This board is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
config TARGET_RRVISION
bool "Support RRvision"
-config TARGET_SPD823TS
- bool "Support SPD823TS"
-
config TARGET_TQM823L
bool "Support TQM823L"
source "board/lwmon/Kconfig"
source "board/netvia/Kconfig"
source "board/r360mpi/Kconfig"
-source "board/spd8xx/Kconfig"
source "board/tqc/tqm8xx/Kconfig"
endmenu
defined(CONFIG_IVMS8) || \
defined(CONFIG_LWMON) || \
defined(CONFIG_R360MPI) || \
- defined(CONFIG_RMU) || \
- defined(CONFIG_SPD823TS)
+ defined(CONFIG_RMU)
memctl->memc_br0 = CONFIG_SYS_BR0_PRELIM;
#endif
+++ /dev/null
-if TARGET_SPD823TS
-
-config SYS_BOARD
- default "spd8xx"
-
-config SYS_CONFIG_NAME
- default "SPD823TS"
-
-endif
+++ /dev/null
-SPD8XX BOARD
-M: Wolfgang Denk <wd@denx.de>
-S: Maintained
-F: board/spd8xx/
-F: include/configs/SPD823TS.h
-F: configs/SPD823TS_defconfig
+++ /dev/null
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = spd8xx.o flash.o
+++ /dev/null
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
- /* All Speech Design board memory (DRAM and EPROM) initialisation is
- done in dram_init().
- The caller of ths function here expects the total size and will hang,
- if we give here back 0. So we return the EPROM size. */
-
- return (1024 * 1024); /* 1 MB */
-}
-
-/*-----------------------------------------------------------------------
- */
-
-void flash_print_info (flash_info_t *info)
-{
- printf("no FLASH memory in MPC823TS board\n");
- return;
-}
-
-int flash_erase (flash_info_t *info, int s_first, int s_last)
-{
- return 1;
-}
-
-/*-----------------------------------------------------------------------
- */
+++ /dev/null
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- * Ulrich Lutz, Speech Design GmbH, ulutz@datalab.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc8xx.h>
-#include <commproc.h>
-
-/* ------------------------------------------------------------------------- */
-
-static long int dram_size (long int, long int *, long int);
-
-/* ------------------------------------------------------------------------- */
-
-#define _NOT_USED_ 0xFFFFFFFF
-
-const uint sharc_table[] = {
- /*
- * Single Read. (Offset 0 in UPM RAM)
- */
- 0x0FF3FC04, 0x0FF3EC00, 0x7FFFEC04, 0xFFFFEC04,
- 0xFFFFEC05, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Burst Read. (Offset 8 in UPM RAM)
- */
- /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Single Write. (Offset 18 in UPM RAM)
- */
- 0x0FAFFC04, 0x0FAFEC00, 0x7FFFEC04, 0xFFFFEC04,
- 0xFFFFEC05, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Burst Write. (Offset 20 in UPM RAM)
- */
- /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Refresh (Offset 30 in UPM RAM)
- */
- /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Exception. (Offset 3c in UPM RAM)
- */
- 0x7FFFFC07, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_,
-};
-
-
-const uint sdram_table[] = {
- /*
- * Single Read. (Offset 0 in UPM RAM)
- */
- 0x1F07FC04, 0xEEAEFC04, 0x11ADFC04, 0xEFBBBC00,
- 0x1FF77C47, /* last */
- /*
- * SDRAM Initialization (offset 5 in UPM RAM)
- *
- * This is no UPM entry point. The following definition uses
- * the remaining space to establish an initialization
- * sequence, which is executed by a RUN command.
- *
- */
- 0x1FF77C35, 0xEFEABC34, 0x1FB57C35, /* last */
- /*
- * Burst Read. (Offset 8 in UPM RAM)
- */
- 0x1F07FC04, 0xEEAEFC04, 0x10ADFC04, 0xF0AFFC00,
- 0xF0AFFC00, 0xF1AFFC00, 0xEFBBBC00, 0x1FF77C47, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Single Write. (Offset 18 in UPM RAM)
- */
- 0x1F27FC04, 0xEEAEBC00, 0x01B93C04, 0x1FF77C47, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Burst Write. (Offset 20 in UPM RAM)
- */
- 0x1F07FC04, 0xEEAEBC00, 0x10AD7C00, 0xF0AFFC00,
- 0xF0AFFC00, 0xE1BBBC04, 0x1FF77C47, /* last */
- _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Refresh (Offset 30 in UPM RAM)
- */
- 0x1FF5FC84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
- 0xFFFFFC84, 0xFFFFFC07, /* last */
- _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Exception. (Offset 3c in UPM RAM)
- */
- 0x7FFFFC07, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_,
-};
-
-/* ------------------------------------------------------------------------- */
-
-
-/*
- * Check Board Identity:
- *
- */
-
-int checkboard (void)
-{
- puts ("Board: SPD823TS\n");
- return (0);
-}
-
-/* ------------------------------------------------------------------------- */
-
-phys_size_t initdram (int board_type)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- long int size_b0;
-
-#if 0
- /*
- * Map controller bank 2 to the SRAM bank at preliminary address.
- */
- memctl->memc_or2 = CONFIG_SYS_OR2;
- memctl->memc_br2 = CONFIG_SYS_BR2;
-#endif
-
- /*
- * Map controller bank 4 to the PER8 bank.
- */
- memctl->memc_or4 = CONFIG_SYS_OR4;
- memctl->memc_br4 = CONFIG_SYS_BR4;
-
-#if 0
- /* Configure SHARC at UMA */
- upmconfig (UPMA, (uint *) sharc_table,
- sizeof (sharc_table) / sizeof (uint));
- /* Map controller bank 5 to the SHARC */
- memctl->memc_or5 = CONFIG_SYS_OR5;
- memctl->memc_br5 = CONFIG_SYS_BR5;
-#endif
-
- memctl->memc_mamr = 0x00001000;
-
- /* Configure SDRAM at UMB */
- upmconfig (UPMB, (uint *) sdram_table,
- sizeof (sdram_table) / sizeof (uint));
-
- memctl->memc_mptpr = CONFIG_SYS_MPTPR_1BK_8K;
-
- memctl->memc_mar = 0x00000088;
-
- /*
- * Map controller bank 3 to the SDRAM bank at preliminary address.
- */
- memctl->memc_or3 = CONFIG_SYS_OR3_PRELIM;
- memctl->memc_br3 = CONFIG_SYS_BR3_PRELIM;
-
- memctl->memc_mbmr = CONFIG_SYS_MBMR_8COL; /* refresh not enabled yet */
-
- udelay (200);
- memctl->memc_mcr = 0x80806105;
- udelay (1);
- memctl->memc_mcr = 0x80806130;
- udelay (1);
- memctl->memc_mcr = 0x80806130;
- udelay (1);
- memctl->memc_mcr = 0x80806106;
-
- memctl->memc_mbmr |= MBMR_PTBE; /* refresh enabled */
-
- /*
- * Check Bank 0 Memory Size for re-configuration
- */
- size_b0 =
- dram_size (CONFIG_SYS_MBMR_8COL, SDRAM_BASE3_PRELIM,
- SDRAM_MAX_SIZE);
-
- memctl->memc_mbmr = CONFIG_SYS_MBMR_8COL | MBMR_PTBE;
-
- return (size_b0);
-}
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * Check memory range for valid RAM. A simple memory test determines
- * the actually available RAM size between addresses `base' and
- * `base + maxsize'. Some (not all) hardware errors are detected:
- * - short between address lines
- * - short between data lines
- */
-
-static long int dram_size (long int mamr_value, long int *base,
- long int maxsize)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
-
- memctl->memc_mbmr = mamr_value;
-
- return (get_ram_size (base, maxsize));
-}
-
-/* ------------------------------------------------------------------------- */
-
-void reset_phy (void)
-{
- immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- ushort sreg;
-
- /* Configure extra port pins for NS DP83843 PHY */
- immr->im_ioport.iop_papar &= ~(PA_ENET_MDC | PA_ENET_MDIO);
-
- sreg = immr->im_ioport.iop_padir;
- sreg |= PA_ENET_MDC; /* Mgmt. Data Clock is Output */
- sreg &= ~(PA_ENET_MDIO); /* Mgmt. Data I/O is bidirect. => Input */
- immr->im_ioport.iop_padir = sreg;
-
- immr->im_ioport.iop_padat &= ~(PA_ENET_MDC); /* set MDC = 0 */
-
- /*
- * RESET in implemented by a positive pulse of at least 1 us
- * at the reset pin.
- *
- * Configure RESET pins for NS DP83843 PHY, and RESET chip.
- *
- * Note: The RESET pin is high active, but there is an
- * inverter on the SPD823TS board...
- */
- immr->im_ioport.iop_pcpar &= ~(PC_ENET_RESET);
- immr->im_ioport.iop_pcdir |= PC_ENET_RESET;
- /* assert RESET signal of PHY */
- immr->im_ioport.iop_pcdat &= ~(PC_ENET_RESET);
- udelay (10);
- /* de-assert RESET signal of PHY */
- immr->im_ioport.iop_pcdat |= PC_ENET_RESET;
- udelay (10);
-}
-
-/* ------------------------------------------------------------------------- */
-
-void ide_set_reset (int on)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
-
- /*
- * Configure PC for IDE Reset Pin
- */
- if (on) { /* assert RESET */
- immr->im_ioport.iop_pcdat &= ~(CONFIG_SYS_PC_IDE_RESET);
- } else { /* release RESET */
- immr->im_ioport.iop_pcdat |= CONFIG_SYS_PC_IDE_RESET;
- }
-
- /* program port pin as GPIO output */
- immr->im_ioport.iop_pcpar &= ~(CONFIG_SYS_PC_IDE_RESET);
- immr->im_ioport.iop_pcso &= ~(CONFIG_SYS_PC_IDE_RESET);
- immr->im_ioport.iop_pcdir |= CONFIG_SYS_PC_IDE_RESET;
-}
-
-/* ------------------------------------------------------------------------- */
+++ /dev/null
-/*
- * (C) Copyright 2000-2010
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .text :
- {
- /* WARNING - the following is hand-optimized to fit within */
- /* the sector layout of our flash chips! XXX FIXME XXX */
-
- arch/powerpc/cpu/mpc8xx/start.o (.text*)
- arch/powerpc/cpu/mpc8xx/traps.o (.text*)
- net/built-in.o (.text*)
- arch/powerpc/cpu/mpc8xx/built-in.o (.text*)
- *(.text.v*printf)
-
- . = DEFINED(env_offset) ? env_offset : .;
- common/env_embedded.o (.ppcenv*)
-
- *(.text*)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x0FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- _GOT2_TABLE_ = .;
- KEEP(*(.got2))
- KEEP(*(.got))
- PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4);
- _FIXUP_TABLE_ = .;
- KEEP(*(.fixup))
- }
- __got2_entries = ((_GLOBAL_OFFSET_TABLE_ - _GOT2_TABLE_) >> 2) - 1;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data*)
- *(.sdata*)
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.bss*)
- *(.sbss*)
- *(COMMON)
- . = ALIGN(4);
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
+++ /dev/null
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-/* Do we need any of these for elf?
- __DYNAMIC = 0; */
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .interp : { *(.interp) }
- .hash : { *(.hash) }
- .dynsym : { *(.dynsym) }
- .dynstr : { *(.dynstr) }
- .rel.text : { *(.rel.text) }
- .rela.text : { *(.rela.text) }
- .rel.data : { *(.rel.data) }
- .rela.data : { *(.rela.data) }
- .rel.rodata : { *(.rel.rodata) }
- .rela.rodata : { *(.rela.rodata) }
- .rel.got : { *(.rel.got) }
- .rela.got : { *(.rela.got) }
- .rel.ctors : { *(.rel.ctors) }
- .rela.ctors : { *(.rela.ctors) }
- .rel.dtors : { *(.rel.dtors) }
- .rela.dtors : { *(.rela.dtors) }
- .rel.bss : { *(.rel.bss) }
- .rela.bss : { *(.rela.bss) }
- .rel.plt : { *(.rel.plt) }
- .rela.plt : { *(.rela.plt) }
- .init : { *(.init) }
- .plt : { *(.plt) }
- .text :
- {
- /* WARNING - the following is hand-optimized to fit within */
- /* the sector layout of our flash chips! XXX FIXME XXX */
-
- arch/powerpc/cpu/mpc8xx/start.o (.text)
- common/dlmalloc.o (.text)
- lib/vsprintf.o (.text)
- lib/crc32.o (.text)
- arch/powerpc/lib/extable.o (.text)
-
- . = env_offset;
- common/env_embedded.o(.text)
-
- *(.text)
- *(.got1)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(.rodata)
- *(.rodata1)
- *(.rodata.str1.4)
- *(.eh_frame)
- }
- .fini : { *(.fini) } =0
- .ctors : { *(.ctors) }
- .dtors : { *(.dtors) }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x0FFF) & 0xFFFFF000;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- *(.got)
- _GOT2_TABLE_ = .;
- *(.got2)
- _FIXUP_TABLE_ = .;
- *(.fixup)
- }
- __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data)
- *(.data1)
- *(.sdata)
- *(.sdata2)
- *(.dynamic)
- CONSTRUCTORS
- }
- _edata = .;
- PROVIDE (edata = .);
-
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(4096);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(4096);
- __init_end = .;
-
- __bss_start = .;
- .bss :
- {
- *(.sbss) *(.scommon)
- *(.dynbss)
- *(.bss)
- *(COMMON)
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
flash_info_t *
addr2info (ulong addr)
{
-#ifndef CONFIG_SPD823TS
flash_info_t *info;
int i;
return (info);
}
}
-#endif /* CONFIG_SPD823TS */
return (NULL);
}
int
flash_write (char *src, ulong addr, ulong cnt)
{
-#ifdef CONFIG_SPD823TS
- return (ERR_TIMOUT); /* any other error codes are possible as well */
-#else
int i;
ulong end = addr + cnt - 1;
flash_info_t *info_first = addr2info (addr);
#endif /* CONFIG_SYS_FLASH_VERIFY_AFTER_WRITE */
return (ERR_OK);
-#endif /* CONFIG_SPD823TS */
}
/*-----------------------------------------------------------------------
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_SPD823TS=y
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+SPD823TS powerpc mpc8xx - - Wolfgang Denk <wd@denx.de>
KUP4K powerpc mpc8xx - - Klaus Heydeck <heydeck@kieback-peter.de>
KUP4X powerpc mpc8xx - - Klaus Heydeck <heydeck@kieback-peter.de>
ELPT860 powerpc mpc8xx - - The LEOX team <team@leox.org>
#endif /* CONFIG_NETVIA */
-/*** SPD823TS ******************************************************/
-
-#ifdef CONFIG_SPD823TS
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
- */
-#define PROFF_ENET PROFF_SCC2 /* Ethernet on SCC2 */
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_MDC ((ushort)0x0001) /* PA 15 !!! */
-#define PA_ENET_MDIO ((ushort)0x0002) /* PA 14 !!! */
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-#define PC_ENET_RESET ((ushort)0x0100) /* PC 7 !!! */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK2) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002E00)
-#endif /* CONFIG_SPD823TS */
-
/*** MVS1, TQM823L/M, TQM850L/M, TQM885D, R360MPI **********/
#if (defined(CONFIG_MVS) && CONFIG_MVS < 2) || \
+++ /dev/null
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC823 1 /* This is a MPC823 CPU */
-#define CONFIG_SPD823TS 1 /* ...on a SPD823TS board */
-
-#define CONFIG_SYS_TEXT_BASE 0xFF000000
-
-#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#undef CONFIG_8xx_CONS_SMC2
-#undef CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE 115200
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
-
-#define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */
-
-#define CONFIG_BOOTARGS "root=/dev/nfs rw " \
- "nfsroot=10.0.0.2:/opt/eldk/ppc_8xx " \
- "nfsaddrs=10.0.0.99:10.0.0.2"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_IDE
-
-#undef CONFIG_CMD_SAVEENV
-#undef CONFIG_CMD_FLASH
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-/*----------------------------------------------------------------------*/
-#define CONFIG_ETHADDR 00:D0:93:00:01:CB
-#define CONFIG_IPADDR 10.0.0.98
-#define CONFIG_SERVERIP 10.0.0.1
-#undef CONFIG_BOOTCOMMAND
-#define CONFIG_BOOTCOMMAND "tftp 200000 uImage;bootm 200000"
-/*----------------------------------------------------------------------*/
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */
-
-#define CONFIG_SYS_PIO_MODE 0 /* IDE interface in PIO Mode 0 */
-
-#define CONFIG_SYS_PC_IDE_RESET ((ushort)0x0008) /* PC 12 */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFFF00000 /* was: 0xFF000000 */
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0xFF000000
-#ifdef DEBUG
-#define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */
-#else
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#endif
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 0 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 0 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 0 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 0 /* Timeout for Flash Write (in ms) */
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE 0x0800 /* Total Size of Environment Sector */
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-/* 0x00000040 */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC00 | SIUMCR_GB5E)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit, set PLL multiplication factor !
- */
-/* 0x00b0c0c0 */
-#define CONFIG_SYS_PLPRCR \
- ( (11 << PLPRCR_MF_SHIFT) | \
- PLPRCR_SPLSS | PLPRCR_TEXPS | /*PLPRCR_TMIST|*/ \
- /*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \
- PLPRCR_CSR | PLPRCR_LOLRE /*|PLPRCR_FIOPD*/ \
- )
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-/* 0x01800014 */
-#define CONFIG_SYS_SCCR (SCCR_COM00 | /*SCCR_TBS|*/ \
- SCCR_RTDIV | SCCR_RTSEL | \
- /*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \
- SCCR_EBDF00 | SCCR_DFSYNC00 | \
- SCCR_DFBRG00 | SCCR_DFNL000 | \
- SCCR_DFNH000 | SCCR_DFLCD101 | \
- SCCR_DFALCD00)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register
- *-----------------------------------------------------------------------
- */
-/* 0x00C3 */
-#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration Register
- *-----------------------------------------------------------------------
- */
-/* TIMEP=2 */
-#define CONFIG_SYS_RCCR 0x0200
-
-/*-----------------------------------------------------------------------
- * RMDS - RISC Microcode Development Support Control Register
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RMDS 0
-
-/*-----------------------------------------------------------------------
- * SDSR - SDMA Status Register
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SDSR ((u_char)0x83)
-
-/*-----------------------------------------------------------------------
- * SDMR - SDMA Mask Register
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SDMR ((u_char)0x00)
-
-/*-----------------------------------------------------------------------
- *
- * Interrupt Levels
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_CPM_INTERRUPT 13 /* SIU_LEVEL6 */
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
-#define CONFIG_IDE_INIT_POSTRESET 1 /* Use postreset IDE hook */
-#define CONFIG_IDE_8xx_DIRECT 1 /* PCMCIA interface required */
-#define CONFIG_IDE_LED 1 /* LED for ide supported */
-#define CONFIG_IDE_RESET 1 /* reset for ide supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 2 /* max. 2 IDE busses */
-#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
-
-#define CONFIG_SYS_ATA_BASE_ADDR 0xFE100000
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-#define CONFIG_SYS_ATA_IDE1_OFFSET 0x0C00
-
-#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
-#define CONFIG_SYS_ATA_REG_OFFSET 0x0080 /* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100 /* Offset for alternate registers */
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0xFF000000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0xFF080000 /* FLASH bank #1 */
-
-/* used to re-map FLASH both when starting from SRAM or FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-/* EPROMs are 512kb */
-#define CONFIG_SYS_REMAP_OR_AM 0xFFF80000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xFFF80000 /* OR addr mask */
-
-/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */
-#define CONFIG_SYS_OR_TIMING_FLASH (/* OR_CSNT_SAM | */ OR_ACS_DIV4 | OR_BI | \
- OR_SCY_5_CLK | OR_EHTR)
-
-#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-/* 16 bit, bank valid */
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
-/* 16 bit, bank valid */
-#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
-
-/*
- * BR2-5 and OR2-5 (SRAM/SDRAM/PER8/SHARC)
- *
- */
-#define SRAM_BASE 0xFE200000 /* SRAM bank */
-#define SRAM_OR_AM 0xFFE00000 /* SRAM is 2 MB */
-
-#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank */
-#define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */
-#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB SDRAM */
-
-#define PER8_BASE 0xFE000000 /* PER8 bank */
-#define PER8_OR_AM 0xFFF00000 /* PER8 is 1 MB */
-
-#define SHARC_BASE 0xFE400000 /* SHARC bank */
-#define SHARC_OR_AM 0xFFC00000 /* SHARC is 4 MB */
-
-/* SRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-
-#define CONFIG_SYS_OR_TIMING_SRAM 0x00000D42 /* SRAM-Timing */
-#define CONFIG_SYS_OR2 (SRAM_OR_AM | CONFIG_SYS_OR_TIMING_SRAM )
-#define CONFIG_SYS_BR2 ((SRAM_BASE & BR_BA_MSK) | BR_PS_16 | BR_V )
-
-/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-
-#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00 /* SDRAM-Timing */
-#define CONFIG_SYS_OR3_PRELIM (SDRAM_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
-#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_V )
-
-#define CONFIG_SYS_OR_TIMING_PER8 0x00000F32 /* PER8-Timing */
-#define CONFIG_SYS_OR4 (PER8_OR_AM | CONFIG_SYS_OR_TIMING_PER8 )
-#define CONFIG_SYS_BR4 ((PER8_BASE & BR_BA_MSK) | BR_PS_8 | BR_V )
-
-#define CONFIG_SYS_OR_TIMING_SHARC 0x00000700 /* SHARC-Timing */
-#define CONFIG_SYS_OR5 (SHARC_OR_AM | CONFIG_SYS_OR_TIMING_SHARC )
-#define CONFIG_SYS_BR5 ((SHARC_BASE & BR_BA_MSK) | BR_PS_32 | BR_MS_UPMA | BR_V )
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MBMR_PTB 204
-
-/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
-#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * MBMR settings for SDRAM
- */
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MBMR_8COL ((CONFIG_SYS_MBMR_PTB << MBMR_PTB_SHIFT) | \
- MBMR_AMB_TYPE_0 | MBMR_DSB_1_CYCL | MBMR_G0CLB_A11 | \
- MBMR_RLFB_1X | MBMR_WLFB_1X | MBMR_TLFB_4X)
-
-#endif /* __CONFIG_H */
#if defined(CONFIG_TQM8xxL)
# define CONFIG_PCMCIA_SLOT_B /* The TQM8xxL use SLOT_B */
-#elif defined(CONFIG_SPD823TS) /* The SPD8xx use SLOT_B */
-# define CONFIG_PCMCIA_SLOT_B
#elif defined(CONFIG_IVMS8) || defined(CONFIG_IVML24) /* The IVM* use SLOT_A */
# define CONFIG_PCMCIA_SLOT_A
#elif defined(CONFIG_LWMON) /* The LWMON use SLOT_B */
projects / u-boot / commitdiff