debug("\n\n");
+#if defined(CONFIG_DDR_RFDC_FIXED)
+ mtsdram(SDRAM_RFDC, CONFIG_DDR_RFDC_FIXED);
+ size = 512;
+ rffd_average = CONFIG_DDR_RFDC_FIXED & SDRAM_RFDC_RFFD_MASK;
+ mfsdram(SDRAM_RDCC, rdcc); /* record this value */
+ cal->rdcc = rdcc;
+#else /* CONFIG_DDR_RFDC_FIXED */
in_window = 0;
rdcc = 0;
rffd_average = SDRAM_RFDC_RFFD_MAX;
mtsdram(SDRAM_RFDC, rfdc_reg | SDRAM_RFDC_RFFD_ENCODE(rffd_average));
+#endif /* CONFIG_DDR_RFDC_FIXED */
rffd = rffd_average;
in_window = 0;
debug("*** best_result: read value SDRAM_RQDC 0x%08x\n",
rqdc_reg);
+#if defined(CONFIG_DDR_RFDC_FIXED)
+ mtsdram(SDRAM_RFDC, CONFIG_DDR_RFDC_FIXED);
+#else /* CONFIG_DDR_RFDC_FIXED */
mfsdram(SDRAM_RFDC, rfdc_reg);
rfdc_reg &= ~(SDRAM_RFDC_RFFD_MASK);
mtsdram(SDRAM_RFDC, rfdc_reg |
SDRAM_RFDC_RFFD_ENCODE(tcal.autocal.rffd));
+#endif /* CONFIG_DDR_RFDC_FIXED */
mfsdram(SDRAM_RFDC, rfdc_reg);
debug("*** best_result: read value SDRAM_RFDC 0x%08x\n",
COBJS += denali_data_eye.o
COBJS += denali_spd_ddr2.o
COBJS += ecc.o
+ifdef CONFIG_CMD_ECCTEST
+COBJS += cmd_ecctest.o
+endif
COBJS += fdt.o
COBJS += interrupts.o
COBJS += iop480_uart.o
--- /dev/null
+/*
+ * (C) Copyright 2010
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include <ppc4xx.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+#include <asm/cache.h>
+
+#if defined(CONFIG_SDRAM_PPC4xx_IBM_DDR) || \
+ defined(CONFIG_SDRAM_PPC4xx_IBM_DDR2)
+#if defined(CONFIG_DDR_ECC) || defined(CONFIG_SDRAM_ECC)
+
+#if defined(CONFIG_405EX)
+/*
+ * Currently only 405EX uses 16bit data bus width as an alternative
+ * option to 32bit data width (SDRAM0_MCOPT1_WDTH)
+ */
+#define SDRAM_DATA_ALT_WIDTH 2
+#else
+#define SDRAM_DATA_ALT_WIDTH 8
+#endif
+
+#if defined(CONFIG_SYS_OCM_BASE)
+#define CONFIG_FUNC_ISRAM_ADDR CONFIG_SYS_OCM_BASE
+#endif
+
+#if defined(CONFIG_SYS_ISRAM_BASE)
+#define CONFIG_FUNC_ISRAM_ADDR CONFIG_SYS_ISRAM_BASE
+#endif
+
+#if !defined(CONFIG_FUNC_ISRAM_ADDR)
+#error "No internal SRAM/OCM provided!"
+#endif
+
+#define force_inline inline __attribute__ ((always_inline))
+
+static inline void machine_check_disable(void)
+{
+ mtmsr(mfmsr() & ~MSR_ME);
+}
+
+static inline void machine_check_enable(void)
+{
+ mtmsr(mfmsr() | MSR_ME);
+}
+
+/*
+ * These helper functions need to be inlined, since they
+ * are called from the functions running from internal SRAM.
+ * SDRAM operation is forbidden at that time, so calling
+ * functions in SDRAM has to be avoided.
+ */
+static force_inline void wait_ddr_idle(void)
+{
+ u32 val;
+
+ do {
+ mfsdram(SDRAM_MCSTAT, val);
+ } while ((val & SDRAM_MCSTAT_IDLE_MASK) == SDRAM_MCSTAT_IDLE_NOT);
+}
+
+static force_inline void recalibrate_ddr(void)
+{
+ u32 val;
+
+ /*
+ * Rewrite RQDC & RFDC to calibrate again. If this is not
+ * done, the SDRAM controller is working correctly after
+ * changing the MCOPT1_MCHK bits.
+ */
+ mfsdram(SDRAM_RQDC, val);
+ mtsdram(SDRAM_RQDC, val);
+ mfsdram(SDRAM_RFDC, val);
+ mtsdram(SDRAM_RFDC, val);
+}
+
+static force_inline void set_mcopt1_mchk(u32 bits)
+{
+ u32 val;
+
+ wait_ddr_idle();
+ mfsdram(SDRAM_MCOPT1, val);
+ mtsdram(SDRAM_MCOPT1, (val & ~SDRAM_MCOPT1_MCHK_MASK) | bits);
+ recalibrate_ddr();
+}
+
+/*
+ * The next 2 functions are copied to internal SRAM/OCM and run
+ * there. No function calls allowed here. No SDRAM acitivity should
+ * be done here.
+ */
+static void inject_ecc_error(void *ptr, int par)
+{
+ u32 val;
+
+ /*
+ * Taken from PPC460EX/EXr/GT users manual (Rev 1.21)
+ * 22.2.17.13 ECC Diagnostics
+ *
+ * Items 1 ... 5 are already done by now, running from RAM
+ * with ECC enabled
+ */
+
+ out_be32(ptr, 0x00000000);
+ val = in_be32(ptr);
+
+ /* 6. Set memory controller to no error checking */
+ set_mcopt1_mchk(SDRAM_MCOPT1_MCHK_NON);
+
+ /* 7. Modify one or two bits for error simulation */
+ if (par == 1)
+ out_be32(ptr, in_be32(ptr) ^ 0x00000001);
+ else
+ out_be32(ptr, in_be32(ptr) ^ 0x00000003);
+
+ /* 8. Wait for SDRAM idle */
+ val = in_be32(ptr);
+ set_mcopt1_mchk(SDRAM_MCOPT1_MCHK_CHK_REP);
+
+ /* Wait for SDRAM idle */
+ wait_ddr_idle();
+
+ /* Continue with 9. in calling function... */
+}
+
+static void rewrite_ecc_parity(void *ptr, int par)
+{
+ u32 current_address = (u32)ptr;
+ u32 end_address;
+ u32 address_increment;
+ u32 mcopt1;
+ u32 val;
+
+ /*
+ * Fill ECC parity byte again. Otherwise further accesses to
+ * the failure address will result in exceptions.
+ */
+
+ /* Wait for SDRAM idle */
+ val = in_be32(0x00000000);
+ set_mcopt1_mchk(SDRAM_MCOPT1_MCHK_GEN);
+
+ /* ECC bit set method for non-cached memory */
+ mfsdram(SDRAM_MCOPT1, mcopt1);
+ if ((mcopt1 & SDRAM_MCOPT1_DMWD_MASK) == SDRAM_MCOPT1_DMWD_32)
+ address_increment = 4;
+ else
+ address_increment = SDRAM_DATA_ALT_WIDTH;
+ end_address = current_address + CONFIG_SYS_CACHELINE_SIZE;
+
+ while (current_address < end_address) {
+ *((unsigned long *)current_address) = 0;
+ current_address += address_increment;
+ }
+
+ set_mcopt1_mchk(SDRAM_MCOPT1_MCHK_CHK_REP);
+
+ /* Wait for SDRAM idle */
+ wait_ddr_idle();
+}
+
+static int do_ecctest(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ u32 old_val;
+ u32 val;
+ u32 *ptr;
+ void (*sram_func)(u32 *, int);
+ int error;
+
+ if (argc < 3) {
+ cmd_usage(cmdtp);
+ return 1;
+ }
+
+ ptr = (u32 *)simple_strtoul(argv[1], NULL, 16);
+ error = simple_strtoul(argv[2], NULL, 16);
+ if ((error < 1) || (error > 2)) {
+ cmd_usage(cmdtp);
+ return 1;
+ }
+
+ printf("Using address %p for %d bit ECC error injection\n",
+ ptr, error);
+
+ /*
+ * Save value to restore it later on
+ */
+ old_val = in_be32(ptr);
+
+ /*
+ * Copy ECC injection function into internal SRAM/OCM
+ */
+ sram_func = (void *)CONFIG_FUNC_ISRAM_ADDR;
+ memcpy((void *)CONFIG_FUNC_ISRAM_ADDR, inject_ecc_error, 0x10000);
+
+ /*
+ * Disable interrupts and exceptions before calling this
+ * function in internal SRAM/OCM
+ */
+ disable_interrupts();
+ machine_check_disable();
+ eieio();
+
+ /*
+ * Jump to ECC simulation function in internal SRAM/OCM
+ */
+ (*sram_func)(ptr, error);
+
+ /* 10. Read the corresponding address */
+ val = in_be32(ptr);
+
+ /*
+ * Read and print ECC status register/info:
+ * The faulting address is only known upon uncorrectable ECC
+ * errors.
+ */
+ mfsdram(SDRAM_ECCES, val);
+ if (val & SDRAM_ECCES_CE)
+ printf("ECC: Correctable error\n");
+ if (val & SDRAM_ECCES_UE) {
+ printf("ECC: Uncorrectable error at 0x%02x%08x\n",
+ mfdcr(SDRAM_ERRADDULL), mfdcr(SDRAM_ERRADDLLL));
+ }
+
+ /*
+ * Clear pending interrupts/exceptions
+ */
+ mtsdram(SDRAM_ECCES, 0xffffffff);
+ mtdcr(SDRAM_ERRSTATLL, 0xff000000);
+ set_mcsr(get_mcsr());
+
+ /* Now enable interrupts and exceptions again */
+ eieio();
+ machine_check_enable();
+ enable_interrupts();
+
+ /*
+ * The ECC parity byte need to be re-written for the
+ * corresponding address. Otherwise future accesses to it
+ * will result in exceptions.
+ *
+ * Jump to ECC parity generation function
+ */
+ memcpy((void *)CONFIG_FUNC_ISRAM_ADDR, rewrite_ecc_parity, 0x10000);
+ (*sram_func)(ptr, 0);
+
+ /*
+ * Restore value in corresponding address
+ */
+ out_be32(ptr, old_val);
+
+ return 0;
+}
+
+U_BOOT_CMD(
+ ecctest, 3, 0, do_ecctest,
+ "Test ECC by single and double error bit injection",
+ "address 1/2"
+);
+
+#endif /* defined(CONFIG_DDR_ECC) || defined(CONFIG_SDRAM_ECC) */
+#endif /* defined(CONFIG_SDRAM_PPC4xx_IBM_DDR)... */
/* clear ECC error repoting registers */
mtsdram(SDRAM_ECCES, 0xffffffff);
- mtdcr(0x4c, 0xffffffff);
+#if defined(CONFIG_SDRAM_PPC4xx_IBM_DDR)
+ /*
+ * IBM DDR(1) core (440GX):
+ * Clear Mx bits in SDRAM0_BESR0/1
+ */
+ mtsdram(SDRAM0_BESR0, 0xffffffff);
+ mtsdram(SDRAM0_BESR1, 0xffffffff);
+#elif defined(CONFIG_440)
+ /*
+ * 440/460 DDR2 core:
+ * Clear EMID (Error PLB Master ID) in MQ0_ESL
+ */
+ mtdcr(SDRAM_ERRSTATLL, 0xfff00000);
+#else
+ /*
+ * 405EX(r) DDR2 core:
+ * Clear M0ID (Error PLB Master ID) in SDRAM_BESR
+ */
+ mtsdram(SDRAM_BESR, 0xf0000000);
+#endif
mtsdram(SDRAM_MCOPT1,
(mcopt1 & ~SDRAM_MCOPT1_MCHK_MASK) | SDRAM_MCOPT1_MCHK_CHK_REP);
/* Clear MCSR */
mtspr(SPRN_MCSR, val);
}
+
+#if defined(CONFIG_DDR_ECC) && defined(CONFIG_SDRAM_PPC4xx_IBM_DDR2)
+ /*
+ * Read and print ECC status register/info:
+ * The faulting address is only known upon uncorrectable ECC
+ * errors.
+ */
+ mfsdram(SDRAM_ECCES, val);
+ if (val & SDRAM_ECCES_CE)
+ printf("ECC: Correctable error\n");
+ if (val & SDRAM_ECCES_UE) {
+ printf("ECC: Uncorrectable error at 0x%02x%08x\n",
+ mfdcr(SDRAM_ERRADDULL), mfdcr(SDRAM_ERRADDLLL));
+ }
+#endif /* CONFIG_DDR_ECC ... */
+
#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
mfsdram(DDR0_00, val) ;
printf("DDR0: DDR0_00 %lx\n", val);
#define SDRAM_CFG0 0x20 /* memory controller options 0 */
#define SDRAM_CFG1 0x21 /* memory controller options 1 */
+#define SDRAM0_BESR0 0x0000 /* bus error status reg 0 */
+#define SDRAM0_BESR1 0x0008 /* bus error status reg 1 */
#define SDRAM0_BEAR 0x0010 /* bus error address reg */
#define SDRAM0_SLIO 0x0018 /* ddr sdram slave interface options */
#define SDRAM0_CFG0 0x0020 /* ddr sdram options 0 */
/*
* Memory controller registers
*/
+#ifdef CONFIG_405EX
#define SDRAM_BESR 0x00 /* PLB bus error status (read/clear) */
#define SDRAM_BESRT 0x01 /* PLB bus error status (test/set) */
#define SDRAM_BEARL 0x02 /* PLB bus error address low */
#define SDRAM_WMIRQT 0x07 /* PLB write master interrupt (test/set) */
#define SDRAM_PLBOPT 0x08 /* PLB slave options */
#define SDRAM_PUABA 0x09 /* PLB upper address base */
-#ifndef CONFIG_405EX
-#define SDRAM_MCSTAT 0x14 /* memory controller status */
-#else
#define SDRAM_MCSTAT 0x1F /* memory controller status */
-#endif
+#else /* CONFIG_405EX */
+#define SDRAM_MCSTAT 0x14 /* memory controller status */
+#endif /* CONFIG_405EX */
#define SDRAM_MCOPT1 0x20 /* memory controller options 1 */
#define SDRAM_MCOPT2 0x21 /* memory controller options 2 */
#define SDRAM_MODT0 0x22 /* on die termination for bank 0 */
DECLARE_GLOBAL_DATA_PTR;
-#define CONFIG_SYS_BCSR3_PCIE 0x10
+ struct board_bcsr {
+ u8 board_id;
+ u8 cpld_rev;
+ u8 led_user;
+ u8 board_status;
+ u8 reset_ctrl;
+ u8 flash_ctrl;
+ u8 eth_ctrl;
+ u8 usb_ctrl;
+ u8 irq_ctrl;
+};
#define BOARD_CANYONLANDS_PCIE 1
#define BOARD_CANYONLANDS_SATA 2
{
#if !defined(CONFIG_ARCHES)
u32 sdr0_cust0;
+ struct board_bcsr *bcsr_data =
+ (struct board_bcsr *)CONFIG_SYS_BCSR_BASE;
+
#endif
/*
#if !defined(CONFIG_ARCHES)
/* Enable ethernet and take out of reset */
- out_8((void *)CONFIG_SYS_BCSR_BASE + 6, 0);
+ out_8(&bcsr_data->eth_ctrl, 0) ;
/* Remove NOR-FLASH, NAND-FLASH & EEPROM hardware write protection */
- out_8((void *)CONFIG_SYS_BCSR_BASE + 5, 0);
-
- /* Enable USB host & USB-OTG */
- out_8((void *)CONFIG_SYS_BCSR_BASE + 7, 0);
-
+ out_8(&bcsr_data->flash_ctrl, 0) ;
mtsdr(SDR0_SRST1, 0); /* Pull AHB out of reset default=1 */
/* Setup PLB4-AHB bridge based on the system address map */
return 0;
}
+#if defined(CONFIG_USB_OHCI_NEW) && defined(CONFIG_SYS_USB_OHCI_BOARD_INIT)
+int usb_board_init(void)
+{
+ struct board_bcsr *bcsr_data =
+ (struct board_bcsr *)CONFIG_SYS_BCSR_BASE;
+ u8 val;
+
+ /* Enable USB host & USB-OTG */
+ val = in_8(&bcsr_data->usb_ctrl);
+ val &= ~(BCSR_USBCTRL_OTG_RST | BCSR_USBCTRL_HOST_RST);
+ out_8(&bcsr_data->usb_ctrl, val);
+
+ return 0;
+}
+
+int usb_board_stop(void)
+{
+ struct board_bcsr *bcsr_data =
+ (struct board_bcsr *)CONFIG_SYS_BCSR_BASE;
+ u8 val;
+
+ /* Disable USB host & USB-OTG */
+ val = in_8(&bcsr_data->usb_ctrl);
+ val |= (BCSR_USBCTRL_OTG_RST | BCSR_USBCTRL_HOST_RST);
+ out_8(&bcsr_data->usb_ctrl, val);
+
+ return 0;
+}
+
+int usb_board_init_fail(void)
+{
+ return usb_board_stop();
+}
+#endif /* CONFIG_USB_OHCI_NEW && CONFIG_SYS_USB_OHCI_BOARD_INIT */
+
#if !defined(CONFIG_ARCHES)
static void canyonlands_sata_init(int board_type)
{
#if !defined(CONFIG_ARCHES)
int checkboard(void)
{
+ struct board_bcsr *bcsr_data =
+ (struct board_bcsr *)CONFIG_SYS_BCSR_BASE;
char *s = getenv("serial#");
if (pvr_460ex()) {
printf("Board: Canyonlands - AMCC PPC460EX Evaluation Board");
- if (in_8((void *)(CONFIG_SYS_BCSR_BASE + 3)) & CONFIG_SYS_BCSR3_PCIE)
+ if (in_8(&bcsr_data->board_status) & BCSR_SELECT_PCIE)
gd->board_type = BOARD_CANYONLANDS_PCIE;
else
gd->board_type = BOARD_CANYONLANDS_SATA;
break;
}
- printf(", Rev. %X", in_8((void *)(CONFIG_SYS_BCSR_BASE + 0)));
+ printf(", Rev. %X", in_8(&bcsr_data->cpld_rev));
if (s != NULL) {
puts(", serial# ");
struct ppc4xx_config ppc4xx_config_val[] = {
{
- "600", "CPU: 600 PLB: 200 OPB: 100 EBC: 100",
+ "600-67", "CPU: 600 PLB: 200 OPB: 67 EBC: 67",
+ {
+ 0x86, 0x80, 0xce, 0x1f, 0x7d, 0x80, 0x00, 0xe0,
+ 0x40, 0x08, 0x23, 0x50, 0x0d, 0x05, 0x00, 0x00
+ }
+ },
+ {
+ "600-100", "CPU: 600 PLB: 200 OPB: 100 EBC: 100",
{
0x86, 0x80, 0xce, 0x1f, 0x79, 0x80, 0x00, 0xa0,
0x40, 0x08, 0x23, 0x50, 0x0d, 0x05, 0x00, 0x00
}
},
+ {
+ "667", "CPU: 667 PLB: 166 OPB: 83 EBC: 83",
+ {
+ 0x06, 0x80, 0xbb, 0x14, 0x99, 0x82, 0x00, 0xa0,
+ 0x40, 0x88, 0x23, 0x50, 0x0d, 0x05, 0x00, 0x00
+ }
+ },
{
"800", "CPU: 800 PLB: 200 OPB: 100 EBC: 100",
{
tlbentry(CONFIG_SYS_PCIE_BASE, SZ_16K, 0x08010000, 0xc, AC_RW | SA_IG)
/* TLB-entry for FPGA(s) */
- tlbentry(CONFIG_SYS_FPGA1_BASE, SZ_1M, CONFIG_SYS_FPGA1_BASE, 4,
+ tlbentry(CONFIG_SYS_FPGA1_BASE, SZ_16M, CONFIG_SYS_FPGA1_BASE, 4,
AC_RW | SA_IG)
- tlbentry(CONFIG_SYS_FPGA2_BASE, SZ_1M, CONFIG_SYS_FPGA2_BASE, 4,
+ tlbentry(CONFIG_SYS_FPGA1_BASE + (16 << 20), SZ_16M,
+ CONFIG_SYS_FPGA1_BASE + (16 << 20), 4, AC_RW | SA_IG)
+ tlbentry(CONFIG_SYS_FPGA2_BASE, SZ_16M, CONFIG_SYS_FPGA2_BASE, 4,
AC_RW | SA_IG)
- tlbentry(CONFIG_SYS_FPGA3_BASE, SZ_1M, CONFIG_SYS_FPGA3_BASE, 4,
+ tlbentry(CONFIG_SYS_FPGA3_BASE, SZ_16M, CONFIG_SYS_FPGA3_BASE, 4,
AC_RW | SA_IG)
/* TLB-entry for OCM */
mtdcr(UIC1SR, 0xffffffff); /* clear all */
mtdcr(UIC1ER, 0x00000000); /* disable all */
mtdcr(UIC1CR, 0x00000000); /* all non-critical */
- mtdcr(UIC1PR, 0xffffffff); /* per ref-board manual */
+ mtdcr(UIC1PR, 0x7fffffff); /* per ref-board manual */
mtdcr(UIC1TR, 0x00000000); /* per ref-board manual */
mtdcr(UIC1VR, 0x00000000); /* int31 highest, base=0x000 */
mtdcr(UIC1SR, 0xffffffff); /* clear all */
#define CONFIG_SYS_PCIE0_XCFGBASE 0xc3000000
#define CONFIG_SYS_PCIE1_XCFGBASE 0xc3001000
+/*
+ * BCSR bits as defined in the Canyonlands board user manual.
+ */
+#define BCSR_USBCTRL_OTG_RST 0x32
+#define BCSR_USBCTRL_HOST_RST 0x01
+#define BCSR_SELECT_PCIE 0x10
+
#define CONFIG_SYS_PCIE0_UTLBASE 0xc08010000ULL /* 36bit physical addr */
/* base address of inbound PCIe window */
#define CONFIG_SYS_USB_OHCI_REGS_BASE (CONFIG_SYS_AHB_BASE | 0xd0000)
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
+#define CONFIG_SYS_USB_OHCI_BOARD_INIT
#endif
/*
*/
#define CONFIG_CMD_CHIP_CONFIG
#define CONFIG_CMD_DATE
+#define CONFIG_CMD_ECCTEST
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_CMD_PCI
#define CONFIG_SYS_FLASH_SIZE (64 << 20)
#define CONFIG_SYS_FPGA1_BASE 0xe0000000
-#define CONFIG_SYS_FPGA2_BASE 0xe0100000
-#define CONFIG_SYS_FPGA3_BASE 0xe0200000
+#define CONFIG_SYS_FPGA2_BASE 0xe2000000
+#define CONFIG_SYS_FPGA3_BASE 0xe4000000
#define CONFIG_SYS_BOOT_BASE_ADDR 0xFF000000 /* EBC Boot Space */
#define CONFIG_SYS_FLASH_BASE_PHYS_H 0x4
(((u64)CONFIG_SYS_FLASH_BASE_PHYS_H << 32) \
| (u64)CONFIG_SYS_FLASH_BASE_PHYS_L)
-#define CONFIG_SYS_OCM_BASE 0xE3000000 /* OCM: 64k */
+#define CONFIG_SYS_OCM_BASE 0xE7000000 /* OCM: 64k */
#define CONFIG_SYS_SRAM_BASE 0xE8000000 /* SRAM: 256k */
#define CONFIG_SYS_LOCAL_CONF_REGS 0xEF000000
#define CONFIG_SYS_PERIPHERAL_BASE 0xEF600000 /* internal periph. */
-#define CONFIG_SYS_AHB_BASE 0xE2000000 /* int. AHB periph. */
-
/*
* Initial RAM & stack pointer (placed in OCM)
*/
#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CONFIG_SYS_FLASH_CFI_AMD_RESET 1 /* Use AMD reset cmd */
+#define CONFIG_SYS_CFI_FLASH_STATUS_POLL /* use status poll method */
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
/*
* DDR2 SDRAM
*/
+#define CONFIG_SYS_MBYTES_SDRAM 256
+#define CONFIG_DDR_ECC
#define CONFIG_AUTOCALIB "silent\0" /* default is non-verbose */
#define CONFIG_PPC4xx_DDR_AUTOCALIBRATION /* IBM DDR autocalibration */
#define DEBUG_PPC4xx_DDR_AUTOCALIBRATION /* dynamic DDR autocal debug */
#undef CONFIG_PPC4xx_DDR_METHOD_A
+#define CONFIG_DDR_RFDC_FIXED 0x000001D7 /* optimal value */
/* DDR1/2 SDRAM Device Control Register Data Values */
/* Memory Queue */
#define CONFIG_SYS_SDRAM_CONF1HB 0x80001C80
#define CONFIG_SYS_SDRAM_CONFPATHB 0x10a68000
-#define CONFIG_DDR_ECC
-#define CONFIG_SYS_MBYTES_SDRAM 256
-
#define CAS_LATENCY JEDEC_MA_MR_CL_DDR2_5_0_CLK
/* DDR1/2 SDRAM Device Control Register Data Values */
* Commands additional to the ones defined in amcc-common.h
*/
#define CONFIG_CMD_CHIP_CONFIG
+#define CONFIG_CMD_ECCTEST
#define CONFIG_CMD_PCI
#define CONFIG_CMD_SDRAM
#define CONFIG_SYS_EBC_PB1AP (EBC_BXAP_BME_DISABLED | \
EBC_BXAP_TWT_ENCODE(5) | \
EBC_BXAP_CSN_ENCODE(0) | \
- EBC_BXAP_OEN_ENCODE(4) | \
+ EBC_BXAP_OEN_ENCODE(3) | \
EBC_BXAP_WBN_ENCODE(0) | \
EBC_BXAP_WBF_ENCODE(0) | \
EBC_BXAP_TH_ENCODE(1) | \
EBC_BXAP_BEM_RW | \
EBC_BXAP_PEN_DISABLED)
#define CONFIG_SYS_EBC_PB1CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FPGA1_BASE) | \
- EBC_BXCR_BS_1MB | \
+ EBC_BXCR_BS_32MB | \
EBC_BXCR_BU_RW | \
EBC_BXCR_BW_32BIT)
#define CONFIG_SYS_EBC_PB2AP (EBC_BXAP_BME_DISABLED | \
EBC_BXAP_TWT_ENCODE(5) | \
EBC_BXAP_CSN_ENCODE(0) | \
- EBC_BXAP_OEN_ENCODE(4) | \
+ EBC_BXAP_OEN_ENCODE(3) | \
EBC_BXAP_WBN_ENCODE(0) | \
EBC_BXAP_WBF_ENCODE(0) | \
EBC_BXAP_TH_ENCODE(1) | \
EBC_BXAP_BEM_RW | \
EBC_BXAP_PEN_DISABLED)
#define CONFIG_SYS_EBC_PB2CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FPGA2_BASE) | \
- EBC_BXCR_BS_1MB | \
+ EBC_BXCR_BS_16MB | \
EBC_BXCR_BU_RW | \
EBC_BXCR_BW_32BIT)
#define CONFIG_SYS_EBC_PB3AP (EBC_BXAP_BME_DISABLED | \
EBC_BXAP_TWT_ENCODE(5) | \
EBC_BXAP_CSN_ENCODE(0) | \
- EBC_BXAP_OEN_ENCODE(4) | \
+ EBC_BXAP_OEN_ENCODE(3) | \
EBC_BXAP_WBN_ENCODE(0) | \
EBC_BXAP_WBF_ENCODE(0) | \
EBC_BXAP_TH_ENCODE(1) | \
EBC_BXAP_BEM_RW | \
EBC_BXAP_PEN_DISABLED)
#define CONFIG_SYS_EBC_PB3CR (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FPGA3_BASE) | \
- EBC_BXCR_BS_1MB | \
+ EBC_BXCR_BS_16MB | \
EBC_BXCR_BU_RW | \
EBC_BXCR_BW_32BIT)
projects / u-boot / commitdiff