# SPDX-License-Identifier: GPL-2.0+
#
-obj-y += timer.o clock.o soc.o
+obj-y += timer.o soc.o
+++ /dev/null
-/*
- * (C) Copyright 2016
- * Vikas Manocha, <vikas.manocha@st.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/rcc.h>
-#include <asm/arch/stm32.h>
-#include <asm/arch/stm32_periph.h>
-
-#define RCC_CR_HSION BIT(0)
-#define RCC_CR_HSEON BIT(16)
-#define RCC_CR_HSERDY BIT(17)
-#define RCC_CR_HSEBYP BIT(18)
-#define RCC_CR_CSSON BIT(19)
-#define RCC_CR_PLLON BIT(24)
-#define RCC_CR_PLLRDY BIT(25)
-
-#define RCC_PLLCFGR_PLLM_MASK GENMASK(5, 0)
-#define RCC_PLLCFGR_PLLN_MASK GENMASK(14, 6)
-#define RCC_PLLCFGR_PLLP_MASK GENMASK(17, 16)
-#define RCC_PLLCFGR_PLLQ_MASK GENMASK(27, 24)
-#define RCC_PLLCFGR_PLLSRC BIT(22)
-#define RCC_PLLCFGR_PLLM_SHIFT 0
-#define RCC_PLLCFGR_PLLN_SHIFT 6
-#define RCC_PLLCFGR_PLLP_SHIFT 16
-#define RCC_PLLCFGR_PLLQ_SHIFT 24
-
-#define RCC_CFGR_AHB_PSC_MASK GENMASK(7, 4)
-#define RCC_CFGR_APB1_PSC_MASK GENMASK(12, 10)
-#define RCC_CFGR_APB2_PSC_MASK GENMASK(15, 13)
-#define RCC_CFGR_SW0 BIT(0)
-#define RCC_CFGR_SW1 BIT(1)
-#define RCC_CFGR_SW_MASK GENMASK(1, 0)
-#define RCC_CFGR_SW_HSI 0
-#define RCC_CFGR_SW_HSE RCC_CFGR_SW0
-#define RCC_CFGR_SW_PLL RCC_CFGR_SW1
-#define RCC_CFGR_SWS0 BIT(2)
-#define RCC_CFGR_SWS1 BIT(3)
-#define RCC_CFGR_SWS_MASK GENMASK(3, 2)
-#define RCC_CFGR_SWS_HSI 0
-#define RCC_CFGR_SWS_HSE RCC_CFGR_SWS0
-#define RCC_CFGR_SWS_PLL RCC_CFGR_SWS1
-#define RCC_CFGR_HPRE_SHIFT 4
-#define RCC_CFGR_PPRE1_SHIFT 10
-#define RCC_CFGR_PPRE2_SHIFT 13
-
-/*
- * Offsets of some PWR registers
- */
-#define PWR_CR1_ODEN BIT(16)
-#define PWR_CR1_ODSWEN BIT(17)
-#define PWR_CSR1_ODRDY BIT(16)
-#define PWR_CSR1_ODSWRDY BIT(17)
-
-struct pll_psc {
- u8 pll_m;
- u16 pll_n;
- u8 pll_p;
- u8 pll_q;
- u8 ahb_psc;
- u8 apb1_psc;
- u8 apb2_psc;
-};
-
-#define AHB_PSC_1 0
-#define AHB_PSC_2 0x8
-#define AHB_PSC_4 0x9
-#define AHB_PSC_8 0xA
-#define AHB_PSC_16 0xB
-#define AHB_PSC_64 0xC
-#define AHB_PSC_128 0xD
-#define AHB_PSC_256 0xE
-#define AHB_PSC_512 0xF
-
-#define APB_PSC_1 0
-#define APB_PSC_2 0x4
-#define APB_PSC_4 0x5
-#define APB_PSC_8 0x6
-#define APB_PSC_16 0x7
-
-#if !defined(CONFIG_STM32_HSE_HZ)
-#error "CONFIG_STM32_HSE_HZ not defined!"
-#else
-#if (CONFIG_STM32_HSE_HZ == 25000000)
-#if (CONFIG_SYS_CLK_FREQ == 200000000)
-/* 200 MHz */
-struct pll_psc sys_pll_psc = {
- .pll_m = 25,
- .pll_n = 400,
- .pll_p = 2,
- .pll_q = 8,
- .ahb_psc = AHB_PSC_1,
- .apb1_psc = APB_PSC_4,
- .apb2_psc = APB_PSC_2
-};
-#endif
-#else
-#error "No PLL/Prescaler configuration for given CONFIG_STM32_HSE_HZ exists"
-#endif
-#endif
-
-int configure_clocks(void)
-{
- /* Reset RCC configuration */
- setbits_le32(&STM32_RCC->cr, RCC_CR_HSION);
- writel(0, &STM32_RCC->cfgr); /* Reset CFGR */
- clrbits_le32(&STM32_RCC->cr, (RCC_CR_HSEON | RCC_CR_CSSON
- | RCC_CR_PLLON));
- writel(0x24003010, &STM32_RCC->pllcfgr); /* Reset value from RM */
- clrbits_le32(&STM32_RCC->cr, RCC_CR_HSEBYP);
- writel(0, &STM32_RCC->cir); /* Disable all interrupts */
-
- /* Configure for HSE+PLL operation */
- setbits_le32(&STM32_RCC->cr, RCC_CR_HSEON);
- while (!(readl(&STM32_RCC->cr) & RCC_CR_HSERDY))
- ;
-
- setbits_le32(&STM32_RCC->cfgr, ((
- sys_pll_psc.ahb_psc << RCC_CFGR_HPRE_SHIFT)
- | (sys_pll_psc.apb1_psc << RCC_CFGR_PPRE1_SHIFT)
- | (sys_pll_psc.apb2_psc << RCC_CFGR_PPRE2_SHIFT)));
-
- /* Configure the main PLL */
- uint32_t pllcfgr = 0;
- pllcfgr = RCC_PLLCFGR_PLLSRC; /* pll source HSE */
- pllcfgr |= sys_pll_psc.pll_m << RCC_PLLCFGR_PLLM_SHIFT;
- pllcfgr |= sys_pll_psc.pll_n << RCC_PLLCFGR_PLLN_SHIFT;
- pllcfgr |= ((sys_pll_psc.pll_p >> 1) - 1) << RCC_PLLCFGR_PLLP_SHIFT;
- pllcfgr |= sys_pll_psc.pll_q << RCC_PLLCFGR_PLLQ_SHIFT;
- writel(pllcfgr, &STM32_RCC->pllcfgr);
-
- /* Enable the main PLL */
- setbits_le32(&STM32_RCC->cr, RCC_CR_PLLON);
- while (!(readl(&STM32_RCC->cr) & RCC_CR_PLLRDY))
- ;
-
- /* Enable high performance mode, System frequency up to 200 MHz */
- setbits_le32(&STM32_RCC->apb1enr, RCC_APB1ENR_PWREN);
- setbits_le32(&STM32_PWR->cr1, PWR_CR1_ODEN);
- /* Infinite wait! */
- while (!(readl(&STM32_PWR->csr1) & PWR_CSR1_ODRDY))
- ;
- /* Enable the Over-drive switch */
- setbits_le32(&STM32_PWR->cr1, PWR_CR1_ODSWEN);
- /* Infinite wait! */
- while (!(readl(&STM32_PWR->csr1) & PWR_CSR1_ODSWRDY))
- ;
-
- stm32_flash_latency_cfg(5);
- clrbits_le32(&STM32_RCC->cfgr, (RCC_CFGR_SW0 | RCC_CFGR_SW1));
- setbits_le32(&STM32_RCC->cfgr, RCC_CFGR_SW_PLL);
-
- while ((readl(&STM32_RCC->cfgr) & RCC_CFGR_SWS_MASK) !=
- RCC_CFGR_SWS_PLL)
- ;
-
- return 0;
-}
-
-unsigned long clock_get(enum clock clck)
-{
- u32 sysclk = 0;
- u32 shift = 0;
- /* Prescaler table lookups for clock computation */
- u8 ahb_psc_table[16] = {
- 0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9
- };
- u8 apb_psc_table[8] = {
- 0, 0, 0, 0, 1, 2, 3, 4
- };
-
- if ((readl(&STM32_RCC->cfgr) & RCC_CFGR_SWS_MASK) ==
- RCC_CFGR_SWS_PLL) {
- u16 pllm, plln, pllp;
- pllm = (readl(&STM32_RCC->pllcfgr) & RCC_PLLCFGR_PLLM_MASK);
- plln = ((readl(&STM32_RCC->pllcfgr) & RCC_PLLCFGR_PLLN_MASK)
- >> RCC_PLLCFGR_PLLN_SHIFT);
- pllp = ((((readl(&STM32_RCC->pllcfgr) & RCC_PLLCFGR_PLLP_MASK)
- >> RCC_PLLCFGR_PLLP_SHIFT) + 1) << 1);
- sysclk = ((CONFIG_STM32_HSE_HZ / pllm) * plln) / pllp;
- }
-
- switch (clck) {
- case CLOCK_CORE:
- return sysclk;
- break;
- case CLOCK_AHB:
- shift = ahb_psc_table[(
- (readl(&STM32_RCC->cfgr) & RCC_CFGR_AHB_PSC_MASK)
- >> RCC_CFGR_HPRE_SHIFT)];
- return sysclk >>= shift;
- break;
- case CLOCK_APB1:
- shift = apb_psc_table[(
- (readl(&STM32_RCC->cfgr) & RCC_CFGR_APB1_PSC_MASK)
- >> RCC_CFGR_PPRE1_SHIFT)];
- return sysclk >>= shift;
- break;
- case CLOCK_APB2:
- shift = apb_psc_table[(
- (readl(&STM32_RCC->cfgr) & RCC_CFGR_APB2_PSC_MASK)
- >> RCC_CFGR_PPRE2_SHIFT)];
- return sysclk >>= shift;
- break;
- default:
- return 0;
- break;
- }
-}
-
-
-void clock_setup(int peripheral)
-{
- switch (peripheral) {
- case USART1_CLOCK_CFG:
- setbits_le32(&STM32_RCC->apb2enr, RCC_APB2ENR_USART1EN);
- break;
- case GPIO_A_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_A_EN);
- break;
- case GPIO_B_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_B_EN);
- break;
- case GPIO_C_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_C_EN);
- break;
- case GPIO_D_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_D_EN);
- break;
- case GPIO_E_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_E_EN);
- break;
- case GPIO_F_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_F_EN);
- break;
- case GPIO_G_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_G_EN);
- break;
- case GPIO_H_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_H_EN);
- break;
- case GPIO_I_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_I_EN);
- break;
- case GPIO_J_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_J_EN);
- break;
- case GPIO_K_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_K_EN);
- break;
- case SYSCFG_CLOCK_CFG:
- setbits_le32(&STM32_RCC->apb2enr, RCC_APB2ENR_SYSCFGEN);
- break;
- case TIMER2_CLOCK_CFG:
- setbits_le32(&STM32_RCC->apb1enr, RCC_APB1ENR_TIM2EN);
- break;
- case FMC_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb3enr, RCC_AHB3ENR_FMC_EN);
- break;
- case STMMAC_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_ETHMAC_EN);
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_ETHMAC_RX_EN);
- setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_ETHMAC_TX_EN);
- break;
- case QSPI_CLOCK_CFG:
- setbits_le32(&STM32_RCC->ahb3enr, RCC_AHB3ENR_QSPI_EN);
- break;
- default:
- break;
- }
-}
int arch_cpu_init(void)
{
- configure_clocks();
-
/*
* Configure the memory protection unit (MPU)
* 0x00000000 - 0xffffffff: Strong-order, Shareable
CONFIG_STM32_QSPI=y
CONFIG_OF_LIBFDT_OVERLAY=y
# CONFIG_EFI_LOADER is not set
+CONFIG_CLK=y
--- /dev/null
+STMicroelectronics STM32 Reset and Clock Controller
+===================================================
+
+The RCC IP is both a reset and a clock controller.
+
+Please refer to clock-bindings.txt for common clock controller binding usage.
+Please also refer to reset.txt for common reset controller binding usage.
+
+Required properties:
+- compatible: Should be:
+ "st,stm32f42xx-rcc"
+ "st,stm32f469-rcc"
+- reg: should be register base and length as documented in the
+ datasheet
+- #reset-cells: 1, see below
+- #clock-cells: 2, device nodes should specify the clock in their "clocks"
+ property, containing a phandle to the clock device node, an index selecting
+ between gated clocks and other clocks and an index specifying the clock to
+ use.
+
+Example:
+
+ rcc: rcc@40023800 {
+ #reset-cells = <1>;
+ #clock-cells = <2>
+ compatible = "st,stm32f42xx-rcc", "st,stm32-rcc";
+ reg = <0x40023800 0x400>;
+ };
+
+Specifying gated clocks
+=======================
+
+The primary index must be set to 0.
+
+The secondary index is the bit number within the RCC register bank, starting
+from the first RCC clock enable register (RCC_AHB1ENR, address offset 0x30).
+
+It is calculated as: index = register_offset / 4 * 32 + bit_offset.
+Where bit_offset is the bit offset within the register (LSB is 0, MSB is 31).
+
+To simplify the usage and to share bit definition with the reset and clock
+drivers of the RCC IP, macros are available to generate the index in
+human-readble format.
+
+For STM32F4 series, the macro are available here:
+ - include/dt-bindings/mfd/stm32f4-rcc.h
+
+Example:
+
+ /* Gated clock, AHB1 bit 0 (GPIOA) */
+ ... {
+ clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOA)>
+ };
+
+ /* Gated clock, AHB2 bit 4 (CRYP) */
+ ... {
+ clocks = <&rcc 0 STM32F4_AHB2_CLOCK(CRYP)>
+ };
+
+Specifying other clocks
+=======================
+
+The primary index must be set to 1.
+
+The secondary index is bound with the following magic numbers:
+
+ 0 SYSTICK
+ 1 FCLK
+
+Example:
+
+ /* Misc clock, FCLK */
+ ... {
+ clocks = <&rcc 1 STM32F4_APB1_CLOCK(TIM2)>
+ };
+
+
+Specifying softreset control of devices
+=======================================
+
+Device nodes should specify the reset channel required in their "resets"
+property, containing a phandle to the reset device node and an index specifying
+which channel to use.
+The index is the bit number within the RCC registers bank, starting from RCC
+base address.
+It is calculated as: index = register_offset / 4 * 32 + bit_offset.
+Where bit_offset is the bit offset within the register.
+For example, for CRC reset:
+ crc = AHB1RSTR_offset / 4 * 32 + CRCRST_bit_offset = 0x10 / 4 * 32 + 12 = 140
+
+example:
+
+ timer2 {
+ resets = <&rcc STM32F4_APB1_RESET(TIM2)>;
+ };
obj-$(CONFIG_CLK_EXYNOS) += exynos/
obj-$(CONFIG_CLK_AT91) += at91/
obj-$(CONFIG_CLK_BOSTON) += clk_boston.o
-
obj-$(CONFIG_ARCH_ASPEED) += aspeed/
+obj-$(CONFIG_STM32F7) += clk_stm32f7.o
--- /dev/null
+/*
+ * (C) Copyright 2017
+ * Vikas Manocha, <vikas.manocha@st.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#include <common.h>
+#include <clk-uclass.h>
+#include <dm.h>
+#include <asm/io.h>
+#include <asm/arch/rcc.h>
+#include <asm/arch/stm32.h>
+#include <asm/arch/stm32_periph.h>
+
+#define RCC_CR_HSION BIT(0)
+#define RCC_CR_HSEON BIT(16)
+#define RCC_CR_HSERDY BIT(17)
+#define RCC_CR_HSEBYP BIT(18)
+#define RCC_CR_CSSON BIT(19)
+#define RCC_CR_PLLON BIT(24)
+#define RCC_CR_PLLRDY BIT(25)
+
+#define RCC_PLLCFGR_PLLM_MASK GENMASK(5, 0)
+#define RCC_PLLCFGR_PLLN_MASK GENMASK(14, 6)
+#define RCC_PLLCFGR_PLLP_MASK GENMASK(17, 16)
+#define RCC_PLLCFGR_PLLQ_MASK GENMASK(27, 24)
+#define RCC_PLLCFGR_PLLSRC BIT(22)
+#define RCC_PLLCFGR_PLLM_SHIFT 0
+#define RCC_PLLCFGR_PLLN_SHIFT 6
+#define RCC_PLLCFGR_PLLP_SHIFT 16
+#define RCC_PLLCFGR_PLLQ_SHIFT 24
+
+#define RCC_CFGR_AHB_PSC_MASK GENMASK(7, 4)
+#define RCC_CFGR_APB1_PSC_MASK GENMASK(12, 10)
+#define RCC_CFGR_APB2_PSC_MASK GENMASK(15, 13)
+#define RCC_CFGR_SW0 BIT(0)
+#define RCC_CFGR_SW1 BIT(1)
+#define RCC_CFGR_SW_MASK GENMASK(1, 0)
+#define RCC_CFGR_SW_HSI 0
+#define RCC_CFGR_SW_HSE RCC_CFGR_SW0
+#define RCC_CFGR_SW_PLL RCC_CFGR_SW1
+#define RCC_CFGR_SWS0 BIT(2)
+#define RCC_CFGR_SWS1 BIT(3)
+#define RCC_CFGR_SWS_MASK GENMASK(3, 2)
+#define RCC_CFGR_SWS_HSI 0
+#define RCC_CFGR_SWS_HSE RCC_CFGR_SWS0
+#define RCC_CFGR_SWS_PLL RCC_CFGR_SWS1
+#define RCC_CFGR_HPRE_SHIFT 4
+#define RCC_CFGR_PPRE1_SHIFT 10
+#define RCC_CFGR_PPRE2_SHIFT 13
+
+/*
+ * Offsets of some PWR registers
+ */
+#define PWR_CR1_ODEN BIT(16)
+#define PWR_CR1_ODSWEN BIT(17)
+#define PWR_CSR1_ODRDY BIT(16)
+#define PWR_CSR1_ODSWRDY BIT(17)
+
+struct pll_psc {
+ u8 pll_m;
+ u16 pll_n;
+ u8 pll_p;
+ u8 pll_q;
+ u8 ahb_psc;
+ u8 apb1_psc;
+ u8 apb2_psc;
+};
+
+#define AHB_PSC_1 0
+#define AHB_PSC_2 0x8
+#define AHB_PSC_4 0x9
+#define AHB_PSC_8 0xA
+#define AHB_PSC_16 0xB
+#define AHB_PSC_64 0xC
+#define AHB_PSC_128 0xD
+#define AHB_PSC_256 0xE
+#define AHB_PSC_512 0xF
+
+#define APB_PSC_1 0
+#define APB_PSC_2 0x4
+#define APB_PSC_4 0x5
+#define APB_PSC_8 0x6
+#define APB_PSC_16 0x7
+
+#if !defined(CONFIG_STM32_HSE_HZ)
+#error "CONFIG_STM32_HSE_HZ not defined!"
+#else
+#if (CONFIG_STM32_HSE_HZ == 25000000)
+#if (CONFIG_SYS_CLK_FREQ == 200000000)
+/* 200 MHz */
+struct pll_psc sys_pll_psc = {
+ .pll_m = 25,
+ .pll_n = 400,
+ .pll_p = 2,
+ .pll_q = 8,
+ .ahb_psc = AHB_PSC_1,
+ .apb1_psc = APB_PSC_4,
+ .apb2_psc = APB_PSC_2
+};
+#endif
+#else
+#error "No PLL/Prescaler configuration for given CONFIG_STM32_HSE_HZ exists"
+#endif
+#endif
+
+int configure_clocks(void)
+{
+ /* Reset RCC configuration */
+ setbits_le32(&STM32_RCC->cr, RCC_CR_HSION);
+ writel(0, &STM32_RCC->cfgr); /* Reset CFGR */
+ clrbits_le32(&STM32_RCC->cr, (RCC_CR_HSEON | RCC_CR_CSSON
+ | RCC_CR_PLLON));
+ writel(0x24003010, &STM32_RCC->pllcfgr); /* Reset value from RM */
+ clrbits_le32(&STM32_RCC->cr, RCC_CR_HSEBYP);
+ writel(0, &STM32_RCC->cir); /* Disable all interrupts */
+
+ /* Configure for HSE+PLL operation */
+ setbits_le32(&STM32_RCC->cr, RCC_CR_HSEON);
+ while (!(readl(&STM32_RCC->cr) & RCC_CR_HSERDY))
+ ;
+
+ setbits_le32(&STM32_RCC->cfgr, ((
+ sys_pll_psc.ahb_psc << RCC_CFGR_HPRE_SHIFT)
+ | (sys_pll_psc.apb1_psc << RCC_CFGR_PPRE1_SHIFT)
+ | (sys_pll_psc.apb2_psc << RCC_CFGR_PPRE2_SHIFT)));
+
+ /* Configure the main PLL */
+ uint32_t pllcfgr = 0;
+ pllcfgr = RCC_PLLCFGR_PLLSRC; /* pll source HSE */
+ pllcfgr |= sys_pll_psc.pll_m << RCC_PLLCFGR_PLLM_SHIFT;
+ pllcfgr |= sys_pll_psc.pll_n << RCC_PLLCFGR_PLLN_SHIFT;
+ pllcfgr |= ((sys_pll_psc.pll_p >> 1) - 1) << RCC_PLLCFGR_PLLP_SHIFT;
+ pllcfgr |= sys_pll_psc.pll_q << RCC_PLLCFGR_PLLQ_SHIFT;
+ writel(pllcfgr, &STM32_RCC->pllcfgr);
+
+ /* Enable the main PLL */
+ setbits_le32(&STM32_RCC->cr, RCC_CR_PLLON);
+ while (!(readl(&STM32_RCC->cr) & RCC_CR_PLLRDY))
+ ;
+
+ /* Enable high performance mode, System frequency up to 200 MHz */
+ setbits_le32(&STM32_RCC->apb1enr, RCC_APB1ENR_PWREN);
+ setbits_le32(&STM32_PWR->cr1, PWR_CR1_ODEN);
+ /* Infinite wait! */
+ while (!(readl(&STM32_PWR->csr1) & PWR_CSR1_ODRDY))
+ ;
+ /* Enable the Over-drive switch */
+ setbits_le32(&STM32_PWR->cr1, PWR_CR1_ODSWEN);
+ /* Infinite wait! */
+ while (!(readl(&STM32_PWR->csr1) & PWR_CSR1_ODSWRDY))
+ ;
+
+ stm32_flash_latency_cfg(5);
+ clrbits_le32(&STM32_RCC->cfgr, (RCC_CFGR_SW0 | RCC_CFGR_SW1));
+ setbits_le32(&STM32_RCC->cfgr, RCC_CFGR_SW_PLL);
+
+ while ((readl(&STM32_RCC->cfgr) & RCC_CFGR_SWS_MASK) !=
+ RCC_CFGR_SWS_PLL)
+ ;
+
+ return 0;
+}
+
+unsigned long clock_get(enum clock clck)
+{
+ u32 sysclk = 0;
+ u32 shift = 0;
+ /* Prescaler table lookups for clock computation */
+ u8 ahb_psc_table[16] = {
+ 0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9
+ };
+ u8 apb_psc_table[8] = {
+ 0, 0, 0, 0, 1, 2, 3, 4
+ };
+
+ if ((readl(&STM32_RCC->cfgr) & RCC_CFGR_SWS_MASK) ==
+ RCC_CFGR_SWS_PLL) {
+ u16 pllm, plln, pllp;
+ pllm = (readl(&STM32_RCC->pllcfgr) & RCC_PLLCFGR_PLLM_MASK);
+ plln = ((readl(&STM32_RCC->pllcfgr) & RCC_PLLCFGR_PLLN_MASK)
+ >> RCC_PLLCFGR_PLLN_SHIFT);
+ pllp = ((((readl(&STM32_RCC->pllcfgr) & RCC_PLLCFGR_PLLP_MASK)
+ >> RCC_PLLCFGR_PLLP_SHIFT) + 1) << 1);
+ sysclk = ((CONFIG_STM32_HSE_HZ / pllm) * plln) / pllp;
+ }
+
+ switch (clck) {
+ case CLOCK_CORE:
+ return sysclk;
+ break;
+ case CLOCK_AHB:
+ shift = ahb_psc_table[(
+ (readl(&STM32_RCC->cfgr) & RCC_CFGR_AHB_PSC_MASK)
+ >> RCC_CFGR_HPRE_SHIFT)];
+ return sysclk >>= shift;
+ break;
+ case CLOCK_APB1:
+ shift = apb_psc_table[(
+ (readl(&STM32_RCC->cfgr) & RCC_CFGR_APB1_PSC_MASK)
+ >> RCC_CFGR_PPRE1_SHIFT)];
+ return sysclk >>= shift;
+ break;
+ case CLOCK_APB2:
+ shift = apb_psc_table[(
+ (readl(&STM32_RCC->cfgr) & RCC_CFGR_APB2_PSC_MASK)
+ >> RCC_CFGR_PPRE2_SHIFT)];
+ return sysclk >>= shift;
+ break;
+ default:
+ return 0;
+ break;
+ }
+}
+
+static int stm32_clk_enable(struct clk *clk)
+{
+ u32 offset = clk->id / 32;
+ u32 bit_index = clk->id % 32;
+
+ debug("%s: clkid = %ld, offset from AHB1ENR is %d, bit_index = %d\n",
+ __func__, clk->id, offset, bit_index);
+ setbits_le32(&STM32_RCC->ahb1enr + offset, BIT(bit_index));
+
+ return 0;
+}
+
+void clock_setup(int peripheral)
+{
+ switch (peripheral) {
+ case USART1_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->apb2enr, RCC_APB2ENR_USART1EN);
+ break;
+ case GPIO_A_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_A_EN);
+ break;
+ case GPIO_B_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_B_EN);
+ break;
+ case GPIO_C_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_C_EN);
+ break;
+ case GPIO_D_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_D_EN);
+ break;
+ case GPIO_E_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_E_EN);
+ break;
+ case GPIO_F_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_F_EN);
+ break;
+ case GPIO_G_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_G_EN);
+ break;
+ case GPIO_H_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_H_EN);
+ break;
+ case GPIO_I_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_I_EN);
+ break;
+ case GPIO_J_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_J_EN);
+ break;
+ case GPIO_K_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_GPIO_K_EN);
+ break;
+ case SYSCFG_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->apb2enr, RCC_APB2ENR_SYSCFGEN);
+ break;
+ case TIMER2_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->apb1enr, RCC_APB1ENR_TIM2EN);
+ break;
+ case FMC_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb3enr, RCC_AHB3ENR_FMC_EN);
+ break;
+ case STMMAC_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_ETHMAC_EN);
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_ETHMAC_RX_EN);
+ setbits_le32(&STM32_RCC->ahb1enr, RCC_AHB1ENR_ETHMAC_TX_EN);
+ break;
+ case QSPI_CLOCK_CFG:
+ setbits_le32(&STM32_RCC->ahb3enr, RCC_AHB3ENR_QSPI_EN);
+ break;
+ default:
+ break;
+ }
+}
+
+static int stm32_clk_probe(struct udevice *dev)
+{
+ debug("%s: stm32_clk_probe\n", __func__);
+ configure_clocks();
+
+ return 0;
+}
+
+static int stm32_clk_of_xlate(struct clk *clk,
+ struct fdtdec_phandle_args *args)
+{
+ debug("%s(clk=%p)\n", __func__, clk);
+
+ if (args->args_count != 2) {
+ debug("Invaild args_count: %d\n", args->args_count);
+ return -EINVAL;
+ }
+
+ if (args->args_count)
+ clk->id = args->args[1];
+ else
+ clk->id = 0;
+
+ return 0;
+}
+
+static struct clk_ops stm32_clk_ops = {
+ .of_xlate = stm32_clk_of_xlate,
+ .enable = stm32_clk_enable,
+};
+
+static const struct udevice_id stm32_clk_ids[] = {
+ { .compatible = "st,stm32f42xx-rcc"},
+ {}
+};
+
+U_BOOT_DRIVER(stm32f7_clk) = {
+ .name = "stm32f7_clk",
+ .id = UCLASS_CLK,
+ .of_match = stm32_clk_ids,
+ .ops = &stm32_clk_ops,
+ .probe = stm32_clk_probe,
+ .flags = DM_FLAG_PRE_RELOC,
+};
projects / u-boot / commitdiff