/*
- * (C) Copyright 2010
+ * (C) Copyright 2010-2011
* Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
* esd electronic system design gmbh <www.esd.eu>
*
*/
#include <common.h>
-#include <asm/arch/at91sam9263.h>
+#include <asm/io.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/at91_pmc.h>
#include <asm/arch/at91_matrix.h>
#include <asm/arch/at91_pio.h>
#include <asm/arch/clk.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/io.h>
-#include <atmel_lcdc.h>
-#include <lcd.h>
#include <netdev.h>
-#ifdef CONFIG_LCD_INFO
-#include <nand.h>
-#include <version.h>
+#ifdef CONFIG_LCD
+# include <atmel_lcdc.h>
+# include <lcd.h>
+# ifdef CONFIG_LCD_INFO
+# include <nand.h>
+# include <version.h>
+# endif
#endif
DECLARE_GLOBAL_DATA_PTR;
static void otc570_nand_hw_init(void)
{
unsigned long csa;
- at91_smc_t *smc = (at91_smc_t *) AT91_SMC0_BASE;
- at91_matrix_t *matrix = (at91_matrix_t *) AT91_MATRIX_BASE;
+ at91_smc_t *smc = (at91_smc_t *) ATMEL_BASE_SMC0;
+ at91_matrix_t *matrix = (at91_matrix_t *) ATMEL_BASE_MATRIX;
/* Enable CS3 */
csa = readl(&matrix->csa[0]) | AT91_MATRIX_CSA_EBI_CS3A;
&smc->cs[3].cycle);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
- AT91_SMC_MODE_DBW_8 |
- AT91_SMC_MODE_TDF_CYCLE(2),
+ AT91_SMC_MODE_DBW_8 |
+ AT91_SMC_MODE_TDF_CYCLE(3),
&smc->cs[3].mode);
/* Configure RDY/BSY */
#ifdef CONFIG_MACB
static void otc570_macb_hw_init(void)
{
- at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE;
+ at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
/* Enable clock */
- writel(1 << AT91SAM9263_ID_EMAC, &pmc->pcer);
+ writel(1 << ATMEL_ID_EMAC, &pmc->pcer);
at91_macb_hw_init();
}
#endif
*/
static void otc570_ethercat_hw_init(void)
{
- at91_smc_t *smc1 = (at91_smc_t *) AT91_SMC1_BASE;
+ at91_smc_t *smc1 = (at91_smc_t *) ATMEL_BASE_SMC1;
/* Configure SMC EBI1_CS0 for EtherCAT */
writel(AT91_SMC_SETUP_NWE(0) | AT91_SMC_SETUP_NCS_WR(0) |
.vl_sync = ATMEL_LCDC_INVLINE_INVERTED |
ATMEL_LCDC_INVFRAME_INVERTED,
- .vl_bpix = 3, /* Bits per pixel, 0 = 1bit, 3 = 8bit */
+ .vl_bpix = LCD_BPP,/* Bits per pixel, 0 = 1bit, 3 = 8bit */
.vl_tft = 1, /* 0 = passive, 1 = TFT */
.vl_vsync_len = 1, /* Length of vertical sync in NOL */
.vl_upper_margin = 35, /* Idle lines at the frame start */
.vl_left_margin = 112, /* Idle cycles at the line beginning */
.vl_right_margin = 1, /* Idle cycles at the end of the line */
- .mmio = AT91SAM9263_LCDC_BASE,
+ .mmio = ATMEL_BASE_LCDC,
};
void lcd_enable(void)
{
- at91_set_pio_value(AT91_PIO_PORTA, 30, 0); /* power up */
+ at91_set_pio_value(AT91_PIO_PORTA, 30, 0); /* power up */
}
void lcd_disable(void)
{
- at91_set_pio_value(AT91_PIO_PORTA, 30, 1); /* power down */
+ at91_set_pio_value(AT91_PIO_PORTA, 30, 1); /* power down */
}
static void otc570_lcd_hw_init(void)
{
- at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE;
+ at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
at91_set_a_periph(AT91_PIO_PORTC, 0, 0); /* LCDVSYNC */
at91_set_a_periph(AT91_PIO_PORTC, 1, 0); /* LCDHSYNC */
at91_set_a_periph(AT91_PIO_PORTC, 27, 0); /* LCDD23 */
at91_set_pio_output(AT91_PIO_PORTA, 30, 1); /* PCI */
- writel(1 << AT91SAM9263_ID_LCDC, &pmc->pcer);
- gd->fb_base = CONFIG_OTC570_LCD_BASE;
+ writel(1 << ATMEL_ID_LCDC, &pmc->pcer);
}
#ifdef CONFIG_LCD_INFO
nand_size += nand_info[i].size;
lcd_printf("\n%s\n", U_BOOT_VERSION);
- lcd_printf("%s CPU at %s MHz\n", CONFIG_SYS_AT91_CPU_NAME,
- strmhz(temp, get_cpu_clk_rate()));
+ lcd_printf("CPU at %s MHz\n", strmhz(temp, get_cpu_clk_rate()));
lcd_printf(" %ld MB SDRAM, %ld MB NAND\n",
dram_size >> 20,
nand_size >> 20 );
int dram_init(void)
{
- gd->bd->bi_dram[0].start = PHYS_SDRAM;
- gd->bd->bi_dram[0].size = get_ram_size((long *) PHYS_SDRAM, (1 << 27));
+ gd->ram_size = get_ram_size(
+ (void *)CONFIG_SYS_SDRAM_BASE,
+ CONFIG_SYS_SDRAM_SIZE);
return 0;
}
{
int rc = 0;
#ifdef CONFIG_MACB
- rc = macb_eth_initialize(0, (void *)AT91_EMAC_BASE, 0x00);
+ rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00);
#endif
return rc;
}
{
char str[32];
- puts("Board: esd ARM9 HMI Panel - OTC570");
+ puts("Board : esd ARM9 HMI Panel - OTC570");
if (getenv_f("serial#", str, sizeof(str)) > 0) {
puts(", serial# ");
puts(str);
}
- printf("\nHardware-revision: 1.%d\n", get_hw_rev());
- printf("Mach-type: %lu\n", gd->bd->bi_arch_number);
+ printf("\n");
+ printf("Hardware-revision: 1.%d\n", get_hw_rev());
+ printf("Mach-type : %lu\n", gd->bd->bi_arch_number);
return 0;
}
int misc_init_r(void)
{
char str[64];
- at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE;
+ at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
at91_set_pio_output(AT91_PIO_PORTA, 29, 1);
at91_set_a_periph(AT91_PIO_PORTA, 26, 1); /* TXD0 */
at91_set_a_periph(AT91_PIO_PORTA, 27, 0); /* RXD0 */
- writel(1 << AT91SAM9263_ID_US0, &pmc->pcer);
+ writel(1 << ATMEL_ID_USART0, &pmc->pcer);
/* Set USART_MODE = 1 (RS485) */
writel(1, 0xFFF8C004);
at91_set_pio_output(AT91_PIO_PORTA, 29, 0);
}
}
+#ifdef CONFIG_LCD
printf("Display memory address: 0x%08lX\n", gd->fb_base);
+#endif
return 0;
}
#endif /* CONFIG_MISC_INIT_R */
-int board_init(void)
+int board_early_init_f(void)
{
- at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE;
-
- /* Peripheral Clock Enable Register */
- writel( 1 << AT91SAM9263_ID_PIOA |
- 1 << AT91SAM9263_ID_PIOB |
- 1 << AT91SAM9263_ID_PIOCDE |
- 1 << AT91SAM9263_ID_TWI |
- 1 << AT91SAM9263_ID_SPI0 |
- 1 << AT91SAM9263_ID_LCDC |
- 1 << AT91SAM9263_ID_UHP,
+ at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
+
+ /* enable all clocks */
+ writel((1 << ATMEL_ID_PIOA) |
+ (1 << ATMEL_ID_PIOB) |
+ (1 << ATMEL_ID_PIOCDE) |
+ (1 << ATMEL_ID_TWI) |
+ (1 << ATMEL_ID_SPI0) |
+#ifdef CONFIG_LCD
+ (1 << ATMEL_ID_LCDC) |
+#endif
+ (1 << ATMEL_ID_UHP),
&pmc->pcer);
+ at91_seriald_hw_init();
+
/* arch number of OTC570-Board */
gd->bd->bi_arch_number = MACH_TYPE_OTC570;
+ return 0;
+}
+
+int board_init(void)
+{
+ /* initialize ET1100 Controller */
+ otc570_ethercat_hw_init();
+
/* adress of boot parameters */
- gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
- at91_serial_hw_init();
#ifdef CONFIG_CMD_NAND
otc570_nand_hw_init();
#endif
- otc570_ethercat_hw_init();
#ifdef CONFIG_HAS_DATAFLASH
at91_spi0_hw_init(1 << 0);
#endif
/*
- * (C) Copyright 2010
+ * (C) Copyright 2010-2011
* Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
* esd electronic system design gmbh <www.esd.eu>
*
#ifndef __CONFIG_H
#define __CONFIG_H
-/* Common stuff */
-#define CONFIG_OTC570 1 /* Board is esd OTC570 */
-#define CONFIG_ARM926EJS 1 /* This is an ARM926EJS Core */
-#define CONFIG_AT91SAM9263 1 /* It's an AT91SAM9263 SoC */
+/*
+ * SoC must be defined first, before hardware.h is included.
+ * In this case SoC is defined in boards.cfg.
+ */
+#include <asm/hardware.h>
+
+/*
+ * Warning: changing CONFIG_SYS_TEXT_BASE requires
+ * adapting the initial boot program.
+ * Since the linker has to swallow that define, we must use a pure
+ * hex number here!
+ */
+#define CONFIG_SYS_TEXT_BASE 0x20002000
+
+/* ARM asynchronous clock */
+#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* 32.768 kHz crystal */
#define CONFIG_SYS_AT91_MAIN_CLOCK 16000000/* 16.0 MHz crystal */
#define CONFIG_SYS_HZ 1000 /* decrementer freq */
-#define CONFIG_DISPLAY_BOARDINFO 1
-#define CONFIG_DISPLAY_CPUINFO 1 /* display cpu info and speed */
-#define CONFIG_PREBOOT /* enable preboot variable */
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
-#define CONFIG_SERIAL_TAG 1
-#define CONFIG_REVISION_TAG 1
-#undef CONFIG_USE_IRQ /* don't need IRQ/FIQ stuff */
+/* Misc CPU related */
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
-
#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f() */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_SERIAL_TAG
+#define CONFIG_REVISION_TAG
+#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
+#define CONFIG_MISC_INIT_R /* Call misc_init_r */
+#undef CONFIG_USE_IRQ /* don't need IRQ/FIQ stuff */
+
+#define CONFIG_DISPLAY_BOARDINFO /* call checkboard() */
+#define CONFIG_DISPLAY_CPUINFO /* display cpu info and speed */
+#define CONFIG_PREBOOT /* enable preboot variable */
/*
* Hardware drivers
*/
-#define CONFIG_AT91_GPIO 1
+
+/* required until arch/arm/include/asm/arch-at91/at91sam9263.h is reworked */
+#define ATMEL_PMC_UHP AT91SAM926x_PMC_UHP
+
+/* general purpose I/O */
+#define CONFIG_AT91_GPIO
/* Console output */
-#define CONFIG_ATMEL_USART 1
-#undef CONFIG_USART0
-#undef CONFIG_USART1
-#undef CONFIG_USART2
-#define CONFIG_USART3 1 /* USART 3 is DBGU */
+#define CONFIG_ATMEL_USART
+#define CONFIG_USART_BASE ATMEL_BASE_DBGU
+#define CONFIG_USART_ID ATMEL_ID_SYS
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE {115200, 19200, 38400, 57600, 9600}
#define CONFIG_BOOTDELAY 3
-#define CONFIG_ZERO_BOOTDELAY_CHECK 1
+#define CONFIG_ZERO_BOOTDELAY_CHECK
/* LCD */
-#define CONFIG_LCD 1
-#define LCD_BPP LCD_COLOR8
-
+#define CONFIG_LCD
#undef CONFIG_SPLASH_SCREEN
-#ifndef CONFIG_SPLASH_SCREEN
-#define CONFIG_LCD_LOGO 1
-#define CONFIG_LCD_INFO 1
-#undef CONFIG_LCD_INFO_BELOW_LOGO
-#endif /* CONFIG_SPLASH_SCREEN */
+#ifdef CONFIG_LCD
+# define LCD_BPP LCD_COLOR8
+
+# ifndef CONFIG_SPLASH_SCREEN
+# define CONFIG_LCD_LOGO
+# define CONFIG_LCD_INFO
+# undef CONFIG_LCD_INFO_BELOW_LOGO
+# endif /* CONFIG_SPLASH_SCREEN */
-#undef LCD_TEST_PATTERN
-#define CONFIG_SYS_WHITE_ON_BLACK 1
-#define CONFIG_ATMEL_LCD 1
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
-#define CONFIG_OTC570_LCD_BASE 0x23E00000 /* LCD is in SDRAM */
-#define CONFIG_CMD_BMP 1
+# undef LCD_TEST_PATTERN
+# define CONFIG_SYS_WHITE_ON_BLACK
+# define CONFIG_ATMEL_LCD
+# define CONFIG_SYS_CONSOLE_IS_IN_ENV
+# define CONFIG_OTC570_LCD_BASE (CONFIG_SYS_SDRAM_BASE + 0x03fa5000)
+# define CONFIG_CMD_BMP
+#endif /* CONFIG_LCD */
/* RTC and I2C stuff */
-#define CONFIG_RTC_DS1338 1
+#define CONFIG_RTC_DS1338
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
#undef CONFIG_HARD_I2C
-#define CONFIG_SOFT_I2C 1
+#define CONFIG_SOFT_I2C
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_I2C_SLAVE 0x7F
#ifdef CONFIG_SOFT_I2C
-#define CONFIG_I2C_CMD_TREE 1
-#define CONFIG_I2C_MULTI_BUS 1
+# define CONFIG_I2C_CMD_TREE
+# define CONFIG_I2C_MULTI_BUS
/* Configure data and clock pins for pio */
-#define I2C_INIT { \
+# define I2C_INIT { \
at91_set_pio_output(AT91_PIO_PORTB, 4, 0); \
at91_set_pio_output(AT91_PIO_PORTB, 5, 0); \
}
-#define I2C_SOFT_DECLARATIONS
+# define I2C_SOFT_DECLARATIONS
/* Configure data pin as output */
-#define I2C_ACTIVE at91_set_pio_output(AT91_PIO_PORTB, 4, 0)
+# define I2C_ACTIVE at91_set_pio_output(AT91_PIO_PORTB, 4, 0)
/* Configure data pin as input */
-#define I2C_TRISTATE at91_set_pio_input(AT91_PIO_PORTB, 4, 0)
+# define I2C_TRISTATE at91_set_pio_input(AT91_PIO_PORTB, 4, 0)
/* Read data pin */
-#define I2C_READ at91_get_pio_value(AT91_PIO_PORTB, 4)
+# define I2C_READ at91_get_pio_value(AT91_PIO_PORTB, 4)
/* Set data pin */
-#define I2C_SDA(bit) at91_set_pio_value(AT91_PIO_PORTB, 4, bit)
+# define I2C_SDA(bit) at91_set_pio_value(AT91_PIO_PORTB, 4, bit)
/* Set clock pin */
-#define I2C_SCL(bit) at91_set_pio_value(AT91_PIO_PORTB, 5, bit)
-#define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */
+# define I2C_SCL(bit) at91_set_pio_value(AT91_PIO_PORTB, 5, bit)
+# define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */
#endif /* CONFIG_SOFT_I2C */
-#define CONFIG_BOOTDELAY 3
-#define CONFIG_ZERO_BOOTDELAY_CHECK 1
-
/*
* BOOTP options
*/
-#define CONFIG_BOOTP_BOOTFILESIZE 1
-#define CONFIG_BOOTP_BOOTPATH 1
-#define CONFIG_BOOTP_GATEWAY 1
-#define CONFIG_BOOTP_HOSTNAME 1
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
#undef CONFIG_CMD_LOADS
#undef CONFIG_CMD_IMLS
-#define CONFIG_CMD_PING 1
-#define CONFIG_CMD_DHCP 1
-#define CONFIG_CMD_NAND 1
-#define CONFIG_CMD_USB 1
-#define CONFIG_CMD_I2C 1
-#define CONFIG_CMD_DATE 1
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_DATE
/* LED */
-#define CONFIG_AT91_LED 1
+#define CONFIG_AT91_LED
-/* SDRAM */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM 0x20000000
+/*
+ * SDRAM: 1 bank, min 32, max 128 MB
+ * Initialized before u-boot gets started.
+ */
+#define CONFIG_NR_DRAM_BANKS 1
+#define CONFIG_SYS_SDRAM_BASE 0x20000000 /* ATMEL_BASE_CS1 */
+#define CONFIG_SYS_SDRAM_SIZE 0x04000000
+
+#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE + 0x00100000)
+#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x01E00000)
+#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x00100000)
+
+/*
+ * Initial stack pointer: 4k - GENERATED_GBL_DATA_SIZE in internal SRAM,
+ * leaving the correct space for initial global data structure above
+ * that address while providing maximum stack area below.
+ */
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (ATMEL_BASE_SRAM0 + 0x1000 - GENERATED_GBL_DATA_SIZE)
/* DataFlash */
-#define CONFIG_ATMEL_DATAFLASH_SPI
-#define CONFIG_HAS_DATAFLASH 1
-#define CONFIG_SYS_SPI_WRITE_TOUT (5 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_MAX_DATAFLASH_BANKS 1
-#define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* CS0 */
-#define AT91_SPI_CLK 15000000
-#define DATAFLASH_TCSS (0x1a << 16)
-#define DATAFLASH_TCHS (0x1 << 24)
+#ifdef CONFIG_SYS_USE_DATAFLASH
+# define CONFIG_ATMEL_DATAFLASH_SPI
+# define CONFIG_HAS_DATAFLASH
+# define CONFIG_SYS_SPI_WRITE_TOUT (5 * CONFIG_SYS_HZ)
+# define CONFIG_SYS_MAX_DATAFLASH_BANKS 1
+# define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* CS0 */
+# define AT91_SPI_CLK 15000000
+# define DATAFLASH_TCSS (0x1a << 16)
+# define DATAFLASH_TCHS (0x1 << 24)
+#endif
/* NOR flash is not populated, disable it */
-#define CONFIG_SYS_NO_FLASH 1
+#define CONFIG_SYS_NO_FLASH
/* NAND flash */
#ifdef CONFIG_CMD_NAND
-#define CONFIG_NAND_ATMEL
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE 0x40000000
-#define CONFIG_SYS_NAND_DBW_8 1
-/* our ALE is AD21 */
-#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
-/* our CLE is AD22 */
-#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
-#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIO_PORTD, 15
-#define CONFIG_SYS_NAND_READY_PIN AT91_PIO_PORTA, 22
-#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */
+# define CONFIG_NAND_ATMEL
+# define CONFIG_SYS_MAX_NAND_DEVICE 1
+# define CONFIG_SYS_NAND_BASE 0x40000000 /* ATMEL_BASE_CS3 */
+# define CONFIG_SYS_NAND_DBW_8
+# define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
+# define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
+# define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIO_PORTD, 15
+# define CONFIG_SYS_NAND_READY_PIN AT91_PIO_PORTA, 22
+# define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */
#endif
/* Ethernet */
-#define CONFIG_MACB 1
-#define CONFIG_RMII 1
-#define CONFIG_NET_MULTI 1
+#define CONFIG_MACB
+#define CONFIG_RMII
+#define CONFIG_NET_MULTI
+#define CONFIG_FIT
#define CONFIG_NET_RETRY_COUNT 20
#undef CONFIG_RESET_PHY_R
/* USB */
#define CONFIG_USB_ATMEL
-#define CONFIG_USB_OHCI_NEW 1
-#define CONFIG_DOS_PARTITION 1
-#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
+#define CONFIG_USB_OHCI_NEW
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SYS_USB_OHCI_CPU_INIT
#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00a00000
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9263"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
-#define CONFIG_USB_STORAGE 1
-#define CONFIG_CMD_FAT 1
-
-#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
-
-#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
-#define CONFIG_SYS_MEMTEST_END 0x23e00000
-
-#define CONFIG_SYS_USE_DATAFLASH 1
-#undef CONFIG_SYS_USE_NANDFLASH
+#define CONFIG_USB_STORAGE
+#define CONFIG_CMD_FAT
/* CAN */
-#define CONFIG_AT91_CAN 1
+#define CONFIG_AT91_CAN
/* hw-controller addresses */
-#define CONFIG_ET1100_BASE 0x70000000
+#define CONFIG_ET1100_BASE 0x70000000 /* ATMEL_BASE_CS6 */
+
+#ifdef CONFIG_SYS_USE_DATAFLASH
/* bootstrap + u-boot + env in dataflash on CS0 */
-#define CONFIG_ENV_IS_IN_DATAFLASH 1
-#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + \
+# define CONFIG_ENV_IS_IN_DATAFLASH
+# define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + \
0x8400)
-#define CONFIG_ENV_OFFSET 0x4200
-#define CONFIG_ENV_ADDR (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + \
+# define CONFIG_ENV_OFFSET 0x4200
+# define CONFIG_ENV_ADDR (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + \
CONFIG_ENV_OFFSET)
-#define CONFIG_ENV_SIZE 0x4200
+# define CONFIG_ENV_SIZE 0x4200
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 }
+#elif CONFIG_SYS_USE_NANDFLASH
+
+/* bootstrap + u-boot + env + linux in nandflash */
+# define CONFIG_ENV_IS_IN_NAND 1
+# define CONFIG_ENV_OFFSET 0xC0000
+# define CONFIG_ENV_SIZE 0x20000
+
+#endif
#define CONFIG_SYS_PROMPT "=> "
-#define CONFIG_SYS_CBSIZE 256
+#define CONFIG_SYS_CBSIZE 512
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_LONGHELP 1
-#define CONFIG_CMDLINE_EDITING 1
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CMDLINE_EDITING
/*
* Size of malloc() pool
#define CONFIG_STACKSIZE (32 * 1024) /* regular stack */
#ifdef CONFIG_USE_IRQ
-#error CONFIG_USE_IRQ not supported
+# error CONFIG_USE_IRQ not supported
#endif
#endif
projects / u-boot / commitdiff