+++ /dev/null
-/*
- * (C) Copyright 2001-2003
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2003-2005 Arabella Software Ltd.
- * Yuli Barcohen <yuli@arabellasw.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <ioports.h>
-#include <mpc8260.h>
-#include <miiphy.h>
-
-/*
- * I/O Port configuration table
- *
- * if conf is 1, then that port pin will be configured at boot time
- * according to the five values podr/pdir/ppar/psor/pdat for that entry
- */
-
-const iop_conf_t iop_conf_tab[4][32] = {
-
- /* Port A */
- { /* conf ppar psor pdir podr pdat */
- /* PA31 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxENB */
- /* PA30 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 TxClav */
- /* PA29 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 TxSOC */
- /* PA28 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 RxENB */
- /* PA27 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxSOC */
- /* PA26 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 RxClav */
- /* PA25 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[0] */
- /* PA24 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[1] */
- /* PA23 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[2] */
- /* PA22 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[3] */
- /* PA21 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[4] */
- /* PA20 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[5] */
- /* PA19 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[6] */
- /* PA18 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXD[7] */
- /* PA17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[7] */
- /* PA16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[6] */
- /* PA15 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[5] */
- /* PA14 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[4] */
- /* PA13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[3] */
- /* PA12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[2] */
- /* PA11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[1] */
- /* PA10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXD[0] */
- /* PA9 */ { 0, 1, 1, 1, 0, 0 }, /* SMC2 TXD */
- /* PA8 */ { 0, 1, 1, 0, 0, 0 }, /* SMC2 RXD */
- /* PA7 */ { 0, 0, 0, 0, 0, 0 }, /* PA7 */
- /* PA6 */ { 0, 0, 0, 0, 0, 0 }, /* PA6 */
- /* PA5 */ { 0, 0, 0, 0, 0, 0 }, /* PA5 */
- /* PA4 */ { 0, 0, 0, 0, 0, 0 }, /* PA4 */
- /* PA3 */ { 0, 0, 0, 0, 0, 0 }, /* PA3 */
- /* PA2 */ { 0, 0, 0, 0, 0, 0 }, /* PA2 */
- /* PA1 */ { 0, 0, 0, 0, 0, 0 }, /* PA1 */
- /* PA0 */ { 0, 0, 0, 0, 0, 0 } /* PA0 */
- },
-
- /* Port B */
- { /* conf ppar psor pdir podr pdat */
- /* PB31 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TX_ER */
- /* PB30 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_DV */
- /* PB29 */ { 1, 1, 1, 1, 0, 0 }, /* FCC2 MII TX_EN */
- /* PB28 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RX_ER */
- /* PB27 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII COL */
- /* PB26 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII CRS */
- /* PB25 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[3] */
- /* PB24 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[2] */
- /* PB23 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[1] */
- /* PB22 */ { 1, 1, 0, 1, 0, 0 }, /* FCC2 MII TxD[0] */
- /* PB21 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[0] */
- /* PB20 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[1] */
- /* PB19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[2] */
- /* PB18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII RxD[3] */
- /* PB17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_DIV */
- /* PB16 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RX_ERR */
- /* PB15 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_ERR */
- /* PB14 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TX_EN */
- /* PB13 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:COL */
- /* PB12 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:CRS */
- /* PB11 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
- /* PB10 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
- /* PB9 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
- /* PB8 */ { 0, 1, 0, 0, 0, 0 }, /* FCC3:RXD */
- /* PB7 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
- /* PB6 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
- /* PB5 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
- /* PB4 */ { 0, 1, 0, 1, 0, 0 }, /* FCC3:TXD */
- /* PB3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PB2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PB1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PB0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */
- },
-
- /* Port C */
- { /* conf ppar psor pdir podr pdat */
- /* PC31 */ { 0, 0, 0, 0, 0, 0 }, /* PC31 */
- /* PC30 */ { 0, 0, 0, 0, 0, 0 }, /* PC30 */
- /* PC29 */ { 0, 1, 1, 0, 0, 0 }, /* SCC1 EN CLSN */
- /* PC28 */ { 0, 0, 0, 0, 0, 0 }, /* PC28 */
- /* PC27 */ { 0, 0, 0, 0, 0, 0 }, /* PC27 */
- /* PC26 */ { 0, 0, 0, 0, 0, 0 }, /* PC26 */
- /* PC25 */ { 0, 0, 0, 0, 0, 0 }, /* PC25 */
- /* PC24 */ { 0, 0, 0, 0, 0, 0 }, /* PC24 */
- /* PC23 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN RXCLK */
- /* PC22 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN TXCLK */
- /* PC21 */ { 0, 0, 0, 0, 0, 0 }, /* PC21 */
- /* PC20 */ { 0, 0, 0, 0, 0, 0 }, /* PC20 */
- /* PC19 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII Rx Clock (CLK13) */
- /* PC18 */ { 1, 1, 0, 0, 0, 0 }, /* FCC2 MII Tx Clock (CLK14) */
- /* PC17 */ { 0, 0, 0, 0, 0, 0 }, /* PC17 */
- /* PC16 */ { 0, 0, 0, 0, 0, 0 }, /* PC16 */
- /* PC15 */ { 0, 0, 0, 0, 0, 0 }, /* PC15 */
- /* PC14 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN RENA */
- /* PC13 */ { 0, 0, 0, 0, 0, 0 }, /* PC13 */
- /* PC12 */ { 0, 0, 0, 0, 0, 0 }, /* PC12 */
- /* PC11 */ { 0, 0, 0, 0, 0, 0 }, /* PC11 */
- /* PC10 */ { 1, 0, 0, 1, 0, 0 }, /* LXT972 MDC */
- /* PC9 */ { 1, 0, 0, 0, 0, 0 }, /* LXT972 MDIO */
- /* PC8 */ { 0, 0, 0, 0, 0, 0 }, /* PC8 */
- /* PC7 */ { 0, 0, 0, 0, 0, 0 }, /* PC7 */
- /* PC6 */ { 0, 0, 0, 0, 0, 0 }, /* PC6 */
- /* PC5 */ { 0, 0, 0, 0, 0, 0 }, /* PC5 */
- /* PC4 */ { 0, 0, 0, 0, 0, 0 }, /* PC4 */
- /* PC3 */ { 0, 0, 0, 0, 0, 0 }, /* PC3 */
- /* PC2 */ { 0, 0, 0, 0, 0, 0 }, /* PC2 */
- /* PC1 */ { 0, 0, 0, 0, 0, 0 }, /* PC1 */
- /* PC0 */ { 0, 0, 0, 0, 0, 0 }, /* PC0 */
- },
-
- /* Port D */
- { /* conf ppar psor pdir podr pdat */
- /* PD31 */ { 0, 1, 0, 0, 0, 0 }, /* SCC1 EN RxD */
- /* PD30 */ { 0, 1, 1, 1, 0, 0 }, /* SCC1 EN TxD */
- /* PD29 */ { 0, 1, 0, 1, 0, 0 }, /* SCC1 EN TENA */
- /* PD28 */ { 0, 0, 0, 0, 0, 0 }, /* PD28 */
- /* PD27 */ { 0, 0, 0, 0, 0, 0 }, /* PD27 */
- /* PD26 */ { 0, 0, 0, 0, 0, 0 }, /* PD26 */
- /* PD25 */ { 0, 0, 0, 0, 0, 0 }, /* PD25 */
- /* PD24 */ { 0, 0, 0, 0, 0, 0 }, /* PD24 */
- /* PD23 */ { 0, 0, 0, 0, 0, 0 }, /* PD23 */
- /* PD22 */ { 0, 0, 0, 0, 0, 0 }, /* PD22 */
- /* PD21 */ { 0, 0, 0, 0, 0, 0 }, /* PD21 */
- /* PD20 */ { 0, 0, 0, 0, 0, 0 }, /* PD20 */
- /* PD19 */ { 0, 0, 0, 0, 0, 0 }, /* PD19 */
- /* PD18 */ { 0, 0, 0, 0, 0, 0 }, /* PD18 */
- /* PD17 */ { 0, 1, 0, 0, 0, 0 }, /* FCC1 ATMRXPRTY */
- /* PD16 */ { 0, 1, 0, 1, 0, 0 }, /* FCC1 ATMTXPRTY */
- /* PD15 */ { 0, 1, 1, 0, 1, 0 }, /* I2C SDA */
- /* PD14 */ { 0, 1, 1, 0, 1, 0 }, /* I2C SCL */
- /* PD13 */ { 0, 0, 0, 0, 0, 0 }, /* PD13 */
- /* PD12 */ { 0, 0, 0, 0, 0, 0 }, /* PD12 */
- /* PD11 */ { 0, 0, 0, 0, 0, 0 }, /* PD11 */
- /* PD10 */ { 0, 0, 0, 0, 0, 0 }, /* PD10 */
- /* PD9 */ { 1, 1, 0, 1, 0, 0 }, /* SMC1 TXD */
- /* PD8 */ { 1, 1, 0, 0, 0, 0 }, /* SMC1 RXD */
- /* PD7 */ { 0, 0, 0, 0, 0, 0 }, /* PD7 */
- /* PD6 */ { 0, 0, 0, 0, 0, 0 }, /* PD6 */
- /* PD5 */ { 0, 0, 0, 0, 0, 0 }, /* PD5 */
- /* PD4 */ { 0, 0, 0, 0, 0, 0 }, /* PD4 */
- /* PD3 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PD2 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PD1 */ { 0, 0, 0, 0, 0, 0 }, /* pin doesn't exist */
- /* PD0 */ { 0, 0, 0, 0, 0, 0 } /* pin doesn't exist */
- }
-};
-
-#ifdef CONFIG_SYS_NVRAM_ACCESS_ROUTINE
-void *nvram_read(void *dest, long src, size_t count)
-{
- return memcpy(dest, (const void *)src, count);
-}
-
-void nvram_write(long dest, const void *src, size_t count)
-{
- vu_char *p1 = (vu_char *)(CONFIG_SYS_EEPROM + 0x1555);
- vu_char *p2 = (vu_char *)(CONFIG_SYS_EEPROM + 0x0AAA);
- vu_char *d = (vu_char *)dest;
- const uchar *s = (const uchar *)src;
-
- /* Unprotect the EEPROM */
- *p1 = 0xAA;
- *p2 = 0x55;
- *p1 = 0x80;
- *p1 = 0xAA;
- *p2 = 0x55;
- *p1 = 0x20;
- udelay(10000);
-
- /* Write the data to the EEPROM */
- while (count--) {
- *d++ = *s++;
- while (*(d - 1) != *(s - 1))
- /* wait */;
- }
-
- /* Protect the EEPROM */
- *p1 = 0xAA;
- *p2 = 0x55;
- *p1 = 0xA0;
- udelay(10000);
-}
-#endif /* CONFIG_SYS_NVRAM_ACCESS_ROUTINE */
-
-phys_size_t initdram(int board_type)
-{
- vu_char *bcsr = (vu_char *)CONFIG_SYS_BCSR;
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile memctl8260_t *memctl = &immap->im_memctl;
- vu_char *ramaddr;
- uchar c = 0xFF;
- long int msize = CONFIG_SYS_SDRAM_SIZE;
- int i;
-
- if (bcsr[4] & BCSR_PCI_MODE) { /* PCI mode selected by JP9 */
- immap->im_clkrst.car_sccr |= SCCR_PCI_MODE;
- immap->im_siu_conf.sc_siumcr =
- (immap->im_siu_conf.sc_siumcr & ~SIUMCR_LBPC11)
- | SIUMCR_LBPC01;
- }
-
-#ifndef CONFIG_SYS_RAMBOOT
- immap->im_siu_conf.sc_ppc_acr = 0x03;
- immap->im_siu_conf.sc_ppc_alrh = 0x30126745;
- immap->im_siu_conf.sc_tescr1 = 0x00004000;
-
- memctl->memc_mptpr = CONFIG_SYS_MPTPR;
-
-#ifdef CONFIG_SYS_LSDRAM_BASE
- /*
- Initialise local bus SDRAM only if the pins
- are configured as local bus pins and not as PCI.
- */
- if ((immap->im_siu_conf.sc_siumcr & SIUMCR_LBPC11) == SIUMCR_LBPC00) {
- memctl->memc_lsrt = CONFIG_SYS_LSRT;
- memctl->memc_or4 = CONFIG_SYS_LSDRAM_OR;
- memctl->memc_br4 = CONFIG_SYS_LSDRAM_BR;
- ramaddr = (vu_char *)CONFIG_SYS_LSDRAM_BASE;
- memctl->memc_lsdmr = CONFIG_SYS_LSDMR | PSDMR_OP_PREA;
- *ramaddr = c;
- memctl->memc_lsdmr = CONFIG_SYS_LSDMR | PSDMR_OP_CBRR;
- for (i = 0; i < 8; i++)
- *ramaddr = c;
- memctl->memc_lsdmr = CONFIG_SYS_LSDMR | PSDMR_OP_MRW;
- *ramaddr = c;
- memctl->memc_lsdmr = CONFIG_SYS_LSDMR | PSDMR_RFEN;
- }
-#endif /* CONFIG_SYS_LSDRAM_BASE */
-
- /* Initialise 60x bus SDRAM */
- memctl->memc_psrt = CONFIG_SYS_PSRT;
- memctl->memc_or2 = CONFIG_SYS_PSDRAM_OR;
- memctl->memc_br2 = CONFIG_SYS_PSDRAM_BR;
- /*
- * The mode data for Mode Register Write command must appear on
- * the address lines during a mode-set cycle. It is driven by
- * the memory controller, in single PowerQUICC II mode,
- * according to PSDMR[CL] and PSDMR[BL] fields. In
- * 60x-compatible mode, software must drive the correct value on
- * the address lines. BL=0 because for 64-bit port size burst
- * length must be 4.
- */
- ramaddr = (vu_char *)(CONFIG_SYS_SDRAM_BASE |
- ((CONFIG_SYS_PSDMR & PSDMR_CL_MSK) << 7) | 0x10);
- memctl->memc_psdmr = CONFIG_SYS_PSDMR | PSDMR_OP_PREA; /* Precharge all banks */
- *ramaddr = c;
- memctl->memc_psdmr = CONFIG_SYS_PSDMR | PSDMR_OP_CBRR; /* CBR refresh */
- for (i = 0; i < 8; i++)
- *ramaddr = c;
- memctl->memc_psdmr = CONFIG_SYS_PSDMR | PSDMR_OP_MRW; /* Mode Register write */
- *ramaddr = c;
- memctl->memc_psdmr = CONFIG_SYS_PSDMR | PSDMR_RFEN; /* Refresh enable */
- *ramaddr = c;
-#endif /* CONFIG_SYS_RAMBOOT */
-
- /* Return total 60x bus SDRAM size */
- return msize * 1024 * 1024;
-}
-
-int checkboard(void)
-{
- vu_char *bcsr = (vu_char *)CONFIG_SYS_BCSR;
-
- printf("Board: Zephyr ZPC.1900 Rev. %c\n", bcsr[2] + 0x40);
- return 0;
-}
+++ /dev/null
-/*
- * Copyright (C) 2003-2005 Arabella Software Ltd.
- * Yuli Barcohen <yuli@arabellasw.com>
- *
- * U-Boot configuration for Zephyr Engineering ZPC.1900 board.
- * This port was developed and tested on Revision C board.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_ZPC1900 1 /* ...on Zephyr ZPC.1900 board */
-
-#define CONFIG_SYS_TEXT_BASE 0xFE000000
-
-#define CPU_ID_STR "MPC8265"
-#define CONFIG_CPM2 1 /* Has a CPM2 */
-
-/* Allow serial number (serial#) and MAC address (ethaddr) to be overwritten */
-#define CONFIG_ENV_OVERWRITE
-
-/*
- * Select serial console configuration
- *
- * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- */
-#define CONFIG_CONS_ON_SMC /* Console is on SMC */
-#undef CONFIG_CONS_ON_SCC /* It's not on SCC */
-#undef CONFIG_CONS_NONE /* It's not on external UART */
-#define CONFIG_CONS_INDEX 1 /* SMC1 is used for console */
-
-/*
- * Select ethernet configuration
- *
- * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected,
- * then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for
- * SCC, 1-3 for FCC)
- *
- * If CONFIG_ETHER_NONE is defined, then either the ethernet routines
- * must be defined elsewhere (as for the console), or CONFIG_CMD_NET
- * must be unset.
- */
-#undef CONFIG_ETHER_ON_SCC /* Ethernet is not on SCC */
-#define CONFIG_ETHER_ON_FCC /* Ethernet is on FCC */
-#undef CONFIG_ETHER_NONE /* No external Ethernet */
-
-#ifdef CONFIG_ETHER_ON_FCC
-
-#define CONFIG_ETHER_INDEX 2 /* FCC2 is used for Ethernet */
-
-#if (CONFIG_ETHER_INDEX == 2)
-/*
- * - Rx clock is CLK13
- * - Tx clock is CLK14
- * - Select bus for bd/buffers (see 28-13)
- * - Full duplex
- */
-# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
-# define CONFIG_SYS_CPMFCR_RAMTYPE 0
-# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB)
-
-#endif /* CONFIG_ETHER_INDEX */
-
-#define CONFIG_MII /* MII PHY management */
-#define CONFIG_BITBANGMII /* Bit-banged MDIO interface */
-/*
- * GPIO pins used for bit-banged MII communications
- */
-#define MDIO_PORT 2 /* Port C */
-#define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \
- (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
-#define MDC_DECLARE MDIO_DECLARE
-
-#define MDIO_ACTIVE (iop->pdir |= 0x00400000)
-#define MDIO_TRISTATE (iop->pdir &= ~0x00400000)
-#define MDIO_READ ((iop->pdat & 0x00400000) != 0)
-
-#define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \
- else iop->pdat &= ~0x00400000
-
-#define MDC(bit) if(bit) iop->pdat |= 0x00200000; \
- else iop->pdat &= ~0x00200000
-
-#define MIIDELAY udelay(1)
-
-#endif /* CONFIG_ETHER_ON_FCC */
-
-#ifndef CONFIG_8260_CLKIN
-#define CONFIG_8260_CLKIN 66666666 /* in Hz */
-#endif
-
-#define CONFIG_BAUDRATE 38400
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#define CONFIG_BOOTCOMMAND "dhcp;bootm" /* autoboot command */
-#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=:::::eth0:dhcp"
-
-#if defined(CONFIG_CMD_KGDB)
-#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */
-#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */
-#undef CONFIG_KGDB_NONE /* define if kgdb on something else */
-#define CONFIG_KGDB_INDEX 2 /* which serial channel for kgdb */
-#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */
-#endif
-
-#define CONFIG_BZIP2 /* include support for bzip2 compressed images */
-#undef CONFIG_WATCHDOG /* disable platform specific watchdog */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x03800000 /* 1 ... 56 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */
-
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_SIZE 64
-
-#define CONFIG_SYS_IMMR 0xF0000000
-#define CONFIG_SYS_LSDRAM_BASE 0xFC000000
-#define CONFIG_SYS_FLASH_BASE 0xFE000000
-#define CONFIG_SYS_BCSR 0xFEA00000
-#define CONFIG_SYS_EEPROM 0xFEB00000
-#define CONFIG_SYS_FLSIMM_BASE 0xFF000000
-
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 32 /* max num of sects on one chip */
-
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLSIMM_BASE }
-
-#define BCSR_PCI_MODE 0x01
-
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/* Hard reset configuration word */
-#define CONFIG_SYS_HRCW_MASTER (HRCW_EBM | HRCW_BPS01| HRCW_CIP |\
- HRCW_L2CPC10 | HRCW_DPPC00 | HRCW_ISB100 |\
- HRCW_BMS | HRCW_LBPC00 | HRCW_APPC10 |\
- HRCW_MODCK_H0111 \
- ) /* 0x16848207 */
-/* No slaves */
-#define CONFIG_SYS_HRCW_SLAVE1 0
-#define CONFIG_SYS_HRCW_SLAVE2 0
-#define CONFIG_SYS_HRCW_SLAVE3 0
-#define CONFIG_SYS_HRCW_SLAVE4 0
-#define CONFIG_SYS_HRCW_SLAVE5 0
-#define CONFIG_SYS_HRCW_SLAVE6 0
-#define CONFIG_SYS_HRCW_SLAVE7 0
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-#if !defined(CONFIG_ENV_IS_IN_FLASH) && !defined(CONFIG_ENV_IS_IN_NVRAM)
-#define CONFIG_ENV_IS_IN_NVRAM 1
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-# define CONFIG_ENV_SECT_SIZE 0x10000
-# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-#else
-# define CONFIG_ENV_ADDR (CONFIG_SYS_EEPROM + 0x400)
-# define CONFIG_ENV_SIZE 0x1000
-# define CONFIG_SYS_NVRAM_ACCESS_ROUTINE
-#endif
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-#define CONFIG_SYS_HID0_INIT (HID0_ICFI)
-#define CONFIG_SYS_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE)
-
-#define CONFIG_SYS_HID2 0
-
-#define CONFIG_SYS_SIUMCR 0x42200000
-#define CONFIG_SYS_SYPCR 0xFFFFFFC3
-#define CONFIG_SYS_BCR 0x90000000
-#define CONFIG_SYS_SCCR SCCR_DFBRG01
-
-#define CONFIG_SYS_RMR RMR_CSRE
-#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
-#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
-#define CONFIG_SYS_RCCR 0
-
-#define CONFIG_SYS_PSDMR /* 0x834DA43B */0x014DA43A
-#define CONFIG_SYS_PSRT 0x0F/* 0x0C */
-#define CONFIG_SYS_LSDMR 0x0085A562
-#define CONFIG_SYS_LSRT 0x0F
-#define CONFIG_SYS_MPTPR 0x4000
-
-#define CONFIG_SYS_PSDRAM_BR (CONFIG_SYS_SDRAM_BASE | 0x00000041)
-#define CONFIG_SYS_PSDRAM_OR 0xFC0028C0
-#define CONFIG_SYS_LSDRAM_BR (CONFIG_SYS_LSDRAM_BASE | 0x00001861)
-#define CONFIG_SYS_LSDRAM_OR 0xFF803480
-
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | 0x00000801)
-#define CONFIG_SYS_OR0_PRELIM 0xFFE00856
-#define CONFIG_SYS_BR5_PRELIM (CONFIG_SYS_EEPROM | 0x00000801)
-#define CONFIG_SYS_OR5_PRELIM 0xFFFF03F6
-#define CONFIG_SYS_BR6_PRELIM (CONFIG_SYS_FLSIMM_BASE | 0x00001801)
-#define CONFIG_SYS_OR6_PRELIM 0xFF000856
-#define CONFIG_SYS_BR7_PRELIM (CONFIG_SYS_BCSR | 0x00000801)
-#define CONFIG_SYS_OR7_PRELIM 0xFFFF83F6
-
-#define CONFIG_SYS_RESET_ADDRESS 0xC0000000
-
-#endif /* __CONFIG_H */
projects / u-boot / commitdiff