Miniarm is the internal project code. Now it is officially named Tinker board.
So rename it.
Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
rk3288-rock2-square.dtb \
rk3288-evb.dtb \
rk3288-fennec.dtb \
- rk3288-miniarm.dtb \
+ rk3288-tinker.dtb \
rk3288-popmetal.dtb \
rk3399-evb.dtb
dtb-$(CONFIG_ARCH_MESON) += \
+++ /dev/null
-/*
- * (C) Copyright 2016 Rockchip Electronics Co., Ltd
- *
- * SPDX-License-Identifier: GPL-2.0+ X11
- */
-
-/dts-v1/;
-#include "rk3288-miniarm.dtsi"
-
-/ {
- model = "Miniarm-RK3288";
- compatible = "rockchip,rk3288-miniarm", "rockchip,rk3288";
-
- chosen {
- stdout-path = &uart2;
- };
-};
-
-&dmc {
- rockchip,pctl-timing = <0x215 0xc8 0x0 0x35 0x26 0x2 0x70 0x2000d
- 0x6 0x0 0x8 0x4 0x17 0x24 0xd 0x6
- 0x4 0x8 0x4 0x76 0x4 0x0 0x30 0x0
- 0x1 0x2 0x2 0x4 0x0 0x0 0xc0 0x4
- 0x8 0x1f4>;
- rockchip,phy-timing = <0x48d7dd93 0x187008d8 0x121076
- 0x0 0xc3 0x6 0x2>;
- rockchip,sdram-params = <0x20d266a4 0x5b6 2 533000000 6 9 0>;
-};
-
-
-&pinctrl {
- u-boot,dm-pre-reloc;
-};
-
-&pwm1 {
- status = "okay";
-};
-
-&uart2 {
- u-boot,dm-pre-reloc;
- reg-shift = <2>;
-};
-
-&sdmmc {
- u-boot,dm-pre-reloc;
-};
-
-&emmc {
- u-boot,dm-pre-reloc;
-};
-
-&gpio3 {
- u-boot,dm-pre-reloc;
-};
-
-&gpio8 {
- u-boot,dm-pre-reloc;
-};
+++ /dev/null
-/*
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include "rk3288.dtsi"
-
-/ {
- memory {
- device_type = "memory";
- reg = <0x0 0x80000000>;
- };
-
- ext_gmac: external-gmac-clock {
- compatible = "fixed-clock";
- clock-frequency = <125000000>;
- clock-output-names = "ext_gmac";
- #clock-cells = <0>;
- };
-
- gpio-keys {
- compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
- autorepeat;
-
- pinctrl-names = "default";
- pinctrl-0 = <&pwrbtn>;
-
- button@0 {
- gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
- label = "GPIO Key Power";
- linux,input-type = <1>;
- gpio-key,wakeup = <1>;
- debounce-interval = <100>;
- };
- };
-
- gpio-leds {
- compatible = "gpio-leds";
-
- pwr-led {
- gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "default-on";
- };
-
- act-led {
- gpios=<&gpio2 3 GPIO_ACTIVE_LOW>;
- linux,default-trigger="mmc0";
- };
- };
-
- vcc_sys: vsys-regulator {
- compatible = "regulator-fixed";
- regulator-name = "vcc_sys";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- /*
- * NOTE: vcc_sd isn't hooked up on v1.0 boards where power comes from
- * vcc_io directly. Those boards won't be able to power cycle SD cards
- * but it shouldn't hurt to toggle this pin there anyway.
- */
- vcc_sd: sdmmc-regulator {
- compatible = "regulator-fixed";
- gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&sdmmc_pwr>;
- regulator-name = "vcc_sd";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- startup-delay-us = <100000>;
- vin-supply = <&vcc_io>;
- };
-};
-
-&cpu0 {
- cpu0-supply = <&vdd_cpu>;
-};
-
-&sdmmc {
- bus-width = <4>;
- cap-mmc-highspeed;
- cap-sd-highspeed;
- card-detect-delay = <200>;
- disable-wp; /* wp not hooked up */
- num-slots = <1>;
- pinctrl-names = "default";
- pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
- status = "okay";
- supports-sd;
- vmmc-supply = <&vcc_sd>;
- vqmmc-supply = <&vccio_sd>;
-};
-
-&gpu {
- mali-supply = <&vdd_gpu>;
- status = "okay";
-};
-
-&gmac {
- phy-supply = <&vcc33_lan>;
- phy-mode = "rgmii";
- clock_in_out = "input";
- snps,reset-gpio = <&gpio4 7 0>;
- snps,reset-active-low;
- snps,reset-delays-us = <0 10000 1000000>;
- assigned-clocks = <&cru SCLK_MAC>;
- assigned-clock-parents = <&ext_gmac>;
- pinctrl-names = "default";
- pinctrl-0 = <&rgmii_pins>;
- tx_delay = <0x30>;
- rx_delay = <0x10>;
- status = "ok";
-};
-
-&hdmi {
- ddc-i2c-bus = <&i2c5>;
- status = "okay";
-};
-
-&i2c0 {
- status = "okay";
- clock-frequency = <400000>;
-
- rk808: pmic@1b {
- compatible = "rockchip,rk808";
- reg = <0x1b>;
- interrupt-parent = <&gpio0>;
- interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&pmic_int &global_pwroff>;
- rockchip,system-power-controller;
- wakeup-source;
- #clock-cells = <1>;
- clock-output-names = "xin32k", "rk808-clkout2";
-
- vcc1-supply = <&vcc_sys>;
- vcc2-supply = <&vcc_sys>;
- vcc3-supply = <&vcc_sys>;
- vcc4-supply = <&vcc_sys>;
- vcc6-supply = <&vcc_sys>;
- vcc7-supply = <&vcc_sys>;
- vcc8-supply = <&vcc_18>;
- vcc9-supply = <&vcc_io>;
- vcc10-supply = <&vcc_io>;
- vcc11-supply = <&vcc_sys>;
- vcc12-supply = <&vcc_io>;
- vddio-supply = <&vcc18_ldo1>;
-
- regulators {
- vdd_cpu: DCDC_REG1 {
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <750000>;
- regulator-max-microvolt = <1350000>;
- regulator-name = "vdd_arm";
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- vdd_gpu: DCDC_REG2 {
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1250000>;
- regulator-name = "vdd_gpu";
- regulator-state-mem {
- regulator-on-in-suspend;
- regulator-suspend-microvolt = <1000000>;
- };
- };
-
- vcc_ddr: DCDC_REG3 {
- regulator-always-on;
- regulator-boot-on;
- regulator-name = "vcc_ddr";
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
-
- vcc_io: DCDC_REG4 {
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc_io";
- regulator-state-mem {
- regulator-on-in-suspend;
- regulator-suspend-microvolt = <3300000>;
- };
- };
-
- vcc18_ldo1: LDO_REG1 {
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-name = "vcc18_ldo1";
- regulator-state-mem {
- regulator-on-in-suspend;
- regulator-suspend-microvolt = <1800000>;
- };
- };
-
- vcc33_mipi: LDO_REG2 {
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc33_mipi";
- regulator-state-mem {
- regulator-off-in-suspend;
- };
- };
-
- vdd_10: LDO_REG3 {
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-name = "vdd_10";
- regulator-state-mem {
- regulator-on-in-suspend;
- regulator-suspend-microvolt = <1000000>;
- };
- };
-
- vcc18_codec: LDO_REG4 {
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-name = "vcc18_codec";
- regulator-state-mem {
- regulator-on-in-suspend;
- regulator-suspend-microvolt = <1800000>;
- };
- };
-
- vccio_sd: LDO_REG5 {
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vccio_sd";
- regulator-state-mem {
- regulator-on-in-suspend;
- regulator-suspend-microvolt = <3300000>;
- };
- };
-
- vdd10_lcd: LDO_REG6 {
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-name = "vdd10_lcd";
- regulator-state-mem {
- regulator-on-in-suspend;
- regulator-suspend-microvolt = <1000000>;
- };
- };
-
- vcc_18: LDO_REG7 {
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-name = "vcc_18";
- regulator-state-mem {
- regulator-on-in-suspend;
- regulator-suspend-microvolt = <1800000>;
- };
- };
-
- vcc18_lcd: LDO_REG8 {
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-name = "vcc18_lcd";
- regulator-state-mem {
- regulator-on-in-suspend;
- regulator-suspend-microvolt = <1800000>;
- };
- };
-
- vcc33_sd: SWITCH_REG1 {
- regulator-always-on;
- regulator-boot-on;
- regulator-name = "vcc33_sd";
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
-
- vcc33_lan: SWITCH_REG2 {
- regulator-always-on;
- regulator-boot-on;
- regulator-name = "vcc33_lan";
- regulator-state-mem {
- regulator-on-in-suspend;
- };
- };
- };
- };
-};
-
-&i2c2 {
- status = "okay";
- headset: nau8825@1a {
- compatible = "nuvoton,nau8825";
- #sound-dai-cells = <0>;
- reg = <0x1a>;
- interrupt-parent = <&gpio6>;
- interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
- nuvoton,jkdet-enable = <1>;
- nuvoton,jkdet-pull-enable = <1>;
- nuvoton,jkdet-pull-up = <0>;
- nuvoton,jkdet-polarity = <1>;
- nuvoton,vref-impedance = <2>;
- nuvoton,micbias-voltage = <6>;
- nuvoton,sar-threshold-num = <4>;
- nuvoton,sar-threshold = <0xa 0x14 0x26 0x73>;
- nuvoton,sar-hysteresis = <0>;
- nuvoton,sar-voltage = <6>;
- nuvoton,sar-compare-time = <0>;
- nuvoton,sar-sampling-time = <0>;
- nuvoton,short-key-debounce = <3>;
- nuvoton,jack-insert-debounce = <7>;
- nuvoton,jack-eject-debounce = <7>;
- clock-names = "mclk";
- clocks = <&cru SCLK_I2S0_OUT>;
- };
-};
-
-&i2c5 {
- status = "okay";
-};
-
-&wdt {
- status = "okay";
-};
-
-&pwm0 {
- status = "okay";
-};
-
-&saradc {
- vref-supply = <&vcc18_ldo1>;
- status ="okay";
-};
-
-&uart0 {
- status = "okay";
-};
-
-&uart1 {
- status = "okay";
-};
-
-&uart2 {
- status = "okay";
-};
-
-&uart3 {
- status = "okay";
-};
-
-&uart4 {
- status = "okay";
-};
-
-&tsadc {
- rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */
- rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
- status = "okay";
-};
-
-&usbphy {
- status = "okay";
-};
-
-&usb_host0_ehci {
- status = "okay";
-};
-
-&usb_host1 {
- status = "okay";
-};
-
-&usb_otg {
- status= "okay";
-};
-
-&vopb {
- status = "okay";
-};
-
-&vopb_mmu {
- status = "okay";
-};
-
-&vopl {
- status = "okay";
-};
-
-&vopl_mmu {
- status = "okay";
-};
-
-&pinctrl {
- pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
- drive-strength = <8>;
- };
-
- pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
- bias-pull-up;
- drive-strength = <8>;
- };
-
- backlight {
- bl_en: bl-en {
- rockchip,pins = <7 2 RK_FUNC_GPIO &pcfg_pull_none>;
- };
- };
-
- buttons {
- pwrbtn: pwrbtn {
- rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
- };
- };
-
- eth_phy {
- eth_phy_pwr: eth-phy-pwr {
- rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_none>;
- };
- };
-
- pmic {
- pmic_int: pmic-int {
- rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;
- };
- };
-
- sdmmc {
- /*
- * Default drive strength isn't enough to achieve even
- * high-speed mode on EVB board so bump up to 8ma.
- */
- sdmmc_bus4: sdmmc-bus4 {
- rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
- <6 17 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
- <6 18 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
- <6 19 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
- };
-
- sdmmc_clk: sdmmc-clk {
- rockchip,pins = <6 20 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
- };
-
- sdmmc_cmd: sdmmc-cmd {
- rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
- };
-
- sdmmc_pwr: sdmmc-pwr {
- rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
- };
- };
-
- usb {
- host_vbus_drv: host-vbus-drv {
- rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
- };
-
- pwr_3g: pwr-3g {
- rockchip,pins = <7 8 RK_FUNC_GPIO &pcfg_pull_none>;
- };
- };
-};
--- /dev/null
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier: GPL-2.0+ X11
+ */
+
+/dts-v1/;
+#include "rk3288-tinker.dtsi"
+
+/ {
+ model = "Tinker-RK3288";
+ compatible = "rockchip,rk3288-tinker", "rockchip,rk3288";
+
+ chosen {
+ stdout-path = &uart2;
+ };
+};
+
+&dmc {
+ rockchip,pctl-timing = <0x215 0xc8 0x0 0x35 0x26 0x2 0x70 0x2000d
+ 0x6 0x0 0x8 0x4 0x17 0x24 0xd 0x6
+ 0x4 0x8 0x4 0x76 0x4 0x0 0x30 0x0
+ 0x1 0x2 0x2 0x4 0x0 0x0 0xc0 0x4
+ 0x8 0x1f4>;
+ rockchip,phy-timing = <0x48d7dd93 0x187008d8 0x121076
+ 0x0 0xc3 0x6 0x2>;
+ rockchip,sdram-params = <0x20d266a4 0x5b6 2 533000000 6 9 0>;
+};
+
+
+&pinctrl {
+ u-boot,dm-pre-reloc;
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&uart2 {
+ u-boot,dm-pre-reloc;
+ reg-shift = <2>;
+};
+
+&sdmmc {
+ u-boot,dm-pre-reloc;
+};
+
+&emmc {
+ u-boot,dm-pre-reloc;
+};
+
+&gpio3 {
+ u-boot,dm-pre-reloc;
+};
+
+&gpio8 {
+ u-boot,dm-pre-reloc;
+};
--- /dev/null
+/*
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "rk3288.dtsi"
+
+/ {
+ memory {
+ device_type = "memory";
+ reg = <0x0 0x80000000>;
+ };
+
+ ext_gmac: external-gmac-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "ext_gmac";
+ #clock-cells = <0>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ autorepeat;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwrbtn>;
+
+ button@0 {
+ gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+ label = "GPIO Key Power";
+ linux,input-type = <1>;
+ gpio-key,wakeup = <1>;
+ debounce-interval = <100>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ pwr-led {
+ gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ act-led {
+ gpios=<&gpio2 3 GPIO_ACTIVE_LOW>;
+ linux,default-trigger="mmc0";
+ };
+ };
+
+ vcc_sys: vsys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ /*
+ * NOTE: vcc_sd isn't hooked up on v1.0 boards where power comes from
+ * vcc_io directly. Those boards won't be able to power cycle SD cards
+ * but it shouldn't hurt to toggle this pin there anyway.
+ */
+ vcc_sd: sdmmc-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio7 11 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_pwr>;
+ regulator-name = "vcc_sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ vin-supply = <&vcc_io>;
+ };
+};
+
+&cpu0 {
+ cpu0-supply = <&vdd_cpu>;
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ card-detect-delay = <200>;
+ disable-wp; /* wp not hooked up */
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+ status = "okay";
+ supports-sd;
+ vmmc-supply = <&vcc_sd>;
+ vqmmc-supply = <&vccio_sd>;
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu>;
+ status = "okay";
+};
+
+&gmac {
+ phy-supply = <&vcc33_lan>;
+ phy-mode = "rgmii";
+ clock_in_out = "input";
+ snps,reset-gpio = <&gpio4 7 0>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 1000000>;
+ assigned-clocks = <&cru SCLK_MAC>;
+ assigned-clock-parents = <&ext_gmac>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ tx_delay = <0x30>;
+ rx_delay = <0x10>;
+ status = "ok";
+};
+
+&hdmi {
+ ddc-i2c-bus = <&i2c5>;
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ rk808: pmic@1b {
+ compatible = "rockchip,rk808";
+ reg = <0x1b>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int &global_pwroff>;
+ rockchip,system-power-controller;
+ wakeup-source;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k", "rk808-clkout2";
+
+ vcc1-supply = <&vcc_sys>;
+ vcc2-supply = <&vcc_sys>;
+ vcc3-supply = <&vcc_sys>;
+ vcc4-supply = <&vcc_sys>;
+ vcc6-supply = <&vcc_sys>;
+ vcc7-supply = <&vcc_sys>;
+ vcc8-supply = <&vcc_18>;
+ vcc9-supply = <&vcc_io>;
+ vcc10-supply = <&vcc_io>;
+ vcc11-supply = <&vcc_sys>;
+ vcc12-supply = <&vcc_io>;
+ vddio-supply = <&vcc18_ldo1>;
+
+ regulators {
+ vdd_cpu: DCDC_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-name = "vdd_arm";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-name = "vdd_gpu";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc_ddr";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_io: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_io";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc18_ldo1: LDO_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc18_ldo1";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc33_mipi: LDO_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc33_mipi";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_10: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "vdd_10";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc18_codec: LDO_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc18_codec";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_sd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vdd10_lcd: LDO_REG6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "vdd10_lcd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc_18: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_18";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc18_lcd: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc18_lcd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc33_sd: SWITCH_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc33_sd";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc33_lan: SWITCH_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc33_lan";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&i2c2 {
+ status = "okay";
+ headset: nau8825@1a {
+ compatible = "nuvoton,nau8825";
+ #sound-dai-cells = <0>;
+ reg = <0x1a>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+ nuvoton,jkdet-enable = <1>;
+ nuvoton,jkdet-pull-enable = <1>;
+ nuvoton,jkdet-pull-up = <0>;
+ nuvoton,jkdet-polarity = <1>;
+ nuvoton,vref-impedance = <2>;
+ nuvoton,micbias-voltage = <6>;
+ nuvoton,sar-threshold-num = <4>;
+ nuvoton,sar-threshold = <0xa 0x14 0x26 0x73>;
+ nuvoton,sar-hysteresis = <0>;
+ nuvoton,sar-voltage = <6>;
+ nuvoton,sar-compare-time = <0>;
+ nuvoton,sar-sampling-time = <0>;
+ nuvoton,short-key-debounce = <3>;
+ nuvoton,jack-insert-debounce = <7>;
+ nuvoton,jack-eject-debounce = <7>;
+ clock-names = "mclk";
+ clocks = <&cru SCLK_I2S0_OUT>;
+ };
+};
+
+&i2c5 {
+ status = "okay";
+};
+
+&wdt {
+ status = "okay";
+};
+
+&pwm0 {
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcc18_ldo1>;
+ status ="okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&uart4 {
+ status = "okay";
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */
+ rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host1 {
+ status = "okay";
+};
+
+&usb_otg {
+ status= "okay";
+};
+
+&vopb {
+ status = "okay";
+};
+
+&vopb_mmu {
+ status = "okay";
+};
+
+&vopl {
+ status = "okay";
+};
+
+&vopl_mmu {
+ status = "okay";
+};
+
+&pinctrl {
+ pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
+ drive-strength = <8>;
+ };
+
+ pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
+ bias-pull-up;
+ drive-strength = <8>;
+ };
+
+ backlight {
+ bl_en: bl-en {
+ rockchip,pins = <7 2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ buttons {
+ pwrbtn: pwrbtn {
+ rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ eth_phy {
+ eth_phy_pwr: eth-phy-pwr {
+ rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int: pmic-int {
+ rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ sdmmc {
+ /*
+ * Default drive strength isn't enough to achieve even
+ * high-speed mode on EVB board so bump up to 8ma.
+ */
+ sdmmc_bus4: sdmmc-bus4 {
+ rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <6 17 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <6 18 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
+ <6 19 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+
+ sdmmc_clk: sdmmc-clk {
+ rockchip,pins = <6 20 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
+ };
+
+ sdmmc_cmd: sdmmc-cmd {
+ rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
+ };
+
+ sdmmc_pwr: sdmmc-pwr {
+ rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb {
+ host_vbus_drv: host-vbus-drv {
+ rockchip,pins = <0 14 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ pwr_3g: pwr-3g {
+ rockchip,pins = <7 8 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
writel(val, CPU_AXI_QOS_PRIORITY + VIO1_VOP_QOS);
if (!fdt_node_check_compatible(gd->fdt_blob, 0,
- "rockchip,rk3288-miniarm"))
+ "rockchip,rk3288-tinker"))
{
/* set isp qos to higher priority */
writel(val, CPU_AXI_QOS_PRIORITY + VIO1_ISP_R_QOS);
2GB DDR3. Expansion connectors provide access to I2C, SPI, UART,
GPIOs and display interface.
-config TARGET_MINIARM_RK3288
- bool "miniarm-RK3288"
- select BOARD_LATE_INIT
+config TARGET_TINKER_RK3288
+ bool "Tinker-RK3288"
+ select BOARD_LATE_INIT
help
- Miniarm is a RK3288-based development board with 2 USB ports, HDMI,
+ Tinker is a RK3288-based development board with 2 USB ports, HDMI,
micro-SD card, audio, Gigabit Ethernet. It also includes on-board
8GB eMMC and 2GB of SDRAM. Expansion connectors provide access to
I2C, SPI, UART, GPIOs.
source "board/rockchip/fennec_rk3288/Kconfig"
-source "board/rockchip/miniarm_rk3288/Kconfig"
+source "board/rockchip/tinker_rk3288/Kconfig"
endif
+++ /dev/null
-if TARGET_MINIARM_RK3288
-
-config SYS_BOARD
- default "miniarm_rk3288"
-
-config SYS_VENDOR
- default "rockchip"
-
-config SYS_CONFIG_NAME
- default "miniarm_rk3288"
-
-config BOARD_SPECIFIC_OPTIONS # dummy
- def_bool y
-
-endif
+++ /dev/null
-MINIARM-RK3288
-M: Lin Huang <hl@rock-chips.com>
-S: Maintained
-F: board/rockchip/miniarm_rk3288
-F: include/configs/miniarm_rk3288.h
-F: configs/miniarm-rk3288_defconfig
+++ /dev/null
-#
-# (C) Copyright 2016 Rockchip Electronics Co., Ltd
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y += miniarm-rk3288.o
+++ /dev/null
-/*
- * (C) Copyright 2016 Rockchip Electronics Co., Ltd
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
--- /dev/null
+if TARGET_TINKER_RK3288
+
+config SYS_BOARD
+ default "tinker_rk3288"
+
+config SYS_VENDOR
+ default "rockchip"
+
+config SYS_CONFIG_NAME
+ default "tinker_rk3288"
+
+config BOARD_SPECIFIC_OPTIONS # dummy
+ def_bool y
+
+endif
--- /dev/null
+TINKER-RK3288
+M: Lin Huang <hl@rock-chips.com>
+S: Maintained
+F: board/rockchip/tinker_rk3288
+F: include/configs/tinker_rk3288.h
+F: configs/tinker-rk3288_defconfig
--- /dev/null
+#
+# (C) Copyright 2016 Rockchip Electronics Co., Ltd
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += tinker-rk3288.o
--- /dev/null
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_ARCH_ROCKCHIP=y
-CONFIG_SYS_MALLOC_F_LEN=0x2000
-CONFIG_ROCKCHIP_RK3288=y
-CONFIG_ROCKCHIP_SPL_BACK_TO_BROM=y
-CONFIG_TARGET_MINIARM_RK3288=y
-CONFIG_SPL_STACK_R_ADDR=0x80000
-CONFIG_DEFAULT_DEVICE_TREE="rk3288-miniarm"
-CONFIG_SILENT_CONSOLE=y
-CONFIG_CONSOLE_MUX=y
-# CONFIG_DISPLAY_CPUINFO is not set
-CONFIG_SPL_STACK_R=y
-CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x2000
-# CONFIG_CMD_IMLS is not set
-CONFIG_CMD_GPT=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_SPI=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_GPIO=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_TIME=y
-CONFIG_CMD_PMIC=y
-CONFIG_CMD_REGULATOR=y
-# CONFIG_SPL_DOS_PARTITION is not set
-# CONFIG_SPL_ISO_PARTITION is not set
-# CONFIG_SPL_EFI_PARTITION is not set
-CONFIG_SPL_PARTITION_UUIDS=y
-CONFIG_SPL_OF_CONTROL=y
-CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
-CONFIG_REGMAP=y
-CONFIG_SPL_REGMAP=y
-CONFIG_SYSCON=y
-CONFIG_SPL_SYSCON=y
-# CONFIG_SPL_SIMPLE_BUS is not set
-CONFIG_CLK=y
-CONFIG_SPL_CLK=y
-CONFIG_ROCKCHIP_GPIO=y
-CONFIG_SYS_I2C_ROCKCHIP=y
-CONFIG_MMC_DW=y
-CONFIG_MMC_DW_ROCKCHIP=y
-CONFIG_PINCTRL=y
-CONFIG_SPL_PINCTRL=y
-# CONFIG_SPL_PINCTRL_FULL is not set
-CONFIG_ROCKCHIP_RK3288_PINCTRL=y
-CONFIG_DM_PMIC=y
-CONFIG_PMIC_RK808=y
-CONFIG_DM_REGULATOR_FIXED=y
-CONFIG_REGULATOR_RK808=y
-CONFIG_PWM_ROCKCHIP=y
-CONFIG_RAM=y
-CONFIG_SPL_RAM=y
-CONFIG_DEBUG_UART=y
-CONFIG_DEBUG_UART_BASE=0xff690000
-CONFIG_DEBUG_UART_CLOCK=24000000
-CONFIG_DEBUG_UART_SHIFT=2
-CONFIG_SYS_NS16550=y
-CONFIG_SYSRESET=y
-CONFIG_USE_TINY_PRINTF=y
-CONFIG_CMD_DHRYSTONE=y
-CONFIG_ERRNO_STR=y
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_ROCKCHIP_RK3288=y
+CONFIG_ROCKCHIP_SPL_BACK_TO_BROM=y
+CONFIG_TARGET_TINKER_RK3288=y
+CONFIG_SPL_STACK_R_ADDR=0x80000
+CONFIG_DEFAULT_DEVICE_TREE="rk3288-tinker"
+CONFIG_SILENT_CONSOLE=y
+CONFIG_CONSOLE_MUX=y
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN=0x2000
+# CONFIG_CMD_IMLS is not set
+CONFIG_CMD_GPT=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_ISO_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_SPL_PARTITION_UUIDS=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_REGMAP=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_SPL_SYSCON=y
+# CONFIG_SPL_SIMPLE_BUS is not set
+CONFIG_CLK=y
+CONFIG_SPL_CLK=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_PINCTRL=y
+CONFIG_SPL_PINCTRL=y
+# CONFIG_SPL_PINCTRL_FULL is not set
+CONFIG_ROCKCHIP_RK3288_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_RK808=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_REGULATOR_RK808=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_RAM=y
+CONFIG_SPL_RAM=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_BASE=0xff690000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550=y
+CONFIG_SYSRESET=y
+CONFIG_USE_TINY_PRINTF=y
+CONFIG_CMD_DHRYSTONE=y
+CONFIG_ERRNO_STR=y
- Fennec RK3288 - use fennec-rk3288 configuration
- Firefly RK3288 - use firefly-rk3288 configuration
- Hisense Chromebook - use chromebook_jerry configuration
- - Miniarm RK3288 - use miniarm-rk3288 configuration
+ - Tinker RK3288 - use tinker-rk3288 configuration
- PopMetal RK3288 - use popmetal-rk3288 configuration
- Radxa Rock 2 - use rock2 configuration
+++ /dev/null
-/*
- * (C) Copyright 2016 Rockchip Electronics Co., Ltd
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define ROCKCHIP_DEVICE_SETTINGS
-#include <configs/rk3288_common.h>
-
-#undef BOOT_TARGET_DEVICES
-
-#define BOOT_TARGET_DEVICES(func) \
- func(MMC, mmc, 0)
-
-#define CONFIG_ENV_IS_IN_MMC
-#define CONFIG_SYS_MMC_ENV_DEV 0
-
-#define CONFIG_SYS_WHITE_ON_BLACK
-
-#endif
--- /dev/null
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define ROCKCHIP_DEVICE_SETTINGS
+#include <configs/rk3288_common.h>
+
+#undef BOOT_TARGET_DEVICES
+
+#define BOOT_TARGET_DEVICES(func) \
+ func(MMC, mmc, 0)
+
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+
+#define CONFIG_SYS_WHITE_ON_BLACK
+
+#endif
projects / u-boot / commitdiff