+++ /dev/null
-/* keyboard/mouse not implemented yet */
-
-extern int cma_kbm_not_implemented;
-
-/**************** DEFINES for H8542B Keyboard/Mouse Controller ***************/
-
-/*
- * note the auxillary port is used to control the mouse
- */
-
-/* 8542B Commands (Sent to the Command Port) */
-#define HT8542_CMD_SET_BYTE 0x60 /* Set the command byte */
-#define HT8542_CMD_GET_BYTE 0x20 /* Get the command byte */
-#define HT8542_CMD_KBD_OBUFF 0xD2 /* Write to HT8542 Kbd Output Buffer */
-#define HT8542_CMD_AUX_OBUFF 0xD3 /* Write to HT8542 Mse Output Buffer */
-#define HT8542_CMD_AUX_WRITE 0xD4 /* Write to Mouse Port */
-#define HT8542_CMD_AUX_OFF 0xA7 /* Disable Mouse Port */
-#define HT8542_CMD_AUX_ON 0xA8 /* Re-Enable Mouse Port */
-#define HT8542_CMD_AUX_TEST 0xA9 /* Test for the presence of a Mouse */
-#define HT8542_CMD_DIAG 0xAA /* Start Diagnostics */
-#define HT8542_CMD_KBD_TEST 0xAB /* Test for presence of a keyboard */
-#define HT8542_CMD_KBD_OFF 0xAD /* Disable Kbd Port (use KBD_DAT_ON) */
-#define HT8542_CMD_KBD_ON 0xAE /* Enable Kbd Port (use KBD_DAT_OFF) */
-
-/* HT8542B cmd byte set by KBD_CMD_SET_BYTE and retrieved by KBD_CMD_GET_BYTE */
-#define HT8542_CMD_BYTE_TRANS 0x40
-#define HT8542_CMD_BYTE_AUX_OFF 0x20 /* 1 = mse port disabled, 0 = enabled */
-#define HT8542_CMD_BYTE_KBD_OFF 0x10 /* 1 = kbd port disabled, 0 = enabled */
-#define HT8542_CMD_BYTE_OVER 0x08 /* 1 = override keyboard lock */
-#define HT8542_CMD_BYTE_RES 0x04 /* reserved */
-#define HT8542_CMD_BYTE_AUX_INT 0x02 /* 1 = enable mouse interrupt */
-#define HT8542_CMD_BYTE_KBD_INT 0x01 /* 1 = enable keyboard interrupt */
-
-/* Keyboard Commands (Sent to the Data Port) */
-#define KBD_CMD_LED 0xED /* Set Keyboard LEDS with next byte */
-#define KBD_CMD_ECHO 0xEE /* Echo - we get 0xFA, 0xEE back */
-#define KBD_CMD_MODE 0xF0 /* set scan code mode with next byte */
-#define KBD_CMD_ID 0xF2 /* get keyboard/mouse ID */
-#define KBD_CMD_RPT 0xF3 /* Set Repeat Rate and Delay 2nd Byte */
-#define KBD_CMD_ON 0xF4 /* Enable keyboard */
-#define KBD_CMD_OFF 0xF5 /* Disables Scanning, Resets to Def */
-#define KBD_CMD_DEF 0xF6 /* Reverts kbd to default settings */
-#define KBD_CMD_RST 0xFF /* Reset - should get 0xFA, 0xAA back */
-
-/* Set LED second bit defines */
-#define KBD_CMD_LED_SCROLL 0x01 /* Set SCROLL LOCK LED on */
-#define KBD_CMD_LED_NUM 0x02 /* Set NUM LOCK LED on */
-#define KBD_CMD_LED_CAPS 0x04 /* Set CAPS LOCK LED on */
-
-/* Set Mode second byte defines */
-#define KBD_CMD_MODE_STAT 0x00 /* get current scan code mode */
-#define KBD_CMD_MODE_SCAN1 0x01 /* set mode to scan code 1 */
-#define KBD_CMD_MODE_SCAN2 0x02 /* set mode to scan code 2 */
-#define KBD_CMD_MODE_SCAN3 0x03 /* set mode to scan code 3 */
-
-/* Keyboard/Mouse ID Codes */
-#define KBD_CMD_ID_1ST 0xAB /* 1st byte is 0xAB, 2nd is actual ID */
-#define KBD_CMD_ID_KBD 0x83 /* Keyboard */
-#define KBD_CMD_ID_MOUSE 0x00 /* Mouse */
-
-/* Keyboard Data Return Defines */
-#define KBD_STAT_OVER 0x00 /* Buffer Overrun */
-#define KBD_STAT_DIAG_OK 0x55 /* Internal Self Test OK */
-#define KBD_STAT_RST_OK 0xAA /* Reset Complete */
-#define KBD_STAT_ECHO 0xEE /* Echo Command Return */
-#define KBD_STAT_BRK 0xF0 /* Prefix for Break Key Code */
-#define KBD_STAT_ACK 0xFA /* Received after all commands */
-#define KBD_STAT_DIAG_FAIL 0xFD /* Internal Self Test Failed */
-#define KBD_STAT_RESEND 0xFE /* Resend Last Command */
-
-/* HT8542B Status Register Bit Defines */
-#define HT8542_STAT_OBF 0x01 /* 1 = output buffer is full */
-#define HT8542_STAT_IBF 0x02 /* 1 = input buffer is full */
-#define HT8542_STAT_SYS 0x04 /* system flag - unused */
-#define HT8542_STAT_CMD 0x08 /* 1 = cmd in input buffer, 0 = data */
-#define HT8542_STAT_INH 0x10 /* 1 = Inhibit - unused */
-#define HT8542_STAT_TX 0x20 /* 1 = Transmit Timeout has occured */
-#define HT8542_STAT_RX 0x40 /* 1 = Receive Timeout has occured */
-#define HT8542_STAT_PERR 0x80 /* 1 = Parity Error from Keyboard */
+++ /dev/null
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/****************************************************************************
- * FLASH Memory Map as used by CRAY L1, 4MB AMD29F032B flash chip
- *
- * Start Address Length
- * +++++++++++++++++++++++++ 0xFFC0_0000 Start of Flash -----------------
- * | Failsafe Linux Image | (1M)
- * +=======================+ 0xFFD0_0000
- * | (Reserved FlashFiles) | (1M)
- * +=======================+ 0xFFE0_0000
- * | Failsafe RootFS | (1M)
- * +=======================+ 0xFFF0_0000
- * | |
- * | U N U S E D |
- * | |
- * +-----------------------+ 0xFFFD_0000 U-Boot image header (64 bytes)
- * | environment settings | (64k)
- * +-----------------------+ 0xFFFE_0000 U-Boot image header (64 bytes)
- * | U-Boot | 0xFFFE_0040 _start of U-Boot
- * | | 0xFFFE_FFFC reset vector - branch to _start
- * +++++++++++++++++++++++++ 0xFFFF_FFFF End of Flash -----------------
- *****************************************************************************/
+++ /dev/null
-/*
- * Copyright (c) 2000,2001 Epson Research and Development, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
- *
- * File generated by S1D13806CFG.EXE
- * Panel: (active) 640x480 59Hz TFT Single 18-bit (PCLK=CLKI2=25.000MHz)
- * Memory: Embedded SDRAM (MCLK=CLKI=49.152MHz) (BUSCLK=33.333MHz)
- */
-
-static S1D_REGS regs_13806_640_320_16bpp[] =
-{
- {0x0001,0x00}, /* Miscellaneous Register */
- {0x01FC,0x00}, /* Display Mode Register */
- {0x0004,0x18}, /* General IO Pins Configuration Register 0 */
- {0x0005,0x00}, /* General IO Pins Configuration Register 1 */
- {0x0008,0x18}, /* General IO Pins Control Register 0 */
- {0x0009,0x00}, /* General IO Pins Control Register 1 */
- {0x0010,0x00}, /* Memory Clock Configuration Register */
- {0x0014,0x02}, /* LCD Pixel Clock Configuration Register */
- {0x0018,0x02}, /* CRT/TV Pixel Clock Configuration Register */
- {0x001C,0x02}, /* MediaPlug Clock Configuration Register */
- {0x001E,0x01}, /* CPU To Memory Wait State Select Register */
- {0x0021,0x03}, /* DRAM Refresh Rate Register */
- {0x002A,0x00}, /* DRAM Timings Control Register 0 */
- {0x002B,0x01}, /* DRAM Timings Control Register 1 */
- {0x0020,0x80}, /* Memory Configuration Register */
- {0x0030,0x25}, /* Panel Type Register */
- {0x0031,0x00}, /* MOD Rate Register */
- {0x0032,0x4F}, /* LCD Horizontal Display Width Register */
- {0x0034,0x13}, /* LCD Horizontal Non-Display Period Register */
- {0x0035,0x00}, /* TFT FPLINE Start Position Register */
- {0x0036,0x0B}, /* TFT FPLINE Pulse Width Register */
- {0x0038,0xDF}, /* LCD Vertical Display Height Register 0 */
- {0x0039,0x01}, /* LCD Vertical Display Height Register 1 */
- {0x003A,0x24}, /* LCD Vertical Non-Display Period Register */
- {0x003B,0x00}, /* TFT FPFRAME Start Position Register */
- {0x003C,0x01}, /* TFT FPFRAME Pulse Width Register */
- {0x0040,0x03}, /* LCD Display Mode Register (8bpp) */
- {0x0041,0x00}, /* LCD Miscellaneous Register */
- {0x0042,0x00}, /* LCD Display Start Address Register 0 */
- {0x0043,0x00}, /* LCD Display Start Address Register 1 */
- {0x0044,0x00}, /* LCD Display Start Address Register 2 */
- {0x0046,0x80}, /* LCD Memory Address Offset Register 0 */
- {0x0047,0x02}, /* LCD Memory Address Offset Register 1 */
- {0x0048,0x00}, /* LCD Pixel Panning Register */
- {0x004A,0x00}, /* LCD Display FIFO High Threshold Control Register */
- {0x004B,0x00}, /* LCD Display FIFO Low Threshold Control Register */
- {0x0050,0x4F}, /* CRT/TV Horizontal Display Width Register */
- {0x0052,0x13}, /* CRT/TV Horizontal Non-Display Period Register */
- {0x0053,0x01}, /* CRT/TV HRTC Start Position Register */
- {0x0054,0x0B}, /* CRT/TV HRTC Pulse Width Register */
- {0x0056,0xDF}, /* CRT/TV Vertical Display Height Register 0 */
- {0x0057,0x01}, /* CRT/TV Vertical Display Height Register 1 */
- {0x0058,0x2B}, /* CRT/TV Vertical Non-Display Period Register */
- {0x0059,0x09}, /* CRT/TV VRTC Start Position Register */
- {0x005A,0x01}, /* CRT/TV VRTC Pulse Width Register */
- {0x005B,0x10}, /* TV Output Control Register */
- {0x0060,0x05}, /* CRT/TV Display Mode Register */
- {0x0062,0x00}, /* CRT/TV Display Start Address Register 0 */
- {0x0063,0x00}, /* CRT/TV Display Start Address Register 1 */
- {0x0064,0x00}, /* CRT/TV Display Start Address Register 2 */
- {0x0066,0x80}, /* CRT/TV Memory Address Offset Register 0 */
- {0x0067,0x02}, /* CRT/TV Memory Address Offset Register 1 */
- {0x0068,0x00}, /* CRT/TV Pixel Panning Register */
- {0x006A,0x00}, /* CRT/TV Display FIFO High Threshold Control Register */
- {0x006B,0x00}, /* CRT/TV Display FIFO Low Threshold Control Register */
- {0x0070,0x00}, /* LCD Ink/Cursor Control Register */
- {0x0071,0x01}, /* LCD Ink/Cursor Start Address Register */
- {0x0072,0x00}, /* LCD Cursor X Position Register 0 */
- {0x0073,0x00}, /* LCD Cursor X Position Register 1 */
- {0x0074,0x00}, /* LCD Cursor Y Position Register 0 */
- {0x0075,0x00}, /* LCD Cursor Y Position Register 1 */
- {0x0076,0x00}, /* LCD Ink/Cursor Blue Color 0 Register */
- {0x0077,0x00}, /* LCD Ink/Cursor Green Color 0 Register */
- {0x0078,0x00}, /* LCD Ink/Cursor Red Color 0 Register */
- {0x007A,0x1F}, /* LCD Ink/Cursor Blue Color 1 Register */
- {0x007B,0x3F}, /* LCD Ink/Cursor Green Color 1 Register */
- {0x007C,0x1F}, /* LCD Ink/Cursor Red Color 1 Register */
- {0x007E,0x00}, /* LCD Ink/Cursor FIFO Threshold Register */
- {0x0080,0x00}, /* CRT/TV Ink/Cursor Control Register */
- {0x0081,0x01}, /* CRT/TV Ink/Cursor Start Address Register */
- {0x0082,0x00}, /* CRT/TV Cursor X Position Register 0 */
- {0x0083,0x00}, /* CRT/TV Cursor X Position Register 1 */
- {0x0084,0x00}, /* CRT/TV Cursor Y Position Register 0 */
- {0x0085,0x00}, /* CRT/TV Cursor Y Position Register 1 */
- {0x0086,0x00}, /* CRT/TV Ink/Cursor Blue Color 0 Register */
- {0x0087,0x00}, /* CRT/TV Ink/Cursor Green Color 0 Register */
- {0x0088,0x00}, /* CRT/TV Ink/Cursor Red Color 0 Register */
- {0x008A,0x1F}, /* CRT/TV Ink/Cursor Blue Color 1 Register */
- {0x008B,0x3F}, /* CRT/TV Ink/Cursor Green Color 1 Register */
- {0x008C,0x1F}, /* CRT/TV Ink/Cursor Red Color 1 Register */
- {0x008E,0x00}, /* CRT/TV Ink/Cursor FIFO Threshold Register */
- {0x0100,0x00}, /* BitBlt Control Register 0 */
- {0x0101,0x00}, /* BitBlt Control Register 1 */
- {0x0102,0x00}, /* BitBlt ROP Code/Color Expansion Register */
- {0x0103,0x00}, /* BitBlt Operation Register */
- {0x0104,0x00}, /* BitBlt Source Start Address Register 0 */
- {0x0105,0x00}, /* BitBlt Source Start Address Register 1 */
- {0x0106,0x00}, /* BitBlt Source Start Address Register 2 */
- {0x0108,0x00}, /* BitBlt Destination Start Address Register 0 */
- {0x0109,0x00}, /* BitBlt Destination Start Address Register 1 */
- {0x010A,0x00}, /* BitBlt Destination Start Address Register 2 */
- {0x010C,0x00}, /* BitBlt Memory Address Offset Register 0 */
- {0x010D,0x00}, /* BitBlt Memory Address Offset Register 1 */
- {0x0110,0x00}, /* BitBlt Width Register 0 */
- {0x0111,0x00}, /* BitBlt Width Register 1 */
- {0x0112,0x00}, /* BitBlt Height Register 0 */
- {0x0113,0x00}, /* BitBlt Height Register 1 */
- {0x0114,0x00}, /* BitBlt Background Color Register 0 */
- {0x0115,0x00}, /* BitBlt Background Color Register 1 */
- {0x0118,0x00}, /* BitBlt Foreground Color Register 0 */
- {0x0119,0x00}, /* BitBlt Foreground Color Register 1 */
- {0x01E0,0x00}, /* Look-Up Table Mode Register */
- {0x01E2,0x00}, /* Look-Up Table Address Register */
- {0x01F0,0x10}, /* Power Save Configuration Register */
- {0x01F1,0x00}, /* Power Save Status Register */
- {0x01F4,0x00}, /* CPU-to-Memory Access Watchdog Timer Register */
- {0x01FC,0x01}, /* Display Mode Register */
-};
+++ /dev/null
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*-----------------------------------------------------------------------
- * Timer value for timer 2, ICLK = 10
- *
- * SPEED_FCOUNT2 = GCLK / (16 * (TIMER_TMR_PS + 1))
- * SPEED_TMR3_PS = (GCLK / (16 * SPEED_FCOUNT3)) - 1
- *
- * SPEED_FCOUNT2 timer 2 counting frequency
- * GCLK CPU clock
- * SPEED_TMR2_PS prescaler
- */
-#define SPEED_TMR2_PS (250 - 1) /* divide by 250 */
-
-/*-----------------------------------------------------------------------
- * Timer value for PIT
- *
- * PIT_TIME = SPEED_PITC / PITRTCLK
- * PITRTCLK = 8192
- */
-#define SPEED_PITC (82 << 16) /* start counting from 82 */
-
-/*
- * The new value for PTA is calculated from
- *
- * PTA = (gclk * Trefresh) / (2 ^ (2 * DFBRG) * PTP * NCS)
- *
- * gclk CPU clock (not bus clock !)
- * Trefresh Refresh cycle * 4 (four word bursts used)
- * DFBRG For normal mode (no clock reduction) always 0
- * PTP Prescaler (already adjusted for no. of banks and 4K / 8K refresh)
- * NCS Number of SDRAM banks (chip selects) on this UPM.
- */
+++ /dev/null
-/*
- * The GENIETV is using the following physical memorymap (copied from
- * the FADS configuration):
- *
- * ff020000 -> ff02ffff : pcmcia
- * ff010000 -> ff01ffff : BCSR connected to CS1, setup by 8xxROM
- * ff000000 -> ff00ffff : IMAP internal in the cpu
- * 02800000 -> 0287ffff : flash connected to CS0
- * 00000000 -> nnnnnnnn : sdram setup by U-Boot
- *
- * CS pins are connected as follows:
- *
- * CS0 -512Kb boot flash
- * CS1 - SDRAM #1
- * CS2 - SDRAM #2
- * CS3 - Flash #1
- * CS4 - Flash #2
- * CS5 - LON (if present)
- * CS6 - PCMCIA #1
- * CS7 - PCMCIA #2
- *
- * Ports are configured as follows:
- *
- * PA7 - SDRAM banks enable
- */
+++ /dev/null
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*-----------------------------------------------------------------------
- * Timer value for timer 2, ICLK = 10
- *
- * SPEED_FCOUNT2 = GCLK / (16 * (TIMER_TMR_PS + 1))
- * SPEED_TMR3_PS = (GCLK / (16 * SPEED_FCOUNT3)) - 1
- *
- * SPEED_FCOUNT2 timer 2 counting frequency
- * GCLK CPU clock
- * SPEED_TMR2_PS prescaler
- */
-#define SPEED_TMR2_PS (250 - 1) /* divide by 250 */
-
-/*-----------------------------------------------------------------------
- * Timer value for PIT
- *
- * PIT_TIME = SPEED_PITC / PITRTCLK
- * PITRTCLK = 8192
- */
-#define SPEED_PITC (82 << 16) /* start counting from 82 */
-
-/*
- * The new value for PTA is calculated from
- *
- * PTA = (gclk * Trefresh) / (2 ^ (2 * DFBRG) * PTP * NCS)
- *
- * gclk CPU clock (not bus clock !)
- * Trefresh Refresh cycle * 4 (four word bursts used)
- * DFBRG For normal mode (no clock reduction) always 0
- * PTP Prescaler (already adjusted for no. of banks and 4K / 8K refresh)
- * NCS Number of SDRAM banks (chip selects) on this UPM.
- */
+++ /dev/null
-/*
- * Copyright (C) 2007 Semihalf
- * Written by Marian Balakowicz <m8@semihalf.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#define SDRAM_DDR 1 /* is DDR */
-
-/* Settings for XLB = 132 MHz */
-#define SDRAM_MODE 0x018D0000
-#define SDRAM_EMODE 0x40090000
-#define SDRAM_CONTROL 0x714F0F00
-#define SDRAM_CONFIG1 0x73711930
-#define SDRAM_CONFIG2 0x46770000
-#define SDRAM_TAPDELAY 0x10000000
+++ /dev/null
-/*
- * (C) Copyright 2003
- * Ingo Assmus <ingo.assmus@keymile.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * BK Id: SCCS/s.errno.h 1.9 06/05/01 21:45:21 paulus
- */
-#ifndef _MV_PPC_ERRNO_H
-#define _MV_PPC_ERRNO_H
-
-#define EPERM 1 /* Operation not permitted */
-#define ENOENT 2 /* No such file or directory */
-#define ESRCH 3 /* No such process */
-#define EINTR 4 /* Interrupted system call */
-#define EIO 5 /* I/O error */
-#define ENXIO 6 /* No such device or address */
-#define E2BIG 7 /* Arg list too long */
-#define ENOEXEC 8 /* Exec format error */
-#define EBADF 9 /* Bad file number */
-#define ECHILD 10 /* No child processes */
-#define EAGAIN 11 /* Try again */
-#define ENOMEM 12 /* Out of memory */
-#define EACCES 13 /* Permission denied */
-#define EFAULT 14 /* Bad address */
-#define ENOTBLK 15 /* Block device required */
-#define EBUSY 16 /* Device or resource busy */
-#define EEXIST 17 /* File exists */
-#define EXDEV 18 /* Cross-device link */
-#define ENODEV 19 /* No such device */
-#define ENOTDIR 20 /* Not a directory */
-#define EISDIR 21 /* Is a directory */
-#define EINVAL 22 /* Invalid argument */
-#define ENFILE 23 /* File table overflow */
-#define EMFILE 24 /* Too many open files */
-#define ENOTTY 25 /* Not a typewriter */
-#define ETXTBSY 26 /* Text file busy */
-#define EFBIG 27 /* File too large */
-#define ENOSPC 28 /* No space left on device */
-#define ESPIPE 29 /* Illegal seek */
-#define EROFS 30 /* Read-only file system */
-#define EMLINK 31 /* Too many links */
-#define EPIPE 32 /* Broken pipe */
-#define EDOM 33 /* Math argument out of domain of func */
-#define ERANGE 34 /* Math result not representable */
-#define EDEADLK 35 /* Resource deadlock would occur */
-#define ENAMETOOLONG 36 /* File name too long */
-#define ENOLCK 37 /* No record locks available */
-#define ENOSYS 38 /* Function not implemented */
-#define ENOTEMPTY 39 /* Directory not empty */
-#define ELOOP 40 /* Too many symbolic links encountered */
-#define EWOULDBLOCK EAGAIN /* Operation would block */
-#define ENOMSG 42 /* No message of desired type */
-#define EIDRM 43 /* Identifier removed */
-#define ECHRNG 44 /* Channel number out of range */
-#define EL2NSYNC 45 /* Level 2 not synchronized */
-#define EL3HLT 46 /* Level 3 halted */
-#define EL3RST 47 /* Level 3 reset */
-#define ELNRNG 48 /* Link number out of range */
-#define EUNATCH 49 /* Protocol driver not attached */
-#define ENOCSI 50 /* No CSI structure available */
-#define EL2HLT 51 /* Level 2 halted */
-#define EBADE 52 /* Invalid exchange */
-#define EBADR 53 /* Invalid request descriptor */
-#define EXFULL 54 /* Exchange full */
-#define ENOANO 55 /* No anode */
-#define EBADRQC 56 /* Invalid request code */
-#define EBADSLT 57 /* Invalid slot */
-#define EDEADLOCK 58 /* File locking deadlock error */
-#define EBFONT 59 /* Bad font file format */
-#define ENOSTR 60 /* Device not a stream */
-#define ENODATA 61 /* No data available */
-#define ETIME 62 /* Timer expired */
-#define ENOSR 63 /* Out of streams resources */
-#define ENONET 64 /* Machine is not on the network */
-#define ENOPKG 65 /* Package not installed */
-#define EREMOTE 66 /* Object is remote */
-#define ENOLINK 67 /* Link has been severed */
-#define EADV 68 /* Advertise error */
-#define ESRMNT 69 /* Srmount error */
-#define ECOMM 70 /* Communication error on send */
-#define EPROTO 71 /* Protocol error */
-#define EMULTIHOP 72 /* Multihop attempted */
-#define EDOTDOT 73 /* RFS specific error */
-#define EBADMSG 74 /* Not a data message */
-#define EOVERFLOW 75 /* Value too large for defined data type */
-#define ENOTUNIQ 76 /* Name not unique on network */
-#define EBADFD 77 /* File descriptor in bad state */
-#define EREMCHG 78 /* Remote address changed */
-#define ELIBACC 79 /* Can not access a needed shared library */
-#define ELIBBAD 80 /* Accessing a corrupted shared library */
-#define ELIBSCN 81 /* .lib section in a.out corrupted */
-#define ELIBMAX 82 /* Attempting to link in too many shared libraries */
-#define ELIBEXEC 83 /* Cannot exec a shared library directly */
-#define EILSEQ 84 /* Illegal byte sequence */
-#define ERESTART 85 /* Interrupted system call should be restarted */
-#define ESTRPIPE 86 /* Streams pipe error */
-#define EUSERS 87 /* Too many users */
-#define ENOTSOCK 88 /* Socket operation on non-socket */
-#define EDESTADDRREQ 89 /* Destination address required */
-#define EMSGSIZE 90 /* Message too long */
-#define EPROTOTYPE 91 /* Protocol wrong type for socket */
-#define ENOPROTOOPT 92 /* Protocol not available */
-#define EPROTONOSUPPORT 93 /* Protocol not supported */
-#define ESOCKTNOSUPPORT 94 /* Socket type not supported */
-#define EOPNOTSUPP 95 /* Operation not supported on transport endpoint */
-#define EPFNOSUPPORT 96 /* Protocol family not supported */
-#define EAFNOSUPPORT 97 /* Address family not supported by protocol */
-#define EADDRINUSE 98 /* Address already in use */
-#define EADDRNOTAVAIL 99 /* Cannot assign requested address */
-#define ENETDOWN 100 /* Network is down */
-#define ENETUNREACH 101 /* Network is unreachable */
-#define ENETRESET 102 /* Network dropped connection because of reset */
-#define ECONNABORTED 103 /* Software caused connection abort */
-#define ECONNRESET 104 /* Connection reset by peer */
-#define ENOBUFS 105 /* No buffer space available */
-#define EISCONN 106 /* Transport endpoint is already connected */
-#define ENOTCONN 107 /* Transport endpoint is not connected */
-#define ESHUTDOWN 108 /* Cannot send after transport endpoint shutdown */
-#define ETOOMANYREFS 109 /* Too many references: cannot splice */
-#define ETIMEDOUT 110 /* Connection timed out */
-#define ECONNREFUSED 111 /* Connection refused */
-#define EHOSTDOWN 112 /* Host is down */
-#define EHOSTUNREACH 113 /* No route to host */
-#define EALREADY 114 /* Operation already in progress */
-#define EINPROGRESS 115 /* Operation now in progress */
-#define ESTALE 116 /* Stale NFS file handle */
-#define EUCLEAN 117 /* Structure needs cleaning */
-#define ENOTNAM 118 /* Not a XENIX named type file */
-#define ENAVAIL 119 /* No XENIX semaphores available */
-#define EISNAM 120 /* Is a named type file */
-#define EREMOTEIO 121 /* Remote I/O error */
-#define EDQUOT 122 /* Quota exceeded */
-
-#define ENOMEDIUM 123 /* No medium found */
-#define EMEDIUMTYPE 124 /* Wrong medium type */
-
-/* Should never be seen by user programs */
-#define ERESTARTSYS 512
-#define ERESTARTNOINTR 513
-#define ERESTARTNOHAND 514 /* restart if no handler.. */
-#define ENOIOCTLCMD 515 /* No ioctl command */
-
-#define _LAST_ERRNO 515
-
-#endif
+++ /dev/null
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*-----------------------------------------------------------------------
- * Timer value for timer 2, ICLK = 10
- *
- * SPEED_FCOUNT2 = GCLK / (16 * (TIMER_TMR_PS + 1))
- * SPEED_TMR3_PS = (GCLK / (16 * SPEED_FCOUNT3)) - 1
- *
- * SPEED_FCOUNT2 timer 2 counting frequency
- * GCLK CPU clock
- * SPEED_TMR2_PS prescaler
- */
-#define SPEED_TMR2_PS (250 - 1) /* divide by 250 */
-
-/*-----------------------------------------------------------------------
- * Timer value for PIT
- *
- * PIT_TIME = SPEED_PITC / PITRTCLK
- * PITRTCLK = 8192
- */
-#define SPEED_PITC (82 << 16) /* start counting from 82 */
-
-/*
- * The new value for PTA is calculated from
- *
- * PTA = (gclk * Trefresh) / (2 ^ (2 * DFBRG) * PTP * NCS)
- *
- * gclk CPU clock (not bus clock !)
- * Trefresh Refresh cycle * 4 (four word bursts used)
- * DFBRG For normal mode (no clock reduction) always 0
- * PTP Prescaler (already adjusted for no. of banks and 4K / 8K refresh)
- * NCS Number of SDRAM banks (chip selects) on this UPM.
- */
projects / u-boot / commitdiff