#include <i2c.h>
#endif
+DECLARE_GLOBAL_DATA_PTR;
+
/* Clocks in use */
#define SCCR1_CLOCKS_EN (CLOCK_SCCR1_CFG_EN | \
CLOCK_SCCR1_LPC_EN | \
CLOCK_SCCR1_PSCFIFO_EN | \
CLOCK_SCCR1_DDR_EN | \
CLOCK_SCCR1_FEC_EN | \
+ CLOCK_SCCR1_PATA_EN | \
CLOCK_SCCR1_PCI_EN | \
CLOCK_SCCR1_TPR_EN)
fdt_fixup_memory(blob, (u64)bd->bi_memstart, (u64)bd->bi_memsize);
}
#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */
+
+#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET)
+
+void init_ide_reset (void)
+{
+ volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
+ debug ("init_ide_reset\n");
+
+ /*
+ * Clear the reset bit to reset the interface
+ * cf. RefMan MPC5121EE: 28.4.1 Resetting the ATA Bus
+ */
+ immr->pata.pata_ata_control = 0;
+ udelay(100);
+ /* Assert the reset bit to enable the interface */
+ immr->pata.pata_ata_control = FSL_ATA_CTRL_ATA_RST_B;
+ udelay(100);
+
+}
+
+void ide_set_reset (int idereset)
+{
+ volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
+ debug ("ide_set_reset(%d)\n", idereset);
+
+ if (idereset) {
+ immr->pata.pata_ata_control = 0;
+ udelay(100);
+ } else {
+ immr->pata.pata_ata_control = FSL_ATA_CTRL_ATA_RST_B;
+ udelay(100);
+ }
+}
+
+#define CALC_TIMING(t) (t + period - 1) / period
+
+int ide_preinit (void)
+{
+ volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
+ long t;
+ const struct {
+ short t0;
+ short t1;
+ short t2_8;
+ short t2_16;
+ short t2i;
+ short t4;
+ short t9;
+ short tA;
+ } pio_specs = {
+ .t0 = 600,
+ .t1 = 70,
+ .t2_8 = 290,
+ .t2_16 = 165,
+ .t2i = 0,
+ .t4 = 30,
+ .t9 = 20,
+ .tA = 50,
+ };
+ union {
+ u32 config;
+ struct {
+ u8 field1;
+ u8 field2;
+ u8 field3;
+ u8 field4;
+ }bytes;
+ }cfg;
+
+ debug ("IDE preinit using PATA peripheral at IMMR-ADDR %08x\n",
+ (u32)&immr->pata);
+
+ /* Set the reset bit to 1 to enable the interface */
+ immr->pata.pata_ata_control = FSL_ATA_CTRL_ATA_RST_B;
+
+ /* Init timings : we use PIO mode 0 timings */
+ t = 1000000000 / gd->ips_clk; /* period in ns */
+ cfg.bytes.field1 = 3;
+ cfg.bytes.field2 = 3;
+ cfg.bytes.field3 = (pio_specs.t1 + t) / t;
+ cfg.bytes.field4 = (pio_specs.t2_8 + t) / t;
+
+ immr->pata.pata_time1 = cfg.config;
+
+ cfg.bytes.field1 = (pio_specs.t2_8 + t) / t;
+ cfg.bytes.field2 = (pio_specs.tA + t) / t + 2;
+ cfg.bytes.field3 = 1;
+ cfg.bytes.field4 = (pio_specs.t4 + t) / t;
+
+ immr->pata.pata_time2 = cfg.config;
+
+ cfg.config = immr->pata.pata_time3;
+ cfg.bytes.field1 = (pio_specs.t9 + t) / t;
+
+ immr->pata.pata_time3 = cfg.config;
+ debug ("PATA preinit complete.\n");
+
+ return 0;
+}
+
+#endif /* defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET) */
#include <mpc5xxx.h>
#endif
+#ifdef CONFIG_MPC512X
+#include <mpc512x.h>
+#endif
+
#include <ide.h>
#include <ata.h>
* PATA
*/
typedef struct pata512x {
- u8 fixme[0x100];
+ /* LOCAL Registers */
+ u32 pata_time1; /* Time register 1: PIO and tx timing parameter */
+ u32 pata_time2; /* Time register 2: PIO timing parameter */
+ u32 pata_time3; /* Time register 3: PIO and MDMA timing parameter */
+ u32 pata_time4; /* Time register 4: MDMA and UDMA timing parameter */
+ u32 pata_time5; /* Time register 5: UDMA timing parameter */
+ u32 pata_time6; /* Time register 6: UDMA timing parameter */
+ u32 pata_fifo_data32; /* 32bit wide dataport to/from FIFO */
+ u32 pata_fifo_data16; /* 16bit wide dataport to/from FIFO */
+ u32 pata_fifo_fill; /* FIFO filling in halfwords (READONLY)*/
+ u32 pata_ata_control; /* ATA Interface control register */
+ u32 pata_irq_pending; /* Interrupt pending register (READONLY) */
+ u32 pata_irq_enable; /* Interrupt enable register */
+ u32 pata_irq_clear; /* Interrupt clear register (WRITEONLY)*/
+ u32 pata_fifo_alarm; /* fifo alarm threshold */
+ u32 res1[0x1A];
+ /* DRIVE Registers */
+ u32 pata_drive_data; /* drive data register*/
+ u32 pata_drive_features;/* drive features register */
+ u32 pata_drive_sectcnt; /* drive sector count register */
+ u32 pata_drive_sectnum; /* drive sector number register */
+ u32 pata_drive_cyllow; /* drive cylinder low register */
+ u32 pata_drive_cylhigh; /* drive cylinder high register */
+ u32 pata_drive_dev_head;/* drive device head register */
+ u32 pata_drive_command; /* write = drive command, read = drive status reg */
+ u32 res2[0x06];
+ u32 pata_drive_alt_stat;/* write = drive control, read = drive alt status reg */
+ u32 res3[0x09];
} pata512x_t;
/*
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_DATE
#undef CONFIG_CMD_FUSE
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_EXT2
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
#endif
+#if defined(CONFIG_CMD_IDE)
+#define CONFIG_DOS_PARTITION
+#define CONFIG_MAC_PARTITION
+#define CONFIG_ISO_PARTITION
+#endif /* defined(CONFIG_CMD_IDE) */
+
/*
* Watchdog timeout = CONFIG_SYS_WATCHDOG_VALUE * 65536 / IPS clock.
* For example, when IPS is set to 66MHz and CONFIG_SYS_WATCHDOG_VALUE is set
#define OF_TBCLK (bd->bi_busfreq / 4)
#define OF_STDOUT_PATH "/soc@80000000/serial@11300"
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff
+ *-----------------------------------------------------------------------
+ */
+
+#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for IDE not supported */
+
+#define CONFIG_IDE_RESET /* reset for IDE supported */
+#define CONFIG_IDE_PREINIT
+
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 1 drive per IDE bus */
+
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
+#define CONFIG_SYS_ATA_BASE_ADDR MPC512X_PATA
+
+/* Offset for data I/O RefMan MPC5121EE Table 28-10 */
+#define CONFIG_SYS_ATA_DATA_OFFSET (0x00A0)
+
+/* Offset for normal register accesses */
+#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
+
+/* Offset for alternate registers RefMan MPC5121EE Table 28-23 */
+#define CONFIG_SYS_ATA_ALT_OFFSET (0x00D8)
+
+/* Interval between registers */
+#define CONFIG_SYS_ATA_STRIDE 4
+
+#define ATA_BASE_ADDR MPC512X_PATA
+
+/*
+ * Control register bit definitions
+ */
+#define FSL_ATA_CTRL_FIFO_RST_B 0x80000000
+#define FSL_ATA_CTRL_ATA_RST_B 0x40000000
+#define FSL_ATA_CTRL_FIFO_TX_EN 0x20000000
+#define FSL_ATA_CTRL_FIFO_RCV_EN 0x10000000
+#define FSL_ATA_CTRL_DMA_PENDING 0x08000000
+#define FSL_ATA_CTRL_DMA_ULTRA 0x04000000
+#define FSL_ATA_CTRL_DMA_WRITE 0x02000000
+#define FSL_ATA_CTRL_IORDY_EN 0x01000000
+
#endif /* __CONFIG_H */
/* Register Offset Base */
#define MPC512X_FEC (CONFIG_SYS_IMMR + 0x02800)
+#define MPC512X_PATA (CONFIG_SYS_IMMR + 0x10200)
/* IIM control */
#define IIM_SET_UA(bk, f) ((bk << 3) | (f >> 5))
projects / u-boot / commitdiff