]> git.sur5r.net Git - u-boot/commitdiff
Add support for SX151x SPI GPIO Expanders
authorViktar Palstsiuk <viktar.palstsiuk@promwad.com>
Thu, 31 Oct 2013 08:16:59 +0000 (11:16 +0300)
committerTom Rini <trini@ti.com>
Fri, 8 Nov 2013 14:39:13 +0000 (09:39 -0500)
Signed-off-by: Viktar Palstsiuk <viktar.palstsiuk@promwad.com>
drivers/gpio/Makefile
drivers/gpio/sx151x.c [new file with mode: 0644]
include/sx151x.h [new file with mode: 0644]

index 1165793b5e8bd48d3bc6e96a7fbe3e2e05a21a2f..b903c45c5249fe0e67f289fba4f788bc63f471c8 100644 (file)
@@ -30,3 +30,4 @@ obj-$(CONFIG_S3C2440_GPIO)    += s3c2440_gpio.o
 obj-$(CONFIG_XILINX_GPIO)      += xilinx_gpio.o
 obj-$(CONFIG_ADI_GPIO2)        += adi_gpio2.o
 obj-$(CONFIG_TCA642X)          += tca642x.o
+oby-$(CONFIG_SX151X)           += sx151x.o
diff --git a/drivers/gpio/sx151x.c b/drivers/gpio/sx151x.c
new file mode 100644 (file)
index 0000000..167cf40
--- /dev/null
@@ -0,0 +1,242 @@
+/*
+ * (C) Copyright 2013
+ * Viktar Palstsiuk, Promwad, viktar.palstsiuk@promwad.com
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+/*
+ * Driver for Semtech SX151x SPI GPIO Expanders
+ */
+
+#include <common.h>
+#include <spi.h>
+#include <sx151x.h>
+
+#ifndef CONFIG_SX151X_SPI_BUS
+#define CONFIG_SX151X_SPI_BUS 0
+#endif
+
+/*
+ * The SX151x registers
+ */
+
+#ifdef CONFIG_SX151X_GPIO_COUNT_8
+/* 8bit: SX1511 */
+#define SX151X_REG_DIR         0x07
+#define SX151X_REG_DATA                0x08
+#else
+/* 16bit: SX1512 */
+#define SX151X_REG_DIR         0x0F
+#define SX151X_REG_DATA                0x11
+#endif
+#define SX151X_REG_RESET       0x7D
+
+static int sx151x_spi_write(int chip, unsigned char reg, unsigned char val)
+{
+       struct spi_slave *slave;
+       unsigned char buf[2];
+       int ret;
+
+       slave = spi_setup_slave(CONFIG_SX151X_SPI_BUS, chip, 1000000,
+                               SPI_MODE_0);
+       if (!slave)
+               return 0;
+
+       spi_claim_bus(slave);
+
+       buf[0] = reg;
+       buf[1] = val;
+
+       ret = spi_xfer(slave, 16, buf, NULL, SPI_XFER_BEGIN | SPI_XFER_END);
+       if (ret < 0)
+               printf("spi%d.%d write fail: can't write %02x to %02x: %d\n",
+                       CONFIG_SX151X_SPI_BUS, chip, val, reg, ret);
+       else
+               printf("spi%d.%d write 0x%02x to register 0x%02x\n",
+                      CONFIG_SX151X_SPI_BUS, chip, val, reg);
+       spi_release_bus(slave);
+       spi_free_slave(slave);
+
+       return ret;
+}
+
+static int sx151x_spi_read(int chip, unsigned char reg)
+{
+       struct spi_slave *slave;
+       int ret;
+
+       slave = spi_setup_slave(CONFIG_SX151X_SPI_BUS, chip, 1000000,
+                               SPI_MODE_0);
+       if (!slave)
+               return 0;
+
+       spi_claim_bus(slave);
+
+       ret = spi_w8r8(slave, reg | 0x80);
+       if (ret < 0)
+               printf("spi%d.%d read fail: can't read %02x: %d\n",
+                       CONFIG_SX151X_SPI_BUS, chip, reg, ret);
+       else
+               printf("spi%d.%d read register 0x%02x: 0x%02x\n",
+                      CONFIG_SX151X_SPI_BUS, chip, reg, ret);
+
+       spi_release_bus(slave);
+       spi_free_slave(slave);
+
+       return ret;
+}
+
+static inline void sx151x_find_cfg(int gpio, unsigned char *reg, unsigned char *mask)
+{
+       *reg   -= gpio / 8;
+       *mask   = 1 << (gpio % 8);
+}
+
+static int sx151x_write_cfg(int chip, unsigned char gpio, unsigned char reg, int val)
+{
+       unsigned char  mask;
+       unsigned char  data;
+       int ret;
+
+       sx151x_find_cfg(gpio, &reg, &mask);
+       ret = sx151x_spi_read(chip, reg);
+       if (ret < 0)
+               return ret;
+       else
+               data = ret;
+       data &= ~mask;
+       data |= (val << (gpio % 8)) & mask;
+       return sx151x_spi_write(chip, reg, data);
+}
+
+int sx151x_get_value(int chip, int gpio)
+{
+       unsigned char  reg = SX151X_REG_DATA;
+       unsigned char  mask;
+       int ret;
+
+       sx151x_find_cfg(gpio, &reg, &mask);
+       ret = sx151x_spi_read(chip, reg);
+       if (ret >= 0)
+               ret = (ret & mask) != 0 ? 1 : 0;
+
+       return ret;
+}
+
+int sx151x_set_value(int chip, int gpio, int val)
+{
+       return sx151x_write_cfg(chip, gpio, SX151X_REG_DATA, (val ? 1 : 0));
+}
+
+int sx151x_direction_input(int chip, int gpio)
+{
+       return sx151x_write_cfg(chip, gpio, SX151X_REG_DIR, 1);
+}
+
+int sx151x_direction_output(int chip, int gpio)
+{
+       return sx151x_write_cfg(chip, gpio, SX151X_REG_DIR, 0);
+}
+
+int sx151x_reset(int chip)
+{
+       int err;
+
+       err = sx151x_spi_write(chip, SX151X_REG_RESET, 0x12);
+       if (err < 0)
+               return err;
+
+       err = sx151x_spi_write(chip, SX151X_REG_RESET, 0x34);
+       return err;
+}
+
+#ifdef CONFIG_CMD_SX151X
+
+int do_sx151x(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+       int ret = CMD_RET_USAGE, chip = 0, gpio = 0, val = 0;
+
+       if (argc < 3)
+               return CMD_RET_USAGE;
+
+       /* arg2 used as chip number */
+       chip = simple_strtoul(argv[2], NULL, 10);
+
+       if (strcmp(argv[1], "reset") == 0) {
+               ret = sx151x_reset(chip);
+               if (!ret) {
+                       printf("Device at spi%d.%d was reset\n",
+                              CONFIG_SX151X_SPI_BUS, chip);
+               }
+               return ret;
+       }
+
+       if (argc < 4)
+               return CMD_RET_USAGE;
+
+       /* arg3 used as gpio number */
+       gpio = simple_strtoul(argv[3], NULL, 10);
+
+       if (strcmp(argv[1], "get") == 0) {
+               ret = sx151x_get_value(chip, gpio);
+               if (ret < 0)
+                       printf("Failed to get value at spi%d.%d gpio %d\n",
+                              CONFIG_SX151X_SPI_BUS, chip, gpio);
+               else {
+                       printf("Value at spi%d.%d gpio %d is %d\n",
+                              CONFIG_SX151X_SPI_BUS, chip, gpio, ret);
+                       ret = 0;
+               }
+               return ret;
+       }
+
+       if (argc < 5)
+               return CMD_RET_USAGE;
+
+       /* arg4 used as value or direction */
+       val = simple_strtoul(argv[4], NULL, 10);
+
+       if (strcmp(argv[1], "set") == 0) {
+               ret = sx151x_set_value(chip, gpio, val);
+               if (ret < 0)
+                       printf("Failed to set value at spi%d.%d gpio %d\n",
+                              CONFIG_SX151X_SPI_BUS, chip, gpio);
+               else
+                       printf("New value at spi%d.%d gpio %d is %d\n",
+                              CONFIG_SX151X_SPI_BUS, chip, gpio, val);
+               return ret;
+       } else if (strcmp(argv[1], "dir") == 0) {
+               if (val == 0)
+                       ret = sx151x_direction_output(chip, gpio);
+               else
+                       ret = sx151x_direction_input(chip, gpio);
+
+               if (ret < 0)
+                       printf("Failed to set direction of spi%d.%d gpio %d\n",
+                              CONFIG_SX151X_SPI_BUS, chip, gpio);
+               else
+                       printf("New direction of spi%d.%d gpio %d is %d\n",
+                              CONFIG_SX151X_SPI_BUS, chip, gpio, val);
+               return ret;
+       }
+
+       printf("Please see usage\n");
+
+       return ret;
+}
+
+U_BOOT_CMD(
+       sx151x, 5,      1,      do_sx151x,
+       "sx151x gpio access",
+       "dir chip gpio 0|1\n"
+       "       - set gpio direction (0 for output, 1 for input)\n"
+       "sx151x get chip gpio\n"
+       "       - get gpio value\n"
+       "sx151x set chip gpio 0|1\n"
+       "       - set gpio value\n"
+       "sx151x reset chip\n"
+       "       - reset chip"
+);
+
+#endif /* CONFIG_CMD_SX151X */
diff --git a/include/sx151x.h b/include/sx151x.h
new file mode 100644 (file)
index 0000000..be42b06
--- /dev/null
@@ -0,0 +1,17 @@
+/*
+ * (C) Copyright 2013
+ * Viktar Palstsiuk, Promwad, viktar.palstsiuk@promwad.com
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#ifndef __SX151X_H_
+#define __SX151X_H_
+
+int sx151x_get_value(int chip, int gpio);
+int sx151x_set_value(int chip, int gpio, int val);
+int sx151x_direction_input(int chip, int gpio);
+int sx151x_direction_output(int chip, int gpio);
+int sx151x_reset(int chip);
+
+#endif /* __SX151X_H_ */