with full function and phisical connectors support like type-C ports,
usb2.0 host ports, LVDS, JTAG, MAC, SDcard, HDMI, USB-2-serial...
+config TARGET_PUMA_RK3399
+ bool "Theobroma Systems RK3399-Q7 (Puma)"
+ help
+ The RK3399-Q7 (Puma) is a system-on-module (designed and
+ marketed by Theobroma Systems) featuring the Rockchip RK3399
+ in a Qseven-compatible form-factor (running of a single 5V
+ supply and exposing its external interfaces on a MXM-230
+ connector).
+
+ Key features of the RK3399-Q7 include:
+ * on-module USB 3.0 hub (2x USB 3.0 host + 1x USB 2.0 host)
+ * USB 3.0 dual-role
+ * on-module Micrel KSZ9031 GbE PHY
+ * on-module eMMC (up to 256GB configurations available)
+ * on-module DDR3 (1GB, 2GB and 4GB configurations available)
+ * HDMI, eDP, MIPI-DSI, MIPI-DSI/CSI and MIPI-CSI
+ * SPI, I2C, I2S, UART, GPIO, ...
+
endchoice
config SYS_SOC
default 0x0800
source "board/rockchip/evb_rk3399/Kconfig"
+source "board/theobroma-systems/puma_rk3399/Kconfig"
endif
--- /dev/null
+if TARGET_PUMA_RK3399
+
+config SYS_BOARD
+ default "puma_rk3399"
+
+config SYS_VENDOR
+ default "theobroma-systems"
+
+config SYS_CONFIG_NAME
+ default "puma_rk3399"
+
+config BOARD_SPECIFIC_OPTIONS # dummy
+ def_bool y
+
+endif
--- /dev/null
+PUMA-RK3399
+M: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
+M: Klaus Goger <klaus.goger@theobroma-systems.com>
+S: Maintained
+F: board/theobroma-systems/puma_rk3399
+F: include/configs/puma_rk3399.h
+F: arch/arm/dts/rk3399-puma.dts
+F: configs/puma-rk3399_defconfig
+W: https://www.theobroma-systems.com/rk3399-q7/tech-specs
+T: git git://git.theobroma-systems.com/puma-u-boot.git
--- /dev/null
+#
+# (C) Copyright 2017 Theobroma Systems Design und Consulting GmbH
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += puma-rk3399.o
--- /dev/null
+Introduction
+============
+
+The RK3399-Q7 (Puma) is a system-on-module featuring the Rockchip
+RK3399 in a Qseven-compatible form-factor.
+
+RK3399-Q7 features:
+ * CPU: ARMv8 64bit Big-Little architecture,
+ * Big: dual-core Cortex-A72
+ * Little: quad-core Cortex-A53
+ * IRAM: 200KB
+ * DRAM: 4GB-128MB dual-channel
+ * eMMC: onboard eMMC
+ * SD/MMC
+ * GbE (onboard Micrel KSZ9031) Gigabit ethernet PHY
+ * USB:
+ * USB3.0 dual role port
+ * 2x USB3.0 host, 1x USB2.0 host via onboard USB3.0 hub
+ * Display: HDMI/eDP/MIPI
+ * Camera: 2x CSI (one on the edge connector, one on the Q7 specified CSI ZIF)
+ * NOR Flash: onboard SPI NOR
+ * Companion Controller: onboard additional Cortex-M0 microcontroller
+ * RTC
+ * fan controller
+ * CAN
+
+Here is the step-by-step to boot to U-Boot on rk3399.
+
+Get the Source and build ATF/Cortex-M0 binaries
+===============================================
+
+ > git clone git://git.theobroma-systems.com/arm-trusted-firmware.git
+ > git clone git://git.theobroma-systems.com/rk3399-cortex-m0.git
+
+Compile the ATF
+===============
+
+ > cd arm-trusted-firmware
+ > make CROSS_COMPILE=aarch64-linux-gnu- PLAT=rk3399 bl31
+ > cp build/rk3399/release/bl31.bin ../u-boot
+
+Compile the M0 firmware
+=======================
+
+ > cd ../rk3399-cortex-m0
+ > make CROSS_COMPILE=arm-cortex_m0-eabi-
+ > cp rk3399m0.bin ../u-boot
+
+Compile the U-Boot
+==================
+
+ > cd ../u-boot
+ > make CROSS_COMPILE=aarch64-linux-gnu- puma-rk3399_defconfig all
+
+Package the image
+=================
+
+ > tools/mkimage -n rk3399 -T rksd -d spl/u-boot-spl.bin spl.img
+ > tools/mkimage -f board/theobroma/puma_rk3399/fit_spl_atf.its \
+ -E rk3399_bl3x.itb
+
+Flash the image
+===============
+
+Copy the SPL to offset 32k and the FIT image containing the payloads
+(U-Boot proper, ATF, M0 Firmware, devicetree) to offset 256k on a SD
+card.
+
+ > dd if=spl.img of=/dev/sdb seek=64
+ > dd if=rk3399_bl3x.itb of=/dev/sdb seek=512
+
+After powering up the board (with the inserted SD card), you should see
+a U-Boot console on UART0 (115200n8).
--- /dev/null
+/*
+ * Copyright (C) 2017 Theobroma Systems Design und Consulting GmbH
+ *
+ * Minimal dts for a SPL FIT image payload.
+ *
+ * SPDX-License-Identifier: GPL-2.0+ X11
+ */
+
+/dts-v1/;
+
+/ {
+ description = "FIT image with U-Boot proper, ATF bl31, M0 Firmware, DTB";
+ #address-cells = <1>;
+
+ images {
+ uboot@1 {
+ description = "U-Boot (64-bit)";
+ data = /incbin/("../../../u-boot-nodtb.bin");
+ type = "standalone";
+ arch = "arm64";
+ compression = "none";
+ load = <0x00200000>;
+ };
+ atf@1 {
+ description = "ARM Trusted Firmware";
+ data = /incbin/("../../../bl31.bin");
+ type = "firmware";
+ arch = "arm64";
+ compression = "none";
+ load = <0x00001000>;
+ entry = <0x00001000>;
+ };
+ pmu@1 {
+ description = "Cortex-M0 firmware";
+ data = /incbin/("../../../rk3399m0.bin");
+ type = "pmu-firmware";
+ compression = "none";
+ load = <0xff8c0000>;
+ };
+ fdt@1 {
+ description = "RK3399-Q7 (Puma) flat device-tree";
+ data = /incbin/("../../../u-boot.dtb");
+ type = "flat_dt";
+ compression = "none";
+ };
+ };
+
+ configurations {
+ default = "conf@1";
+ conf@1 {
+ description = "Theobroma Systems RK3399-Q7 (Puma) SoM";
+ firmware = "uboot@1";
+ loadables = "atf@1";
+ fdt = "fdt@1";
+ };
+ };
+};
--- /dev/null
+/*
+ * (C) Copyright 2017 Theobroma Systems Design und Consulting GmbH
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#include <common.h>
+#include <dm.h>
+#include <dm/pinctrl.h>
+#include <dm/uclass-internal.h>
+#include <asm/arch/periph.h>
+#include <power/regulator.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+ struct udevice *pinctrl, *regulator;
+ int ret;
+
+ /*
+ * The PWM does not have decicated interrupt number in dts and can
+ * not get periph_id by pinctrl framework, so let's init them here.
+ * The PWM2 and PWM3 are for pwm regulators.
+ */
+ ret = uclass_get_device(UCLASS_PINCTRL, 0, &pinctrl);
+ if (ret) {
+ debug("%s: Cannot find pinctrl device\n", __func__);
+ goto out;
+ }
+
+ ret = pinctrl_request_noflags(pinctrl, PERIPH_ID_PWM2);
+ if (ret) {
+ debug("%s PWM2 pinctrl init fail!\n", __func__);
+ goto out;
+ }
+
+ /* rk3399 need to init vdd_center to get the correct output voltage */
+ ret = regulator_get_by_platname("vdd_center", ®ulator);
+ if (ret)
+ debug("%s: Cannot get vdd_center regulator\n", __func__);
+
+ ret = regulator_get_by_platname("vcc5v0_host", ®ulator);
+ if (ret) {
+ debug("%s vcc5v0_host init fail! ret %d\n", __func__, ret);
+ goto out;
+ }
+
+ ret = regulator_set_enable(regulator, true);
+ if (ret) {
+ debug("%s vcc5v0-host-en set fail!\n", __func__);
+ goto out;
+ }
+
+out:
+ return 0;
+}
+
+int dram_init(void)
+{
+ gd->ram_size = 0x80000000;
+ return 0;
+}
+
+int dram_init_banksize(void)
+{
+ /* Reserve 0x200000 for ATF bl31 */
+ gd->bd->bi_dram[0].start = 0x200000;
+ gd->bd->bi_dram[0].size = 0x7e000000;
+
+ return 0;
+}
CONFIG_ARM=y
CONFIG_ARCH_ROCKCHIP=y
+CONFIG_TARGET_PUMA_RK3399=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SYS_MALLOC_F_LEN=0x4000
CONFIG_FIT=y
CONFIG_SPL_FIT=y
CONFIG_SPL_LOAD_FIT=y
-CONFIG_SPL_FIT_SOURCE="board/rockchip/evb_rk3399/fit_spl_atf.its"
+CONFIG_SPL_FIT_SOURCE="board/theobroma-systems/puma_rk3399/fit_spl_atf.its"
# CONFIG_DISPLAY_CPUINFO is not set
# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
# CONFIG_SPL_LEGACY_IMAGE_SUPPORT is not set
--- /dev/null
+/*
+ * (C) Copyright 2017 Theobroma Systems Design und Consulting GmbH
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __PUMA_RK3399_H
+#define __PUMA_RK3399_H
+
+#include <configs/rk3399_common.h>
+
+/*
+ * SPL @ 32kB for ~130kB
+ * ENV @ 240KB for 8kB
+ * FIT payload (ATF, U-Boot, FDT) @ 256kB
+ */
+#undef CONFIG_ENV_OFFSET
+#define CONFIG_ENV_OFFSET (240 * 1024)
+
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 1
+
+#define SDRAM_BANK_SIZE (2UL << 30)
+
+#define CONFIG_SYS_WHITE_ON_BLACK
+
+#endif
projects / u-boot / commitdiff