config TARGET_WARP
bool "WaRP"
+config TARGET_XPRESS
+ bool "CCV xPress"
+ select MX6UL
+ select DM
+ select DM_THERMAL
+ select SUPPORT_SPL
+
endchoice
config SYS_SOC
source "board/barco/platinum/Kconfig"
source "board/barco/titanium/Kconfig"
source "board/boundary/nitrogen6x/Kconfig"
+source "board/ccv/xpress/Kconfig"
source "board/compulab/cm_fx6/Kconfig"
source "board/congatec/cgtqmx6eval/Kconfig"
source "board/embest/mx6boards/Kconfig"
--- /dev/null
+if TARGET_XPRESS
+
+config SYS_BOARD
+ default "xpress"
+
+config SYS_VENDOR
+ default "ccv"
+
+config SYS_CONFIG_NAME
+ default "xpress"
+
+endif
--- /dev/null
+CCV XPRESS BOARD
+M: Stefan Roese <sr@denx.de>
+S: Maintained
+F: board/ccv/xpress/
+F: include/configs/xpress.h
+F: configs/xpress_defconfig
+F: configs/xpress_spl_defconfig
--- /dev/null
+#
+# Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := xpress.o
+obj-$(CONFIG_SPL_BUILD) += spl.o
--- /dev/null
+/*
+ * Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+/* image version */
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * sd, nand
+ */
+BOOT_FROM sd
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type Address Value
+ *
+ * where:
+ * Addr-type register length (1,2 or 4 bytes)
+ * Address absolute address of the register
+ * value value to be stored in the register
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* Enable all clocks */
+DATA 4 0x020c4068 0xffffffff
+DATA 4 0x020c406c 0xffffffff
+DATA 4 0x020c4070 0xffffffff
+DATA 4 0x020c4074 0xffffffff
+DATA 4 0x020c4078 0xffffffff
+DATA 4 0x020c407c 0xffffffff
+DATA 4 0x020c4080 0xffffffff
+DATA 4 0x020c4084 0xffffffff
+
+/* ddr io type */
+DATA 4 0x020e04b4 0x000C0000 /* IOMUXC_SW_PAD_CTL_GRP_DDR_TYPE */
+DATA 4 0x020e04ac 0x00000000 /* IOMUXC_SW_PAD_CTL_GRP_DDRPKE */
+
+/* clock */
+DATA 4 0x020e027c 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCLK0_P */
+
+/* control and address */
+DATA 4 0x020E0250 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_CAS */
+DATA 4 0x020E024C 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_RAS */
+DATA 4 0x020E0490 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_ADDDS */
+DATA 4 0x020E0288 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_RESET */
+DATA 4 0x020E0270 0x00000000 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDBA2 - DSE can be
+ configured using Group Control Register:
+ IOMUXC_SW_PAD_CTL_GRP_CTLDS */
+DATA 4 0x020E0260 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_ODT0 */
+DATA 4 0x020E0264 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_ODT1 */
+DATA 4 0x020E04A0 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_CTLDS */
+
+/* data strobes */
+DATA 4 0x020e0494 0x00020000 /* IOMUXC_SW_PAD_CTL_GRP_DDRMODE_CTL */
+DATA 4 0x020e0280 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS0_P */
+DATA 4 0x020e0284 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS1_P */
+
+/* data */
+DATA 4 0x020E04B0 0x00020000 /* IOMUXC_SW_PAD_CTL_GRP_DDRMODE */
+DATA 4 0x020E0498 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_B0DS */
+DATA 4 0x020E04A4 0x00000030 /* IOMUXC_SW_PAD_CTL_GRP_B1DS */
+DATA 4 0x020E0244 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM0 */
+DATA 4 0x020E0248 0x00000030 /* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM1 */
+
+/*
+ * DDR Controller Registers
+ *
+ * Manufacturer: IM
+ * Device Part Number: IME1G16D3EEBG-15EI
+ * Clock Freq.: 400MHz
+ * Density per CS in Gb: 1
+ * Chip Selects used: 1
+ * Number of Banks: 8
+ * Row address: 13
+ * Column address: 10
+ * Data bus width 16
+ */
+DATA 4 0x021b001c 0x00008000 /* MMDC0_MDSCR, set the Configuration request bit
+ during MMDC set up */
+
+/*
+ * Calibration setup
+ */
+DATA 4 0x021b0800 0xA1390003 /* DDR_PHY_P0_MPZQHWCTRL, enable both one-time &
+ periodic HW ZQ calibration. */
+
+/*
+ * For target board, may need to run write leveling calibration to fine tune
+ * these settings.
+ */
+DATA 4 0x021b080c 0x00000000
+
+/* Read DQS Gating calibration */
+DATA 4 0x021b083c 0x4164015C /* MPDGCTRL0 PHY0 */
+
+/* Read calibration */
+DATA 4 0x021b0848 0x40404446 /* MPRDDLCTL PHY0 */
+
+/* Write calibration */
+DATA 4 0x021b0850 0x40405A52 /* MPWRDLCTL PHY0 */
+
+/*
+ * read data bit delay: (3 is the reccommended default value, although out of
+ * reset value is 0)
+ */
+DATA 4 0x021b081c 0x33333333 /* DDR_PHY_P0_MPREDQBY0DL3 */
+DATA 4 0x021b0820 0x33333333 /* DDR_PHY_P0_MPREDQBY1DL3 */
+DATA 4 0x021b082c 0xF3333333
+DATA 4 0x021b0830 0xF3333333
+
+DATA 4 0x021b08c0 0x00921012
+
+/* Clock Fine Tuning */
+DATA 4 0x021B0858 0x00000F00 /* [MMDC_MPSDCTRL] MMDC PHY CK Control Register */
+
+/* Complete calibration by forced measurement: */
+DATA 4 0x021b08b8 0x00000800 /* DDR_PHY_P0_MPMUR0, frc_msr */
+/*
+ * Calibration setup end
+ */
+
+/* MMDC init: */
+DATA 4 0x021b0004 0x0002002D /* MMDC0_MDPDC */
+DATA 4 0x021b0008 0x1B333030 /* MMDC0_MDOTC */
+DATA 4 0x021b000c 0x3F4352F3 /* MMDC0_MDCFG0 */
+DATA 4 0x021b0010 0xB66D0B63 /* MMDC0_MDCFG1 */
+DATA 4 0x021b0014 0x01FF00DB /* MMDC0_MDCFG2 */
+
+/*
+ * MDMISC: RALAT kept to the high level of 5.
+ * MDMISC: consider reducing RALAT if your 528MHz board design allow that.
+ * Lower RALAT benefits:
+ * a. better operation at low frequency, for LPDDR2 freq < 100MHz, change RALAT
+ * to 3
+ * b. Small performence improvment
+ */
+DATA 4 0x021b0018 0x00201740 /* MMDC0_MDMISC */
+
+DATA 4 0x021b001c 0x00008000 /* MMDC0_MDSCR, set the Configuration request bit
+ during MMDC set up */
+
+DATA 4 0x021b002c 0x000026D2 /* MMDC0_MDRWD */
+DATA 4 0x021b0030 0x00431023 /* MMDC0_MDOR */
+DATA 4 0x021b0040 0x00000047 /* Chan0 CS0_END */
+DATA 4 0x021b0000 0x82180000 /* MMDC0_MDCTL */
+
+/* Mode register writes */
+DATA 4 0x021b001c 0x02008032 /* MMDC0_MDSCR, MR2 write, CS0 */
+DATA 4 0x021b001c 0x00008033 /* MMDC0_MDSCR, MR3 write, CS0 */
+DATA 4 0x021b001c 0x00048031 /* MMDC0_MDSCR, MR1 write, CS0 */
+DATA 4 0x021b001c 0x15208030 /* MMDC0_MDSCR, MR0 write, CS0 */
+DATA 4 0x021b001c 0x04008040 /* MMDC0_MDSCR, ZQ calibration command sent to
+ device on CS0 */
+
+DATA 4 0x021b0020 0x00000800 /* MMDC0_MDREF */
+DATA 4 0x021b0818 0x00000227 /* DDR_PHY_P0_MPODTCTRL */
+DATA 4 0x021b0004 0x0002556D /* MMDC0_MDPDC now SDCTL power down enabled */
+DATA 4 0x021b0404 0x00011006 /* MMDC0_MAPSR ADOPT power down enabled, MMDC will
+ enter automatically to self-refresh while the
+ number of idle cycle reached. */
+DATA 4 0x021b001c 0x00000000 /* MMDC0_MDSCR, clear this register (especially
+ the configuration bit as initialization is
+ complete) */
--- /dev/null
+/*
+ * SPL specific code for CCV xPress
+ *
+ * Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <asm/io.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/crm_regs.h>
+
+/* Configuration for IM IME1G16D3EEBG-15EI, 64M x 16 -> 128MiB */
+
+static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
+ .grp_addds = 0x00000030,
+ .grp_ddrmode_ctl = 0x00020000,
+ .grp_b0ds = 0x00000030,
+ .grp_ctlds = 0x00000030,
+ .grp_b1ds = 0x00000030,
+ .grp_ddrpke = 0x00000000,
+ .grp_ddrmode = 0x00020000,
+ .grp_ddr_type = 0x000c0000,
+};
+
+static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
+ .dram_dqm0 = 0x00000030,
+ .dram_dqm1 = 0x00000030,
+ .dram_ras = 0x00000030,
+ .dram_cas = 0x00000030,
+ .dram_odt0 = 0x00000030,
+ .dram_odt1 = 0x00000030,
+ .dram_sdba2 = 0x00000000,
+ .dram_sdclk_0 = 0x00000008,
+ .dram_sdqs0 = 0x00000038,
+ .dram_sdqs1 = 0x00000030,
+ .dram_reset = 0x00000030,
+};
+
+static struct mx6_mmdc_calibration mx6_mmcd_calib = {
+ .p0_mpwldectrl0 = 0x00000000,
+ .p0_mpdgctrl0 = 0x4164015C,
+ .p0_mprddlctl = 0x40404446,
+ .p0_mpwrdlctl = 0x40405A52,
+};
+
+struct mx6_ddr_sysinfo ddr_sysinfo = {
+ .dsize = 0,
+ .cs_density = 20,
+ .ncs = 1,
+ .cs1_mirror = 0,
+ .rtt_wr = 2,
+ .rtt_nom = 1, /* RTT_Nom = RZQ/2 */
+ .walat = 1, /* Write additional latency */
+ .ralat = 5, /* Read additional latency */
+ .mif3_mode = 3, /* Command prediction working mode */
+ .bi_on = 1, /* Bank interleaving enabled */
+ .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
+ .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
+ .ddr_type = DDR_TYPE_DDR3,
+};
+
+static struct mx6_ddr3_cfg mem_ddr = {
+ .mem_speed = 800,
+ .density = 4,
+ .width = 16,
+ .banks = 8,
+ .rowaddr = 13,
+ .coladdr = 10,
+ .pagesz = 2,
+ .trcd = 1375,
+ .trcmin = 4875,
+ .trasmin = 3500,
+};
+
+static void ccgr_init(void)
+{
+ struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ writel(0xFFFFFFFF, &ccm->CCGR0);
+ writel(0xFFFFFFFF, &ccm->CCGR1);
+ writel(0xFFFFFFFF, &ccm->CCGR2);
+ writel(0xFFFFFFFF, &ccm->CCGR3);
+ writel(0xFFFFFFFF, &ccm->CCGR4);
+ writel(0xFFFFFFFF, &ccm->CCGR5);
+ writel(0xFFFFFFFF, &ccm->CCGR6);
+ writel(0xFFFFFFFF, &ccm->CCGR7);
+}
+
+static void spl_dram_init(void)
+{
+ mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
+ mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
+}
+
+void board_init_f(ulong dummy)
+{
+ /* Setup AIPS and disable watchdog */
+ arch_cpu_init();
+
+ ccgr_init();
+
+ /* Setup iomux and i2c */
+ board_early_init_f();
+
+ /* Setup GP timer */
+ timer_init();
+
+ /* UART clocks enabled and gd valid - init serial console */
+ preloader_console_init();
+
+ /* DDR initialization */
+ spl_dram_init();
+}
--- /dev/null
+/*
+ * Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/mx6ul_pins.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/io.h>
+#include <common.h>
+#include <fsl_esdhc.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <mmc.h>
+#include <netdev.h>
+#include <usb.h>
+#include <usb/ehci-fsl.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \
+ PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
+ PAD_CTL_ODE)
+
+#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
+ PAD_CTL_SPEED_HIGH | \
+ PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST)
+
+#define MDIO_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
+ PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST | PAD_CTL_ODE)
+
+#define ENET_CLK_PAD_CTRL (PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_SPEED_HIGH | PAD_CTL_SRE_FAST)
+
+#define OTGID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
+ PAD_CTL_DSE_80ohm | PAD_CTL_HYS | \
+ PAD_CTL_SRE_FAST)
+
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+
+static struct i2c_pads_info i2c_pad_info1 = {
+ .scl = {
+ .i2c_mode = MX6_PAD_GPIO1_IO02__I2C1_SCL | PC,
+ .gpio_mode = MX6_PAD_GPIO1_IO02__GPIO1_IO02 | PC,
+ .gp = IMX_GPIO_NR(1, 2),
+ },
+ .sda = {
+ .i2c_mode = MX6_PAD_GPIO1_IO03__I2C1_SDA | PC,
+ .gpio_mode = MX6_PAD_GPIO1_IO03__GPIO1_IO03 | PC,
+ .gp = IMX_GPIO_NR(1, 3),
+ },
+};
+
+static struct i2c_pads_info i2c_pad_info2 = {
+ .scl = {
+ .i2c_mode = MX6_PAD_GPIO1_IO00__I2C2_SCL | PC,
+ .gpio_mode = MX6_PAD_GPIO1_IO00__GPIO1_IO00 | PC,
+ .gp = IMX_GPIO_NR(1, 0),
+ },
+ .sda = {
+ .i2c_mode = MX6_PAD_GPIO1_IO01__I2C2_SDA | PC,
+ .gpio_mode = MX6_PAD_GPIO1_IO01__GPIO1_IO01 | PC,
+ .gp = IMX_GPIO_NR(1, 1),
+ },
+};
+
+static struct i2c_pads_info i2c_pad_info4 = {
+ .scl = {
+ .i2c_mode = MX6_PAD_UART2_TX_DATA__I2C4_SCL | PC,
+ .gpio_mode = MX6_PAD_UART2_TX_DATA__GPIO1_IO20 | PC,
+ .gp = IMX_GPIO_NR(1, 20),
+ },
+ .sda = {
+ .i2c_mode = MX6_PAD_UART2_RX_DATA__I2C4_SDA | PC,
+ .gpio_mode = MX6_PAD_UART2_RX_DATA__GPIO1_IO21 | PC,
+ .gp = IMX_GPIO_NR(1, 21),
+ },
+};
+
+int dram_init(void)
+{
+ gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+
+ return 0;
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+ MX6_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart4_pads[] = {
+ MX6_PAD_UART4_TX_DATA__UART4_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_UART4_RX_DATA__UART4_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart5_pads[] = {
+ MX6_PAD_GPIO1_IO04__UART5_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_GPIO1_IO05__UART5_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_GPIO1_IO09__UART5_DCE_CTS | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_GPIO1_IO08__UART5_DCE_RTS | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart8_pads[] = {
+ MX6_PAD_ENET2_TX_DATA1__UART8_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_ENET2_TX_EN__UART8_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_ENET2_TX_CLK__UART8_DCE_CTS | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_ENET2_RX_ER__UART8_DCE_RTS | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+ imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+ imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
+ imx_iomux_v3_setup_multiple_pads(uart5_pads, ARRAY_SIZE(uart5_pads));
+ imx_iomux_v3_setup_multiple_pads(uart8_pads, ARRAY_SIZE(uart8_pads));
+}
+
+/* eMMC on USDHC2 */
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+ MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA04__USDHC2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA05__USDHC2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA06__USDHC2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA07__USDHC2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+ /*
+ * RST_B
+ */
+ MX6_PAD_NAND_ALE__USDHC2_RESET_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static struct fsl_esdhc_cfg usdhc_cfg = {
+ .esdhc_base = USDHC2_BASE_ADDR,
+ .max_bus_width = 8,
+};
+
+#define USDHC2_PWR_GPIO IMX_GPIO_NR(1, 9)
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ /* eMMC is always present */
+ return 1;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+
+ usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+
+ return fsl_esdhc_initialize(bis, &usdhc_cfg);
+}
+
+#define USB_OTHERREGS_OFFSET 0x800
+#define UCTRL_PWR_POL (1 << 9)
+
+static iomux_v3_cfg_t const usb_otg_pads[] = {
+ /* OTG1 */
+ MX6_PAD_SD1_CMD__USB_OTG1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_SD1_DATA0__ANATOP_OTG1_ID | MUX_PAD_CTRL(OTGID_PAD_CTRL),
+ /* OTG2 */
+ MX6_PAD_SD1_DATA1__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL),
+ MX6_PAD_SD1_DATA3__ANATOP_OTG2_ID | MUX_PAD_CTRL(OTGID_PAD_CTRL),
+};
+
+static void setup_usb(void)
+{
+ imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
+ ARRAY_SIZE(usb_otg_pads));
+}
+
+int board_usb_phy_mode(int port)
+{
+ if (port == 1)
+ return USB_INIT_HOST;
+ else
+ return usb_phy_mode(port);
+}
+
+int board_ehci_hcd_init(int port)
+{
+ u32 *usbnc_usb_ctrl;
+
+ if (port > 1)
+ return -EINVAL;
+
+ usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET +
+ port * 4);
+
+ /* Set Power polarity */
+ setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL);
+
+ return 0;
+}
+
+static iomux_v3_cfg_t const fec1_pads[] = {
+ MX6_PAD_GPIO1_IO06__ENET1_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL),
+ MX6_PAD_GPIO1_IO07__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET1_TX_DATA0__ENET1_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET1_TX_DATA1__ENET1_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET1_TX_EN__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
+ MX6_PAD_ENET1_RX_DATA0__ENET1_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET1_RX_DATA1__ENET1_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET1_RX_ER__ENET1_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET1_RX_EN__ENET1_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+
+ /* ENET1 reset */
+ MX6_PAD_CSI_MCLK__GPIO4_IO17 | MUX_PAD_CTRL(NO_PAD_CTRL),
+ /* ENET1 interrupt */
+ MX6_PAD_CSI_PIXCLK__GPIO4_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+#define ENET_PHY_RESET_GPIO IMX_GPIO_NR(4, 17)
+
+int board_eth_init(bd_t *bis)
+{
+ int ret;
+
+ imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
+
+ /* Reset LAN8742 PHY */
+ ret = gpio_request(ENET_PHY_RESET_GPIO, "phy-reset");
+ if (!ret)
+ gpio_direction_output(ENET_PHY_RESET_GPIO , 0);
+ mdelay(10);
+ gpio_set_value(ENET_PHY_RESET_GPIO, 1);
+ mdelay(10);
+
+ return cpu_eth_init(bis);
+}
+
+static int setup_fec(int fec_id)
+{
+ struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+ int ret;
+
+ /*
+ * Use 50M anatop loopback REF_CLK1 for ENET1,
+ * clear gpr1[13], set gpr1[17].
+ */
+ clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK,
+ IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK);
+
+ ret = enable_fec_anatop_clock(fec_id, ENET_50MHZ);
+ if (ret)
+ return ret;
+
+ enable_enet_clk(1);
+
+ return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
+ return 0;
+}
+
+int board_early_init_f(void)
+{
+ setup_iomux_uart();
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* Address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+ setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+ setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+ setup_i2c(3, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info4);
+
+ setup_fec(CONFIG_FEC_ENET_DEV);
+
+ setup_usb();
+
+ return 0;
+}
+
+static const struct boot_mode board_boot_modes[] = {
+ /* 8 bit bus width */
+ {"emmc", MAKE_CFGVAL(0x60, 0x28, 0x00, 0x00)},
+ { NULL, 0 },
+};
+
+int board_late_init(void)
+{
+ add_board_boot_modes(board_boot_modes);
+ setenv("board_name", "xpress");
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: CCV-EVA xPress\n");
+
+ return 0;
+}
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_TARGET_XPRESS=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/ccv/xpress/imximage.cfg"
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_PING=y
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_TARGET_XPRESS=y
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg"
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_PING=y
--- /dev/null
+/*
+ * Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
+ *
+ * Configuration settings for the CCV xPress board
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#ifndef __XPRESS_CONFIG_H
+#define __XPRESS_CONFIG_H
+
+#include "mx6_common.h"
+#include <asm/imx-common/gpio.h>
+
+/* SPL options */
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#include "imx6_spl.h"
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (16 << 20)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE UART1_BASE
+
+/* MMC Configs */
+#define CONFIG_SYS_FSL_ESDHC_ADDR USDHC2_BASE_ADDR
+#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
+
+/* I2C configs */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_MXC_I2C4 /* enable I2C bus 4 */
+#define CONFIG_SYS_I2C_SPEED 100000
+
+/* Miscellaneous configurable options */
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_MEMTEST_START 0x80000000
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x10000000)
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+#define CONFIG_SYS_HZ 1000
+
+#define CONFIG_SYS_CONSOLE_INFO_QUIET
+#define CONFIG_CMDLINE_EDITING
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
+#define PHYS_SDRAM_SIZE (128 << 20)
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+/* Environment is in stored in the eMMC boot partition */
+#define CONFIG_ENV_SIZE (16 << 10)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_ENV_OFFSET (512 << 10)
+#define CONFIG_SYS_MMC_ENV_DEV 0 /* USDHC2 */
+#define CONFIG_SYS_MMC_ENV_PART 1 /* boot parition */
+#define CONFIG_MMCROOT "/dev/mmcblk0p2" /* USDHC2 */
+
+#define CONFIG_OF_LIBFDT
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_CMD_BMODE
+#define CONFIG_CMD_CACHE
+
+/* USB Configs */
+#define CONFIG_CMD_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_MX6
+#define CONFIG_USB_STORAGE
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS 0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define CONFIG_CMD_MII
+#define CONFIG_FEC_ENET_DEV 0
+#define IMX_FEC_BASE ENET_BASE_ADDR
+#define CONFIG_FEC_MXC_PHYADDR 0x0
+#define CONFIG_FEC_XCV_TYPE RMII
+#define CONFIG_ETHPRIME "FEC"
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_SMSC
+
+#define CONFIG_IMX_THERMAL
+
+#define CONFIG_SYS_MMC_IMG_LOAD_PART 1
+
+#define CONFIG_UBOOT_SECTOR_START 0x2
+#define CONFIG_UBOOT_SECTOR_COUNT 0x3fe
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "script=boot.scr\0" \
+ "image=zImage\0" \
+ "console=ttymxc0\0" \
+ "fdt_high=0xffffffff\0" \
+ "initrd_high=0xffffffff\0" \
+ "fdt_file=undefined\0" \
+ "fdt_addr=0x83000000\0" \
+ "boot_fdt=try\0" \
+ "ip_dyn=yes\0" \
+ "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
+ "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
+ "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+ "mmcautodetect=yes\0" \
+ "mmcargs=setenv bootargs console=${console},${baudrate} " \
+ "root=${mmcroot}\0" \
+ "loadbootscript=" \
+ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
+ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if run loadfdt; then " \
+ "bootz ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootz; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "bootz; " \
+ "fi;\0" \
+ "uboot=ccv/u-boot.imx\0" \
+ "uboot_start="__stringify(CONFIG_UBOOT_SECTOR_START)"\0" \
+ "uboot_size="__stringify(CONFIG_UBOOT_SECTOR_COUNT)"\0" \
+ "update_uboot=if tftp ${uboot}; then " \
+ "if itest ${filesize} > 0; then " \
+ "mmc dev 0 1;" \
+ "setexpr blkc ${filesize} / 0x200;" \
+ "setexpr blkc ${blkc} + 1;" \
+ "if itest ${blkc} <= ${uboot_size}; then " \
+ "mmc write ${loadaddr} ${uboot_start} " \
+ "${blkc};" \
+ "fi;" \
+ "fi; fi;" \
+ "setenv filesize; setenv blkc\0" \
+ "update_bootpart=mmc bootbus 0 2 1 2;mmc partconf 0 1 1 0\0"
+
+#endif /* __XPRESS_CONFIG_H */
projects / u-boot / commitdiff