTOSCRIPT
#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
#define CONFIG_CMD_ENV
#define CONFIG_CMD_FAT
#define CONFIG_CMD_PING
#define CONFIG_CMD_USB
/*
- * Flash configuration
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
*/
-#ifdef CONFIG_CMD_SF
-#define CONFIG_SPI_FLASH 1
-#define CONFIG_HARD_SPI 1
-#define CONFIG_KIRKWOOD_SPI 1
-#define CONFIG_SPI_FLASH_MACRONIX 1
-#define CONFIG_ENV_SPI_BUS 0
-#define CONFIG_ENV_SPI_CS 0
-#define CONFIG_ENV_SPI_MAX_HZ 50000000 /*50Mhz */
-#endif
+#include "mv-common.h"
+
+/* Unwanted stuffs from mv-common.h */
+#undef CONFIG_CMD_EXT2
+#undef CONFIG_CMD_JFFS2
+#undef CONFIG_CMD_FAT
+#undef CONFIG_CMD_UBI
+#undef CONFIG_CMD_UBIFS
+#undef CONFIG_RBTREE
/*
* Environment variables configurations
"x_bootcmd_usb=usb start\0" \
"x_bootargs_root=root=/dev/mtdblock3 ro rootfstype=squashfs\0"
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (1024 * 128) /* 128kB for malloc() */
-/* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_SIZE 128
-
-/*
- * Other required minimal configurations
- */
-#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */
-#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
-#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
-#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
-#define CONFIG_NR_DRAM_BANKS 4
-#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */
-#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */
-#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
-#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
-#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-
/*
* Ethernet Driver configuration
*/
#ifdef CONFIG_CMD_NET
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PING
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI /* specify more that one ports available */
-#define CONFIG_MII /* expose smi ove miiphy interface */
-#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */
-#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
-#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
-#endif /* CONFIG_CMD_NET */
-
-/*
- * Marvell 88Exxxx Switch configurations
- */
-#define CONFIG_RESET_PHY_R /* use reset_phy() to init phy/swtich */
#define CONFIG_MV88E61XX_SWITCH /* Enable mv88e61xx switch driver */
-
-/*
- * USB/EHCI
- */
-#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI /* Enable EHCI USB support */
-#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */
-#define CONFIG_EHCI_IS_TDI
-#define CONFIG_USB_STORAGE
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-#define CONFIG_SUPPORT_VFAT
-#endif /* CONFIG_CMD_USB */
+#endif /* CONFIG_CMD_NET */
#endif /* _CONFIG_MV88F6281GTW_GE_H */
/*
* High Level Configuration Options (easy to change)
*/
-#define CONFIG_MARVELL 1
-#define CONFIG_ARM926EJS 1 /* Basic Architecture */
#define CONFIG_SHEEVA_88SV131 1 /* CPU Core subversion */
#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
#define CONFIG_KW88F6281 1 /* SOC Name */
#define CONFIG_MACH_OPENRD_BASE /* Machine type */
-
-#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
-#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
-#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
-#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */
-
-/*
- * CLKs configurations
- */
-#define CONFIG_SYS_HZ 1000
-
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
-#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
-
-/*
- * Serial Port configuration
- * The following definitions let you select what serial you want to use
- * for your console driver.
- */
-
-#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
- 115200,230400, 460800, 921600 }
-/* auto boot */
-#define CONFIG_BOOTDELAY 3 /* default enable autoboot */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
-#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
-#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
- +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */
/*
* Commands configuration
*/
#define CONFIG_CMD_IDE
/*
- * NAND configuration
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
*/
-#ifdef CONFIG_CMD_NAND
-#define CONFIG_NAND_KIRKWOOD
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define NAND_MAX_CHIPS 1
-#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */
-#define NAND_ALLOW_ERASE_ALL 1
-#endif
+#include "mv-common.h"
/*
* Environment variables configurations
"mtdids="MTDIDS_DEFAULT"\0" \
"mtdparts="MTDPARTS_DEFAULT"\0"
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1MiB for malloc() */
-/* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_SIZE 128
-
-/*
- * Other required minimal configurations
- */
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
-#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
-#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
-#define CONFIG_NR_DRAM_BANKS 4
-#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */
-#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */
-#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
-#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
-#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-
/*
* Ethernet Driver configuration
*/
#ifdef CONFIG_CMD_NET
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI /* specify more that one ports available */
-#define CONFIG_MII /* expose smi ove miiphy interface */
-#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */
-#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
#define CONFIG_PHY_BASE_ADR 0x8
-#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
-#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */
#endif /* CONFIG_CMD_NET */
/*
- * USB/EHCI
- */
-#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI /* Enable EHCI USB support */
-#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */
-#define CONFIG_EHCI_IS_TDI
-#define CONFIG_USB_STORAGE
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-#define CONFIG_SUPPORT_VFAT
-#endif /* CONFIG_CMD_USB */
-
-/*
- * IDe Support on SATA port0
- */
-#ifdef CONFIG_CMD_IDE
-#define __io
-#define CONFIG_CMD_EXT2
-#define CONFIG_MVSATA_IDE
-#define CONFIG_IDE_PREINIT
-#define CONFIG_MVSATA_IDE_USE_PORT1
-/* Needs byte-swapping for ATA data register */
-#define CONFIG_IDE_SWAP_IO
-/* Data, registers and alternate blocks are at the same offset */
-#define CONFIG_SYS_ATA_DATA_OFFSET (0x0100)
-#define CONFIG_SYS_ATA_REG_OFFSET (0x0100)
-#define CONFIG_SYS_ATA_ALT_OFFSET (0x0100)
-/* Each 8-bit ATA register is aligned to a 4-bytes address */
-#define CONFIG_SYS_ATA_STRIDE 4
-/* Controller supports 48-bits LBA addressing */
-#define CONFIG_LBA48
-/* CONFIG_CMD_IDE requires some #defines for ATA registers */
-#define CONFIG_SYS_IDE_MAXBUS 2
-#define CONFIG_SYS_IDE_MAXDEVICE 2
-/* ATA registers base is at SATA controller base */
-#define CONFIG_SYS_ATA_BASE_ADDR KW_SATA_BASE
-/* ATA bus 0 is Kirkwood port 0 on openrd */
-#define CONFIG_SYS_ATA_IDE0_OFFSET KW_SATA_PORT0_OFFSET
-/* ATA bus 1 is Kirkwood port 1 on openrd */
-#define CONFIG_SYS_ATA_IDE1_OFFSET KW_SATA_PORT1_OFFSET
-#endif /* CONFIG_CMD_IDE */
-
-/*
- * File system
+ * SATA Driver configuration
*/
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_UBI
-#define CONFIG_CMD_UBIFS
-#define CONFIG_RBTREE
-#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
-#define CONFIG_MTD_PARTITIONS
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_LZO
+#ifdef CONFIG_MVSATA_IDE
+#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
+#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
+#endif /*CONFIG_MVSATA_IDE*/
#endif /* _CONFIG_OPENRD_BASE_H */
/*
* High Level Configuration Options (easy to change)
*/
-#define CONFIG_MARVELL 1
-#define CONFIG_ARM926EJS 1 /* Basic Architecture */
#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
#define CONFIG_KW88F6281 1 /* SOC Name */
#define CONFIG_MACH_RD6281A /* Machine type */
-
-#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
-#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
-#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
-
-/*
- * CLKs configurations
- */
-#define CONFIG_SYS_HZ 1000
-
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
-#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
-
-/*
- * Serial Port configuration
- * The following definitions let you select what serial you want to use
- * for your console driver.
- */
-
-#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
- 115200,230400, 460800, 921600 }
-/* auto boot */
-#define CONFIG_BOOTDELAY 3 /* default enable autoboot */
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
-#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
-
-#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
- +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */
/*
* Commands configuration
*/
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PING
#define CONFIG_CMD_USB
+#define CONFIG_CMD_IDE
/*
- * NAND configuration
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
*/
-#ifdef CONFIG_CMD_NAND
-#define CONFIG_NAND_KIRKWOOD
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define NAND_MAX_CHIPS 1
-#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */
-#define NAND_ALLOW_ERASE_ALL 1
-#endif
+#include "mv-common.h"
/*
* Environment variables configurations
"x_bootcmd_usb=usb start\0" \
"x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2\0"
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (1024 * 128) /* 128kB for malloc() */
-/* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_SIZE 128
-
-/*
- * Other required minimal configurations
- */
-#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */
-#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
-#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
-#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
-#define CONFIG_NR_DRAM_BANKS 4
-#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */
-#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */
-#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
-#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
-#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-
/*
* Ethernet Driver configuration
*/
#ifdef CONFIG_CMD_NET
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI /* specify more that one ports available */
-#define CONFIG_MII /* expose smi ove miiphy interface */
-#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */
#define CONFIG_MVGBE_PORTS {1, 1} /* enable both ports */
#define CONFIG_MV88E61XX_MULTICHIP_ADRMODE
#define CONFIG_DIS_AUTO_NEG_SPEED_GMII /*Disable Auto speed negociation */
#define CONFIG_PHY_SPEED _1000BASET /*Force PHYspeed to 1GBPs */
#define CONFIG_PHY_BASE_ADR 0x0A
-#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
-#define CONFIG_RESET_PHY_R /* use reset_phy() to init switch and PHY */
#define CONFIG_MV88E61XX_SWITCH /* Enable MV88E61XX switch driver */
#endif /* CONFIG_CMD_NET */
/*
- * USB/EHCI
+ * SATA Driver configuration
*/
-#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI /* Enable EHCI USB support */
-#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */
-#define CONFIG_EHCI_IS_TDI
-#define CONFIG_USB_STORAGE
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-#define CONFIG_SUPPORT_VFAT
-#endif /* CONFIG_CMD_USB */
+#ifdef CONFIG_MVSATA_IDE
+#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
+#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
+#endif /*CONFIG_MVSATA_IDE*/
#endif /* _CONFIG_RD6281A_H */
/*
* High Level Configuration Options (easy to change)
*/
-#define CONFIG_MARVELL 1
-#define CONFIG_ARM926EJS 1 /* Basic Architecture */
#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
#define CONFIG_KW88F6281 1 /* SOC Name */
#define CONFIG_MACH_SHEEVAPLUG /* Machine type */
-
-#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
-#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
-#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
-
-/*
- * CLKs configurations
- */
-#define CONFIG_SYS_HZ 1000
-
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
-#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
-
-/*
- * Serial Port configuration
- * The following definitions let you select what serial you want to use
- * for your console driver.
- */
-
-#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
- 115200,230400, 460800, 921600 }
-/* auto boot */
-#define CONFIG_BOOTDELAY 3 /* default enable autoboot */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
-#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
-
-#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
- +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */
/*
* Commands configuration
*/
#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */
#include <config_cmd_default.h>
-#define CONFIG_CMD_AUTOSCRIPT
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_ENV
#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PING
#define CONFIG_CMD_USB
-
/*
- * NAND configuration
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
*/
-#ifdef CONFIG_CMD_NAND
-#define CONFIG_NAND_KIRKWOOD
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define NAND_MAX_CHIPS 1
-#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */
-#define NAND_ALLOW_ERASE_ALL 1
-#endif
+#include "mv-common.h"
/*
* Environment variables configurations
"x_bootcmd_usb=usb start\0" \
"x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2\0"
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* 1 MiB for malloc() */
-/* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_SIZE 128
-
-/*
- * Other required minimal configurations
- */
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
-#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
-#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
-#define CONFIG_NR_DRAM_BANKS 4
-#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */
-#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */
-#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
-#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
-#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-
/*
* Ethernet Driver configuration
*/
#ifdef CONFIG_CMD_NET
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI /* specify more that one ports available */
-#define CONFIG_MII /* expose smi ove miiphy interface */
-#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */
-#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
#define CONFIG_PHY_BASE_ADR 0
-#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
-#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */
#endif /* CONFIG_CMD_NET */
-/*
- * USB/EHCI
- */
-#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI /* Enable EHCI USB support */
-#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */
-#define CONFIG_EHCI_IS_TDI
-#define CONFIG_USB_STORAGE
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-#define CONFIG_SUPPORT_VFAT
-#endif /* CONFIG_CMD_USB */
-
/*
* File system
*/
projects / u-boot / commitdiff