--- /dev/null
+Freescale MPC8349E-mITX and MPC8349E-mITX-GP Boards
+---------------------------------------------------
+
+1. Board Description
+
+ The MPC8349E-mITX and MPC8349E-mITX-GP are reference boards featuring
+ the Freescale MPC8349E processor in a Mini-ITX form factor.
+
+ The MPC8349E-mITX-GP is an MPC8349E-mITX with the following differences:
+
+ A) One 8MB on-board flash EEPROM chip, instead of two.
+ B) No SATA controller
+ C) No Compact Flash slot
+ D) No Mini-PCI slot
+ E) No Vitesse 7385 5-port Ethernet switch
+ F) No 4-port USB Type-A interface
+
+2. Board Switches and Jumpers
+
+2.0 Descriptions for all of the board jumpers can be found in the User
+ Guide. Of particular interest to U-Boot developers is jumper J22:
+
+ Pos. Name Default Description
+ -----------------------------------------------------------------------
+ A LGPL0 ON (0) HRCW source, bit 0
+ B LGPL1 ON (0) HRCW source, bit 1
+ C LGPL3 ON (0) HRCW source, bit 2
+ D LGPL5 OFF (1) PCI_SYNC_OUT frequency
+ E BOOT1 ON (0) Flash EEPROM boot device
+ F PCI_M66EN ON (0) PCI 66MHz enable
+ G I2C-WP ON (0) I2C EEPROM write protection
+ H F_WP OFF (1) Flash EEPROM write protection
+
+ Jumper J22.E is only for the ITX, and it decides the configuration
+ of the flash chips. If J22.E is ON (i.e. jumpered), then flash chip
+ U4 is located at address FE000000 and flash chip U7 is at FE800000.
+ If J22.E is OFF, then U7 is at FE000000 and U4 is at FE800000.
+
+ For U-Boot development, J22.E can be used to switch back-and-forth
+ between two U-Boot images.
+
+3. Memory Map
+
+3.1. The memory map should look pretty much like this:
+
+ 0x0000_0000 - 0x0FFF_FFFF DDR SDRAM (256 MB)
+ 0x8000_0000 - 0x9FFF_FFFF PCI1 memory space (512 MB)
+ 0xA000_0000 - 0xBFFF_FFFF PCI2 memory space (512 MB)
+ 0xE000_0000 - 0xEFFF_FFFF IMMR (1 MB)
+ 0xE200_0000 - 0xE2FF_FFFF PCI1 I/O space (16 MB)
+ 0xE300_0000 - 0xE3FF_FFFF PCI2 I/O space (16 MB)
+ 0xF000_0000 - 0xF000_FFFF Compact Flash (ITX only)
+ 0xF001_0000 - 0xF001_FFFF Local bus expansion slot
+ 0xF800_0000 - 0xF801_FFFF Vitesse 7385 Parallel Interface (ITX only)
+ 0xFE00_0000 - 0xFE7F_FFFF First 8MB bank of Flash memory
+ 0xFE80_0000 - 0xFEFF_FFFF Second 8MB bank of Flash memory (ITX only)
+
+3.2 Flash EEPROM layout.
+
+ On the ITX, jumper J22.E is used to determine which flash chips are
+ at which address. When J22.E is switched, addresses from FE000000
+ to FE7FFFFF are swapped with addresses from FE800000 to FEFFFFFF.
+
+ On the ITX, at the normal boot address (aka HIGHBOOT):
+
+ FE00_0000 HRCW
+ FE70_0000 Alternative U-Boot image
+ FE80_0000 Alternative HRCW
+ FEF0_0000 U-Boot image
+ FEFF_FFFF End of flash
+
+ On the ITX, at the low boot address (LOWBOOT)
+
+ FE00_0000 HRCW and U-Boot image
+ FE04_0000 U-Boot environment variables
+ FE80_0000 Alternative HRCW and U-Boot image
+ FEFF_FFFF End of flash
+
+ On the ITX-GP, the only option is LOWBOOT and there is only one chip
+
+ FE00_0000 HRCW and U-Boot image
+ FE04_0000 U-Boot environment variables
+ F7FF_FFFF End of flash
+
+4. Definitions
+
+4.1 Explanation of NEW definitions in:
+
+ include/configs/MPC8349ITX.h
+
+ CONFIG_MPC83XX MPC83xx family
+ CONFIG_MPC8349 MPC8349 specific
+ CONFIG_MPC8349ITX MPC8349E-mITX
+ CONFIG_MPC8349ITXGP MPC8349E-mITX-GP
+
+5. Compilation
+
+ Assuming you're using BASH shell:
+
+ export CROSS_COMPILE=your-cross-compile-prefix
+ cd u-boot
+ make distclean
+
+ make MPC8349ITX_config
+ or:
+ make MPC8349ITXGP_config
+ or:
+ make MPC8349ITX_LOWBOOT_config
+
+ make
+
+6. Downloading and Flashing Images
+
+6.1 Download via tftp:
+
+ tftp $loadaddr <uboot>
+
+ where "<uboot>" is the path and filename, on the TFTP server, of
+ the U-Boot image.
+
+6.1 Reflash U-Boot Image using U-Boot
+
+ setenv uboot <uboot>
+ run tftpflash
+
+ where "<uboot>" is the path and filename, on the TFTP server, of
+ the U-Boot image.
+
+6.2 Using the HRCW to switch between two different U-Boot images on the ITX
+
+ Because the ITX has 16MB of flash, it is possible to keep two U-Boot
+ images in flash, and use the HRCW to specify which one is to be used
+ when the board boots. This trick is especially effective with a
+ hardware debugger that can override the HRCW, such as the BDI-2000.
+
+ When the BMS bit in the HRCW is 0, the ITX will boot the U-Boot image
+ at address FE000000. When the BMS bit is 1, the ITX will boot the
+ image at address FEF00000.
+
+ Therefore, just put a U-Boot image at both FE000000 and FEF00000 and
+ change the BMS bit whenever you want to boot the other image.
+
+ Step-by-step instructions:
+
+ 1) Build an ITX image to be loaded at FEF00000
+
+ make distclean
+ make MPC8349ITX_config
+ make
+
+ 2) Take the u-boot.bin image and flash it at FEF00000.
+
+ tftp $loadaddr u-boot.bin
+ protect off all
+ erase FEF00000 +$filesize
+ cp.b $loadaddr FEF00000 $filesize
+
+ 3) Build an ITX image to be loaded at FE000000
+
+ make distclean
+ make MPC8349ITX_LOWBOOT_config
+ make
+
+ 4) Take the u-boot.bin image and flash it at FE000000.
+
+ tftp $loadaddr u-boot.bin
+ protect off FE000000 +$filesize
+ erase FE000000 +$filesize
+ cp.b $loadaddr FE000000 $filesize
+
+ The HRCW in flash is currently set to boot the image at FE000000.
+
+ If you have a hardware debugger, configure it to set the HRCW to
+ B460A000 04040000 if you want to boot the image at FEF00000, or set
+ it to B060A000 04040000 if you want to boot the image at FE000000.
+
+ To change the HRCW in flash to boot the image at FEF00000, use these
+ U-Boot commands:
+
+ cp.b FE000000 1000 10000 ; copy 1st flash sector to 1000
+ mw.b 1020 b4 8 ; modify BMS bit
+ protect off FE000000 +10000
+ erase FE000000 +10000
+ cp.b 1000 FE000000 10000
+
+7. Notes
+ 1) The console baudrate for MPC8349EITX is 115200bps.
*/
/*
- MPC8349E-mITX board configuration file
+ MPC8349E-mITX and MPC8349E-mITX-GP board configuration file
Memory map:
0xE000_0000-0xEFFF_FFFF IMMR (1 MB)
0xE200_0000-0xE2FF_FFFF PCI1 I/O space (16 MB)
0xE300_0000-0xE3FF_FFFF PCI2 I/O space (16 MB)
- 0xF000_0000-0xF000_FFFF Compact Flash
+ 0xF000_0000-0xF000_FFFF Compact Flash (MPC8349E-mITX only)
0xF001_0000-0xF001_FFFF Local bus expansion slot
- 0xF800_0000-0xF801_FFFF GBE L2 Switch VSC7385
- 0xFF00_0000-0xFF7F_FFFF Alternative bank of Flash memory (8MB)
- 0xFF80_0000-0xFFFF_FFFF Boot Flash (8 MB)
+ 0xF800_0000-0xF801_FFFF Vitesse 7385 Parallel Interface (MPC8349E-mITX only)
+ 0xFE00_0000-0xFE7F_FFFF First 8MB bank of Flash memory
+ 0xFE80_0000-0xFEFF_FFFF Second 8MB bank of Flash memory (MPC8349E-mITX only)
I2C address list:
Align. Board
#ifndef __CONFIG_H
#define __CONFIG_H
-#undef DEBUG
+#if (TEXT_BASE == 0xFE000000)
+#define CFG_LOWBOOT
+#endif
/*
* High Level Configuration Options
#define CONFIG_MPC834X /* MPC834x family (8343, 8347, 8349) */
#define CONFIG_MPC8349 /* MPC8349 specific */
-#define CONFIG_PCI
+#define CFG_IMMR 0xE0000000 /* The IMMR is relocated to here */
+
+
+/* On-board devices */
+#ifdef CONFIG_MPC8349ITX
#define CONFIG_COMPACT_FLASH /* The CF card interface on the back of the board */
-#define CONFIG_RTC_DS1337
+#define CONFIG_VSC7385 /* The Vitesse 7385 5-port switch */
+#endif
-/* I2C */
+#define CONFIG_PCI
+#define CONFIG_RTC_DS1337
#define CONFIG_HARD_I2C
+#define CONFIG_TSEC_ENET /* TSEC Ethernet support */
+/*
+ * Device configurations
+ */
+
+/* I2C */
#ifdef CONFIG_HARD_I2C
#define CONFIG_MISC_INIT_F
#endif
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
-#define CONFIG_ENV_OVERWRITE
+/* Compact Flash */
+#ifdef CONFIG_COMPACT_FLASH
-#define PCI_66M
-#ifdef PCI_66M
-#define CONFIG_83XX_CLKIN 66666666 /* in Hz */
-#else
-#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
-#endif
+#define CFG_IDE_MAXBUS 1
+#define CFG_IDE_MAXDEVICE 1
-#ifndef CONFIG_SYS_CLK_FREQ
-#ifdef PCI_66M
-#define CONFIG_SYS_CLK_FREQ 66666666
-#else
-#define CONFIG_SYS_CLK_FREQ 33333333
-#endif
-#endif
+#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CFG_ATA_BASE_ADDR CFG_CF_BASE
+#define CFG_ATA_DATA_OFFSET 0x0000
+#define CFG_ATA_REG_OFFSET 0
+#define CFG_ATA_ALT_OFFSET 0x0200
+#define CFG_ATA_STRIDE 2
-#define CFG_IMMR 0xE0000000 /* The IMMR is relocated to here */
+#define ATA_RESET_TIME 1 /* If a CF card is not inserted, time out quickly */
-#undef CFG_DRAM_TEST /* memory test, takes time */
-#define CFG_MEMTEST_START 0x00003000 /* memtest region */
-#define CFG_MEMTEST_END 0x07100000 /* only has 128M */
+#define CONFIG_DOS_PARTITION
-/*
- * DDR Setup
- */
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
-#undef CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */
-#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
+#endif
/*
- * 32-bit data path mode.
- *
- * Please note that using this mode for devices with the real density of 64-bit
- * effectively reduces the amount of available memory due to the effect of
- * wrapping around while translating address to row/columns, for example in the
- * 256MB module the upper 128MB get aliased with contents of the lower
- * 128MB); normally this define should be used for devices with real 32-bit
- * data path.
+ * DDR Setup
*/
-#undef CONFIG_DDR_32BIT
-
-#define CFG_DDR_BASE 0x00000000 /* DDR is system memory*/
-#define CFG_SDRAM_BASE CFG_DDR_BASE
-#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE
-#undef CONFIG_DDR_2T_TIMING
+#define CFG_DDR_BASE 0x00000000 /* DDR is system memory*/
+#define CFG_SDRAM_BASE CFG_DDR_BASE
+#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE
#define CFG_83XX_DDR_USES_CS0
+#define CFG_MEMTEST_START 0x1000 /* memtest region */
+#define CFG_MEMTEST_END 0x2000
-#ifndef CONFIG_SPD_EEPROM
-/*
- * Manually set up DDR parameters
- */
+#ifdef CONFIG_HARD_I2C
+#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
+#endif
+
+#ifndef CONFIG_SPD_EEPROM /* No SPD? Then manually set up DDR parameters */
#define CFG_DDR_SIZE 256 /* Mb */
#define CFG_DDR_CONFIG (CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
#define CFG_DDR_TIMING_2 0x00000800 /* P9-45, may need tuning */
#endif
-/* FLASH on the Local Bus */
+/*
+ *Flash on the Local Bus
+ */
+
#define CFG_FLASH_CFI /* use the Common Flash Interface */
#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
#define CFG_FLASH_BASE 0xFE000000 /* start of FLASH */
-#define CFG_FLASH_SIZE 16 /* FLASH size in MB */
#define CFG_FLASH_EMPTY_INFO
+#define CFG_MAX_FLASH_SECT 135 /* 127 64KB sectors + 8 8KB sectors per device */
+#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+#define CFG_FLASH_CFI_WIDTH FLASH_CFI_16BIT
+
+/* The ITX has two flash chips, but the ITX-GP has only one. To support both
+boards, we say we have two, but don't display a message if we find only one. */
+#define CFG_FLASH_QUIET_TEST
+#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
+#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE + 0x800000}
+#define CFG_FLASH_SIZE 16 /* FLASH size in MB */
+#define CFG_FLASH_SIZE_SHIFT 4 /* log2 of the above value */
+
+/*
+ * BRx, ORx, LBLAWBARx, and LBLAWARx
+ */
+
+/* Flash */
#define CFG_BR0_PRELIM (CFG_FLASH_BASE | BR_PS_16 | BR_V)
#define CFG_OR0_PRELIM ((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \
OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \
OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
-#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */
-#define CFG_LBLAWAR0_PRELIM 0x80000017 /* 16Mb window bytes */
+#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE
+#define CFG_LBLAWAR0_PRELIM (LBLAWAR_EN | (0x13 + CFG_FLASH_SIZE_SHIFT))
-/* VSC7385 on the Local Bus */
-#define CFG_VSC7385_BASE 0xF8000000 /* start of VSC7385 */
+/* Vitesse 7385 */
-#define CFG_BR1_PRELIM (CFG_VSC7385_BASE | BR_PS_8 | BR_V)
-#define CFG_OR1_PRELIM (0xFFFE0000 /* 128KB */ | \
- OR_GPCM_CSNT | OR_GPCM_XACS | OR_GPCM_SCY_15 | \
- OR_GPCM_SETA | OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
+#ifdef CONFIG_VSC7385
-#define CFG_LBLAWBAR1_PRELIM CFG_VSC7385_BASE /* Access window base at VSC7385 base */
-#define CFG_LBLAWAR1_PRELIM 0x80000010 /* Access window size 128K */
+#define CFG_VSC7385_BASE 0xF8000000
-#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
-#define CFG_MAX_FLASH_SECT 135 /* sectors per device */
+#define CFG_BR1_PRELIM (CFG_VSC7385_BASE | BR_PS_8 | BR_V)
+#define CFG_OR1_PRELIM (OR_AM_128KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
+ OR_GPCM_SCY_15 | OR_GPCM_SETA | OR_GPCM_TRLX | \
+ OR_GPCM_EHTR | OR_GPCM_EAD)
-#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE + 0x800000}
+#define CFG_LBLAWBAR1_PRELIM CFG_VSC7385_BASE
+#define CFG_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_128KB)
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+#endif
-#define CFG_LED_BASE 0xF9000000 /* start of LED and Board ID */
+/* LED */
+
+#define CFG_LED_BASE 0xF9000000
#define CFG_BR2_PRELIM (CFG_LED_BASE | BR_PS_8 | BR_V)
-#define CFG_OR2_PRELIM (0xFFE00000 /* 2MB */ | \
- OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | OR_GPCM_XACS | \
- OR_GPCM_SCY_9 | \
- OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
+#define CFG_OR2_PRELIM (OR_AM_2MB | OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | \
+ OR_GPCM_XACS | OR_GPCM_SCY_9 | OR_GPCM_TRLX | \
+ OR_GPCM_EHTR | OR_GPCM_EAD)
+
+/* Compact Flash */
#ifdef CONFIG_COMPACT_FLASH
#define CFG_BR3_PRELIM (CFG_CF_BASE | BR_PS_16 | BR_MS_UPMA | BR_V)
#define CFG_OR3_PRELIM (OR_UPM_AM | OR_UPM_BI)
-#define CFG_LBLAWBAR2_PRELIM CFG_CF_BASE /* Window base at flash base + LED & Board ID */
-#define CFG_LBLAWAR2_PRELIM 0x8000000F /* 64K bytes */
-
-#undef CONFIG_IDE_RESET
-#undef CONFIG_IDE_PREINIT
-
-#define CFG_IDE_MAXBUS 1
-#define CFG_IDE_MAXDEVICE 1
-
-#define CFG_ATA_IDE0_OFFSET 0x0000
-#define CFG_ATA_BASE_ADDR CFG_CF_BASE
-#define CFG_ATA_DATA_OFFSET 0x0000
-#define CFG_ATA_REG_OFFSET 0
-#define CFG_ATA_ALT_OFFSET 0x0200
-#define CFG_ATA_STRIDE 2
-
-#define ATA_RESET_TIME 1 /* If a CF card is not inserted, time out quickly */
+#define CFG_LBLAWBAR3_PRELIM CFG_CF_BASE
+#define CFG_LBLAWAR3_PRELIM (LBLAWAR_EN | LBLAWAR_64KB)
#endif
-#define CONFIG_DOS_PARTITION
-
-#define CFG_MID_FLASH_JUMP 0x7F000000
+/*
+ * U-Boot memory configuration
+ */
#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
-
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
#define CFG_RAMBOOT
#else
#define CONFIG_L1_INIT_RAM
#define CFG_INIT_RAM_LOCK
-#define CFG_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM*/
+#define CFG_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM*/
-#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
+#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_4)
#define CFG_LBC_LBCR 0x00000000
-#undef CFG_LB_SDRAM /* if board has SRDAM on local bus */
-
-#ifdef CFG_LB_SDRAM
-/*local bus BR2, OR2 definition for SDRAM if soldered on the ADS board*/
-/*
- * Base Register 2 and Option Register 2 configure SDRAM.
- * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
- *
- * For BR2, need:
- * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
- * port-size = 32-bits = BR2[19:20] = 11
- * no parity checking = BR2[21:22] = 00
- * SDRAM for MSEL = BR2[24:26] = 011
- * Valid = BR[31] = 1
- *
- * 0 4 8 12 16 20 24 28
- * 1111 0000 0000 0000 0001 1000 0110 0001 = F0001861
- */
-
-#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
-#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
-
-#define CFG_LBLAWBAR2_PRELIM 0xF0000000
-#define CFG_LBLAWAR2_PRELIM 0x80000019 /* 64M */
-
-#define CFG_BR2_PRELIM (CFG_LBC_SDRAM_BASE | BR_PS_32 | BR_MS_SDRAM | BR_V)
-#define CFG_OR2_PRELIM (0xFC000000 /* 64 MB */ | \
- OR_SDRAM_XAM | \
- ((9 - 7) << OR_SDRAM_COLS_SHIFT) | \
- ((13 - 9) << OR_SDRAM_ROWS_SHIFT) | \
- OR_SDRAM_EAD)
-
#define CFG_LBC_LSRT 0x32000000 /* LB sdram refresh timer, about 6us */
#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal, 266MHz/32*/
-/*
- * LSDMR masks
- */
-#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1))
-#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10))
-#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10))
-#define CFG_LBC_LSDMR_RFCR5 (3 << (31 - 16))
-#define CFG_LBC_LSDMR_RFCR8 (5 << (31 - 16))
-#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16))
-#define CFG_LBC_LSDMR_PRETOACT3 (3 << (31 - 19))
-#define CFG_LBC_LSDMR_PRETOACT6 (5 << (31 - 19))
-#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19))
-#define CFG_LBC_LSDMR_ACTTORW3 (3 << (31 - 22))
-#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22))
-#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22))
-#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23))
-#define CFG_LBC_LSDMR_WRC2 (2 << (31 - 27))
-#define CFG_LBC_LSDMR_WRC3 (3 << (31 - 27))
-#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27))
-#define CFG_LBC_LSDMR_BUFCMD (1 << (31 - 29))
-#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31))
-
-#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
-
-#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_RFEN \
- | CFG_LBC_LSDMR_BSMA1516 \
- | CFG_LBC_LSDMR_RFCR8 \
- | CFG_LBC_LSDMR_PRETOACT6 \
- | CFG_LBC_LSDMR_ACTTORW3 \
- | CFG_LBC_LSDMR_BL8 \
- | CFG_LBC_LSDMR_WRC3 \
- | CFG_LBC_LSDMR_CL3 \
- )
-
-/*
- * SDRAM Controller configuration sequence.
- */
-#define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_PCHALL)
-#define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_ARFRSH)
-#define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_ARFRSH)
-#define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_MRW)
-#define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_NORMAL)
-#endif
-
/*
* Serial Port
*/
#define CFG_NS16550_CLK get_bus_freq(0)
#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+#define CONFIG_BAUDRATE 115200
#define CFG_NS16550_COM1 (CFG_IMMR + 0x4500)
#define CFG_NS16550_COM2 (CFG_IMMR + 0x4600)
-/* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
-#endif
-
/* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE 1
-#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_FLAT_TREE
+#define CONFIG_OF_BOARD_SETUP
/* maximum size of the flat tree (8K) */
#define OF_FLAT_TREE_MAX_SIZE 8192
#define OF_TBCLK (bd->bi_busfreq / 4)
#define OF_STDOUT_PATH "/soc8349@e0000000/serial@4500"
+/*
+ * PCI
+ */
#ifdef CONFIG_PCI
#define CONFIG_MPC83XX_PCI2
#endif
+#define PCI_66M
+#ifdef PCI_66M
+#define CONFIG_83XX_CLKIN 66666666 /* in Hz */
+#else
+#define CONFIG_83XX_CLKIN 33333333 /* in Hz */
+#endif
+
/* TSEC */
#ifdef CONFIG_TSEC_ENET
-#ifndef CONFIG_NET_MULTI
#define CONFIG_NET_MULTI
-#endif
-
#define CONFIG_MII
#define CONFIG_PHY_GIGE /* In case CFG_CMD_MII is specified */
#endif
#ifdef CONFIG_MPC83XX_TSEC2
+#define CONFIG_HAS_ETH1
#define CONFIG_MPC83XX_TSEC2_NAME "TSEC1"
#define CFG_TSEC2_OFFSET 0x25000
#define CONFIG_UNKNOWN_TSEC /* TSEC2 is proprietary */
#endif
-
/*
* Environment
*/
+#define CONFIG_ENV_OVERWRITE
+
#ifndef CFG_RAMBOOT
#define CFG_ENV_IS_IN_FLASH
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
- #define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
+ #define CFG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) for environment */
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE + (4 * CFG_ENV_SECT_SIZE))
#define CFG_ENV_SIZE 0x2000
#else
#define CFG_NO_FLASH /* Flash is not usable now */
/* Watchdog */
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#ifdef CONFIG_WATCHDOG
-#define CFG_WATCHDOG_VALUE 0xFFFFFFC3
-#endif
/*
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CFG_HUSH_PARSER /* Use the HUSH parser */
+#define CFG_PROMPT_HUSH_PS2 "> "
+
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
-#define CFG_PROMPT "MPC8349E-mITX> " /* Monitor Command Prompt */
+#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
+
+#ifdef CONFIG_MPC8349ITX
+#define CFG_PROMPT "MPC8349E-mITX> " /* Monitor Command Prompt */
+#else
+#define CFG_PROMPT "MPC8349E-mITX-GP> " /* Monitor Command Prompt */
+#endif
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
-/* Cache Configuration */
+/*
+ * Cache Configuration
+ */
#define CFG_DCACHE_SIZE 32768
#define CFG_CACHELINE_SIZE 32
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log2 of the above value */
#endif
-#define CFG_RCWH_PCIHOST 0x80000000 /* PCIHOST */
-
#define CFG_HRCW_LOW (\
HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
HRCWL_DDR_TO_SCB_CLK_1X1 |\
HRCWL_VCO_1X2 |\
HRCWL_CORE_TO_CSB_2X1)
-#ifdef PCI_64BIT
+#ifdef CFG_LOWBOOT
#define CFG_HRCW_HIGH (\
HRCWH_PCI_HOST |\
- HRCWH_64_BIT_PCI |\
+ HRCWH_32_BIT_PCI |\
HRCWH_PCI1_ARBITER_ENABLE |\
- HRCWH_PCI2_ARBITER_DISABLE |\
+ HRCWH_PCI2_ARBITER_ENABLE |\
HRCWH_CORE_ENABLE |\
HRCWH_FROM_0X00000100 |\
HRCWH_BOOTSEQ_DISABLE |\
HRCWH_PCI_HOST |\
HRCWH_32_BIT_PCI |\
HRCWH_PCI1_ARBITER_ENABLE |\
- HRCWH_PCI2_ARBITER_DISABLE |\
+ HRCWH_PCI2_ARBITER_ENABLE |\
HRCWH_CORE_ENABLE |\
HRCWH_FROM_0XFFF00100 |\
HRCWH_BOOTSEQ_DISABLE |\
HRCWH_TSEC2M_IN_GMII )
#endif
-/* System performance */
+/*
+ * System performance
+ */
#define CFG_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
#define CFG_SPCR_TSEC1EP 3 /* TSEC1 emergency priority (0-3) */
#define CFG_SPCR_TSEC2EP 3 /* TSEC2 emergency priority (0-3) */
#define CFG_SCCR_TSEC1CM 1 /* TSEC1 clock mode (0-3) */
#define CFG_SCCR_TSEC2CM 1 /* TSEC2 & I2C0 clock mode (0-3) */
-#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count */
-/* System IO Config */
+/*
+ * System IO Config
+ */
#define CFG_SICRH SICRH_TSOBI1 /* Needed for gigabit to work on TSEC 1 */
#define CFG_SICRL (SICRL_LDP_A | SICRL_USB1)
-#define CFG_HID0_INIT 0x000000000
-
-#define CFG_HID0_FINAL CFG_HID0_INIT
+#define CFG_HID0_INIT 0x000000000
+#define CFG_HID0_FINAL CFG_HID0_INIT
#define CFG_HID2 HID2_HBE
-/* DDR @ 0x00000000 */
+/* DDR */
#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-/* PCI @ 0x80000000 */
+/* PCI */
#ifdef CONFIG_PCI
#define CFG_IBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
#define CFG_IBAT1U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#endif
#ifdef CONFIG_MPC83XX_TSEC2
-#define CONFIG_HAS_ETH1
#define CONFIG_ETH1ADDR 00:E0:0C:00:8C:02
#endif
-#if 1
-#define CONFIG_IPADDR 10.82.19.159
-#define CONFIG_SERVERIP 10.82.48.106
-#define CONFIG_GATEWAYIP 10.82.19.254
-#define CONFIG_NETMASK 255.255.252.0
-#define CONFIG_NETDEV eth0
-
-#define CONFIG_HOSTNAME mpc8349emitx
-#define CONFIG_ROOTPATH /nfsroot0/u/timur/itx-ltib/rootfs
-#define CONFIG_BOOTFILE timur/uImage
-
-#define CONFIG_UBOOTPATH timur/u-boot.bin
-#else
#define CONFIG_IPADDR 192.168.1.253
#define CONFIG_SERVERIP 192.168.1.1
#define CONFIG_GATEWAYIP 192.168.1.1
#define CONFIG_NETMASK 255.255.252.0
#define CONFIG_NETDEV eth0
+#ifdef CONFIG_MPC8349ITX
#define CONFIG_HOSTNAME mpc8349emitx
-#define CONFIG_ROOTPATH /nfsroot/rootfs
-#define CONFIG_BOOTFILE uImage
-
-#define CONFIG_UBOOTPATH u-boot.bin
+#else
+#define CONFIG_HOSTNAME mpc8349emitxgp
#endif
-#define CONFIG_UBOOTSTART fe700000
-#define CONFIG_UBOOTEND fe77ffff
-
-#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
-
-#define CONFIG_BAUDRATE 115200
+/* Default path and filenames */
+#define CONFIG_ROOTPATH /nfsroot/rootfs
+#define CONFIG_BOOTFILE uImage
+#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
-#undef CONFIG_BOOTCOMMAND
-#ifdef CONFIG_BOOTCOMMAND
-#define CONFIG_BOOTDELAY 6
+#ifdef CONFIG_MPC8349ITX
+#define CONFIG_FDTFILE mpc8349emitx.dtb
#else
-#define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */
+#define CONFIG_FDTFILE mpc8349emitxgp.dtb
#endif
+#define CONFIG_BOOTDELAY 0
+
#define XMK_STR(x) #x
#define MK_STR(x) XMK_STR(x)
#define CONFIG_BOOTARGS \
"root=/dev/nfs rw" \
" nfsroot=" MK_STR(CONFIG_SERVERIP) ":" MK_STR(CONFIG_ROOTPATH) \
- " ip=" MK_STR(CONFIG_IPADDR) ":" MK_STR(CONFIG_SERVERIP) ":" \
+ " ip=" MK_STR(CONFIG_IPADDR) ":" MK_STR(CONFIG_SERVERIP) ":" \
MK_STR(CONFIG_GATEWAYIP) ":" MK_STR(CONFIG_NETMASK) ":" \
MK_STR(CONFIG_HOSTNAME) ":" MK_STR(CONFIG_NETDEV) ":off" \
" console=ttyS0," MK_STR(CONFIG_BAUDRATE)
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=" MK_STR(CONFIG_NETDEV) "\0" \
- "tftpflash=tftpboot $loadaddr " MK_STR(CONFIG_UBOOTPATH) "; " \
- "erase " MK_STR(CONFIG_UBOOTSTART) " " MK_STR(CONFIG_UBOOTEND) "; " \
- "cp.b $loadaddr " MK_STR(CONFIG_UBOOTSTART) " $filesize; " \
- "cmp.b $loadaddr " MK_STR(CONFIG_UBOOTSTART) " $filesize\0" \
- "tftpupdate=tftpboot $loadaddr " MK_STR(CONFIG_UBOOTPATH) "; " \
- "protect off FEF00000 FEF7FFFF; " \
- "erase FEF00000 FEF7FFFF; " \
- "cp.b $loadaddr FEF00000 $filesize; " \
- "protect on FEF00000 FEF7FFFF; " \
- "cmp.b $loadaddr FEF00000 $filesize\0" \
- "tftplinux=tftpboot $loadaddr $bootfile; bootm\0" \
- "copyuboot=erase " MK_STR(CONFIG_UBOOTSTART) " " MK_STR(CONFIG_UBOOTEND) "; " \
- "cp.b fef00000 " MK_STR(CONFIG_UBOOTSTART) " 80000\0" \
+ "netdev=" MK_STR(CONFIG_NETDEV) "\0" \
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot; " \
+ "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
+ "erase " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
+ "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
"fdtaddr=400000\0" \
- "fdtfile=mpc8349emitx.dtb\0" \
- ""
+ "fdtfile=" MK_STR(CONFIG_FDTFILE) "\0"
#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
+ "setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath" \
+ " ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ " console=$console,$baudrate $othbootargs; " \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
+ "setenv bootargs root=/dev/ram rw" \
+ " console=$console,$baudrate $othbootargs; " \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
#undef MK_STR
#undef XMK_STR
projects / u-boot / commitdiff