/*
+ * (C) Copyright 2006 Detlev Zundel, dzu@denx.de
* (C) Copyright 2001
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
int checkboard (void)
{
- puts ("Board: NC650\n");
+#if !defined(CONFIG_CP850)
+ puts ("Board: NC650");
+#else
+ puts ("Board: CP850");
+#endif
+#if defined(CONFIG_IDS852_REV1)
+ puts (" with IDS852 rev 1 module\n");
+#elif defined(CONFIG_IDS852_REV2)
+ puts (" with IDS852 rev 2 module\n");
+#endif
return 0;
}
return (get_ram_size(base, maxsize));
}
-#if (CONFIG_COMMANDS & CFG_CMD_NAND)
-void nand_init(void)
-{
- extern unsigned long nand_probe(unsigned long physadr);
- unsigned long totlen = nand_probe(CFG_NAND_BASE);
+#if defined(CONFIG_CP850)
+
+#define DPRAM_VARNAME "KP850DIP"
+#define PARAM_ADDR 0x7C0
+#define NAME_ADDR 0x7F8
+#define BOARD_NAME "KP01"
+#define DEFAULT_LB "241111"
- printf ("%4lu MB\n", totlen >> 20);
+int misc_init_r(void)
+{
+ int iCompatMode = 0;
+ char *pParam = NULL;
+ char *envlb;
+
+ /*
+ First byte in CPLD read address space signals compatibility mode
+ 0 - cp850
+ 1 - kp852
+ */
+ pParam = (char*)(CFG_CPLD_BASE);
+ if( *pParam != 0)
+ iCompatMode = 1;
+
+ if ( iCompatMode != 0) {
+ /*
+ In KP852 compatibility mode we have to write to
+ DPRAM as early as possible the binary coded
+ line config and board name.
+ The line config is derived from the environment
+ variable DPRAM_VARNAME by converting from ASCII
+ to binary per character.
+ */
+ if ( (envlb = getenv ( DPRAM_VARNAME )) == 0) {
+ setenv( DPRAM_VARNAME, DEFAULT_LB);
+ envlb = DEFAULT_LB;
+ }
+
+ /* Status string */
+ printf("Mode: KP852(LB=%s)\n", envlb);
+
+ /* copy appl init */
+ pParam = (char*)(DPRAM_BASE_ADDR + PARAM_ADDR);
+ while (*envlb) {
+ *(pParam++) = *(envlb++) - '0';
+ }
+ *pParam = '\0';
+
+ /* copy board id */
+ pParam = (char*)(DPRAM_BASE_ADDR + NAME_ADDR);
+ strcpy( pParam, BOARD_NAME);
+ } else {
+ puts("Mode: CP850\n");
+ }
+
+ return 0;
}
#endif
/*
+ * (C) Copyright 2006 Detlev Zundel, dzu@denx.de
* (C) Copyright 2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
#define CFG_8XX_XIN CONFIG_8xx_OSCLK
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#define CONFIG_AUTOBOOT_KEYED
+#define CONFIG_AUTOBOOT_PROMPT "\nEnter password - autoboot in %d seconds...\n"
+#define CONFIG_AUTOBOOT_DELAY_STR "ids"
+#define CONFIG_BOOT_RETRY_TIME 900
+#define CONFIG_BOOT_RETRY_MIN 30
#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
"bootm"
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#define CONFIG_WATCHDOG /* watchdog enabled */
#undef CONFIG_STATUS_LED /* Status LED disabled */
/*
* Software (bit-bang) I2C driver configuration
*/
+#if defined(CONFIG_IDS852_REV1)
+
#define SCL 0x1000 /* PA 3 */
#define SDA 0x2000 /* PA 2 */
#define __I2C_DIR immr->im_ioport.iop_padir
#define __I2C_DAT immr->im_ioport.iop_padat
#define __I2C_PAR immr->im_ioport.iop_papar
+
+#elif defined(CONFIG_IDS852_REV2)
+
+#define SCL 0x0002 /* PB 30 */
+#define SDA 0x0001 /* PB 31 */
+
+#define __I2C_PAR immr->im_cpm.cp_pbpar
+#define __I2C_DIR immr->im_cpm.cp_pbdir
+#define __I2C_DAT immr->im_cpm.cp_pbdat
+
+#endif
+
#define I2C_INIT { __I2C_PAR &= ~(SDA|SCL); \
__I2C_DIR |= (SDA|SCL); }
#define I2C_READ ((__I2C_DAT & SDA) ? 1 : 0)
#define ADDR_COLUMN 1
#define NAND_NO_RB
-#define NAND_WAIT_READY(nand) udelay(12)
-#define WRITE_NAND_COMMAND(d, adr) WRITE_NAND(d, adr + 2)
-#define WRITE_NAND_ADDRESS(d, adr) WRITE_NAND(d, adr + 1)
-#define WRITE_NAND(d, adr) (*(volatile uint8_t *)(adr) = (uint8_t)(d))
-#define READ_NAND(adr) (*(volatile uint8_t *)(adr))
-#define NAND_DISABLE_CE(nand) /* nop */
-#define NAND_ENABLE_CE(nand) /* nop */
-#define NAND_CTL_CLRALE(nandptr) /* nop */
-#define NAND_CTL_SETALE(nandptr) /* nop */
-#define NAND_CTL_CLRCLE(nandptr) /* nop */
-#define NAND_CTL_SETCLE(nandptr) /* nop */
/*-----------------------------------------------------------------------
* SYPCR - System Protection Control 11-9
#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V)
/*
- * BR2 and OR2 (NAND Flash) - now addressed through UPMB
+ * BR2 and OR2 (NAND Flash) - addressed through UPMB on rev 1
+ * rev2 only uses the chipselect
*/
#define CFG_NAND_BASE 0x50000000
#define CFG_NAND_SIZE 0x04000000
#define CFG_OR3_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM)
#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V)
+/*
+ * BR4 and OR4 (CPLD)
+ */
+#define CFG_CPLD_BASE 0x80000000 /* CPLD */
+#define CFG_CPLD_SIZE 0x10000 /* only 16 used */
+
+#define CFG_OR_TIMING_CPLD (OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \
+ OR_SCY_1_CLK)
+
+#define CFG_BR4_PRELIM ((CFG_CPLD_BASE & BR_BA_MSK) | BR_PS_8 | BR_V )
+#define CFG_OR4_PRELIM (((-CFG_CPLD_SIZE) & OR_AM_MSK) | CFG_OR_TIMING_CPLD)
+
/*
* BR5 and OR5 (SRAM)
*/
#define CFG_BR5_PRELIM ((CFG_SRAM_BASE & BR_BA_MSK) | BR_PS_8 | BR_V )
#define CFG_OR5_PRELIM (((-CFG_SRAM_SIZE) & OR_AM_MSK) | CFG_OR_TIMING_SRAM)
+#if defined(CONFIG_CP850)
+/*
+ * BR6 and OR6 (DPRAM) - only on CP850
+ */
+#define CFG_OR6_PRELIM 0xffff8170
+#define CFG_BR6_PRELIM 0xa0000401
+#define DPRAM_BASE_ADDR 0xa0000000
+
+#define CONFIG_MISC_INIT_R 1
+#endif
/*
* 4096 Rows from SDRAM example configuration
#define CONFIG_JFFS2_PART_OFFSET 0x00000000
/* mtdparts command line support */
-/*
#define CONFIG_JFFS2_CMDLINE
#define MTDIDS_DEFAULT "nor0=nc650-0,nand0=nc650-nand"
#define MTDPARTS_DEFAULT "mtdparts=nc650-0:1m(kernel1),1m(kernel2)," \
- "2560k(cramfs1),2560k(cramfs2)," \
- "256k(u-boot),256k(env);" \
- "nc650-nand:4m(nand1),28m(nand2)"
-*/
+ "4m(cramfs1),1m(cramfs2)," \
+ "256k(u-boot),128k(env);" \
+ "nc650-nand:4m(jffs1),28m(jffs2)"
#endif /* __CONFIG_H */
projects / u-boot / commitdiff