+++ /dev/null
-if TARGET_EBONY
-
-config SYS_BOARD
- default "ebony"
-
-config SYS_VENDOR
- default "amcc"
-
-config SYS_CONFIG_NAME
- default "ebony"
-
-config DISPLAY_BOARDINFO
- bool
- default y
-
-endif
+++ /dev/null
-EBONY BOARD
-M: Stefan Roese <sr@denx.de>
-S: Maintained
-F: board/amcc/ebony/
-F: include/configs/ebony.h
-F: configs/ebony_defconfig
+++ /dev/null
-#
-# (C) Copyright 2002-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = ebony.o flash.o
-extra-y += init.o
+++ /dev/null
- AMCC Ebony Board
-
- Last Update: September 12, 2002
-=======================================================================
-
-This file contains some handy info regarding U-Boot and the AMCC
-Ebony evaluation board. See the README.ppc440 for additional
-information.
-
-
-SWITCH SETTINGS & JUMPERS
-==========================
-
-Here's what I've been using successfully. If you feel inclined to
-change things ... please read the docs!
-
-DIPSW U46 U80
-------------------------
-SW 1 off on
-SW 2 on on
-SW 3 on on
-SW 4 off on
-SW 5 on off
-SW 6 on on
-SW 7 on off
-SW 8 on off
-
-J41: strapped
-J42: open
-
-All others are factory default.
-
-
-I2C probe
-=====================
-
-The i2c utilities have been tested on both Rev B. and Rev C. and
-look good. The CONFIG_SYS_I2C_NOPROBES macro is defined to prevent
-probing the CDCV850 clock controller at address 0x69 (since reading
-it causes the i2c implementation to misbehave. The output of
-'i2c probe' should look like this (assuming you are only using a single
-SO-DIMM:
-
-=> i2c probe
-Valid chip addresses: 50 53 54
-Excluded chip addresses: 69
-
-
-GETTING OUT OF I2C TROUBLE
-===========================
-
-If you're like me ... you may have screwed up your bootstrap serial
-eeprom ... or worse, your SPD eeprom when experimenting with the
-i2c commands. If so, here are some ideas on how to get out of
-trouble:
-
-Serial bootstrap eeprom corruption:
------------------------------------
-Power down the board and set the following straps:
-
-J41 - open
-J42 - strapped
-
-This will select the default sys0 and sys1 settings (the serial
-eeproms are not used). Then power up the board and fix the serial
-eeprom using the 'i2c mm' command. Here are the values I currently
-use:
-
-=> i2c md 50 0 10
-0000: bf a2 04 01 ae 94 11 00 00 00 00 00 00 00 00 00 ................
-
-=> i2c md 54 0 10
-0000: 8f b3 24 01 4d 14 11 00 00 00 00 00 00 00 00 00 ..$.M...........
-
-Once you have the eeproms set correctly change the
-J41/J42 straps as you desire.
-
-SPD eeprom corruption:
-------------------------
-I've corrupted the SPD eeprom several times ... perhaps too much coffee
-and not enough presence of mind ;-). By default, the ebony code uses
-the SPD to initialize the DDR SDRAM control registers. So if the SPD
-eeprom is corrupted, U-Boot will never get into ram. Here's how I got
-out of this situation:
-
-0. First, _before_ playing with the i2c utilities, do an 'i2c probe', then
-use 'i2c md' to capture the various device contents to a file. Some day
-you may be glad you did this ... trust me :-). Otherwise try the
-following:
-
-1. In the include/configs/EBONY.h file find the line that defines
-the CONFIG_SPD_EEPROM macro and undefine it. E.g:
-
-#undef CONFIG_SPD_EEPROM
-
-This will make the code use default SDRAM control register
-settings without using the SPD eeprom.
-
-2. Rebuild U-Boot
-
-3. Load the new U-Boot image and reboot ebony.
-
-4. Repair the SPD eeprom using the 'i2c mm' command. Here's the eeprom
-contents that work with the default SO-DIMM that comes with the
-ebony board (micron 8VDDT164AG-265A1). Note: these are probably
-_not_ the factory settings ... but they work.
-
-=> i2c md 53 0 10 80
-0000: 80 08 07 0c 0a 01 40 00 04 75 75 00 80 08 00 01 ......@..uu.....
-0010: 0e 04 0c 01 02 20 00 a0 75 00 00 50 3c 50 2d 20 ..... ..u..P<P-
-0020: 90 90 50 50 00 00 00 00 00 41 4b 34 32 75 00 00 ..PP.....AK42u..
-0030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 9c ................
-0040: 2c 00 00 00 00 00 00 00 08 38 56 44 44 54 31 36 ,........8VDDT16
-0050: 36 34 41 47 2d 32 36 35 41 31 20 01 00 01 2c 63 64AG-265A1 ...,c
-0060: 22 25 ab 00 00 00 00 00 00 00 00 00 00 00 00 00 "%..............
-0070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
-
-
-PCI DOUBLE-ENUMERATION WOES
-===========================
-
-If you're not using PCI-X cards and are simply using 32-bit and/or
-33 MHz cards via extenders and the like, you may notice that the
-initial pci scan reports various devices twice ... and configuration
-does not succeed (one or more devices are enumerated twice). To correct
-this we replaced the 2K ohm resistor on the IDSEL line(s) with a
-22 ohm resistor and the problem went away. This change hasn't broken
-anything yet -- use at your own risk.
-
-We never tested anything other than 33 MHz/32-bit cards. If you have
-the chance to do this, please let me know how things turn out :-)
-
-
-Regards,
---Scott
-<smcnutt@artesyncp.com>
+++ /dev/null
-#
-# (C) Copyright 2002
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-PLATFORM_CPPFLAGS += -DCONFIG_440=1
-
-ifeq ($(debug),1)
-PLATFORM_CPPFLAGS += -DDEBUG
-endif
-
-ifeq ($(dbcr),1)
-PLATFORM_CPPFLAGS += -DCONFIG_SYS_INIT_DBCR=0x8cff0000
-endif
+++ /dev/null
-/*
- * Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/processor.h>
-#include <spd_sdram.h>
-
-#define BOOT_SMALL_FLASH 32 /* 00100000 */
-#define FLASH_ONBD_N 2 /* 00000010 */
-#define FLASH_SRAM_SEL 1 /* 00000001 */
-
-DECLARE_GLOBAL_DATA_PTR;
-
-long int fixed_sdram(void);
-
-int board_early_init_f(void)
-{
- uint reg;
- unsigned char *fpga_base = (unsigned char *)CONFIG_SYS_FPGA_BASE;
- unsigned char status;
-
- /*--------------------------------------------------------------------
- * Setup the external bus controller/chip selects
- *-------------------------------------------------------------------*/
- mtdcr(EBC0_CFGADDR, EBC0_CFG);
- reg = mfdcr(EBC0_CFGDATA);
- mtdcr(EBC0_CFGDATA, reg | 0x04000000); /* Set ATC */
-
- mtebc(PB1AP, 0x02815480); /* NVRAM/RTC */
- mtebc(PB1CR, 0x48018000); /* BA=0x480 1MB R/W 8-bit */
- mtebc(PB7AP, 0x01015280); /* FPGA registers */
- mtebc(PB7CR, 0x48318000); /* BA=0x483 1MB R/W 8-bit */
-
- /* read FPGA_REG0 and set the bus controller */
- status = *fpga_base;
- if ((status & BOOT_SMALL_FLASH) && !(status & FLASH_ONBD_N)) {
- mtebc(PB0AP, 0x9b015480); /* FLASH/SRAM */
- mtebc(PB0CR, 0xfff18000); /* BAS=0xfff 1MB R/W 8-bit */
- mtebc(PB2AP, 0x9b015480); /* 4MB FLASH */
- mtebc(PB2CR, 0xff858000); /* BAS=0xff8 4MB R/W 8-bit */
- } else {
- mtebc(PB0AP, 0x9b015480); /* 4MB FLASH */
- mtebc(PB0CR, 0xffc58000); /* BAS=0xffc 4MB R/W 8-bit */
-
- /* set CS2 if FLASH_ONBD_N == 0 */
- if (!(status & FLASH_ONBD_N)) {
- mtebc(PB2AP, 0x9b015480); /* FLASH/SRAM */
- mtebc(PB2CR, 0xff818000); /* BAS=0xff8 4MB R/W 8-bit */
- }
- }
-
- /*--------------------------------------------------------------------
- * Setup the interrupt controller polarities, triggers, etc.
- *-------------------------------------------------------------------*/
- mtdcr(UIC0SR, 0xffffffff); /* clear all */
- mtdcr(UIC0ER, 0x00000000); /* disable all */
- mtdcr(UIC0CR, 0x00000009); /* SMI & UIC1 crit are critical */
- mtdcr(UIC0PR, 0xfffffe13); /* per ref-board manual */
- mtdcr(UIC0TR, 0x01c00008); /* per ref-board manual */
- mtdcr(UIC0VR, 0x00000001); /* int31 highest, base=0x000 */
- mtdcr(UIC0SR, 0xffffffff); /* clear all */
-
- mtdcr(UIC1SR, 0xffffffff); /* clear all */
- mtdcr(UIC1ER, 0x00000000); /* disable all */
- mtdcr(UIC1CR, 0x00000000); /* all non-critical */
- mtdcr(UIC1PR, 0xffffe0ff); /* per ref-board manual */
- mtdcr(UIC1TR, 0x00ffc000); /* per ref-board manual */
- mtdcr(UIC1VR, 0x00000001); /* int31 highest, base=0x000 */
- mtdcr(UIC1SR, 0xffffffff); /* clear all */
-
- return 0;
-}
-
-int checkboard(void)
-{
- char buf[64];
- int i = getenv_f("serial#", buf, sizeof(buf));
-
- printf("Board: Ebony - AMCC PPC440GP Evaluation Board");
- if (i > 0) {
- puts(", serial# ");
- puts(buf);
- }
- putc('\n');
-
- return (0);
-}
-
-phys_size_t initdram(int board_type)
-{
- long dram_size = 0;
-
-#if defined(CONFIG_SPD_EEPROM)
- dram_size = spd_sdram();
-#else
- dram_size = fixed_sdram();
-#endif
- return dram_size;
-}
-
-#if !defined(CONFIG_SPD_EEPROM)
-/*************************************************************************
- * fixed sdram init -- doesn't use serial presence detect.
- *
- * Assumes: 128 MB, non-ECC, non-registered
- * PLB @ 133 MHz
- *
- ************************************************************************/
-long int fixed_sdram(void)
-{
- uint reg;
-
- /*--------------------------------------------------------------------
- * Setup some default
- *------------------------------------------------------------------*/
- mtsdram(SDRAM0_UABBA, 0x00000000); /* ubba=0 (default) */
- mtsdram(SDRAM0_SLIO, 0x00000000); /* rdre=0 wrre=0 rarw=0 */
- mtsdram(SDRAM0_DEVOPT, 0x00000000); /* dll=0 ds=0 (normal) */
- mtsdram(SDRAM0_WDDCTR, 0x00000000); /* wrcp=0 dcd=0 */
- mtsdram(SDRAM0_CLKTR, 0x40000000); /* clkp=1 (90 deg wr) dcdt=0 */
-
- /*--------------------------------------------------------------------
- * Setup for board-specific specific mem
- *------------------------------------------------------------------*/
- /*
- * Following for CAS Latency = 2.5 @ 133 MHz PLB
- */
- mtsdram(SDRAM0_B0CR, 0x000a4001); /* SDBA=0x000 128MB, Mode 3, enabled */
- mtsdram(SDRAM0_TR0, 0x410a4012); /* WR=2 WD=1 CL=2.5 PA=3 CP=4 LD=2 */
- /* RA=10 RD=3 */
- mtsdram(SDRAM0_TR1, 0x8080082f); /* SS=T2 SL=STAGE 3 CD=1 CT=0x02f */
- mtsdram(SDRAM0_RTR, 0x08200000); /* Rate 15.625 ns @ 133 MHz PLB */
- mtsdram(SDRAM0_CFG1, 0x00000000); /* Self-refresh exit, disable PM */
- udelay(400); /* Delay 200 usecs (min) */
-
- /*--------------------------------------------------------------------
- * Enable the controller, then wait for DCEN to complete
- *------------------------------------------------------------------*/
- mtsdram(SDRAM0_CFG0, 0x86000000); /* DCEN=1, PMUD=1, 64-bit */
- for (;;) {
- mfsdram(SDRAM0_MCSTS, reg);
- if (reg & 0x80000000)
- break;
- }
-
- return (128 * 1024 * 1024); /* 128 MB */
-}
-#endif /* !defined(CONFIG_SPD_EEPROM) */
+++ /dev/null
-/*
- * (C) Copyright 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2002 Jun Gu <jung@artesyncp.com>
- * Add support for Am29F016D and dynamic switch setting.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * Modified 4/5/2001
- * Wait for completion of each sector erase command issued
- * 4/5/2001
- * Chris Hallinan - DS4.COM, Inc. - clh@net1plus.com
- */
-
-#include <common.h>
-#include <asm/ppc4xx.h>
-#include <asm/processor.h>
-#include <asm/io.h>
-
-#undef DEBUG
-#ifdef DEBUG
-#define DEBUGF(x...) printf(x)
-#else
-#define DEBUGF(x...)
-#endif /* DEBUG */
-
-#define BOOT_SMALL_FLASH 32 /* 00100000 */
-#define FLASH_ONBD_N 2 /* 00000010 */
-#define FLASH_SRAM_SEL 1 /* 00000001 */
-
-#define BOOT_SMALL_FLASH_VAL 4
-#define FLASH_ONBD_N_VAL 2
-#define FLASH_SRAM_SEL_VAL 1
-
-static unsigned long flash_addr_table[8][CONFIG_SYS_MAX_FLASH_BANKS] = {
- {0xffc00000, 0xffe00000, 0xff880000}, /* 0:000: configuraton 3 */
- {0xffc00000, 0xffe00000, 0xff800000}, /* 1:001: configuraton 4 */
- {0xffc00000, 0xffe00000, 0x00000000}, /* 2:010: configuraton 7 */
- {0xffc00000, 0xffe00000, 0x00000000}, /* 3:011: configuraton 8 */
- {0xff800000, 0xffa00000, 0xfff80000}, /* 4:100: configuraton 1 */
- {0xff800000, 0xffa00000, 0xfff00000}, /* 5:101: configuraton 2 */
- {0xffc00000, 0xffe00000, 0x00000000}, /* 6:110: configuraton 5 */
- {0xffc00000, 0xffe00000, 0x00000000} /* 7:111: configuraton 6 */
-};
-
-/*
- * include common flash code (for amcc boards)
- */
-#include "../common/flash.c"
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size(vu_long * addr, flash_info_t * info);
-
-/*
- * Override the weak default mapping function with a board specific one
- */
-u32 flash_get_bank_size(int cs, int idx)
-{
- u8 reg = in_8((void *)CONFIG_SYS_FPGA_BASE);
-
- if ((reg & BOOT_SMALL_FLASH) && !(reg & FLASH_ONBD_N)) {
- /*
- * cs0: small flash (512KiB)
- * cs2: 2 * big flash (2 * 2MiB)
- */
- if (cs == 0)
- return flash_info[2].size;
- if (cs == 2)
- return flash_info[0].size + flash_info[1].size;
- } else {
- /*
- * cs0: 2 * big flash (2 * 2MiB)
- * cs2: small flash (512KiB)
- */
- if (cs == 0)
- return flash_info[0].size + flash_info[1].size;
- if (cs == 2)
- return flash_info[2].size;
- }
-
- return 0;
-}
-
-unsigned long flash_init(void)
-{
- unsigned long total_b = 0;
- unsigned long size_b[CONFIG_SYS_MAX_FLASH_BANKS];
- unsigned char *fpga_base = (unsigned char *)CONFIG_SYS_FPGA_BASE;
- unsigned char switch_status;
- unsigned short index = 0;
- int i;
-
- /* read FPGA base register FPGA_REG0 */
- switch_status = *fpga_base;
-
- /* check the bitmap of switch status */
- if (switch_status & BOOT_SMALL_FLASH) {
- index += BOOT_SMALL_FLASH_VAL;
- }
- if (switch_status & FLASH_ONBD_N) {
- index += FLASH_ONBD_N_VAL;
- }
- if (switch_status & FLASH_SRAM_SEL) {
- index += FLASH_SRAM_SEL_VAL;
- }
-
- DEBUGF("\n");
- DEBUGF("FLASH: Index: %d\n", index);
-
- /* Init: no FLASHes known */
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
- flash_info[i].flash_id = FLASH_UNKNOWN;
- flash_info[i].sector_count = -1;
- flash_info[i].size = 0;
-
- /* check whether the address is 0 */
- if (flash_addr_table[index][i] == 0) {
- continue;
- }
-
- /* call flash_get_size() to initialize sector address */
- size_b[i] = flash_get_size((vu_long *)
- flash_addr_table[index][i],
- &flash_info[i]);
- flash_info[i].size = size_b[i];
- if (flash_info[i].flash_id == FLASH_UNKNOWN) {
- printf("## Unknown FLASH on Bank %d - Size = 0x%08lx = %ld MB\n",
- i, size_b[i], size_b[i] << 20);
- flash_info[i].sector_count = -1;
- flash_info[i].size = 0;
- }
-
- /* Monitor protection ON by default */
- (void)flash_protect(FLAG_PROTECT_SET, CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN - 1,
- &flash_info[2]);
-#ifdef CONFIG_ENV_IS_IN_FLASH
- (void)flash_protect(FLAG_PROTECT_SET, CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE - 1,
- &flash_info[2]);
- (void)flash_protect(FLAG_PROTECT_SET, CONFIG_ENV_ADDR_REDUND,
- CONFIG_ENV_ADDR_REDUND + CONFIG_ENV_SECT_SIZE - 1,
- &flash_info[2]);
-#endif
-
- total_b += flash_info[i].size;
- }
-
- return total_b;
-}
+++ /dev/null
-/*
-* Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com>
- * SPDX-License-Identifier: GPL-2.0+
-*/
-
-#include <ppc_asm.tmpl>
-#include <config.h>
-#include <asm/mmu.h>
-#include <asm/ppc4xx.h>
-
-/**************************************************************************
- * TLB TABLE
- *
- * This table is used by the cpu boot code to setup the initial tlb
- * entries. Rather than make broad assumptions in the cpu source tree,
- * this table lets each board set things up however they like.
- *
- * Pointer to the table is returned in r1
- *
- *************************************************************************/
-
- .section .bootpg,"ax"
- .globl tlbtab
-
-tlbtab:
- tlbtab_start
-
- tlbentry(0xf0000000, SZ_256M, 0xf0000000, 1, AC_RWX | SA_IG)
-
- /*
- * TLB entries for SDRAM are not needed on this platform.
- * They are dynamically generated in the SPD DDR(2) detection
- * routine.
- */
-
- tlbentry(CONFIG_SYS_PERIPHERAL_BASE, SZ_256M, 0x40000000, 1, AC_RW | SA_IG)
- tlbentry(CONFIG_SYS_ISRAM_BASE, SZ_4K, 0x80000000, 0, AC_RWX)
- tlbentry(CONFIG_SYS_ISRAM_BASE + 0x1000, SZ_4K, 0x80001000, 0, AC_RWX)
- tlbentry(CONFIG_SYS_PCI_BASE, SZ_256M, 0x00000000, 2, AC_RW | SA_IG)
- tlbentry(CONFIG_SYS_PCI_MEMBASE, SZ_256M, 0x00000000, 3, AC_RW | SA_IG)
- tlbtab_end
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_EBONY=y
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+ebony powerpc ppc4xx - - Stefan Roese <sr@denx.de>
taihu powerpc ppc4xx - - John Otken <jotken@softadvances.com>
lcd4_lwmon5 powerpc ppc4xx b6b5e394 2015-10-02 Stefan Roese <sr@denx.de>
da830evm arm arm926ejs d7e8b2b9 2015-09-12 Nick Thompson <nick.thompson@gefanuc.com>
+++ /dev/null
-/*
- * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/************************************************************************
- * board/config_EBONY.h - configuration for AMCC 440GP Ref (Ebony)
- ***********************************************************************/
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*-----------------------------------------------------------------------
- * High Level Configuration Options
- *----------------------------------------------------------------------*/
-#define CONFIG_EBONY 1 /* Board is ebony */
-#define CONFIG_440GP 1 /* Specifc GP support */
-#define CONFIG_440 1 /* ... PPC440 family */
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
-
-#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
-
-/*
- * Include common defines/options for all AMCC eval boards
- */
-#define CONFIG_HOSTNAME ebony
-#include "amcc-common.h"
-
-/*
- * Define here the location of the environment variables (FLASH or NVRAM).
- * Note: DENX encourages to use redundant environment in FLASH. NVRAM is only
- * supported for backward compatibility.
- */
-#if 1
-#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
-#else
-#define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
-#endif
-
-/*-----------------------------------------------------------------------
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-#define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH */
-#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
-#define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */
-#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */
-
-#define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000)
-#define CONFIG_SYS_FPGA_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x08300000)
-
-/*-----------------------------------------------------------------------
- * Initial RAM & stack pointer (placed in internal SRAM)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Serial Port
- *----------------------------------------------------------------------*/
-#define CONFIG_CONS_INDEX 1 /* Use UART0 */
-#define CONFIG_SYS_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */
-
-/*-----------------------------------------------------------------------
- * NVRAM/RTC
- *
- * NOTE: Upper 8 bytes of NVRAM is where the RTC registers are located.
- * The DS1743 code assumes this condition (i.e. -- it assumes the base
- * address for the RTC registers is:
- *
- * CONFIG_SYS_NVRAM_BASE_ADDR + CONFIG_SYS_NVRAM_SIZE
- *
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_NVRAM_SIZE (0x2000 - 8) /* NVRAM size(8k)- RTC regs */
-#define CONFIG_RTC_DS174x 1 /* DS1743 RTC */
-
-#ifdef CONFIG_ENV_IS_IN_NVRAM
-#define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */
-#define CONFIG_ENV_ADDR \
- (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE)
-#endif /* CONFIG_ENV_IS_IN_NVRAM */
-
-/*-----------------------------------------------------------------------
- * FLASH related
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_MAX_FLASH_BANKS 3 /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 32 /* sectors per device */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-
-#define CONFIG_SYS_FLASH_ADDR0 0x5555
-#define CONFIG_SYS_FLASH_ADDR1 0x2aaa
-#define CONFIG_SYS_FLASH_WORD_SIZE unsigned char
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-#endif /* CONFIG_ENV_IS_IN_FLASH */
-
-/*-----------------------------------------------------------------------
- * DDR SDRAM
- *----------------------------------------------------------------------*/
-#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup */
-#define SPD_EEPROM_ADDRESS {0x53,0x52} /* SPD i2c spd addresses */
-#define CONFIG_PROG_SDRAM_TLB 1 /* setup SDRAM TLB's dynamically*/
-
-/*-----------------------------------------------------------------------
- * I2C
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
-
-#define CONFIG_SYS_I2C_MULTI_EEPROMS
-#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1)
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-
-/*
- * Default environment variables
- */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_AMCC_DEF_ENV \
- CONFIG_AMCC_DEF_ENV_POWERPC \
- CONFIG_AMCC_DEF_ENV_PPC_OLD \
- CONFIG_AMCC_DEF_ENV_NOR_UPD \
- "kernel_addr=ff800000\0" \
- "ramdisk_addr=ff810000\0" \
- ""
-
-#define CONFIG_PHY_ADDR 8 /* PHY address */
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#define CONFIG_PHY1_ADDR 9 /* EMAC1 PHY address */
-
-/*
- * Commands additional to the ones defined in amcc-common.h
- */
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_SNTP
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-/* General PCI */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */
-
-/* Board-specific PCI */
-#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
-
-#endif /* __CONFIG_H */
projects / u-boot / commitdiff