--- /dev/null
+/*
+ * Copyright 2007 Wind River Systems <www.windriver.com>
+ * Copyright 2007 Embedded Specialties, Inc.
+ * Copyright 2004, 2007 Freescale Semiconductor.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * sbc8548 board configuration file
+ *
+ * Please refer to doc/README.sbc85xx for more info.
+ *
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE 1 /* BOOKE */
+#define CONFIG_E500 1 /* BOOKE e500 family */
+#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */
+#define CONFIG_MPC8548 1 /* MPC8548 specific */
+#define CONFIG_SBC8548 1 /* SBC8548 board specific */
+
+#undef CONFIG_PCI /* enable any pci type devices */
+#undef CONFIG_PCI1 /* PCI controller 1 */
+#undef CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */
+#undef CONFIG_RIO
+#undef CONFIG_PCI2
+#undef CONFIG_FSL_PCI_INIT /* Use common FSL init code */
+
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_DLL /* possible DLL fix needed */
+#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
+
+#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
+
+
+#define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */
+
+#define CONFIG_SYS_CLK_FREQ 66000000 /* SBC8548 default SYSCLK */
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
+#define CONFIG_CLEAR_LAW0 /* Clear LAW0 in cpu_init_r */
+
+/*
+ * Only possible on E500 Version 2 or newer cores.
+ */
+#define CONFIG_ENABLE_36BIT_PHYS 1
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
+
+#undef CFG_DRAM_TEST /* memory test, takes time */
+#define CFG_MEMTEST_START 0x00200000 /* memtest works on */
+#define CFG_MEMTEST_END 0x00400000
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+
+#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000)
+#define CFG_PCI2_ADDR (CFG_CCSRBAR+0x9000)
+#define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000)
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
+#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+
+#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
+
+/*
+ * Make sure required options are set
+ */
+#ifndef CONFIG_SPD_EEPROM
+ #define CFG_SDRAM_SIZE 256 /* DDR is 256MB */
+#endif
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+/*
+ * FLASH on the Local Bus
+ * Two banks, one 8MB the other 64MB, using the CFI driver.
+ * Boot from BR0/OR0 bank at 0xff80_0000
+ * Alternate BR6/OR6 bank at 0xfb80_0000
+ *
+ * BR0:
+ * Base address 0 = 0xff80_0000 = BR0[0:16] = 1111 1111 1000 0000 0
+ * Port Size = 8 bits = BRx[19:20] = 01
+ * Use GPCM = BRx[24:26] = 000
+ * Valid = BRx[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 1111 1000 0000 0000 1000 0000 0001 = ff800801 BR0
+ *
+ * BR6:
+ * Base address 6 = 0xfb80_0000 = BR6[0:16] = 1111 1011 1000 0000 0
+ * Port Size = 32 bits = BRx[19:20] = 11
+ * Use GPCM = BRx[24:26] = 000
+ * Valid = BRx[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 1011 1000 0000 0001 1000 0000 0001 = fb801801 BR6
+ *
+ * OR0:
+ * Addr Mask = 8M = OR1[0:16] = 1111 1111 1000 0000 0
+ * XAM = OR0[17:18] = 11
+ * CSNT = OR0[20] = 1
+ * ACS = half cycle delay = OR0[21:22] = 11
+ * SCY = 6 = OR0[24:27] = 0110
+ * TRLX = use relaxed timing = OR0[29] = 1
+ * EAD = use external address latch delay = OR0[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 OR0
+ *
+ * OR6:
+ * Addr Mask = 64M = OR6[0:16] = 1111 1100 0000 0000 0
+ * XAM = OR6[17:18] = 11
+ * CSNT = OR6[20] = 1
+ * ACS = half cycle delay = OR6[21:22] = 11
+ * SCY = 6 = OR6[24:27] = 0110
+ * TRLX = use relaxed timing = OR6[29] = 1
+ * EAD = use external address latch delay = OR6[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 1100 0000 0000 0110 1110 0110 0101 = fc006e65 OR6
+ */
+
+#define CFG_BOOT_BLOCK 0xff800000 /* start of 8MB Flash */
+#define CFG_FLASH_BASE CFG_BOOT_BLOCK /* start of FLASH 16M */
+
+#define CFG_BR0_PRELIM 0xff800801
+#define CFG_BR6_PRELIM 0xfb801801
+
+#define CFG_OR0_PRELIM 0xff806e65
+#define CFG_OR6_PRELIM 0xfc006e65
+
+#define CFG_FLASH_BANKS_LIST {0xff800000, CFG_FLASH_BASE}
+#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
+#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
+#undef CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_FLASH_EMPTY_INFO
+
+/* CS5 = Local bus peripherals controlled by the EPLD */
+
+#define CFG_BR5_PRELIM 0xf8000801
+#define CFG_OR5_PRELIM 0xff006e65
+#define CFG_EPLD_BASE 0xf8000000
+#define CFG_LED_DISP_BASE 0xf8000000
+#define CFG_USER_SWITCHES_BASE 0xf8100000
+#define CFG_BD_REV 0xf8300000
+#define CFG_EEPROM_BASE 0xf8b00000
+
+/*
+ * SDRAM on the Local Bus
+ */
+#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
+#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
+
+/*
+ * Base Register 3 and Option Register 3 configure SDRAM.
+ * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
+ *
+ * For BR3, need:
+ * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
+ * port-size = 32-bits = BR2[19:20] = 11
+ * no parity checking = BR2[21:22] = 00
+ * SDRAM for MSEL = BR2[24:26] = 011
+ * Valid = BR[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
+ *
+ */
+
+#define CFG_BR3_PRELIM 0xf0001861
+
+/*
+ * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
+ *
+ * For OR3, need:
+ * 64MB mask for AM, OR3[0:7] = 1111 1100
+ * XAM, OR3[17:18] = 11
+ * 10 columns OR3[19-21] = 011
+ * 12 rows OR3[23-25] = 011
+ * EAD set for extra time OR[31] = 0
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 1100 0000 0000 0110 1100 1100 0000 = fc006cc0
+ */
+
+#define CFG_OR3_PRELIM 0xfc006cc0
+
+#define CFG_LBC_LCRR 0x00000002 /* LB clock ratio reg */
+#define CFG_LBC_LBCR 0x00000000 /* LB config reg */
+#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
+#define CFG_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/
+
+/*
+ * LSDMR masks
+ */
+#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1))
+#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10))
+#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10))
+#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16))
+#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19))
+#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22))
+#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22))
+#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23))
+#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27))
+#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31))
+
+#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
+
+/*
+ * Common settings for all Local Bus SDRAM commands.
+ * At run time, either BSMA1516 (for CPU 1.1)
+ * or BSMA1617 (for CPU 1.0) (old)
+ * is OR'ed in too.
+ */
+#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_RFCR16 \
+ | CFG_LBC_LSDMR_PRETOACT7 \
+ | CFG_LBC_LSDMR_ACTTORW7 \
+ | CFG_LBC_LSDMR_BL8 \
+ | CFG_LBC_LSDMR_WRC4 \
+ | CFG_LBC_LSDMR_CL3 \
+ | CFG_LBC_LSDMR_RFEN \
+ )
+
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK 1
+#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+
+#define CFG_INIT_L2_ADDR 0xf8f80000 /* relocate boot L2SRAM */
+
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_CLK 400000000 /* get_bus_freq(0) */
+
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_EEPROM_ADDR 0x50
+#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_OFFSET 0x3000
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+#define CFG_PCI_PHYS 0x80000000 /* 1G PCI TLB */
+
+#define CFG_PCI1_MEM_BASE 0x80000000
+#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI1_IO_BASE 0x00000000
+#define CFG_PCI1_IO_PHYS 0xe2000000
+#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
+
+#ifdef CONFIG_PCI2
+#define CFG_PCI2_MEM_BASE 0xa0000000
+#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
+#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI2_IO_BASE 0x00000000
+#define CFG_PCI2_IO_PHYS 0xe2800000
+#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */
+#endif
+
+#ifdef CONFIG_PCIE1
+#define CFG_PCIE1_MEM_BASE 0xa0000000
+#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE
+#define CFG_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCIE1_IO_BASE 0x00000000
+#define CFG_PCIE1_IO_PHYS 0xe3000000
+#define CFG_PCIE1_IO_SIZE 0x00100000 /* 1M */
+#endif
+
+#ifdef CONFIG_RIO
+/*
+ * RapidIO MMU
+ */
+#define CFG_RIO_MEM_BASE 0xC0000000
+#define CFG_RIO_MEM_SIZE 0x20000000 /* 512M */
+#endif
+
+#ifdef CONFIG_LEGACY
+#define BRIDGE_ID 17
+#define VIA_ID 2
+#else
+#define BRIDGE_ID 28
+#define VIA_ID 4
+#endif
+
+#if defined(CONFIG_PCI)
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+
+#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+
+/* PCI view of System Memory */
+#define CFG_PCI_MEMORY_BUS 0x00000000
+#define CFG_PCI_MEMORY_PHYS 0x00000000
+#define CFG_PCI_MEMORY_SIZE 0x80000000
+
+#endif /* CONFIG_PCI */
+
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 1
+#endif
+
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "eTSEC0"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "eTSEC1"
+#define CONFIG_TSEC3 1
+#define CONFIG_TSEC3_NAME "eTSEC2"
+#define CONFIG_TSEC4
+#define CONFIG_TSEC4_NAME "eTSEC3"
+#undef CONFIG_MPC85XX_FEC
+
+#define TSEC1_PHY_ADDR 0
+#define TSEC2_PHY_ADDR 1
+#define TSEC3_PHY_ADDR 2
+#define TSEC4_PHY_ADDR 3
+
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define TSEC3_PHYIDX 0
+#define TSEC4_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
+#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+
+/* Options are: eTSEC[0-3] */
+#define CONFIG_ETHPRIME "eTSEC0"
+#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
+#endif /* CONFIG_TSEC_ENET */
+
+/*
+ * Environment
+ */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
+#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
+#define CFG_ENV_SIZE 0x2000
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
+
+#if defined(CONFIG_PCI)
+ #define CONFIG_CMD_PCI
+#endif
+
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_LOAD_ADDR 0x2000000 /* default load address */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE 32768
+#define CFG_CACHELINE_SIZE 32
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+/* The mac addresses for all ethernet interface */
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#define CONFIG_ETHADDR 02:E0:0C:00:00:FD
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR 02:E0:0C:00:01:FD
+#define CONFIG_HAS_ETH2
+#define CONFIG_ETH2ADDR 02:E0:0C:00:02:FD
+#define CONFIG_HAS_ETH3
+#define CONFIG_ETH3ADDR 02:E0:0C:00:03:FD
+#endif
+
+#define CONFIG_IPADDR 192.168.0.55
+
+#define CONFIG_HOSTNAME sbc8548
+#define CONFIG_ROOTPATH /opt/eldk/ppc_85xx
+#define CONFIG_BOOTFILE /uImage
+#define CONFIG_UBOOTPATH /u-boot.bin /* TFTP server */
+
+#define CONFIG_SERVERIP 192.168.0.2
+#define CONFIG_GATEWAYIP 192.168.0.1
+#define CONFIG_NETMASK 255.255.255.0
+
+#define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/
+
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot; " \
+ "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
+ "erase " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
+ "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=uRamdisk\0" \
+ "fdtaddr=c00000\0" \
+ "fdtfile=sbc8548.dtb\0"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
+
+#endif /* __CONFIG_H */
projects / u-boot / commitdiff