]> git.sur5r.net Git - u-boot/commitdiff
i2c: mv_i2c.c: Prepare driver for DM conversion
authorStefan Roese <sr@denx.de>
Fri, 16 Sep 2016 13:07:51 +0000 (15:07 +0200)
committerHeiko Schocher <hs@denx.de>
Mon, 26 Sep 2016 08:41:17 +0000 (10:41 +0200)
To prepare for the DM conversion, we add a layer of compatibility
functions to be used by both the legacy and the DM functions.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Heiko Schocher <hs@denx.de>
drivers/i2c/mv_i2c.c

index 36482d5af3a35a113676a6554fa3e5601ca95c95..30b986e705a45aa3c28e803958dac8258042307b 100644 (file)
@@ -18,9 +18,8 @@
  */
 
 #include <common.h>
-#include <asm/io.h>
-
 #include <i2c.h>
+#include <asm/io.h>
 #include "mv_i2c.h"
 
 /* All transfers are described by this data structure */
@@ -43,62 +42,11 @@ struct mv_i2c {
        u32 isar;
 };
 
-static struct mv_i2c *base;
-static void i2c_board_init(struct mv_i2c *base)
-{
-#ifdef CONFIG_SYS_I2C_INIT_BOARD
-       u32 icr;
-       /*
-        * call board specific i2c bus reset routine before accessing the
-        * environment, which might be in a chip on that bus. For details
-        * about this problem see doc/I2C_Edge_Conditions.
-        *
-        * disable I2C controller first, otherwhise it thinks we want to
-        * talk to the slave port...
-        */
-       icr = readl(&base->icr);
-       writel(readl(&base->icr) & ~(ICR_SCLE | ICR_IUE), &base->icr);
-
-       i2c_init_board();
-
-       writel(icr, &base->icr);
-#endif
-}
-
-#ifdef CONFIG_I2C_MULTI_BUS
-static unsigned long i2c_regs[CONFIG_MV_I2C_NUM] = CONFIG_MV_I2C_REG;
-static unsigned int bus_initialized[CONFIG_MV_I2C_NUM];
-static unsigned int current_bus;
-
-int i2c_set_bus_num(unsigned int bus)
-{
-       if ((bus < 0) || (bus >= CONFIG_MV_I2C_NUM)) {
-               printf("Bad bus: %d\n", bus);
-               return -1;
-       }
-
-       base = (struct mv_i2c *)i2c_regs[bus];
-       current_bus = bus;
-
-       if (!bus_initialized[current_bus]) {
-               i2c_board_init(base);
-               bus_initialized[current_bus] = 1;
-       }
-
-       return 0;
-}
-
-unsigned int i2c_get_bus_num(void)
-{
-       return current_bus;
-}
-#endif
-
 /*
  * i2c_reset: - reset the host controller
  *
  */
-static void i2c_reset(void)
+static void i2c_reset(struct mv_i2c *base)
 {
        writel(readl(&base->icr) & ~ICR_IUE, &base->icr); /* disable unit */
        writel(readl(&base->icr) | ICR_UR, &base->icr);   /* reset the unit */
@@ -120,7 +68,7 @@ static void i2c_reset(void)
  *
  * @return: 1 in case of success, 0 means timeout (no match within 10 ms).
  */
-static int i2c_isr_set_cleared(unsigned long set_mask,
+static int i2c_isr_set_cleared(struct mv_i2c *base, unsigned long set_mask,
                               unsigned long cleared_mask)
 {
        int timeout = 1000, isr;
@@ -150,7 +98,7 @@ static int i2c_isr_set_cleared(unsigned long set_mask,
  *          -5: illegal parameters
  *          -6: bus is busy and couldn't be aquired
  */
-int i2c_transfer(struct mv_i2c_msg *msg)
+static int i2c_transfer(struct mv_i2c *base, struct mv_i2c_msg *msg)
 {
        int ret;
 
@@ -160,7 +108,7 @@ int i2c_transfer(struct mv_i2c_msg *msg)
        switch (msg->direction) {
        case I2C_WRITE:
                /* check if bus is not busy */
-               if (!i2c_isr_set_cleared(0, ISR_IBB))
+               if (!i2c_isr_set_cleared(base, 0, ISR_IBB))
                        goto transfer_error_bus_busy;
 
                /* start transmission */
@@ -179,7 +127,7 @@ int i2c_transfer(struct mv_i2c_msg *msg)
                writel(readl(&base->icr) | ICR_TB, &base->icr);
 
                /* transmit register empty? */
-               if (!i2c_isr_set_cleared(ISR_ITE, 0))
+               if (!i2c_isr_set_cleared(base, ISR_ITE, 0))
                        goto transfer_error_transmit_timeout;
 
                /* clear 'transmit empty' state */
@@ -187,14 +135,14 @@ int i2c_transfer(struct mv_i2c_msg *msg)
 
                /* wait for ACK from slave */
                if (msg->acknack == I2C_ACKNAK_WAITACK)
-                       if (!i2c_isr_set_cleared(0, ISR_ACKNAK))
+                       if (!i2c_isr_set_cleared(base, 0, ISR_ACKNAK))
                                goto transfer_error_ack_missing;
                break;
 
        case I2C_READ:
 
                /* check if bus is not busy */
-               if (!i2c_isr_set_cleared(0, ISR_IBB))
+               if (!i2c_isr_set_cleared(base, 0, ISR_IBB))
                        goto transfer_error_bus_busy;
 
                /* start receive */
@@ -212,7 +160,7 @@ int i2c_transfer(struct mv_i2c_msg *msg)
                writel(readl(&base->icr) | ICR_TB, &base->icr);
 
                /* receive register full? */
-               if (!i2c_isr_set_cleared(ISR_IRF, 0))
+               if (!i2c_isr_set_cleared(base, ISR_IRF, 0))
                        goto transfer_error_receive_timeout;
 
                msg->data = readl(&base->idbr);
@@ -258,68 +206,35 @@ transfer_error_bus_busy:
 
 i2c_transfer_finish:
        debug("i2c_transfer: ISR: 0x%04x\n", readl(&base->isr));
-       i2c_reset();
+       i2c_reset(base);
        return ret;
 }
 
-/* ------------------------------------------------------------------------ */
-/* API Functions                                                            */
-/* ------------------------------------------------------------------------ */
-void i2c_init(int speed, int slaveaddr)
-{
-#ifdef CONFIG_I2C_MULTI_BUS
-       current_bus = 0;
-       base = (struct mv_i2c *)i2c_regs[current_bus];
-#else
-       base = (struct mv_i2c *)CONFIG_MV_I2C_REG;
-#endif
-
-       i2c_board_init(base);
-}
-
-/*
- * i2c_probe: - Test if a chip answers for a given i2c address
- *
- * @chip:      address of the chip which is searched for
- * @return:    0 if a chip was found, -1 otherwhise
- */
-int i2c_probe(uchar chip)
+static int __i2c_probe_chip(struct mv_i2c *base, uchar chip)
 {
        struct mv_i2c_msg msg;
 
-       i2c_reset();
+       i2c_reset(base);
 
        msg.condition = I2C_COND_START;
        msg.acknack   = I2C_ACKNAK_WAITACK;
        msg.direction = I2C_WRITE;
        msg.data      = (chip << 1) + 1;
-       if (i2c_transfer(&msg))
+       if (i2c_transfer(base, &msg))
                return -1;
 
        msg.condition = I2C_COND_STOP;
        msg.acknack   = I2C_ACKNAK_SENDNAK;
        msg.direction = I2C_READ;
        msg.data      = 0x00;
-       if (i2c_transfer(&msg))
+       if (i2c_transfer(base, &msg))
                return -1;
 
        return 0;
 }
 
-/*
- * i2c_read: - Read multiple bytes from an i2c device
- *
- * The higher level routines take into account that this function is only
- * called with len < page length of the device (see configuration file)
- *
- * @chip:      address of the chip which is to be read
- * @addr:      i2c data address within the chip
- * @alen:      length of the i2c data address (1..2 bytes)
- * @buffer:    where to write the data
- * @len:       how much byte do we want to read
- * @return:    0 in case of success
- */
-int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
+static int __i2c_read(struct mv_i2c *base, uchar chip, uint addr, int alen,
+                     uchar *buffer, int len)
 {
        struct mv_i2c_msg msg;
        u8 addr_bytes[3]; /* lowest...highest byte of data address */
@@ -327,7 +242,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
        debug("i2c_read(chip=0x%02x, addr=0x%02x, alen=0x%02x, "
              "len=0x%02x)\n", chip, addr, alen, len);
 
-       i2c_reset();
+       i2c_reset(base);
 
        /* dummy chip address write */
        debug("i2c_read: dummy chip address write\n");
@@ -336,7 +251,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
        msg.direction = I2C_WRITE;
        msg.data = (chip << 1);
        msg.data &= 0xFE;
-       if (i2c_transfer(&msg))
+       if (i2c_transfer(base, &msg))
                return -1;
 
        /*
@@ -354,7 +269,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
                msg.acknack   = I2C_ACKNAK_WAITACK;
                msg.direction = I2C_WRITE;
                msg.data      = addr_bytes[alen];
-               if (i2c_transfer(&msg))
+               if (i2c_transfer(base, &msg))
                        return -1;
        }
 
@@ -365,7 +280,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
        msg.direction = I2C_WRITE;
        msg.data      = (chip << 1);
        msg.data     |= 0x01;
-       if (i2c_transfer(&msg))
+       if (i2c_transfer(base, &msg))
                return -1;
 
        /* read bytes; send NACK at last byte */
@@ -380,7 +295,7 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
 
                msg.direction = I2C_READ;
                msg.data      = 0x00;
-               if (i2c_transfer(&msg))
+               if (i2c_transfer(base, &msg))
                        return -1;
 
                *buffer = msg.data;
@@ -389,25 +304,13 @@ int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
                buffer++;
        }
 
-       i2c_reset();
+       i2c_reset(base);
 
        return 0;
 }
 
-/*
- * i2c_write: -  Write multiple bytes to an i2c device
- *
- * The higher level routines take into account that this function is only
- * called with len < page length of the device (see configuration file)
- *
- * @chip:      address of the chip which is to be written
- * @addr:      i2c data address within the chip
- * @alen:      length of the i2c data address (1..2 bytes)
- * @buffer:    where to find the data to be written
- * @len:       how much byte do we want to read
- * @return:    0 in case of success
- */
-int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
+static int __i2c_write(struct mv_i2c *base, uchar chip, uint addr, int alen,
+                      uchar *buffer, int len)
 {
        struct mv_i2c_msg msg;
        u8 addr_bytes[3]; /* lowest...highest byte of data address */
@@ -415,7 +318,7 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
        debug("i2c_write(chip=0x%02x, addr=0x%02x, alen=0x%02x, "
              "len=0x%02x)\n", chip, addr, alen, len);
 
-       i2c_reset();
+       i2c_reset(base);
 
        /* chip address write */
        debug("i2c_write: chip address write\n");
@@ -424,7 +327,7 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
        msg.direction = I2C_WRITE;
        msg.data = (chip << 1);
        msg.data &= 0xFE;
-       if (i2c_transfer(&msg))
+       if (i2c_transfer(base, &msg))
                return -1;
 
        /*
@@ -441,7 +344,7 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
                msg.acknack   = I2C_ACKNAK_WAITACK;
                msg.direction = I2C_WRITE;
                msg.data      = addr_bytes[alen];
-               if (i2c_transfer(&msg))
+               if (i2c_transfer(base, &msg))
                        return -1;
        }
 
@@ -459,11 +362,123 @@ int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
                msg.direction = I2C_WRITE;
                msg.data      = *(buffer++);
 
-               if (i2c_transfer(&msg))
+               if (i2c_transfer(base, &msg))
                        return -1;
        }
 
-       i2c_reset();
+       i2c_reset(base);
 
        return 0;
 }
+
+static struct mv_i2c *base_glob;
+
+static void i2c_board_init(struct mv_i2c *base)
+{
+#ifdef CONFIG_SYS_I2C_INIT_BOARD
+       u32 icr;
+       /*
+        * call board specific i2c bus reset routine before accessing the
+        * environment, which might be in a chip on that bus. For details
+        * about this problem see doc/I2C_Edge_Conditions.
+        *
+        * disable I2C controller first, otherwhise it thinks we want to
+        * talk to the slave port...
+        */
+       icr = readl(&base->icr);
+       writel(readl(&base->icr) & ~(ICR_SCLE | ICR_IUE), &base->icr);
+
+       i2c_init_board();
+
+       writel(icr, &base->icr);
+#endif
+}
+
+#ifdef CONFIG_I2C_MULTI_BUS
+static unsigned long i2c_regs[CONFIG_MV_I2C_NUM] = CONFIG_MV_I2C_REG;
+static unsigned int bus_initialized[CONFIG_MV_I2C_NUM];
+static unsigned int current_bus;
+
+int i2c_set_bus_num(unsigned int bus)
+{
+       if ((bus < 0) || (bus >= CONFIG_MV_I2C_NUM)) {
+               printf("Bad bus: %d\n", bus);
+               return -1;
+       }
+
+       base_glob = (struct mv_i2c *)i2c_regs[bus];
+       current_bus = bus;
+
+       if (!bus_initialized[current_bus]) {
+               i2c_board_init(base_glob);
+               bus_initialized[current_bus] = 1;
+       }
+
+       return 0;
+}
+
+unsigned int i2c_get_bus_num(void)
+{
+       return current_bus;
+}
+#endif
+
+/* API Functions */
+void i2c_init(int speed, int slaveaddr)
+{
+#ifdef CONFIG_I2C_MULTI_BUS
+       current_bus = 0;
+       base_glob = (struct mv_i2c *)i2c_regs[current_bus];
+#else
+       base_glob = (struct mv_i2c *)CONFIG_MV_I2C_REG;
+#endif
+
+       i2c_board_init(base_glob);
+}
+
+/*
+ * i2c_probe: - Test if a chip answers for a given i2c address
+ *
+ * @chip:      address of the chip which is searched for
+ * @return:    0 if a chip was found, -1 otherwhise
+ */
+int i2c_probe(uchar chip)
+{
+       return __i2c_probe_chip(base_glob, chip);
+}
+
+/*
+ * i2c_read: - Read multiple bytes from an i2c device
+ *
+ * The higher level routines take into account that this function is only
+ * called with len < page length of the device (see configuration file)
+ *
+ * @chip:      address of the chip which is to be read
+ * @addr:      i2c data address within the chip
+ * @alen:      length of the i2c data address (1..2 bytes)
+ * @buffer:    where to write the data
+ * @len:       how much byte do we want to read
+ * @return:    0 in case of success
+ */
+int i2c_read(uchar chip, uint addr, int alen, uchar *buffer, int len)
+{
+       return __i2c_read(base_glob, chip, addr, alen, buffer, len);
+}
+
+/*
+ * i2c_write: -  Write multiple bytes to an i2c device
+ *
+ * The higher level routines take into account that this function is only
+ * called with len < page length of the device (see configuration file)
+ *
+ * @chip:      address of the chip which is to be written
+ * @addr:      i2c data address within the chip
+ * @alen:      length of the i2c data address (1..2 bytes)
+ * @buffer:    where to find the data to be written
+ * @len:       how much byte do we want to read
+ * @return:    0 in case of success
+ */
+int i2c_write(uchar chip, uint addr, int alen, uchar *buffer, int len)
+{
+       return __i2c_write(base_glob, chip, addr, alen, buffer, len);
+}