TQM5200: remove dead code

This board never used a MGT5100 processor.

Signed-off-by: Wolfgang Denk <wd@denx.de>

diff --git a/board/tqm5200/tqm5200.c b/board/tqm5200/tqm5200.c
index 33ad2a32a54d0485d66d0e7a433ea8a51acea9bf..e67145eb5be562eeb4790567b5b43cf225e5f63c 100644 (file)
--- a/board/tqm5200/tqm5200.c
+++ b/board/tqm5200/tqm5200.c
@@ -104,7 +104,6 @@ static void sdram_start (int hi_addr)
  *           is something else than 0x00000000.
  */
 
-#if defined(CONFIG_MPC5200)
 long int initdram (int board_type)
 {
        ulong dramsize = 0;
@@ -230,57 +229,6 @@ long int initdram (int board_type)
 #endif /* CONFIG_TQM5200_B */
 }
 
-#elif defined(CONFIG_MGT5100)
-
-long int initdram (int board_type)
-{
-       ulong dramsize = 0;
-#ifndef CFG_RAMBOOT
-       ulong test1, test2;
-
-       /* setup and enable SDRAM chip selects */
-       *(vu_long *)MPC5XXX_SDRAM_START = 0x00000000;
-       *(vu_long *)MPC5XXX_SDRAM_STOP = 0x0000ffff;/* 2G */
-       *(vu_long *)MPC5XXX_ADDECR |= (1 << 22); /* Enable SDRAM */
-       __asm__ volatile ("sync");
-
-       /* setup config registers */
-       *(vu_long *)MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
-       *(vu_long *)MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
-
-       /* address select register */
-       *(vu_long *)MPC5XXX_SDRAM_XLBSEL = SDRAM_ADDRSEL;
-       __asm__ volatile ("sync");
-
-       /* find RAM size */
-       sdram_start(0);
-       test1 = get_ram_size((ulong *)CFG_SDRAM_BASE, 0x80000000);
-       sdram_start(1);
-       test2 = get_ram_size((ulong *)CFG_SDRAM_BASE, 0x80000000);
-       if (test1 > test2) {
-               sdram_start(0);
-               dramsize = test1;
-       } else {
-               dramsize = test2;
-       }
-
-       /* set SDRAM end address according to size */
-       *(vu_long *)MPC5XXX_SDRAM_STOP = ((dramsize - 1) >> 15);
-
-#else /* CFG_RAMBOOT */
-
-       /* Retrieve amount of SDRAM available */
-       dramsize = ((*(vu_long *)MPC5XXX_SDRAM_STOP + 1) << 15);
-
-#endif /* CFG_RAMBOOT */
-
-       return dramsize;
-}
-
-#else
-#error Neither CONFIG_MPC5200 or CONFIG_MGT5100 defined
-#endif
-
 int checkboard (void)
 {
 #if defined(CONFIG_AEVFIFO)
@@ -323,10 +271,6 @@ void flash_preinit(void)
         * Note that CS_BOOT cannot be cleared when
         * executing in flash.
         */
-#if defined(CONFIG_MGT5100)
-       *(vu_long *)MPC5XXX_ADDECR &= ~(1 << 25); /* disable CS_BOOT */
-       *(vu_long *)MPC5XXX_ADDECR |= (1 << 16); /* enable CS0 */
-#endif
        *(vu_long *)MPC5XXX_BOOTCS_CFG &= ~0x1; /* clear RO */
 }