#ifdef CONFIG_MXC_OCOTP
void enable_ocotp_clk(unsigned char enable);
#endif
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
void enable_usboh3_clk(unsigned char enable);
#endif
void init_clk_usdhc(u32 index);
}
#endif
-#if defined(CONFIG_USB_OHCI_NEW) || defined(CONFIG_USB_EHCI)
+#if defined(CONFIG_USB_OHCI_NEW) || defined(CONFIG_USB_EHCI_HCD)
void at91_uhp_hw_init(void)
{
/* Enable VBus on UHP ports */
/* TODO: use "mmc-pwrseq-emmc" */
writel(1, SDCTRL_EMMC_HW_RESET);
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
{
/* FIXME: the current clk driver can not handle parents */
u32 tmp;
#ifdef CONFIG_UNIPHIER_ETH
tmp |= SC_CLKCTRL_CEN_ETHER;
#endif
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
tmp |= SC_CLKCTRL_CEN_MIO | SC_CLKCTRL_CEN_STDMAC;
#endif
#ifdef CONFIG_NAND_DENALI
#ifdef CONFIG_UNIPHIER_ETH
tmp |= SC_CLKCTRL_CEN_ETHER;
#endif
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
tmp |= SC_CLKCTRL_CEN_MIO | SC_CLKCTRL_CEN_STDMAC;
#endif
#ifdef CONFIG_NAND_DENALI
at91sam9x5ek_nand_hw_init();
#endif
-#if defined(CONFIG_USB_OHCI_NEW) || defined(CONFIG_USB_EHCI)
+#if defined(CONFIG_USB_OHCI_NEW) || defined(CONFIG_USB_EHCI_HCD)
at91_uhp_hw_init();
#endif
#ifdef CONFIG_LCD
}
#endif
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
static struct omap_usbhs_board_data usbhs_bdata = {
.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
.port_mode[1] = OMAP_EHCI_PORT_MODE_HSIC,
static void setup_net_chip(void);
#endif
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#include <usb.h>
#include <asm/arch/ehci.h>
#include <asm/ehci-omap.h>
return rc;
}
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
static struct omap_usbhs_board_data usbhs_bdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
#include <asm/arch/clock.h>
#include <errno.h>
#include <i2c.h>
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#include <usb.h>
#include <asm/ehci-omap.h>
#endif
/* Address of the framebuffer in RAM. */
#define FB_START_ADDRESS 0x88000000
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
static struct omap_usbhs_board_data usbhs_bdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
.port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
#include <asm/mach-types.h>
#include "overo.h"
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#include <usb.h>
#include <asm/ehci-omap.h>
#endif
}
#endif
-#if defined(CONFIG_USB_EHCI)
+#if defined(CONFIG_USB_EHCI_HCD)
static struct omap_usbhs_board_data usbhs_bdata = {
.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
return omap_ehci_hcd_stop();
}
-#endif /* CONFIG_USB_EHCI */
+#endif /* CONFIG_USB_EHCI_HCD */
}
#endif
-#if defined(CONFIG_USB_EHCI) && !defined(CONFIG_SPL_BUILD)
+#if defined(CONFIG_USB_EHCI_HCD) && !defined(CONFIG_SPL_BUILD)
/* Call usb_stop() before starting the kernel */
void show_boot_progress(int val)
{
{
return omap_ehci_hcd_stop();
}
-#endif /* CONFIG_USB_EHCI */
+#endif /* CONFIG_USB_EHCI_HCD */
#include <spl.h>
#include <mmc.h>
#include <asm/gpio.h>
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#include <usb.h>
#include <asm/ehci-omap.h>
#endif
XR16L2751_GPMC_CONFIG6,
};
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
static struct omap_usbhs_board_data usbhs_bdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
#include <i2c.h>
#include <spartan3.h>
#include <asm/gpio.h>
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#include <usb.h>
#include <asm/ehci-omap.h>
#endif
FPGA_GPMC_CONFIG6,
};
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
static struct omap_usbhs_board_data usbhs_bdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
#include "beagle.h"
#include <command.h>
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#include <usb.h>
#include <asm/ehci-omap.h>
#endif
}
#endif
-#if defined(CONFIG_USB_EHCI) && !defined(CONFIG_SPL_BUILD)
+#if defined(CONFIG_USB_EHCI_HCD) && !defined(CONFIG_SPL_BUILD)
/* Call usb_stop() before starting the kernel */
void show_boot_progress(int val)
{
return omap_ehci_hcd_stop();
}
-#endif /* CONFIG_USB_EHCI */
+#endif /* CONFIG_USB_EHCI_HCD */
#if defined(CONFIG_USB_ETHER) && defined(CONFIG_USB_MUSB_GADGET)
int board_eth_init(bd_t *bis)
#include "mux_data.h"
-#if defined(CONFIG_USB_EHCI) || defined(CONFIG_USB_XHCI_OMAP)
+#if defined(CONFIG_USB_EHCI_HCD) || defined(CONFIG_USB_XHCI_OMAP)
#include <sata.h>
#include <usb.h>
#include <asm/gpio.h>
return 0;
}
-#if defined(CONFIG_USB_EHCI) || defined(CONFIG_USB_XHCI_OMAP)
+#if defined(CONFIG_USB_EHCI_HCD) || defined(CONFIG_USB_XHCI_OMAP)
static void enable_host_clocks(void)
{
int auxclk;
}
#endif
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
static struct omap_usbhs_board_data usbhs_bdata = {
.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
.port_mode[1] = OMAP_EHCI_PORT_MODE_HSIC,
#include "panda_mux_data.h"
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#include <usb.h>
#include <asm/arch/ehci.h>
#include <asm/ehci-omap.h>
#endif
#endif
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
static struct omap_usbhs_board_data usbhs_bdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
trans_cmnd transport; /* transport routine */
};
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
/*
* The U-Boot EHCI driver can handle any transfer length as long as there is
* enough free heap space left, but the SCSI READ(10) and WRITE(10) commands are
You may want to read <file:Documentation/usb/ehci.txt>.
-config USB_EHCI
- bool
- default USB_EHCI_HCD
- ---help---
- TODO: rename after most boards switch to Kconfig
-
if USB_EHCI_HCD
config USB_EHCI_ATMEL
obj-$(CONFIG_USB_OHCI_GENERIC) += ohci-generic.o
# echi
-obj-$(CONFIG_USB_EHCI) += ehci-hcd.o
+obj-$(CONFIG_USB_EHCI_HCD) += ehci-hcd.o
obj-$(CONFIG_USB_EHCI_ARMADA100) += ehci-armada100.o utmi-armada100.o
obj-$(CONFIG_USB_EHCI_ATMEL) += ehci-atmel.o
ifdef CONFIG_MPC512X
#define CONFIG_HAS_FSL_DR_USB
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
#define CONFIG_SHA_HW_ACCEL
#endif
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#define CONFIG_HAS_FSL_DR_USB
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
#endif
-#define CONFIG_USB_EHCI /* USB */
-#ifdef CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD /* USB */
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#define CONFIG_HAS_FSL_DR_USB
/* USB */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_SYS_USB_EHCI_REGS_BASE 0xFC0B0000
#define CONFIG_SYS_USB_EHCI_CPU_INIT
#endif
#define CONFIG_HAS_FSL_DR_USB
#define CONFIG_SYS_SCCR_USBDRCM 3
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_USB_PHY_TYPE "utmi"
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
/*
* Support USB
*/
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
/* Current USB implementation supports the only USB controller,
#define CONFIG_PQ_MDS_PIB 1 /* PQ MDS Platform IO Board */
#define CONFIG_HAS_FSL_DR_USB 1 /* fixup device tree for the DR USB */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_ENV_OVERWRITE
#define CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
*/
#define CONFIG_HAS_FSL_MPH_USB
#ifdef CONFIG_HAS_FSL_MPH_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#endif
/*
* USB
*/
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_PCI
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_PCI_EHCI_DEVICE 0
/*
* USB
*/
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_PCI
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_PCI_EHCI_DEVICE 0
#define CONFIG_HAS_FSL_DR_USB
#if defined(CONFIG_HAS_FSL_DR_USB)
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#endif
#undef CONFIG_WATCHDOG /* watchdog disabled */
-#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI) \
+#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI_HCD) \
|| defined(CONFIG_FSL_SATA)
#endif
*/
#define CONFIG_HAS_FSL_DR_USB
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#endif
*/
#define CONFIG_HAS_FSL_DR_USB
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#endif
#define CONFIG_HAS_FSL_MPH_USB
#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
#define CONFIG_HAS_FSL_DR_USB
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
#define CONFIG_HAS_FSL_DR_USB
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
#define CONFIG_HAS_FSL_DR_USB
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
#define CONFIG_HAS_FSL_DR_USB
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
#define __T208xQDS_H
#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#if defined(CONFIG_ARCH_T2080)
#define CONFIG_FSL_SATA_V2
#define CONFIG_SYS_SRIO /* Enable Serial RapidIO Support */
/*
* USB
*/
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_HAS_FSL_DR_USB
#define __T2080RDB_H
#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_FSL_SATA_V2
/* High Level Configuration Options */
/*
* USB
*/
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_HAS_FSL_DR_USB
/*
* USB
*/
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_HAS_FSL_DR_USB
/*
* USB
*/
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_HAS_FSL_DR_USB
#define CONFIG_HAS_FSL_DR_USB
#if defined(CONFIG_HAS_FSL_DR_USB)
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#endif
#define CONFIG_BOUNCE_BUFFER
/* USB Configs */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_STORAGE
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_SYS_I2C_POWERIC_ADDR 0x58 /* da9063 */
/* USB */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_RMOBILE
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_SYS_MMC_ENV_PART 1
/* USB host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* PCI host support */
#define CONFIG_SYS_MMC_ENV_PART 1
/* USB host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* PCI host support */
#define CONFIG_RTC_M41T11
/* USB Configs */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
#define CONFIG_CMD_NAND
/*
- * define CONFIG_USB_EHCI to enable USB Hi-Speed (aka 2.0)
+ * define CONFIG_USB_EHCI_HCD to enable USB Hi-Speed (aka 2.0)
* NB: in this case, USB 1.1 devices won't be recognized.
*/
/* USB */
#ifdef CONFIG_CMD_USB
-#ifndef CONFIG_USB_EHCI
+#ifndef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_ATMEL
#define CONFIG_USB_ATMEL_CLK_SEL_UPLL
#define CONFIG_USB_OHCI_NEW
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB Host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB Host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB Host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
/* USB Configs */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_HOST_ETHER
/* USB */
#define CONFIG_USB_OMAP3
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_OMAP
#define CONFIG_USB_MUSB_UDC
#define CONFIG_TWL4030_USB
#ifndef CONFIG_USB_MUSB_AM35X
#define CONFIG_USB_OMAP3
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_OMAP
#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 146
#define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO 147
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
CONFIG_SYS_SCSI_MAX_LUN)
/* USB UHH support options */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_OMAP
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_SYS_I2C_TEGRA
/* USB host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
#define CONFIG_USB_MAX_CONTROLLER_COUNT 3
#define CONFIG_SYS_MMC_ENV_PART 1
/* USB host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#endif
/* USB Host Support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_VF
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
/*
* USB
*/
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_HAS_FSL_DR_USB
#define CONFIG_USB_EHCI_FSL
#define CONFIG_HAS_FSL_MPH_USB
#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
#define CONFIG_AT91_WANTS_COMMON_PHY
/* USB */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_ATMEL
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2
#define CONFIG_HAS_FSL_MPH_USB
#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_EHCI_IS_TDI
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB Host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#endif
#if !defined(CONFIG_USB_XHCI_HCD)
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MARVELL
#define CONFIG_EHCI_IS_TDI
#endif
#define CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS
/* USB UHH support options */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_OMAP
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB2.0 Host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#include "tam3517-common.h"
-#undef CONFIG_USB_EHCI
+#undef CONFIG_USB_EHCI_HCD
#undef CONFIG_USB_EHCI_OMAP
#undef CONFIG_USB_OMAP3
* Common USB/EHCI configuration
*/
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_HCD /* Enable EHCI USB support */
#define CONFIG_USB_EHCI_MARVELL
#define ORION5X_USB20_HOST_PORT_BASE ORION5X_USB20_PORT0_BASE
#define CONFIG_SUPPORT_VFAT
#define CONFIG_SYS_I2C_SPEED 100000
/* USB Configs */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_SYS_INIT_SP_ADDR CONFIG_IRAM_STACK
/* USB */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_EXYNOS
#define CONFIG_USB_XHCI_EXYNOS
/* USB Configs */
#ifdef CONFIG_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_SYS_I2C_POWERIC_ADDR 0x58 /* da9063 */
/* USB */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_RMOBILE
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_ENV_SIZE 0x4000
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_ARMADA100
#define CONFIG_EHCI_IS_TDI
#endif /* CONFIG_CMD_USB */
#define CONFIG_ARP_TIMEOUT 200UL
/* USB Configs */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_ENV_OFFSET (SZ_512M - SZ_128K) /* 128K sector size */
/* USB Host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB Host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_SYS_I2C_POWERIC_ADDR 0x58 /* da9063 */
/* USB */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_RMOBILE
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_SYS_TMU_CLK_DIV 4
/* USB */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_RMOBILE
#define CONFIG_USB_MAX_CONTROLLER_COUNT 3
/* USB Configs */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_STORAGE
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
/*#define CONFIG_HAS_FSL_DR_USB*/
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
/*#define CONFIG_HAS_FSL_DR_USB*/
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
/*#define CONFIG_HAS_FSL_DR_USB*/
#ifdef CONFIG_HAS_FSL_DR_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#endif
/*
* USB/EHCI
*/
-#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_HCD /* Enable EHCI USB support */
#define CONFIG_USB_EHCI_PPC4XX /* on PPC4xx platform */
#define CONFIG_SYS_PPC4XX_USB_ADDR 0xe0000300
#define CONFIG_EHCI_MMIO_BIG_ENDIAN
* USB
*/
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX5
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
* USB
*/
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_ATMEL
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
"128k@0x19C0000(swupdate-kernel-dtb.nor)"
/* USB Configs */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_STORAGE
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_ENV_OFFSET (SZ_512M - SZ_128K) /* 128K sectors */
/* USB host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
*/
#if defined(CONFIG_CMD_USB)
-#define CONFIG_USB_EHCI /* Enable EHCI Support */
+#define CONFIG_USB_EHCI_HCD /* Enable EHCI Support */
#define CONFIG_USB_EHCI_FSL /* On a FSL platform */
#define CONFIG_EHCI_MMIO_BIG_ENDIAN /* With big-endian regs */
#define CONFIG_EHCI_DESC_BIG_ENDIAN
* Common USB/EHCI configuration
*/
#if defined(CONFIG_CMD_USB) && !defined(CONFIG_DM)
-#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_HCD /* Enable EHCI USB support */
#define CONFIG_SUPPORT_VFAT
#endif /* CONFIG_CMD_USB */
#define CONFIG_SYS_NAND_LARGEPAGE
/* EHCI driver */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 1
#define CONFIG_EHCI_IS_TDI
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_FEC_MXC_PHYADDR 0x1F
/* USB Configs */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX5
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_FEC_MXC_PHYADDR 0x1F
/* USB Configs */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX5
#define CONFIG_USB_STORAGE
#define CONFIG_USB_HOST_ETHER
#define CONFIG_FEC_MXC_PHYADDR 0x1F
/* USB Configs */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX5
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_IMX_VIDEO_SKIP
/* USB */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
/* USB Configs */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_HOST_ETHER
#define CONFIG_MMCROOT "/dev/mmcblk0p2"
/* USB Configs */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
/* USB Configs */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_HOST_ETHER
/* USB Configs */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_HOST_ETHER
#define CONFIG_PHY_ATHEROS
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_HOST_ETHER
#define CONFIG_PHY_ATHEROS
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_HOST_ETHER
/* USB Configs */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
/* USB */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MXS
#define CONFIG_EHCI_IS_TDI
#endif
* USB/EHCI
*/
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_HCD /* Enable EHCI USB support */
#define CONFIG_USB_EHCI_KIRKWOOD /* on Kirkwood platform */
#define CONFIG_EHCI_IS_TDI
#define CONFIG_SUPPORT_VFAT
#define CONFIG_PHY_MICREL_KSZ9021
/* USB Configs */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
/* USB Configs */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP
#define CONFIG_USB_HOST_ETHER
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB Host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_LIB_HW_RAND
/* USB */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_EXYNOS
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#define CONFIG_DEFAULT_CONSOLE "console=ttySAC2,115200n8\0"
/* USB */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_EXYNOS
/* DFU */
#define CONFIG_FASTBOOT_BUF_SIZE 0x07000000
/* USB EHCI */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_OMAP
#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 147
#define CONFIG_TWL4030_LED
/* USB EHCI */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_OMAP
#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 183
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
*/
/* USB UHH support options */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_OMAP
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#define CONFIG_SYS_I2C_TCA642X_ADDR 0x22
/* USB UHH support options */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_OMAP
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_SYS_FSL_USDHC_NUM 2
/* USB Configs */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_HAS_FSL_DR_USB
#if defined(CONFIG_HAS_FSL_DR_USB)
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#endif
#define CONFIG_HAS_FSL_DR_USB
#if defined(CONFIG_HAS_FSL_DR_USB)
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#endif
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB2.0 Host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB2.0 Host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB2.0 Host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_SYS_MMC_ENV_PART 2
/* USB Host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_SUPPORT_EMMC_BOOT
/* USB Configs */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_AT91_WANTS_COMMON_PHY
/* USB */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_ATMEL
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2
#define CONFIG_PHYLIB
/* USB config */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_MXC_USB_PORT 1
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_ENV_OFFSET (SZ_512M - SZ_128K) /* 128K sectors */
/* USB host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_SYS_I2C_POWERIC_ADDR 0x58 /* da9063 */
/* USB */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_RMOBILE
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_CMD_USB
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_ATMEL
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#endif
#define CONFIG_SYS_MMC_ENV_PART 2
/* USB Host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
/* USB */
#ifdef CONFIG_440EPX
-#undef CONFIG_USB_EHCI /* OHCI by default */
+#undef CONFIG_USB_EHCI_HCD /* OHCI by default */
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_PPC4XX
#define CONFIG_SYS_PPC4XX_USB_ADDR 0xe0000300
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_EHCI_MMIO_BIG_ENDIAN
#define CONFIG_EHCI_DESC_BIG_ENDIAN
-#else /* CONFIG_USB_EHCI */
+#else /* CONFIG_USB_EHCI_HCD */
#define CONFIG_USB_OHCI_NEW
#define CONFIG_SYS_OHCI_BE_CONTROLLER
#define CONFIG_SYS_I2C_POWERIC_ADDR 0x58 /* da9063 */
/* USB */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_RMOBILE
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_TFTP_TSIZE
/* USB */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_ATMEL
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2
#define CONFIG_SYS_TMU_CLK_DIV 4
/* USB */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_RMOBILE
#define CONFIG_USB_MAX_CONTROLLER_COUNT 3
* A10 specific configuration
*/
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_SUNXI
#endif
* A64 specific configuration
*/
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_SUNXI
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
#endif
* High Level Configuration Options
*/
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_SUNXI
#endif
* A31 specific configuration
*/
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_SUNXI
#endif
* A20 specific configuration
*/
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_SUNXI
#endif
* A23 specific configuration
*/
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_SUNXI
#endif
*/
/* USB EHCI */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_OMAP
#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 162
/* USB */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB Host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_ENV_OFFSET (SZ_512M - SZ_128K) /* 128K sectors */
/* USB host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#endif
/* remove USB */
-#ifdef CONFIG_USB_EHCI
-#undef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
+#undef CONFIG_USB_EHCI_HCD
#endif
#ifdef CONFIG_USB_EHCI_TEGRA
#undef CONFIG_USB_EHCI_TEGRA
#define CONFIG_PHY_MICREL_KSZ9021
/* USB Configs */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_MXC_USB_PORT 1
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
/* USB Configs */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_SMSC95XX
#define CONFIG_ENV_OFFSET (SZ_1M - CONFIG_ENV_SIZE)
/* USB Host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_SYS_FSL_ESDHC_NUM 1
/* USB */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX5
#define CONFIG_MXC_USB_PORT 1
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
/*
* USB/EHCI
*/
-#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_HCD /* Enable EHCI USB support */
#define CONFIG_USB_EHCI_VCT /* on VCT platform */
#define CONFIG_EHCI_MMIO_BIG_ENDIAN
#define CONFIG_EHCI_DESC_BIG_ENDIAN
#define CONFIG_SPI_FLASH_SIZE (4 << 20)
/* USB Host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_SYS_MMC_ENV_PART 2
/* USB Host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
/* USB */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_ATMEL
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#endif
#define CONFIG_PHY_ATHEROS
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_HOST_ETHER
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
/* USB Configs */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
/* USB Configs */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_SYS_MMC_ENV_PART 2
/* USB Host support */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_TEGRA
/* USB networking support */
#define CONFIG_FPGA_COUNT 1
/* USB EHCI options */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_SPEAR
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
/*-----------------------------------------------------------------------
* USB configuration
*/
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_PCI
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 12
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
/*
* USB
*/
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MMCROOT "/dev/mmcblk0p2" /* USDHC2 */
/* USB Configs */
-#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_MX6
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
* USB
*/
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_HCD /* Enable EHCI USB support */
#define CONFIG_USB_EHCI_MXC
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORT 1
int submit_int_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
int transfer_len, int interval);
-#if defined CONFIG_USB_EHCI || defined CONFIG_USB_MUSB_HOST || defined(CONFIG_DM_USB)
+#if defined CONFIG_USB_EHCI_HCD || defined CONFIG_USB_MUSB_HOST \
+ || defined(CONFIG_DM_USB)
struct int_queue *create_int_queue(struct usb_device *dev, unsigned long pipe,
int queuesize, int elementsize, void *buffer, int interval);
int destroy_int_queue(struct usb_device *dev, struct int_queue *queue);