config TARGET_UCP1020
bool "Support uCP1020"
+config TARGET_CYRUS
+ bool "Support Varisys Cyrus"
+
endchoice
source "board/freescale/b4860qds/Kconfig"
source "board/keymile/kmp204x/Kconfig"
source "board/sbc8548/Kconfig"
source "board/socrates/Kconfig"
+source "board/varisys/cyrus/Kconfig"
source "board/xes/xpedite520x/Kconfig"
source "board/xes/xpedite537x/Kconfig"
source "board/xes/xpedite550x/Kconfig"
--- /dev/null
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+MINIMAL=
+
+ifdef CONFIG_SPL_BUILD
+ifdef CONFIG_SPL_INIT_MINIMAL
+MINIMAL=y
+endif
+endif
+
+ifdef MINIMAL
+# necessary to create built-in.o
+obj- := __dummy__.o
+else
+ifndef CONFIG_SPL_BUILD
+obj-$(CONFIG_ID_EEPROM) += sys_eeprom.o
+endif
+endif
--- /dev/null
+/* EEPROM init functions for Cyrus */
+
+
+void init_eeprom(int bus_num, int addr, int addr_len);
+void mac_read_from_fixed_id(void);
+int mac_read_from_eeprom_common(void);
--- /dev/null
+/*
+ * Based on board/freescale/common/sys_eeprom.c
+ * Copyright 2006, 2008-2009, 2011 Freescale Semiconductor
+ *
+ * This defines the API for storing board information in the
+ * eeprom. It has been adapted from an earlier version of the
+ * Freescale API, but has a number of key differences. Because
+ * the two APIs are independent and may diverge further, the
+ * Varisys version of the API is implemented separately here.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+#include <linux/ctype.h>
+
+#include "eeprom.h"
+
+#ifdef CONFIG_SYS_I2C_EEPROM_NXID_MAC
+#define MAX_NUM_PORTS CONFIG_SYS_I2C_EEPROM_NXID_MAC
+#else
+#define MAX_NUM_PORTS 8
+#endif
+#define NXID_VERSION 0
+
+/**
+ * static eeprom: EEPROM layout for NXID formats
+ *
+ * See Freescale application note AN3638 for details.
+ */
+static struct __attribute__ ((__packed__)) eeprom {
+ u8 id[4]; /* 0x00 - 0x03 EEPROM Tag 'NXID' */
+ u8 sn[12]; /* 0x04 - 0x0F Serial Number */
+ u8 errata[5]; /* 0x10 - 0x14 Errata Level */
+ u8 date[6]; /* 0x15 - 0x1a Build Date */
+ u8 res_0; /* 0x1b Reserved */
+ u32 version; /* 0x1c - 0x1f NXID Version */
+ u8 tempcal[8]; /* 0x20 - 0x27 Temperature Calibration Factors */
+ u8 tempcalsys[2]; /* 0x28 - 0x29 System Temperature Calibration Factors */
+ u8 tempcalflags; /* 0x2a Temperature Calibration Flags */
+ u8 res_1[21]; /* 0x2b - 0x3f Reserved */
+ u8 mac_count; /* 0x40 Number of MAC addresses */
+ u8 mac_flag; /* 0x41 MAC table flags */
+ u8 mac[MAX_NUM_PORTS][6]; /* 0x42 - x MAC addresses */
+ u32 crc; /* x+1 CRC32 checksum */
+} e;
+
+/* Set to 1 if we've read EEPROM into memory */
+static int has_been_read;
+
+/* Is this a valid NXID EEPROM? */
+#define is_valid ((e.id[0] == 'N') || (e.id[1] == 'X') || \
+ (e.id[2] == 'I') || (e.id[3] == 'D'))
+
+/** Fixed ID field in EEPROM */
+static unsigned char uid[16];
+
+static int eeprom_bus_num = -1;
+static int eeprom_addr;
+static int eeprom_addr_len;
+
+/**
+ * This must be called before any eeprom access.
+ */
+void init_eeprom(int bus_num, int addr, int addr_len)
+{
+ eeprom_bus_num = bus_num;
+ eeprom_addr = addr;
+ eeprom_addr_len = addr_len;
+}
+
+/**
+ * show_eeprom - display the contents of the EEPROM
+ */
+void show_eeprom(void)
+{
+ int i;
+ unsigned int crc;
+
+ /* EEPROM tag ID, either CCID or NXID */
+ printf("ID: %c%c%c%c v%u\n", e.id[0], e.id[1], e.id[2], e.id[3],
+ be32_to_cpu(e.version));
+
+ /* Serial number */
+ printf("SN: %s\n", e.sn);
+
+ printf("UID: ");
+ for (i = 0; i < 16; i++)
+ printf("%02x", uid[i]);
+ printf("\n");
+
+ /* Errata level. */
+ printf("Errata: %s\n", e.errata);
+
+ /* Build date, BCD date values, as YYMMDDhhmmss */
+ printf("Build date: 20%02x/%02x/%02x %02x:%02x:%02x %s\n",
+ e.date[0], e.date[1], e.date[2],
+ e.date[3] & 0x7F, e.date[4], e.date[5],
+ e.date[3] & 0x80 ? "PM" : "");
+
+ /* Show MAC addresses */
+ for (i = 0; i < min(e.mac_count, (u8)MAX_NUM_PORTS); i++) {
+ u8 *p = e.mac[i];
+
+ printf("Eth%u: %02x:%02x:%02x:%02x:%02x:%02x\n", i,
+ p[0], p[1], p[2], p[3], p[4], p[5]);
+ }
+
+ crc = crc32(0, (void *)&e, sizeof(e) - 4);
+
+ if (crc == be32_to_cpu(e.crc))
+ printf("CRC: %08x\n", be32_to_cpu(e.crc));
+ else
+ printf("CRC: %08x (should be %08x)\n",
+ be32_to_cpu(e.crc), crc);
+
+#ifdef DEBUG
+ printf("EEPROM dump: (0x%x bytes)\n", sizeof(e));
+ for (i = 0; i < sizeof(e); i++) {
+ if ((i % 16) == 0)
+ printf("%02X: ", i);
+ printf("%02X ", ((u8 *)&e)[i]);
+ if (((i % 16) == 15) || (i == sizeof(e) - 1))
+ printf("\n");
+ }
+#endif
+}
+
+/**
+ * read_eeprom - read the EEPROM into memory
+ */
+int read_eeprom(void)
+{
+ int ret;
+ unsigned int bus;
+
+ if (eeprom_bus_num < 0) {
+ printf("EEPROM not configured\n");
+ return -1;
+ }
+
+ if (has_been_read)
+ return 0;
+
+ bus = i2c_get_bus_num();
+ i2c_set_bus_num(eeprom_bus_num);
+
+ ret = i2c_read(eeprom_addr, 0, eeprom_addr_len,
+ (void *)&e, sizeof(e));
+
+
+ /* Fixed address of ID field */
+ i2c_read(0x5f, 0x80, 1, uid, 16);
+
+ i2c_set_bus_num(bus);
+
+#ifdef DEBUG
+ show_eeprom();
+#endif
+
+ has_been_read = (ret == 0) ? 1 : 0;
+
+ return ret;
+}
+
+/**
+ * update_crc - update the CRC
+ *
+ * This function should be called after each update to the EEPROM structure,
+ * to make sure the CRC is always correct.
+ */
+static void update_crc(void)
+{
+ u32 crc, crc_offset = offsetof(struct eeprom, crc);
+
+ crc = crc32(0, (void *)&e, crc_offset);
+ e.crc = cpu_to_be32(crc);
+}
+
+/**
+ * prog_eeprom - write the EEPROM from memory
+ */
+static int prog_eeprom(void)
+{
+ int ret = 0;
+ int i;
+ void *p;
+ unsigned int bus;
+
+ if (eeprom_bus_num < 0) {
+ printf("EEPROM not configured\n");
+ return -1;
+ }
+
+ /* Set the reserved values to 0xFF */
+ e.res_0 = 0xFF;
+ memset(e.res_1, 0xFF, sizeof(e.res_1));
+ update_crc();
+
+ bus = i2c_get_bus_num();
+ i2c_set_bus_num(eeprom_bus_num);
+
+ /*
+ * The AT24C02 datasheet says that data can only be written in page
+ * mode, which means 8 bytes at a time, and it takes up to 5ms to
+ * complete a given write.
+ */
+ for (i = 0, p = &e; i < sizeof(e); i += 8, p += 8) {
+ ret = i2c_write(eeprom_addr, i, eeprom_addr_len,
+ p, min((int)(sizeof(e) - i), 8));
+ if (ret)
+ break;
+ udelay(5000); /* 5ms write cycle timing */
+ }
+
+ if (!ret) {
+ /* Verify the write by reading back the EEPROM and comparing */
+ struct eeprom e2;
+
+ ret = i2c_read(eeprom_addr, 0,
+ eeprom_addr_len, (void *)&e2, sizeof(e2));
+ if (!ret && memcmp(&e, &e2, sizeof(e)))
+ ret = -1;
+ }
+
+ i2c_set_bus_num(bus);
+
+ if (ret) {
+ printf("Programming failed.\n");
+ has_been_read = 0;
+ return -1;
+ }
+
+ printf("Programming passed.\n");
+ return 0;
+}
+
+/**
+ * h2i - converts hex character into a number
+ *
+ * This function takes a hexadecimal character (e.g. '7' or 'C') and returns
+ * the integer equivalent.
+ */
+static inline u8 h2i(char p)
+{
+ if ((p >= '0') && (p <= '9'))
+ return p - '0';
+
+ if ((p >= 'A') && (p <= 'F'))
+ return (p - 'A') + 10;
+
+ if ((p >= 'a') && (p <= 'f'))
+ return (p - 'a') + 10;
+
+ return 0;
+}
+
+/**
+ * set_date - stores the build date into the EEPROM
+ *
+ * This function takes a pointer to a string in the format "YYMMDDhhmmss"
+ * (2-digit year, 2-digit month, etc), converts it to a 6-byte BCD string,
+ * and stores it in the build date field of the EEPROM local copy.
+ */
+static void set_date(const char *string)
+{
+ unsigned int i;
+
+ if (strlen(string) != 12) {
+ printf("Usage: mac date YYMMDDhhmmss\n");
+ return;
+ }
+
+ for (i = 0; i < 6; i++)
+ e.date[i] = h2i(string[2 * i]) << 4 | h2i(string[2 * i + 1]);
+
+ update_crc();
+}
+
+/**
+ * set_mac_address - stores a MAC address into the EEPROM
+ *
+ * This function takes a pointer to MAC address string
+ * (i.e."XX:XX:XX:XX:XX:XX", where "XX" is a two-digit hex number) and
+ * stores it in one of the MAC address fields of the EEPROM local copy.
+ */
+static void set_mac_address(unsigned int index, const char *string)
+{
+ char *p = (char *)string;
+ unsigned int i;
+
+ if ((index >= MAX_NUM_PORTS) || !string) {
+ printf("Usage: mac <n> XX:XX:XX:XX:XX:XX\n");
+ return;
+ }
+
+ for (i = 0; *p && (i < 6); i++) {
+ e.mac[index][i] = simple_strtoul(p, &p, 16);
+ if (*p == ':')
+ p++;
+ }
+
+ update_crc();
+}
+
+int do_mac(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ char cmd;
+
+ if (argc == 1) {
+ show_eeprom();
+ return 0;
+ }
+
+ cmd = argv[1][0];
+
+ if (cmd == 'r') {
+ read_eeprom();
+ return 0;
+ }
+
+ if (cmd == 'i') {
+ memcpy(e.id, "NXID", sizeof(e.id));
+ e.version = NXID_VERSION;
+ update_crc();
+ return 0;
+ }
+
+ if (!is_valid) {
+ printf("Please read the EEPROM ('r') and/or set the ID ('i') first.\n");
+ return 0;
+ }
+
+ if (argc == 2) {
+ switch (cmd) {
+ case 's': /* save */
+ prog_eeprom();
+ break;
+ default:
+ return cmd_usage(cmdtp);
+ }
+
+ return 0;
+ }
+
+ /* We know we have at least one parameter */
+
+ switch (cmd) {
+ case 'n': /* serial number */
+ memset(e.sn, 0, sizeof(e.sn));
+ strncpy((char *)e.sn, argv[2], sizeof(e.sn) - 1);
+ update_crc();
+ break;
+ case 'e': /* errata */
+ memset(e.errata, 0, 5);
+ strncpy((char *)e.errata, argv[2], 4);
+ update_crc();
+ break;
+ case 'd': /* date BCD format YYMMDDhhmmss */
+ set_date(argv[2]);
+ break;
+ case 'p': /* MAC table size */
+ e.mac_count = simple_strtoul(argv[2], NULL, 16);
+ update_crc();
+ break;
+ case '0' ... '9': /* "mac 0" through "mac 22" */
+ set_mac_address(simple_strtoul(argv[1], NULL, 10), argv[2]);
+ break;
+ case 'h': /* help */
+ default:
+ return cmd_usage(cmdtp);
+ }
+
+ return 0;
+}
+
+int mac_read_from_generic_eeprom(const char *envvar, int chip,
+ int address, int mac_bus)
+{
+ int ret;
+ unsigned int bus;
+ unsigned char mac[6];
+ char ethaddr[18];
+
+ bus = i2c_get_bus_num();
+ i2c_set_bus_num(mac_bus);
+
+ ret = i2c_read(chip, address, 1, mac, 6);
+
+ i2c_set_bus_num(bus);
+
+ if (!ret) {
+ sprintf(ethaddr, "%02X:%02X:%02X:%02X:%02X:%02X",
+ mac[0],
+ mac[1],
+ mac[2],
+ mac[3],
+ mac[4],
+ mac[5]);
+
+ printf("MAC: %s\n", ethaddr);
+ setenv(envvar, ethaddr);
+ }
+
+ return ret;
+}
+
+void mac_read_from_fixed_id(void)
+{
+#ifdef CONFIG_SYS_I2C_MAC1_CHIP_ADDR
+ mac_read_from_generic_eeprom("ethaddr", CONFIG_SYS_I2C_MAC1_CHIP_ADDR,
+ CONFIG_SYS_I2C_MAC1_DATA_ADDR, CONFIG_SYS_I2C_MAC1_BUS);
+#endif
+#ifdef CONFIG_SYS_I2C_MAC2_CHIP_ADDR
+ mac_read_from_generic_eeprom("eth1addr", CONFIG_SYS_I2C_MAC2_CHIP_ADDR,
+ CONFIG_SYS_I2C_MAC2_DATA_ADDR, CONFIG_SYS_I2C_MAC2_BUS);
+#endif
+}
+
+/**
+ * mac_read_from_eeprom - read the MAC addresses from EEPROM
+ *
+ * This function reads the MAC addresses from EEPROM and sets the
+ * appropriate environment variables for each one read.
+ *
+ * The environment variables are only set if they haven't been set already.
+ * This ensures that any user-saved variables are never overwritten.
+ *
+ * This function must be called after relocation.
+ *
+ * For NXID v1 EEPROMs, we support loading and up-converting the older NXID v0
+ * format. In a v0 EEPROM, there are only eight MAC addresses and the CRC is
+ * located at a different offset.
+ */
+int mac_read_from_eeprom_common(void)
+{
+ unsigned int i;
+ u32 crc, crc_offset = offsetof(struct eeprom, crc);
+ u32 *crcp; /* Pointer to the CRC in the data read from the EEPROM */
+
+ puts("EEPROM: ");
+
+ if (read_eeprom()) {
+ printf("Read failed.\n");
+ return 0;
+ }
+
+ if (!is_valid) {
+ printf("Invalid ID (%02x %02x %02x %02x)\n",
+ e.id[0], e.id[1], e.id[2], e.id[3]);
+ return 0;
+ }
+
+ crc = crc32(0, (void *)&e, crc_offset);
+ crcp = (void *)&e + crc_offset;
+ if (crc != be32_to_cpu(*crcp)) {
+ printf("CRC mismatch (%08x != %08x)\n", crc,
+ be32_to_cpu(e.crc));
+ return 0;
+ }
+
+ /*
+ * MAC address #9 in v1 occupies the same position as the CRC in v0.
+ * Erase it so that it's not mistaken for a MAC address. We'll
+ * update the CRC later.
+ */
+ if (e.version == 0)
+ memset(e.mac[8], 0xff, 6);
+
+ for (i = 0; i < min(e.mac_count, (u8)MAX_NUM_PORTS); i++) {
+ if (memcmp(&e.mac[i], "\0\0\0\0\0\0", 6) &&
+ memcmp(&e.mac[i], "\xFF\xFF\xFF\xFF\xFF\xFF", 6)) {
+ char ethaddr[18];
+ char enetvar[9];
+
+ sprintf(ethaddr, "%02X:%02X:%02X:%02X:%02X:%02X",
+ e.mac[i][0],
+ e.mac[i][1],
+ e.mac[i][2],
+ e.mac[i][3],
+ e.mac[i][4],
+ e.mac[i][5]);
+ sprintf(enetvar, i ? "eth%daddr" : "ethaddr", i);
+ /* Only initialize environment variables that are blank
+ * (i.e. have not yet been set)
+ */
+ if (!getenv(enetvar))
+ setenv(enetvar, ethaddr);
+ }
+ }
+
+ printf("%c%c%c%c v%u\n", e.id[0], e.id[1], e.id[2], e.id[3],
+ be32_to_cpu(e.version));
+
+ return 0;
+}
--- /dev/null
+if TARGET_CYRUS
+
+config SYS_BOARD
+ default "cyrus"
+
+config SYS_VENDOR
+ default "varisys"
+
+config SYS_CONFIG_NAME
+ default "cyrus"
+
+endif
--- /dev/null
+Cyrus BOARD
+M: Andy Fleming <afleming@gmail.com>
+S: Maintained
+F: board/varisys/cyrus/
+F: include/configs/cyrus.h
+F: configs/Cyrus_P5020_defconfig
+F: configs/Cyrus_P5040_defconfig
--- /dev/null
+#
+
+obj-y += $(BOARD).o
+obj-y += ddr.o
+obj-y += law.o
+obj-y += tlb.o
+obj-y += eth.o
+obj-$(CONFIG_PCI) += pci.o
--- /dev/null
+Rebuilding u-boot for Cyrus
+
+The Cyrus defconfigs are Cyrus_P5020_defconfig and Cyrus_P5040_defconfig.
+
+They currently disable size optimization in order to avoid a relocation
+bug in some versions of GCC. As the output size is a constant, the size
+optimization is not currently important.
+
+Cyrus boots off a microSD card in a slot on the motherboard. This requires
+that the u-boot is built for the Pre-Boot Loader on the P5020/P5040.
+In order to reflash u-boot, you must download u-boot.pbl, then write it
+onto the card. To do that from u-boot:
+
+> tftp 1000000 u-boot.pbl
+> mmc write 1000000 8 672
+
+If you want to do this via a card reader in linux:
+
+> dd if=u-boot.pbl of=/dev/sdX bs=512 oseek=8
--- /dev/null
+/*
+ * Based on corenet_ds.c
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <linux/compiler.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <fm_eth.h>
+#include <pci.h>
+
+#include "cyrus.h"
+#include "../common/eeprom.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define GPIO_OPENDRAIN 0x30000000
+#define GPIO_DIR 0x3c000004
+#define GPIO_INITIAL 0x30000000
+#define GPIO_VGA_SWITCH 0x00001000
+
+int checkboard(void)
+{
+ printf("Board: CYRUS\n");
+
+ return 0;
+}
+
+int board_early_init_f(void)
+{
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
+
+ /*
+ * Only use DDR1_MCK0/3 and DDR2_MCK0/3
+ * disable DDR1_MCK1/2/4/5 and DDR2_MCK1/2/4/5 to reduce
+ * the noise introduced by these unterminated and unused clock pairs.
+ */
+ setbits_be32(&gur->ddrclkdr, 0x001B001B);
+
+ /* Set GPIO reset lines to open-drain, tristate */
+ setbits_be32(&pgpio->gpdat, GPIO_INITIAL);
+ setbits_be32(&pgpio->gpodr, GPIO_OPENDRAIN);
+
+ /* Set GPIO Direction */
+ setbits_be32(&pgpio->gpdir, GPIO_DIR);
+
+ return 0;
+}
+
+int board_early_init_r(void)
+{
+ fsl_lbc_t *lbc = LBC_BASE_ADDR;
+
+ out_be32(&lbc->lbcr, 0);
+ /* 1 clock LALE cycle */
+ out_be32(&lbc->lcrr, 0x80000000 | CONFIG_SYS_LBC_LCRR);
+
+ set_liodns();
+
+#ifdef CONFIG_SYS_DPAA_QBMAN
+ setup_portals();
+#endif
+ print_lbc_regs();
+ return 0;
+}
+
+int misc_init_r(void)
+{
+ return 0;
+}
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#ifdef CONFIG_PCI
+ pci_of_setup(blob, bd);
+#endif
+
+ fdt_fixup_liodn(blob);
+ fdt_fixup_dr_usb(blob, bd);
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+ fdt_fixup_fman_ethernet(blob);
+#endif
+
+ return 0;
+}
+
+int mac_read_from_eeprom(void)
+{
+ init_eeprom(CONFIG_SYS_EEPROM_BUS_NUM,
+ CONFIG_SYS_I2C_EEPROM_ADDR,
+ CONFIG_SYS_I2C_EEPROM_ADDR_LEN);
+
+ return mac_read_from_eeprom_common();
+}
--- /dev/null
+/*
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CYRUS_H
+#define __CYRUS_H
+
+void fdt_fixup_board_enet(void *blob);
+void pci_of_setup(void *blob, bd_t *bd);
+
+#endif
--- /dev/null
+/*
+ * Based on corenet_ds ddr code
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <hwconfig.h>
+#include <asm/mmu.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include <asm/fsl_law.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+
+struct board_specific_parameters {
+ u32 n_ranks;
+ u32 datarate_mhz_high;
+ u32 clk_adjust;
+ u32 wrlvl_start;
+ u32 cpo;
+ u32 write_data_delay;
+ u32 force_2t;
+};
+
+/*
+ * This table contains all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ */
+static const struct board_specific_parameters udimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| clk| wrlvl | cpo |wrdata|2T
+ * ranks| mhz|adjst| start | |delay |
+ */
+ {4, 850, 4, 6, 0xff, 2, 0},
+ {4, 950, 5, 7, 0xff, 2, 0},
+ {4, 1050, 5, 8, 0xff, 2, 0},
+ {4, 1250, 5, 10, 0xff, 2, 0},
+ {4, 1350, 5, 11, 0xff, 2, 0},
+ {4, 1666, 5, 12, 0xff, 2, 0},
+ {2, 850, 5, 6, 0xff, 2, 0},
+ {2, 1050, 5, 7, 0xff, 2, 0},
+ {2, 1250, 4, 6, 0xff, 2, 0},
+ {2, 1350, 5, 7, 0xff, 2, 0},
+ {2, 1666, 5, 8, 0xff, 2, 0},
+ {1, 1250, 4, 6, 0xff, 2, 0},
+ {1, 1335, 4, 7, 0xff, 2, 0},
+ {1, 1666, 4, 8, 0xff, 2, 0},
+ {}
+};
+
+/*
+ * The two slots have slightly different timing. The center values are good
+ * for both slots. We use identical speed tables for them. In future use, if
+ * DIMMs have fewer center values that require two separated tables, copy the
+ * udimm0 table to udimm1 and make changes to clk_adjust and wrlvl_start.
+ */
+static const struct board_specific_parameters *udimms[] = {
+ udimm0,
+ udimm0,
+};
+
+static const struct board_specific_parameters rdimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| clk| wrlvl | cpo |wrdata|2T
+ * ranks| mhz|adjst| start | |delay |
+ */
+ {4, 850, 4, 6, 0xff, 2, 0},
+ {4, 950, 5, 7, 0xff, 2, 0},
+ {4, 1050, 5, 8, 0xff, 2, 0},
+ {4, 1250, 5, 10, 0xff, 2, 0},
+ {4, 1350, 5, 11, 0xff, 2, 0},
+ {4, 1666, 5, 12, 0xff, 2, 0},
+ {2, 850, 4, 6, 0xff, 2, 0},
+ {2, 1050, 4, 7, 0xff, 2, 0},
+ {2, 1666, 4, 8, 0xff, 2, 0},
+ {1, 850, 4, 5, 0xff, 2, 0},
+ {1, 950, 4, 7, 0xff, 2, 0},
+ {1, 1666, 4, 8, 0xff, 2, 0},
+ {}
+};
+
+/*
+ * The two slots have slightly different timing. See comments above.
+ */
+static const struct board_specific_parameters *rdimms[] = {
+ rdimm0,
+ rdimm0,
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+ ulong ddr_freq;
+
+ if (ctrl_num > 1) {
+ printf("Wrong parameter for controller number %d", ctrl_num);
+ return;
+ }
+ if (!pdimm->n_ranks)
+ return;
+
+ if (popts->registered_dimm_en)
+ pbsp = rdimms[ctrl_num];
+ else
+ pbsp = udimms[ctrl_num];
+
+
+ /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+ * freqency and n_banks specified in board_specific_parameters table.
+ */
+ ddr_freq = get_ddr_freq(0) / 1000000;
+ while (pbsp->datarate_mhz_high) {
+ if (pbsp->n_ranks == pdimm->n_ranks) {
+ if (ddr_freq <= pbsp->datarate_mhz_high) {
+ popts->cpo_override = pbsp->cpo;
+ popts->write_data_delay =
+ pbsp->write_data_delay;
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->wrlvl_start = pbsp->wrlvl_start;
+ popts->twot_en = pbsp->force_2t;
+ goto found;
+ }
+ pbsp_highest = pbsp;
+ }
+ pbsp++;
+ }
+
+ if (pbsp_highest) {
+ printf("Error: board specific timing not found for data rate %lu MT/s!\nTrying to use the highest speed (%u) parameters\n",
+ ddr_freq, pbsp_highest->datarate_mhz_high);
+ popts->cpo_override = pbsp_highest->cpo;
+ popts->write_data_delay = pbsp_highest->write_data_delay;
+ popts->clk_adjust = pbsp_highest->clk_adjust;
+ popts->wrlvl_start = pbsp_highest->wrlvl_start;
+ popts->twot_en = pbsp_highest->force_2t;
+ } else {
+ panic("DIMM is not supported by this board");
+ }
+found:
+ /*
+ * Factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+ popts->half_strength_driver_enable = 0;
+ /*
+ * Write leveling override
+ */
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+
+ /*
+ * Rtt and Rtt_WR override
+ */
+ popts->rtt_override = 0;
+
+ /* Enable ZQ calibration */
+ popts->zq_en = 1;
+
+ /* DHC_EN =1, ODT = 60 Ohm */
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN;
+}
+
+phys_size_t initdram(int board_type)
+{
+ phys_size_t dram_size;
+
+ puts("Initializing....");
+
+ if (!fsl_use_spd())
+ panic("Cyrus only supports using SPD for DRAM\n");
+
+ puts("using SPD\n");
+ dram_size = fsl_ddr_sdram();
+
+ dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+ dram_size *= 0x100000;
+
+ debug(" DDR: ");
+ return dram_size;
+}
--- /dev/null
+/*
+ * Author Adrian Cox
+ * Based somewhat on board/freescale/corenet_ds/eth_hydra.c
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <netdev.h>
+#include <asm/fsl_serdes.h>
+#include <fm_eth.h>
+#include <fsl_mdio.h>
+#include <malloc.h>
+#include <fdt_support.h>
+#include <fsl_dtsec.h>
+
+#ifdef CONFIG_FMAN_ENET
+
+#define FIRST_PORT_ADDR 3
+#define SECOND_PORT_ADDR 7
+
+#ifdef CONFIG_PPC_P5040
+#define FIRST_PORT FM1_DTSEC5
+#define SECOND_PORT FM2_DTSEC5
+#else
+#define FIRST_PORT FM1_DTSEC4
+#define SECOND_PORT FM1_DTSEC5
+#endif
+
+#define IS_VALID_PORT(p) ((p) == FIRST_PORT || (p) == SECOND_PORT)
+
+static void cyrus_phy_tuning(int phy)
+{
+ /*
+ * Enable RGMII delay on Tx and Rx for CPU port
+ */
+ printf("Tuning PHY @ %d\n", phy);
+
+ /* sets address 0x104 or reg 260 for writing */
+ miiphy_write(DEFAULT_FM_MDIO_NAME, phy, 0xb, 0x8104);
+ /* Sets RXC/TXC to +0.96ns and TX_CTL/RX_CTL to -0.84ns */
+ miiphy_write(DEFAULT_FM_MDIO_NAME, phy, 0xc, 0xf0f0);
+ /* sets address 0x105 or reg 261 for writing */
+ miiphy_write(DEFAULT_FM_MDIO_NAME, phy, 0xb, 0x8105);
+ /* writes to address 0x105 , RXD[3..0] to -0. */
+ miiphy_write(DEFAULT_FM_MDIO_NAME, phy, 0xc, 0x0000);
+ /* sets address 0x106 or reg 261 for writing */
+ miiphy_write(DEFAULT_FM_MDIO_NAME, phy, 0xb, 0x8106);
+ /* writes to address 0x106 , TXD[3..0] to -0.84ns */
+ miiphy_write(DEFAULT_FM_MDIO_NAME, phy, 0xc, 0x0000);
+ /* force re-negotiation */
+ miiphy_write(DEFAULT_FM_MDIO_NAME, phy, 0x0, 0x1340);
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+#ifdef CONFIG_FMAN_ENET
+ struct fsl_pq_mdio_info dtsec_mdio_info;
+ unsigned int i;
+
+ printf("Initializing Fman\n");
+
+
+ /* Register the real 1G MDIO bus */
+ dtsec_mdio_info.regs =
+ (struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR;
+ dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
+
+ fsl_pq_mdio_init(bis, &dtsec_mdio_info);
+
+
+ fm_info_set_phy_address(FIRST_PORT, FIRST_PORT_ADDR);
+ fm_info_set_mdio(FIRST_PORT,
+ miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME));
+ fm_info_set_phy_address(SECOND_PORT, SECOND_PORT_ADDR);
+ fm_info_set_mdio(SECOND_PORT,
+ miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME));
+
+ /* Never disable DTSEC1 - it controls MDIO */
+ for (i = FM1_DTSEC2; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
+ if (!IS_VALID_PORT(i))
+ fm_disable_port(i);
+ }
+
+#ifdef CONFIG_PPC_P5040
+ for (i = FM2_DTSEC2; i < FM2_DTSEC1 + CONFIG_SYS_NUM_FM2_DTSEC; i++) {
+ if (!IS_VALID_PORT(i))
+ fm_disable_port(i);
+ }
+#endif
+
+ cpu_eth_init(bis);
+
+ cyrus_phy_tuning(FIRST_PORT_ADDR);
+ cyrus_phy_tuning(SECOND_PORT_ADDR);
+#endif
+
+ return pci_eth_init(bis);
+}
--- /dev/null
+/*
+ * Author: Adrian Cox
+ * Based on corenet_ds law files.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+ SET_LAW(CONFIG_SYS_LBC0_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_LBC),
+ SET_LAW(CONFIG_SYS_LBC1_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_LBC),
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+ SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_BMAN),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+ SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_QMAN),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ /* Limit DCSR to 32M to access NPC Trace Buffer */
+ SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
--- /dev/null
+#
+# Copyright 2012 Freescale Semiconductor, Inc.
+#
+# Refer docs/README.pblimage for more details about how-to configure
+# and create PBL boot image
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+#PBI commands
+#Initialize CPC1 as 1MB SRAM
+09010000 00200400
+09138000 00000000
+091380c0 00000100
+09010100 00000000
+09010104 fff0000b
+09010f00 08000000
+09010000 80000000
+#Configure LAW for CPC1
+09000d00 00000000
+09000d04 fff00000
+09000d08 81000013
+09000010 00000000
+09000014 ff000000
+09000018 81000000
+#Initialize eSPI controller, default configuration is slow for eSPI to
+#load data, this configuration comes from u-boot eSPI driver.
+09110000 80000403
+09110020 2d170008
+09110024 00100008
+09110028 00100008
+0911002c 00100008
+#Flush PBL data
+09138000 00000000
+091380c0 00000000
--- /dev/null
+/*
+ * Copyright 2007-2011 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/fsl_pci.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <asm/fsl_serdes.h>
+
+void pci_init_board(void)
+{
+ fsl_pcie_init_board(0);
+}
+
+void pci_of_setup(void *blob, bd_t *bd)
+{
+ FT_FSL_PCI_SETUP;
+}
--- /dev/null
+#
+# Default RCW for Cyrus P5020
+#
+
+#PBL preamble and RCW header
+aa55aa55 010e0100
+#64 bytes RCW data
+0c540000 00000000 1e1e0000 00000000
+44808c00 ff002000 68000000 45000000
+00000000 00000000 00000000 0003000f
+a0000000 00000000 00000000 00000000
--- /dev/null
+#
+# Default RCW for Cyrus P5040
+#
+
+#PBL preamble and RCW header
+aa55aa55 010e0100
+#64 bytes RCW data
+90e00000 00000000 acac9800 00440000
+44808c00 ff29a000 68000000 61000000
+00000000 00000000 00000000 0003000f
+a0000000 00000000 00000000 00000000
--- /dev/null
+/*
+ * Author: Adrian Cox
+ * Based on corenet_ds tlb code
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+ /* TLB 0 - for temp stack in cache */
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+ MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+ MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+ MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+ MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ /* TLB 1 */
+ /* *I*** - Covers boot page */
+#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
+ /*
+ * *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the
+ * SRAM is at 0xfff00000, it covered the 0xfffff000.
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_1M, 1),
+#else
+ SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_4K, 1),
+#endif
+
+ /* *I*G* - CCSRBAR */
+ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 1, BOOKE_PAGESZ_16M, 1),
+
+ /* Local Bus */
+ SET_TLB_ENTRY(1, CONFIG_SYS_LBC0_BASE, CONFIG_SYS_LBC0_BASE_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 2, BOOKE_PAGESZ_64K, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_LBC1_BASE, CONFIG_SYS_LBC1_BASE_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 3, BOOKE_PAGESZ_4K, 1),
+
+ /* *I*G* - PCI */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 4, BOOKE_PAGESZ_1G, 1),
+
+ /* *I*G* - PCI */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x40000000,
+ CONFIG_SYS_PCIE1_MEM_PHYS + 0x40000000,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 5, BOOKE_PAGESZ_256M, 1),
+
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x50000000,
+ CONFIG_SYS_PCIE1_MEM_PHYS + 0x50000000,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 6, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - PCI I/O */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 7, BOOKE_PAGESZ_256K, 1),
+
+ /* Bman/Qman */
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
+ MAS3_SW|MAS3_SR, 0,
+ 0, 9, BOOKE_PAGESZ_1M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x00100000,
+ CONFIG_SYS_BMAN_MEM_PHYS + 0x00100000,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 10, BOOKE_PAGESZ_1M, 1),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
+ MAS3_SW|MAS3_SR, 0,
+ 0, 11, BOOKE_PAGESZ_1M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x00100000,
+ CONFIG_SYS_QMAN_MEM_PHYS + 0x00100000,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 12, BOOKE_PAGESZ_1M, 1),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
+ MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 13, BOOKE_PAGESZ_4M, 1),
+#endif
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
--- /dev/null
+CONFIG_PPC=y
+CONFIG_MPC85xx=y
+CONFIG_TARGET_CYRUS=y
+CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SYS_TEXT_BASE=0xFFF40000,PPC_P5020"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_NETDEVICES=y
+CONFIG_E1000=y
--- /dev/null
+CONFIG_PPC=y
+CONFIG_MPC85xx=y
+CONFIG_TARGET_CYRUS=y
+CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SYS_TEXT_BASE=0xFFF40000,PPC_P5040"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_NETDEVICES=y
+CONFIG_E1000=y
--- /dev/null
+/*
+ * Based on corenet_ds.h
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define CONFIG_CYRUS
+
+#define CONFIG_PHYS_64BIT
+
+#if !defined(CONFIG_PPC_P5020) && !defined(CONFIG_PPC_P5040)
+#error Must call Cyrus CONFIG with a specific CPU enabled.
+#endif
+
+
+#define CONFIG_MMC
+#define CONFIG_SDCARD
+#define CONFIG_FSL_SATA_V2
+#define CONFIG_PCIE3
+#define CONFIG_PCIE4
+#ifdef CONFIG_PPC_P5020
+#define CONFIG_SYS_FSL_RAID_ENGINE
+#define CONFIG_SYS_DPAA_RMAN
+#endif
+#define CONFIG_SYS_DPAA_PME
+
+/*
+ * Corenet DS style board configuration file
+ */
+#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#define CONFIG_SYS_FSL_PBL_PBI board/varisys/cyrus/pbi.cfg
+#if defined(CONFIG_PPC_P5020)
+#define CONFIG_SYS_CLK_FREQ 133000000
+#define CONFIG_SYS_FSL_PBL_RCW board/varisys/cyrus/rcw_p5020_v2.cfg
+#elif defined(CONFIG_PPC_P5040)
+#define CONFIG_SYS_CLK_FREQ 100000000
+#define CONFIG_SYS_FSL_PBL_RCW board/varisys/cyrus/rcw_p5040.cfg
+#endif
+
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE
+#define CONFIG_E500 /* BOOKE e500 family */
+#define CONFIG_E500MC /* BOOKE e500mc family */
+#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
+#define CONFIG_MP /* support multiple processors */
+
+
+#define CONFIG_SYS_MMC_MAX_DEVICE 1
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xeff40000
+#endif
+
+#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
+#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS
+#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */
+#define CONFIG_PCI /* Enable PCI/PCIE */
+#define CONFIG_PCIE1 /* PCIE controler 1 */
+#define CONFIG_PCIE2 /* PCIE controler 2 */
+#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
+
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_SYS_NO_FLASH
+
+#if defined(CONFIG_SDCARD)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_FSL_FIXED_MMC_LOCATION
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_OFFSET (512 * 1658)
+#endif
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_SYS_CACHE_STASHING
+#define CONFIG_BACKSIDE_L2_CACHE
+#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_DDR_ECC
+#ifdef CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
+#endif
+
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_ADDR_MAP
+#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
+#endif
+
+/* test POST memory test */
+#undef CONFIG_POST
+#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00400000
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_PANIC_HANG /* do not reset board on panic */
+
+/*
+ * Config the L3 Cache as L3 SRAM
+ */
+#define CONFIG_SYS_INIT_L3_ADDR CONFIG_RAMBOOT_TEXT_BASE
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_INIT_L3_ADDR_PHYS (0xf00000000ull | CONFIG_RAMBOOT_TEXT_BASE)
+#else
+#define CONFIG_SYS_INIT_L3_ADDR_PHYS CONFIG_SYS_INIT_L3_ADDR
+#endif
+#define CONFIG_SYS_L3_SIZE (1024 << 10)
+#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_DCSRBAR 0xf0000000
+#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
+#endif
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
+
+#define CONFIG_DDR_SPD
+#define CONFIG_SYS_FSL_DDR3
+
+#define CONFIG_SYS_SPD_BUS_NUM 1
+#define SPD_EEPROM_ADDRESS1 0x51
+#define SPD_EEPROM_ADDRESS2 0x52
+#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
+
+/*
+ * Local Bus Definitions
+ */
+
+#define CONFIG_SYS_LBC0_BASE 0xe0000000 /* Start of LBC Registers */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_LBC0_BASE_PHYS 0xfe0000000ull
+#else
+#define CONFIG_SYS_LBC0_BASE_PHYS CONFIG_SYS_LBC0_BASE
+#endif
+
+#define CONFIG_SYS_LBC1_BASE 0xe1000000 /* Start of LBC Registers */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_LBC1_BASE_PHYS 0xfe1000000ull
+#else
+#define CONFIG_SYS_LBC1_BASE_PHYS CONFIG_SYS_LBC1_BASE
+#endif
+
+/* Set the local bus clock 1/16 of platform clock */
+#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_16 | LCRR_EADC_1)
+
+#define CONFIG_SYS_BR0_PRELIM \
+(BR_PHYS_ADDR(CONFIG_SYS_LBC0_BASE_PHYS) | BR_PS_16 | BR_V)
+#define CONFIG_SYS_BR1_PRELIM \
+(BR_PHYS_ADDR(CONFIG_SYS_LBC1_BASE_PHYS) | BR_PS_16 | BR_V)
+
+#define CONFIG_SYS_OR0_PRELIM 0xfff00010
+#define CONFIG_SYS_OR1_PRELIM 0xfff00010
+
+
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
+
+#if defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_HWCONFIG
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+ ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#else
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
+#endif
+#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 /* Size of used area in RAM */
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
+
+/* Serial Port - controlled on board with jumper J8
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
+#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
+#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
+#define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
+#define CONFIG_SYS_FSL_I2C3_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_FSL_I2C3_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
+#define CONFIG_SYS_FSL_I2C4_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_FSL_I2C4_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
+
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
+
+#define CONFIG_SYS_I2C_GENERIC_MAC
+#define CONFIG_SYS_I2C_MAC1_BUS 3
+#define CONFIG_SYS_I2C_MAC1_CHIP_ADDR 0x57
+#define CONFIG_SYS_I2C_MAC1_DATA_ADDR 0xf2
+#define CONFIG_SYS_I2C_MAC2_BUS 0
+#define CONFIG_SYS_I2C_MAC2_CHIP_ADDR 0x50
+#define CONFIG_SYS_I2C_MAC2_DATA_ADDR 0xfa
+
+#define CONFIG_CMD_DATE 1
+#define CONFIG_RTC_MCP79411 1
+#define CONFIG_SYS_RTC_BUS_NUM 3
+#define CONFIG_SYS_I2C_RTC_ADDR 0x6f
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_FSL_ESPI
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+/* controller 1, direct to uli, tgtid 3, Base address 20000 */
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
+#else
+#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000
+#endif
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
+#else
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000
+#endif
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 2, Slot 2, tgtid 2, Base address 201000 */
+#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
+#else
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
+#endif
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
+#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
+#else
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000
+#endif
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 3, Slot 1, tgtid 1, Base address 202000 */
+#define CONFIG_SYS_PCIE3_MEM_VIRT 0xc0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc40000000ull
+#else
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xc0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc0000000
+#endif
+#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
+#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
+#else
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000
+#endif
+#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
+
+/* controller 4, Base address 203000 */
+#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc60000000ull
+#define CONFIG_SYS_PCIE4_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull
+#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */
+
+/* Qman/Bman */
+#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS 10
+#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
+#else
+#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
+#endif
+#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
+#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
+#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
+#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
+#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
+#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
+ CONFIG_SYS_BMAN_CENA_SIZE)
+#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
+#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
+#define CONFIG_SYS_QMAN_NUM_PORTALS 10
+#define CONFIG_SYS_QMAN_MEM_BASE 0xf4200000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_QMAN_MEM_PHYS 0xff4200000ull
+#else
+#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
+#endif
+#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
+#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
+#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
+#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
+#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
+#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
+ CONFIG_SYS_QMAN_CENA_SIZE)
+#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
+#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08
+
+#define CONFIG_SYS_DPAA_FMAN
+/* Default address of microcode for the Linux Fman driver */
+/*
+ * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
+ * about 825KB (1650 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
+#define CONFIG_SYS_FMAN_FW_ADDR (512 * 1680)
+
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
+#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHY_MICREL
+#define CONFIG_PHY_MICREL_KSZ9021
+#endif
+
+#ifdef CONFIG_PCI
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_NET_MULTI
+
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif /* CONFIG_PCI */
+
+/* SATA */
+#ifdef CONFIG_FSL_SATA_V2
+#define CONFIG_LIBATA
+#define CONFIG_FSL_SATA
+
+#define CONFIG_SYS_SATA_MAX_DEVICE 2
+#define CONFIG_SATA1
+#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
+#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
+#define CONFIG_SATA2
+#define CONFIG_SYS_SATA2 CONFIG_SYS_MPC85xx_SATA2_ADDR
+#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA
+
+#define CONFIG_LBA48
+#define CONFIG_CMD_SATA
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+#endif
+
+#ifdef CONFIG_FMAN_ENET
+#define CONFIG_SYS_TBIPA_VALUE 8
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_ETHPRIME "FM1@DTSEC4"
+#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
+#endif
+
+/*
+ * Environment
+ */
+#define CONFIG_LOADS_ECHO /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ERRATA
+#define CONFIG_CMD_GREPENV
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#endif
+
+/*
+ * USB
+ */
+#define CONFIG_HAS_FSL_DR_USB
+#define CONFIG_HAS_FSL_MPH_USB
+
+#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_CMD_EXT2
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_KEYBOARD
+#define CONFIG_SYS_USB_EVENT_POLL
+ /* _VIA_CONTROL_EP */
+#define CONFIG_CONSOLE_MUX
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#endif
+
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ROOTPATH "/opt/nfsroot"
+#define CONFIG_BOOTFILE "uImage"
+#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR 1000000
+
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+
+#define CONFIG_BAUDRATE 115200
+
+#define __USB_PHY_TYPE utmi
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+"hwconfig=fsl_ddr:ctlr_intlv=cacheline," \
+"bank_intlv=cs0_cs1;" \
+"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\
+"usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
+"netdev=eth0\0" \
+"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
+"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
+"consoledev=ttyS0\0" \
+"ramdiskaddr=2000000\0" \
+"fdtaddr=c00000\0" \
+"bdev=sda3\0"
+
+#define CONFIG_HDBOOT \
+"setenv bootargs root=/dev/$bdev rw " \
+"console=$consoledev,$baudrate $othbootargs;" \
+"tftp $loadaddr $bootfile;" \
+"tftp $fdtaddr $fdtfile;" \
+"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_NFSBOOTCOMMAND \
+"setenv bootargs root=/dev/nfs rw " \
+"nfsroot=$serverip:$rootpath " \
+"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+"console=$consoledev,$baudrate $othbootargs;" \
+"tftp $loadaddr $bootfile;" \
+"tftp $fdtaddr $fdtfile;" \
+"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+"setenv bootargs root=/dev/ram rw " \
+"console=$consoledev,$baudrate $othbootargs;" \
+"tftp $ramdiskaddr $ramdiskfile;" \
+"tftp $loadaddr $bootfile;" \
+"tftp $fdtaddr $fdtfile;" \
+"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_HDBOOT
+
+#include <asm/fsl_secure_boot.h>
+
+#ifdef CONFIG_SECURE_BOOT
+#endif
+
+#endif /* __CONFIG_H */
projects / u-boot / commitdiff