#define CONFIG_OMAP1510 1 /* which is in a 5910 */
/* Input clock of PLL */
-#define CONFIG_SYS_CLK_FREQ 150000000 /* 150MHz input clock */
-#define CONFIG_XTAL_FREQ 12000000
+#define CONFIG_SYS_CLK_FREQ 150000000 /* 150MHz */
+#define CONFIG_XTAL_FREQ 12000000 /* 12MHz */
#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
/*
* Physical Memory Map
*/
-#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
-#define PHYS_SDRAM_1 0x10000000 /* SDRAM Bank #1 */
-#define PHYS_SDRAM_1_SIZE (64 * 1024 * 1024)
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM_1 0x10000000
+#define PHYS_SDRAM_1_SIZE (64 * 1024 * 1024)
+#define PHYS_FLASH_1 0x0000000
-#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
-
-#define CONFIG_SYS_LOAD_ADDR PHYS_SDRAM_1 + 0x400000 /* default load address */
-
-/*
- * FLASH organization
- */
-#define CONFIG_SYS_FLASH_CFI /* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER /* Use the common driver */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
-#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
-
-/* FIXME: Does not work on AMD flash */
-/* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 */ /* use buffered writes (20x faster) */
-#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max # of sectors on one chip */
-
-#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1
+#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1
#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
/*
* Environment settings
*/
#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_ENV_SIZE (8 * 1024)
-#define CONFIG_ENV_SECT_SIZE (64 * 1024)
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
+#define CONFIG_ENV_ADDR (PHYS_FLASH_1 + CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SIZE (8 * 1024)
+#define CONFIG_ENV_SECT_SIZE (64 * 1024)
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
#define CONFIG_ENV_OVERWRITE
/*
* Size of malloc() pool and stack
*/
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE 128
#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
-#define CONFIG_STACKSIZE (1 * 1024 * 1024)
-#define PHYS_SDRAM_1_RESERVED (CONFIG_SYS_MONITOR_LEN + CONFIG_SYS_MALLOC_LEN + CONFIG_STACKSIZE)
+#define CONFIG_STACKSIZE (1 * 1024 * 1024)
/*
* Hardware drivers
*/
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK (CONFIG_XTAL_FREQ)
+#define CONFIG_SYS_NS16550_COM1 OMAP1510_UART1_BASE
+
#define CONFIG_NET_MULTI
#define CONFIG_SMC91111
-#define CONFIG_SMC91111_BASE 0x08000300
+#define CONFIG_SMC91111_BASE 0x08000300
+
+#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_MAX_FLASH_SECT 512
+
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#define CONFIG_HARD_I2C
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_DRIVER_OMAP1510_I2C
#define CONFIG_RTC_DS1307
-#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK (CONFIG_XTAL_FREQ) /* can be 12M/32Khz or 48Mhz */
-#define CONFIG_SYS_NS16550_COM1 OMAP1510_UART1_BASE /* uart1 */
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*
- * Command line configuration.
+ * Command line configuration
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_PING
#define CONFIG_CMD_RUN
-
/*
* BOOTP options
*/
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTPATH
-
#define CONFIG_LOOPW
#define CONFIG_BOOTDELAY 3
#define CONFIG_ZERO_BOOTDELAY_CHECK /* allow to break in always */
-#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/
-#define CONFIG_SYS_AUTOLOAD "n" /* No autoload */
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/
+#define CONFIG_SYS_AUTOLOAD "n"
#define CONFIG_BOOTCOMMAND "run nboot"
#define CONFIG_PREBOOT "run setup"
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "silent=1\0" \
- "ospart=0\0" \
- "bootfile=/boot/uImage\0" \
- "setpart=" \
- "if test -n $swapos; then " \
- "setenv swapos; saveenv; " \
- "if test $ospart -eq 0; then setenv ospart 1; else setenv ospart 0; fi; "\
- "fi\0" \
- "setup=setenv bootargs console=ttyS0,$baudrate " \
- "mtdparts=$mtdparts\0" \
- "nfsargs=setenv bootargs $bootargs " \
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "silent=1\0" \
+ "ospart=0\0" \
+ "bootfile=/boot/uImage\0" \
+ "setpart=" \
+ "if test -n $swapos; then " \
+ "setenv swapos; saveenv; " \
+ "if test $ospart -eq 0; then " \
+ "setenv ospart 1; " \
+ "else " \
+ "setenv ospart 0; " \
+ "fi; " \
+ "fi\0" \
+ "setup=setenv bootargs console=ttyS0,$baudrate " \
+ "mtdparts=$mtdparts\0" \
+ "nfsargs=setenv bootargs $bootargs " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off " \
- "nfsroot=$rootpath root=/dev/nfs\0" \
- "flashargs=run setpart; setenv bootargs $bootargs " \
- "root=mtd:data$ospart ro " \
- "rootfstype=jffs2\0" \
- "initrdargs=setenv bootargs $bootargs " \
+ "nfsroot=$rootpath root=/dev/nfs\0" \
+ "flashargs=run setpart; setenv bootargs $bootargs " \
+ "root=mtd:data$ospart ro " \
+ "rootfstype=jffs2\0" \
+ "initrdargs=setenv bootargs $bootargs " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off\0" \
- "fboot=run flashargs; chpart data$ospart; fsload; bootm\0" \
- "mboot=bootp; run initrdargs; tftp; bootm\0" \
+ "fboot=run flashargs; chpart data$ospart; fsload; bootm\0" \
+ "mboot=bootp; run initrdargs; tftp; bootm\0" \
"nboot=bootp; run nfsargs; tftp; bootm\0"
#define CONFIG_SILENT_CONSOLE 1 /* enable silent startup */
#endif
/*
- * JFFS2 partitions (mtdparts command line support)
+ * Partitions (mtdparts command line support)
*/
#define CONFIG_CMD_MTDPARTS
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
#define CONFIG_FLASH_CFI_MTD
-#define MTDIDS_DEFAULT "nor0=omapflash.0"
-#define MTDPARTS_DEFAULT "mtdparts=omapflash.0:256k(u-boot),64k(env),64k(r_env),16192k(data0),-(data1)"
-
+#define MTDIDS_DEFAULT "nor0=physmap-flash.0"
+#define MTDPARTS_DEFAULT "mtdparts=physmap-flash.0:" \
+ "256k(u-boot),64k(env),64k(r_env),16192k(data0),-(data1)"
/*
* Miscellaneous configurable options
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "# " /* Monitor Command Prompt */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1
-#define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE - PHYS_SDRAM_1_RESERVED
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_PROMPT "# "
+#define CONFIG_SYS_CBSIZE 256
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
+ sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1)
+#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE - \
+ (CONFIG_SYS_MONITOR_LEN + CONFIG_SYS_MALLOC_LEN + CONFIG_STACKSIZE))
+#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x400000)
-/* The 1510 has 3 timers, they can be driven by the RefClk (12MHz) or by DPLL1.
+/*
+ * The 1510 has 3 timers, they can be driven by the RefClk (12MHz) or by DPLL1.
* This time is further subdivided by a local divisor.
*/
-#define CONFIG_SYS_TIMERBASE OMAP1510_TIMER1_BASE
-#define CONFIG_SYS_PTV 7 /* 2^(PTV+1), divide by 256 */
-#define CONFIG_SYS_HZ 1000
+#define CONFIG_SYS_TIMERBASE OMAP1510_TIMER1_BASE
+#define CONFIG_SYS_PTV 7 /* 2^(PTV+1), divide by 256 */
+#define CONFIG_SYS_HZ 1000
-#define OMAP5910_DPLL_DIV 1
-#define OMAP5910_DPLL_MUL ((CONFIG_SYS_CLK_FREQ * \
- (1 << OMAP5910_DPLL_DIV)) / CONFIG_XTAL_FREQ)
+#define OMAP5910_DPLL_DIV 1
+#define OMAP5910_DPLL_MUL \
+ ((CONFIG_SYS_CLK_FREQ * (1 << OMAP5910_DPLL_DIV)) / CONFIG_XTAL_FREQ)
#define OMAP5910_ARM_PER_DIV 2 /* CKL/4 */
#define OMAP5910_LCD_DIV 2 /* CKL/4 */
projects / u-boot / commitdiff