This board is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
config TARGET_IVMS8
bool "Support IVMS8"
-config TARGET_LWMON
- bool "Support lwmon"
-
config TARGET_TQM823L
bool "Support TQM823L"
source "board/esteem192e/Kconfig"
source "board/ip860/Kconfig"
source "board/ivm/Kconfig"
-source "board/lwmon/Kconfig"
source "board/tqc/tqm8xx/Kconfig"
endmenu
/* ------------------------------------------------------------------------- */
-#ifndef CONFIG_LWMON
-
int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
ulong msr, addr;
return 1;
}
-#else /* CONFIG_LWMON */
-
-/*
- * On the LWMON board, the MCLR reset input of the PIC's on the board
- * uses a 47K/1n RC combination which has a 47us time constant. The
- * low signal on the HRESET pin of the CPU is only 512 clocks = 8 us
- * and thus too short to reset the external hardware. So we use the
- * watchdog to reset the board.
- */
-int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
- /* prevent triggering the watchdog */
- disable_interrupts ();
-
- /* make sure the watchdog is running */
- reset_8xx_watchdog ((immap_t *) CONFIG_SYS_IMMR);
-
- /* wait for watchdog reset */
- while (1) {};
-
- /* NOTREACHED */
- return 1;
-}
-
-#endif /* CONFIG_LWMON */
-
/* ------------------------------------------------------------------------- */
/*
}
#endif /* CONFIG_WATCHDOG */
-#if defined(CONFIG_WATCHDOG) || defined(CONFIG_LWMON)
+#if defined(CONFIG_WATCHDOG)
void reset_8xx_watchdog (volatile immap_t * immr)
{
-# if defined(CONFIG_LWMON)
- /*
- * The LWMON board uses a MAX6301 Watchdog
- * with the trigger pin connected to port PA.7
- *
- * (The old board version used a MAX706TESA Watchdog, which
- * had to be handled exactly the same.)
- */
-# define WATCHDOG_BIT 0x0100
- immr->im_ioport.iop_papar &= ~(WATCHDOG_BIT); /* GPIO */
- immr->im_ioport.iop_padir |= WATCHDOG_BIT; /* Output */
- immr->im_ioport.iop_paodr &= ~(WATCHDOG_BIT); /* active output */
-
- immr->im_ioport.iop_padat ^= WATCHDOG_BIT; /* Toggle WDI */
-# else
/*
* All other boards use the MPC8xx Internal Watchdog
*/
immr->im_siu_conf.sc_swsr = 0x556c; /* write magic1 */
immr->im_siu_conf.sc_swsr = 0xaa39; /* write magic2 */
-# endif /* CONFIG_LWMON */
}
#endif /* CONFIG_WATCHDOG */
#if defined(CONFIG_IP860) || \
defined(CONFIG_IVML24) || \
defined(CONFIG_IVMS8) || \
- defined(CONFIG_LWMON) || \
defined(CONFIG_RMU)
memctl->memc_br0 = CONFIG_SYS_BR0_PRELIM;
#include <commproc.h>
#include <i2c.h>
-#ifdef CONFIG_LWMON
-#include <watchdog.h>
-#endif
DECLARE_GLOBAL_DATA_PTR;
uchar xaddr[4];
int rc;
-#ifdef CONFIG_LWMON
- WATCHDOG_RESET();
-#endif
-
xaddr[0] = (addr >> 24) & 0xFF;
xaddr[1] = (addr >> 16) & 0xFF;
xaddr[2] = (addr >> 8) & 0xFF;
volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
-#if defined(CONFIG_LWMON)
- reset_phy();
-#endif
-
pram_ptr = (scc_enet_t *) & (immr->im_cpm.cp_dparam[PROFF_ENET]);
rxIdx = 0;
sp = (scc_t *) &(cp->cp_scc[SCC_INDEX]);
up = (scc_uart_t *) &cp->cp_dparam[PROFF_SCC];
-#if defined(CONFIG_LWMON) && defined(CONFIG_8xx_CONS_SCC2)
- { /* Disable Ethernet, enable Serial */
- uchar c;
-
- c = pic_read (0x61);
- c &= ~0x40; /* enable COM3 */
- c |= 0x80; /* disable Ethernet */
- pic_write (0x61, c);
-
- /* enable RTS2 */
- cp->cp_pbpar |= 0x2000;
- cp->cp_pbdat |= 0x2000;
- cp->cp_pbdir |= 0x2000;
- }
-#endif /* CONFIG_LWMON */
-
/* Disable transmitter/receiver. */
sp->scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
#if defined(CONFIG_WD_MAX_RATE)
unsigned long long wdt_last; /* trace watch-dog triggering rate */
#endif
-#if defined(CONFIG_LWMON) || defined(CONFIG_LWMON5)
+#if defined(CONFIG_LWMON5)
unsigned long kbd_status;
#endif
};
+++ /dev/null
-if TARGET_LWMON
-
-config SYS_BOARD
- default "lwmon"
-
-config SYS_CONFIG_NAME
- default "lwmon"
-
-endif
+++ /dev/null
-LWMON BOARD
-M: Wolfgang Denk <wd@denx.de>
-S: Maintained
-F: board/lwmon/
-F: include/configs/lwmon.h
-F: configs/lwmon_defconfig
+++ /dev/null
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y = lwmon.o flash.o pcmcia.o
+++ /dev/null
-
-Tastaturabfrage:
-
-Die Implementierung / Decodierung beruht auf den Angaben aus dem Do-
-kument "PIC LWE-Tastatur" in der Fassung vom 9. 3. 2001, insbesonde-
-re Tabelle 3 im Kapitel 4.3 Tastencodes. In U-Boot werden die vom
-Keyboard-Controller gelesenen Daten hexadezimal codiert in der auto-
-matisch angelegten Environment-Variablen "keybd" übergeben. Ist kei-
-ne Taste gedrückt worden, steht dort:
-
- keybd=000000000000000000
-
-Der decodierte Tastencode ("keybd") kann mit den "bootargs" an den
-Linux-Kernel übergeben und dort z. B. in einem Device-Treiber oder
-einer Applikation ausgewertet werden.
-
-
-Sonderfunktionen beim Booten:
-
-Es lassen sich eine oder mehrere (beliebig viele) Tasten oder Tasten-
-kombinationen definieren, die Sonderfunktionen auslösen, wenn diese
-Tasten beim Booten (Reset) gedrückt sind.
-
-Wird eine eingestellte Taste bzw. Tastenkombination erkannt, so wird
-in U-Boot noch vor dem Start des "Countdown" und somit vor jedem an-
-deren Kommando der Inhalt einer dieser Taste bzw. Tastenkombination
-zugeordneten Environment-Variablen ausführen.
-
-
-Die Environment-Variable "magic_keys" wird als Liste von Zeichen ver-
-standen, die als Suffix an den Namen "key_magic" angefügt werden und
-so die Namen der Environment-Variablen definieren, mit denen die
-Tasten (-kombinationen) festgelegt werden:
-
-Ist "magic_keys" NICHT definiert, so wird nur die in der Environment-
-Variablen "key_magic" codierte Tasten (-kombination) geprüft, und
-ggf. der Inhalt der Environment-Variablen "key_cmd" ausgeführt (ge-
-nauer: der Inhalt von "key_cmd" wird der Variablen "preboot" zugewie-
-sen, die ausgeführt wird, unmittelbar bevor die interaktive Kommando-
-interpretation beginnt).
-
-Enthält "magic_keys" z. B. die Zeichenkette "0123CB*", so werden
-nacheinander folgende Aktionen ausgeführt:
-
- prüfe Tastencode ggf. führe aus Kommando
- in Variable in Variable
- -----------------------------------
- key_magic0 ==> key_cmd0
- key_magic1 ==> key_cmd1
- key_magic2 ==> key_cmd2
- key_magic3 ==> key_cmd3
- key_magicC ==> key_cmdC
- key_magicB ==> key_cmdB
- key_magicA ==> key_cmdA
- key_magic* ==> key_cmd*
-
-Hinweis: sobald ein aktivierter Tastencode erkannt wurde, wird die
-Bearbeitung abgebrochen; es wird daher höchstens eines der definier-
-ten Kommandos ausgeführt, wobei die Priorität durch die Suchreihen-
-folge festgelegt wird, also durch die Reihenfolge der Zeichen in der
-Varuiablen "magic_keys".
-
-
-Die Codierung der Tasten, die beim Booten gedrückt werden müssen, um
-eine Funktion auszulösen, erfolgt nach der Tastaturtabelle.
-
-Die Definitionen
-
- => setenv key_magic0 3a+3b
- => setenv key_cmd0 setenv bootdelay 30
-
-bedeuten dementsprechend, daß die Tasten mit den Codes 0x3A (Taste
-"F1") und 0x3B (Taste "F2") gleichzeitig gedrückt werden müssen. Sie
-können dort eine beliebige Tastenkombination eintragen (jeweils 2
-Zeichen für die Hex-Codes der Tasten, und '+' als Trennzeichen).
-
-Wird die eingestellte Tastenkombination erkannt, so wird in U-Boot
-noch vor dem Start des "Countdown" und somit vor jedem anderen Kom-
-mando das angebene Kommando ausgeführt und somit ein langes Boot-
-Delay eingetragen.
-
-Praktisch könnten Sie also in U-Boot "bootdelay" auf 0 setzen und
-somit stets ohne jede User-Interaktion automatisch booten, außer,
-wenn die beiden Tasten "F1" und "F2" beim Booten gedrückt werden:
-dann würde ein Boot-Delay von 30 Sekunden eingefügt.
-
-
-Hinweis: dem Zeichen '#' kommt innerhalb von "magic_keys" eine beson-
-dere Bedeutung zu: die dadurch definierte Key-Sequenz schaltet den
-Monitor in den "Debug-Modus" - das bedeutet zunächst, daß alle weite-
-ren Meldungen von U-Boot über das LCD-Display ausgegeben werden;
-außerdem kann man durch das mit dieser Tastenkombination verknüpfte
-Kommando z. B. die Linux-Bootmeldungen ebenfalls auf das LCD-Display
-legen, so daß der Boot-Vorgang direkt und ohne weitere Hilfsmittel
-analysiert werden kann.
-
-Beispiel:
-
-In U-Boot werden folgende Environment-Variablen gesetzt und abgespei-
-chert:
-
-(1) => setenv magic_keys 01234#X
-(2) => setenv key_cmd# setenv addfb setenv bootargs \\${bootargs} console=tty0 console=ttyS1,\\${baudrate}
-(3) => setenv nfsargs setenv bootargs root=/dev/nfs rw nfsroot=\${serverip}:\${rootpath}
-(4) => setenv addip setenv bootargs \${bootargs} ip=\${ipaddr}:\${serverip}:\${gatewayip}:\${netmask}:\${hostname}::off panic=1
-(5) => setenv addfb setenv bootargs \${bootargs} console=ttyS1,\${baudrate}
-(6) => setenv bootcmd bootp\;run nfsargs\;run addip\;run addfb\;bootm
-
-Hierbei wird die Linux Commandline (in der Variablen "bootargs") im
-Boot-Kommando "bootcmd" (6) schrittweise zusammengesetzt: zunächst
-werden die für Root-Filesystem über NFS erforderlichen Optionen ge-
-setzt ("run nfsargs", vgl. (3)), dann die Netzwerkkonfiguration an-
-gefügt ("run addip", vgl. (4)), und schließlich die Systemconsole
-definiert ("run addfb").
-
-Dabei wird im Normalfall die Definition (5) verwendt; wurde aller-
-dings beim Reset die entsprechende Taste gedrückt gehalten, so wird
-diese Definition bei der Ausführung des in (2) definierten Kommandos
-überschrieben, so daß Linux die Bootmeldungen auch über das Frame-
-buffer-Device (=LCD-Display) ausgibt.
-
-Beachten Sie die Verdoppelung der '\'-Escapes in der Definition von
-"key_cmd#" - diese ist erforderlich, weil der String _zweimal_ inter-
-pretiert wird: das erste Mal bei der Eingabe von "key_cmd#", das
-zweite Mal, wenn der String (als Inhalt von "preboot") ausgeführt
-wird.
+++ /dev/null
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/* #define DEBUG */
-
-#include <common.h>
-#include <mpc8xx.h>
-
-#if defined(CONFIG_ENV_IS_IN_FLASH)
-# ifndef CONFIG_ENV_ADDR
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
-# endif
-# ifndef CONFIG_ENV_SIZE
-# define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-# endif
-# ifndef CONFIG_ENV_SECT_SIZE
-# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
-# endif
-#endif
-
-/*---------------------------------------------------------------------*/
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (vu_long *addr, flash_info_t *info);
-static int write_data (flash_info_t *info, ulong dest, ulong data);
-#ifdef CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-static int write_data_buf (flash_info_t * info, ulong dest, uchar * cp, int len);
-#endif
-static void flash_get_offsets (ulong base, flash_info_t *info);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
- volatile immap_t *immap = (immap_t *)CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- unsigned long size_b0, size_b1;
- int i;
-
- /* Init: no FLASHes known */
- for (i=0; i<CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
- flash_info[i].flash_id = FLASH_UNKNOWN;
- }
-
- /* Static FLASH Bank configuration here - FIXME XXX */
-
- debug ("\n## Get flash bank 1 size @ 0x%08x\n",FLASH_BASE0_PRELIM);
-
- size_b0 = flash_get_size((vu_long *)FLASH_BASE0_PRELIM, &flash_info[0]);
-
- if (flash_info[0].flash_id == FLASH_UNKNOWN) {
- printf ("## Unknown FLASH on Bank 0: "
- "ID 0x%lx, Size = 0x%08lx = %ld MB\n",
- flash_info[0].flash_id,
- size_b0, size_b0<<20);
- }
-
- debug ("## Get flash bank 2 size @ 0x%08x\n",FLASH_BASE1_PRELIM);
-
- size_b1 = flash_get_size((vu_long *)FLASH_BASE1_PRELIM, &flash_info[1]);
-
- debug ("## Prelim. Flash bank sizes: %08lx + 0x%08lx\n",size_b0,size_b1);
-
- if (size_b1 > size_b0) {
- printf ("## ERROR: "
- "Bank 1 (0x%08lx = %ld MB) > Bank 0 (0x%08lx = %ld MB)\n",
- size_b1, size_b1<<20,
- size_b0, size_b0<<20
- );
- flash_info[0].flash_id = FLASH_UNKNOWN;
- flash_info[1].flash_id = FLASH_UNKNOWN;
- flash_info[0].sector_count = -1;
- flash_info[1].sector_count = -1;
- flash_info[0].size = 0;
- flash_info[1].size = 0;
- return (0);
- }
-
- debug ("## Before remap: "
- "BR0: 0x%08x OR0: 0x%08x "
- "BR1: 0x%08x OR1: 0x%08x\n",
- memctl->memc_br0, memctl->memc_or0,
- memctl->memc_br1, memctl->memc_or1);
-
- /* Remap FLASH according to real size */
- memctl->memc_or0 = (-size_b0 & 0xFFFF8000) | CONFIG_SYS_OR_TIMING_FLASH |
- OR_CSNT_SAM | OR_ACS_DIV1;
- memctl->memc_br0 = (CONFIG_SYS_FLASH_BASE & BR_BA_MSK) | BR_PS_32 | BR_V;
-
- debug ("## BR0: 0x%08x OR0: 0x%08x\n",
- memctl->memc_br0, memctl->memc_or0);
-
- /* Re-do sizing to get full correct info */
- size_b0 = flash_get_size((vu_long *)CONFIG_SYS_FLASH_BASE, &flash_info[0]);
-
- flash_get_offsets (CONFIG_SYS_FLASH_BASE, &flash_info[0]);
-
- flash_info[0].size = size_b0;
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- /* monitor protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE+monitor_flash_len-1,
- &flash_info[0]);
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
- /* ENV protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR+CONFIG_ENV_SECT_SIZE-1,
- &flash_info[0]);
-#endif
-
- if (size_b1) {
- memctl->memc_or1 = (-size_b1 & 0xFFFF8000) | CONFIG_SYS_OR_TIMING_FLASH |
- OR_CSNT_SAM | OR_ACS_DIV1;
- memctl->memc_br1 = ((CONFIG_SYS_FLASH_BASE + size_b0) & BR_BA_MSK) |
- BR_PS_32 | BR_V;
-
- debug ("## BR1: 0x%08x OR1: 0x%08x\n",
- memctl->memc_br1, memctl->memc_or1);
-
- /* Re-do sizing to get full correct info */
- size_b1 = flash_get_size((vu_long *)(CONFIG_SYS_FLASH_BASE + size_b0),
- &flash_info[1]);
-
- flash_info[1].size = size_b1;
-
- flash_get_offsets (CONFIG_SYS_FLASH_BASE + size_b0, &flash_info[1]);
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- /* monitor protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE+monitor_flash_len-1,
- &flash_info[1]);
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
- /* ENV protection ON by default */
- flash_protect(FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR+CONFIG_ENV_SECT_SIZE-1,
- &flash_info[1]);
-#endif
- } else {
- memctl->memc_br1 = 0; /* invalidate bank */
- memctl->memc_or1 = 0; /* invalidate bank */
-
- debug ("## DISABLE BR1: 0x%08x OR1: 0x%08x\n",
- memctl->memc_br1, memctl->memc_or1);
-
- flash_info[1].flash_id = FLASH_UNKNOWN;
- flash_info[1].sector_count = -1;
- flash_info[1].size = 0;
- }
-
- debug ("## Final Flash bank sizes: %08lx + 0x%08lx\n",size_b0,size_b1);
-
- return (size_b0 + size_b1);
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t *info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_INTEL:
- for (i = 0; i < info->sector_count; i++) {
- info->start[i] = base;
- base += 0x00020000 * 2; /* 128k * 2 chips per bank */
- }
- return;
-
- default:
- printf ("Don't know sector ofsets for flash type 0x%lx\n",
- info->flash_id);
- return;
- }
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t *info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_AMD: printf ("AMD "); break;
- case FLASH_MAN_FUJ: printf ("Fujitsu "); break;
- case FLASH_MAN_SST: printf ("SST "); break;
- case FLASH_MAN_STM: printf ("STM "); break;
- case FLASH_MAN_INTEL: printf ("Intel "); break;
- case FLASH_MAN_MT: printf ("MT "); break;
- default: printf ("Unknown Vendor "); break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_28F320J3A: printf ("28F320J3A (32Mbit = 128K x 32)\n");
- break;
- case FLASH_28F640J3A: printf ("28F640J3A (64Mbit = 128K x 64)\n");
- break;
- case FLASH_28F128J3A: printf ("28F128J3A (128Mbit = 128K x 128)\n");
- break;
- default: printf ("Unknown Chip Type\n");
- break;
- }
-
- if (info->size >= (1 << 20)) {
- i = 20;
- } else {
- i = 10;
- }
- printf (" Size: %ld %cB in %d Sectors\n",
- info->size >> i,
- (i == 20) ? 'M' : 'k',
- info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i=0; i<info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf ("\n ");
- printf (" %08lX%s",
- info->start[i],
- info->protect[i] ? " (RO)" : " "
- );
- }
- printf ("\n");
- return;
-}
-
-/*-----------------------------------------------------------------------
- */
-
-
-/*-----------------------------------------------------------------------
- */
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-static ulong flash_get_size (vu_long *addr, flash_info_t *info)
-{
- ulong value;
-
- /* Read Manufacturer ID */
- addr[0] = 0x00900090;
- value = addr[0];
-
- debug ("Manuf. ID @ 0x%08lx: 0x%08lx\n", (ulong)addr, value);
-
- switch (value) {
- case AMD_MANUFACT:
- info->flash_id = FLASH_MAN_AMD;
- break;
- case FUJ_MANUFACT:
- info->flash_id = FLASH_MAN_FUJ;
- break;
- case SST_MANUFACT:
- info->flash_id = FLASH_MAN_SST;
- break;
- case STM_MANUFACT:
- info->flash_id = FLASH_MAN_STM;
- break;
- case INTEL_MANUFACT:
- info->flash_id = FLASH_MAN_INTEL;
- break;
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- addr[0] = 0x00FF00FF; /* restore read mode */
- return (0); /* no or unknown flash */
- }
-
- value = addr[1]; /* device ID */
-
- debug ("Device ID @ 0x%08lx: 0x%08lx\n", (ulong)(&addr[1]), value);
-
- switch (value) {
- case INTEL_ID_28F320J3A:
- info->flash_id += FLASH_28F320J3A;
- info->sector_count = 32;
- info->size = 0x00400000 * 2;
- break; /* => 8 MB */
-
- case INTEL_ID_28F640J3A:
- info->flash_id += FLASH_28F640J3A;
- info->sector_count = 64;
- info->size = 0x00800000 * 2;
- break; /* => 16 MB */
-
- case INTEL_ID_28F128J3A:
- info->flash_id += FLASH_28F128J3A;
- info->sector_count = 128;
- info->size = 0x01000000 * 2;
- break; /* => 32 MB */
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- addr[0] = 0x00FF00FF; /* restore read mode */
- return (0); /* => no or unknown flash */
-
- }
-
- if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) {
- printf ("** ERROR: sector count %d > max (%d) **\n",
- info->sector_count, CONFIG_SYS_MAX_FLASH_SECT);
- info->sector_count = CONFIG_SYS_MAX_FLASH_SECT;
- }
-
- addr[0] = 0x00FF00FF; /* restore read mode */
-
- return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t *info, int s_first, int s_last)
-{
- int flag, prot, sect;
- ulong start, now, last;
-
- debug ("flash_erase: first: %d last: %d\n", s_first, s_last);
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- if ((info->flash_id & FLASH_VENDMASK) != FLASH_MAN_INTEL) {
- printf ("Can erase only Intel flash types - aborted\n");
- return 1;
- }
-
- prot = 0;
- for (sect=s_first; sect<=s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf ("\n");
- }
-
- start = get_timer (0);
- last = start;
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect<=s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- vu_long *addr = (vu_long *)(info->start[sect]);
- unsigned long status;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- *addr = 0x00600060; /* clear lock bit setup */
- *addr = 0x00D000D0; /* clear lock bit confirm */
-
- udelay (1000);
- /* This takes awfully long - up to 50 ms and more */
- while (((status = *addr) & 0x00800080) != 0x00800080) {
- if ((now=get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- *addr = 0x00FF00FF; /* reset to read mode */
- return 1;
- }
-
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- putc ('.');
- last = now;
- }
- udelay (1000); /* to trigger the watchdog */
- }
-
- *addr = 0x00500050; /* clear status register */
- *addr = 0x00200020; /* erase setup */
- *addr = 0x00D000D0; /* erase confirm */
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- /* wait at least 80us - let's wait 1 ms */
- udelay (1000);
-
- while (((status = *addr) & 0x00800080) != 0x00800080) {
- if ((now=get_timer(start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- *addr = 0x00B000B0; /* suspend erase */
- *addr = 0x00FF00FF; /* reset to read mode */
- return 1;
- }
-
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- putc ('.');
- last = now;
- }
- udelay (1000); /* to trigger the watchdog */
- }
-
- *addr = 0x00FF00FF; /* reset to read mode */
- }
- }
- printf (" done\n");
- return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- * 4 - Flash not identified
- */
-
-#define FLASH_WIDTH 4 /* flash bus width in bytes */
-
-int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
- ulong cp, wp, data;
- int i, l, rc;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- return 4;
- }
-
- wp = (addr & ~(FLASH_WIDTH-1)); /* get lower FLASH_WIDTH aligned address */
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i=0, cp=wp; i<l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
- for (; i<FLASH_WIDTH && cnt>0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt==0 && i<FLASH_WIDTH; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
-
- if ((rc = write_data(info, wp, data)) != 0) {
- return (rc);
- }
- wp += FLASH_WIDTH;
- }
-
- /*
- * handle FLASH_WIDTH aligned part
- */
-#ifdef CONFIG_SYS_FLASH_USE_BUFFER_WRITE
- while(cnt >= FLASH_WIDTH) {
- i = CONFIG_SYS_FLASH_BUFFER_SIZE > cnt ?
- (cnt & ~(FLASH_WIDTH - 1)) : CONFIG_SYS_FLASH_BUFFER_SIZE;
- if((rc = write_data_buf(info, wp, src,i)) != 0)
- return rc;
- wp += i;
- src += i;
- cnt -=i;
- }
-#else
- while (cnt >= FLASH_WIDTH) {
- data = 0;
- for (i=0; i<FLASH_WIDTH; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_data(info, wp, data)) != 0) {
- return (rc);
- }
- wp += FLASH_WIDTH;
- cnt -= FLASH_WIDTH;
- }
-#endif /* CONFIG_SYS_FLASH_USE_BUFFER_WRITE */
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i=0, cp=wp; i<FLASH_WIDTH && cnt>0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i<FLASH_WIDTH; ++i, ++cp) {
- data = (data << 8) | (*(uchar *)cp);
- }
-
- return (write_data(info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Check flash status, returns:
- * 0 - OK
- * 1 - timeout
- */
-static int flash_status_check(vu_long *addr, ulong tout, char * prompt)
-{
- ulong status;
- ulong start;
-
- /* Wait for command completion */
- start = get_timer (0);
- while(((status = *addr) & 0x00800080) != 0x00800080) {
- if (get_timer(start) > tout) {
- printf("Flash %s timeout at address %p\n", prompt, addr);
- *addr = 0x00FF00FF; /* restore read mode */
- return (1);
- }
- }
- return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_data (flash_info_t *info, ulong dest, ulong data)
-{
- vu_long *addr = (vu_long *)dest;
- int flag;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*addr & data) != data) {
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts();
-
- *addr = 0x00400040; /* write setup */
- *addr = data;
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts();
-
- if (flash_status_check(addr, CONFIG_SYS_FLASH_WRITE_TOUT, "write") != 0) {
- return (1);
- }
-
- *addr = 0x00FF00FF; /* restore read mode */
-
- return (0);
-}
-
-#ifdef CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-/*-----------------------------------------------------------------------
- * Write a buffer to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- */
-static int write_data_buf(flash_info_t * info, ulong dest, uchar * cp, int len)
-{
- vu_long *addr = (vu_long *)dest;
- int sector;
- int cnt;
- int retcode;
- vu_long * src = (vu_long *)cp;
- vu_long * dst = (vu_long *)dest;
-
- /* find sector */
- for(sector = info->sector_count - 1; sector >= 0; sector--) {
- if(dest >= info->start[sector])
- break;
- }
-
- *addr = 0x00500050; /* clear status */
- *addr = 0x00e800e8; /* write buffer */
-
- if((retcode = flash_status_check(addr, CONFIG_SYS_FLASH_BUFFER_WRITE_TOUT,
- "write to buffer")) == 0) {
- cnt = len / FLASH_WIDTH;
- *addr = (cnt-1) | ((cnt-1) << 16);
- while(cnt-- > 0) {
- *dst++ = *src++;
- }
- *addr = 0x00d000d0; /* write buffer confirm */
- retcode = flash_status_check(addr, CONFIG_SYS_FLASH_BUFFER_WRITE_TOUT,
- "buffer write");
- }
- *addr = 0x00FF00FF; /* restore read mode */
- *addr = 0x00500050; /* clear status */
- return retcode;
-}
-#endif /* CONFIG_SYS_USE_FLASH_BUFFER_WRITE */
-
-/*-----------------------------------------------------------------------
- */
+++ /dev/null
-/***********************************************************************
- *
-M* Modul: lwmon.c
-M*
-M* Content: LWMON specific U-Boot commands.
- *
- * (C) Copyright 2001, 2002
- * DENX Software Engineering
- * Wolfgang Denk, wd@denx.de
- *
-D* Design: wd@denx.de
-C* Coding: wd@denx.de
-V* Verification: dzu@denx.de
- *
- * SPDX-License-Identifier: GPL-2.0+
- ***********************************************************************/
-
-/*---------------------------- Headerfiles ----------------------------*/
-#include <common.h>
-#include <mpc8xx.h>
-#include <commproc.h>
-#include <i2c.h>
-#include <command.h>
-#include <malloc.h>
-#include <post.h>
-#include <serial.h>
-
-#include <linux/types.h>
-#include <linux/string.h> /* for strdup */
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/*------------------------ Local prototypes ---------------------------*/
-static long int dram_size (long int, long int *, long int);
-static void kbd_init (void);
-static int compare_magic (uchar *kbd_data, uchar *str);
-
-
-/*--------------------- Local macros and constants --------------------*/
-#define _NOT_USED_ 0xFFFFFFFF
-
-#ifdef CONFIG_MODEM_SUPPORT
-static int key_pressed(void);
-extern void disable_putc(void);
-#endif /* CONFIG_MODEM_SUPPORT */
-
-/*
- * 66 MHz SDRAM access using UPM A
- */
-const uint sdram_table[] =
-{
-#if defined(CONFIG_SYS_MEMORY_75) || defined(CONFIG_SYS_MEMORY_8E)
- /*
- * Single Read. (Offset 0 in UPM RAM)
- */
- 0x1F0DFC04, 0xEEAFBC04, 0x11AF7C04, 0xEFBAFC00,
- 0x1FF5FC47, /* last */
- /*
- * SDRAM Initialization (offset 5 in UPM RAM)
- *
- * This is no UPM entry point. The following definition uses
- * the remaining space to establish an initialization
- * sequence, which is executed by a RUN command.
- *
- */
- 0x1FF5FC34, 0xEFEABC34, 0x1FB57C35, /* last */
- /*
- * Burst Read. (Offset 8 in UPM RAM)
- */
- 0x1F0DFC04, 0xEEAFBC04, 0x10AF7C04, 0xF0AFFC00,
- 0xF0AFFC00, 0xF1AFFC00, 0xEFBAFC00, 0x1FF5FC47, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Single Write. (Offset 18 in UPM RAM)
- */
- 0x1F2DFC04, 0xEEABBC00, 0x01B27C04, 0x1FF5FC47, /* last */
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Burst Write. (Offset 20 in UPM RAM)
- */
- 0x1F0DFC04, 0xEEABBC00, 0x10A77C00, 0xF0AFFC00,
- 0xF0AFFC00, 0xE1BAFC04, 0x01FF5FC47, /* last */
- _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Refresh (Offset 30 in UPM RAM)
- */
- 0x1FFD7C84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
- 0xFFFFFC84, 0xFFFFFC07, /* last */
- _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Exception. (Offset 3c in UPM RAM)
- */
- 0x7FFFFC07, /* last */
- 0xFFFFFCFF, 0xFFFFFCFF, 0xFFFFFCFF,
-#endif
-#ifdef CONFIG_SYS_MEMORY_7E
- /*
- * Single Read. (Offset 0 in UPM RAM)
- */
- 0x0E2DBC04, 0x11AF7C04, 0xEFBAFC00, 0x1FF5FC47, /* last */
- _NOT_USED_,
- /*
- * SDRAM Initialization (offset 5 in UPM RAM)
- *
- * This is no UPM entry point. The following definition uses
- * the remaining space to establish an initialization
- * sequence, which is executed by a RUN command.
- *
- */
- 0x1FF5FC34, 0xEFEABC34, 0x1FB57C35, /* last */
- /*
- * Burst Read. (Offset 8 in UPM RAM)
- */
- 0x0E2DBC04, 0x10AF7C04, 0xF0AFFC00, 0xF0AFFC00,
- 0xF1AFFC00, 0xEFBAFC00, 0x1FF5FC47, /* last */
- _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Single Write. (Offset 18 in UPM RAM)
- */
- 0x0E29BC04, 0x01B27C04, 0x1FF5FC47, /* last */
- _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Burst Write. (Offset 20 in UPM RAM)
- */
- 0x0E29BC04, 0x10A77C00, 0xF0AFFC00, 0xF0AFFC00,
- 0xE1BAFC04, 0x1FF5FC47, /* last */
- _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Refresh (Offset 30 in UPM RAM)
- */
- 0x1FFD7C84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
- 0xFFFFFC84, 0xFFFFFC07, /* last */
- _NOT_USED_, _NOT_USED_,
- _NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
- /*
- * Exception. (Offset 3c in UPM RAM)
- */
- 0x7FFFFC07, /* last */
- 0xFFFFFCFF, 0xFFFFFCFF, 0xFFFFFCFF,
-#endif
-};
-
-/*
- * Check Board Identity:
- *
- */
-
-/***********************************************************************
-F* Function: int checkboard (void) P*A*Z*
- *
-P* Parameters: none
-P*
-P* Returnvalue: int - 0 is always returned
- *
-Z* Intention: This function is the checkboard() method implementation
-Z* for the lwmon board. Only a standard message is printed.
- *
-D* Design: wd@denx.de
-C* Coding: wd@denx.de
-V* Verification: dzu@denx.de
- ***********************************************************************/
-int checkboard (void)
-{
- puts ("Board: LICCON Konsole LCD3\n");
- return (0);
-}
-
-/***********************************************************************
-F* Function: phys_size_t initdram (int board_type) P*A*Z*
- *
-P* Parameters: int board_type
-P* - Usually type of the board - ignored here.
-P*
-P* Returnvalue: long int
-P* - Size of initialized memory
- *
-Z* Intention: This function is the initdram() method implementation
-Z* for the lwmon board.
-Z* The memory controller is initialized to access the
-Z* DRAM.
- *
-D* Design: wd@denx.de
-C* Coding: wd@denx.de
-V* Verification: dzu@denx.de
- ***********************************************************************/
-phys_size_t initdram (int board_type)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immr->im_memctl;
- long int size_b0;
- long int size8, size9;
- int i;
-
- /*
- * Configure UPMA for SDRAM
- */
- upmconfig (UPMA, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint));
-
- memctl->memc_mptpr = CONFIG_SYS_MPTPR;
-
- /* burst length=4, burst type=sequential, CAS latency=2 */
- memctl->memc_mar = CONFIG_SYS_MAR;
-
- /*
- * Map controller bank 3 to the SDRAM bank at preliminary address.
- */
- memctl->memc_or3 = CONFIG_SYS_OR3_PRELIM;
- memctl->memc_br3 = CONFIG_SYS_BR3_PRELIM;
-
- /* initialize memory address register */
- memctl->memc_mamr = CONFIG_SYS_MAMR_8COL; /* refresh not enabled yet */
-
- /* mode initialization (offset 5) */
- udelay (200); /* 0x80006105 */
- memctl->memc_mcr = MCR_OP_RUN | MCR_MB_CS3 | MCR_MLCF (1) | MCR_MAD (0x05);
-
- /* run 2 refresh sequence with 4-beat refresh burst (offset 0x30) */
- udelay (1); /* 0x80006130 */
- memctl->memc_mcr = MCR_OP_RUN | MCR_MB_CS3 | MCR_MLCF (1) | MCR_MAD (0x30);
- udelay (1); /* 0x80006130 */
- memctl->memc_mcr = MCR_OP_RUN | MCR_MB_CS3 | MCR_MLCF (1) | MCR_MAD (0x30);
-
- udelay (1); /* 0x80006106 */
- memctl->memc_mcr = MCR_OP_RUN | MCR_MB_CS3 | MCR_MLCF (1) | MCR_MAD (0x06);
-
- memctl->memc_mamr |= MAMR_PTAE; /* refresh enabled */
-
- udelay (200);
-
- /* Need at least 10 DRAM accesses to stabilize */
- for (i = 0; i < 10; ++i) {
- volatile unsigned long *addr =
- (volatile unsigned long *) SDRAM_BASE3_PRELIM;
- unsigned long val;
-
- val = *(addr + i);
- *(addr + i) = val;
- }
-
- /*
- * Check Bank 0 Memory Size for re-configuration
- *
- * try 8 column mode
- */
- size8 = dram_size (CONFIG_SYS_MAMR_8COL, (long *)SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE);
-
- udelay (1000);
-
- /*
- * try 9 column mode
- */
- size9 = dram_size (CONFIG_SYS_MAMR_9COL, (long *)SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE);
-
- if (size8 < size9) { /* leave configuration at 9 columns */
- size_b0 = size9;
- memctl->memc_mamr = CONFIG_SYS_MAMR_9COL | MAMR_PTAE;
- udelay (500);
- } else { /* back to 8 columns */
- size_b0 = size8;
- memctl->memc_mamr = CONFIG_SYS_MAMR_8COL | MAMR_PTAE;
- udelay (500);
- }
-
- /*
- * Final mapping:
- */
-
- memctl->memc_or3 = ((-size_b0) & 0xFFFF0000) |
- OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING;
- memctl->memc_br3 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
- udelay (1000);
-
- return (size_b0);
-}
-
-/***********************************************************************
-F* Function: static long int dram_size (long int mamr_value,
-F* long int *base,
-F* long int maxsize) P*A*Z*
- *
-P* Parameters: long int mamr_value
-P* - Value for MAMR for the test
-P* long int *base
-P* - Base address for the test
-P* long int maxsize
-P* - Maximum size to test for
-P*
-P* Returnvalue: long int
-P* - Size of probed memory
- *
-Z* Intention: Check memory range for valid RAM. A simple memory test
-Z* determines the actually available RAM size between
-Z* addresses `base' and `base + maxsize'. Some (not all)
-Z* hardware errors are detected:
-Z* - short between address lines
-Z* - short between data lines
- *
-D* Design: wd@denx.de
-C* Coding: wd@denx.de
-V* Verification: dzu@denx.de
- ***********************************************************************/
-static long int dram_size (long int mamr_value, long int *base, long int maxsize)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immr->im_memctl;
-
- memctl->memc_mamr = mamr_value;
-
- return (get_ram_size(base, maxsize));
-}
-
-/* ------------------------------------------------------------------------- */
-
-#ifndef PB_ENET_TENA
-# define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-#endif
-
-/***********************************************************************
-F* Function: int board_early_init_f (void) P*A*Z*
- *
-P* Parameters: none
-P*
-P* Returnvalue: int
-P* - 0 is always returned.
- *
-Z* Intention: This function is the board_early_init_f() method implementation
-Z* for the lwmon board.
-Z* Disable Ethernet TENA on Port B.
- *
-D* Design: wd@denx.de
-C* Coding: wd@denx.de
-V* Verification: dzu@denx.de
- ***********************************************************************/
-int board_early_init_f (void)
-{
- volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
-
- /* Disable Ethernet TENA on Port B
- * Necessary because of pull up in COM3 port.
- *
- * This is just a preliminary fix, intended to turn off TENA
- * as soon as possible to avoid noise on the network. Once
- * I2C is running we will make sure the interface is
- * correctly initialized.
- */
- immr->im_cpm.cp_pbpar &= ~PB_ENET_TENA;
- immr->im_cpm.cp_pbodr &= ~PB_ENET_TENA;
- immr->im_cpm.cp_pbdat &= ~PB_ENET_TENA; /* set to 0 = disabled */
- immr->im_cpm.cp_pbdir |= PB_ENET_TENA;
-
- return (0);
-}
-
-/* ------------------------------------------------------------------------- */
-
-/***********************************************************************
-F* Function: void reset_phy (void) P*A*Z*
- *
-P* Parameters: none
-P*
-P* Returnvalue: none
- *
-Z* Intention: Reset the PHY. In the lwmon case we do this by the
-Z* signaling the PIC I/O expander.
- *
-D* Design: wd@denx.de
-C* Coding: wd@denx.de
-V* Verification: dzu@denx.de
- ***********************************************************************/
-void reset_phy (void)
-{
- uchar c;
-
-#ifdef DEBUG
- printf ("### Switch on Ethernet for SCC2 ###\n");
-#endif
- c = pic_read (0x61);
-#ifdef DEBUG
- printf ("Old PIC read: reg_61 = 0x%02x\n", c);
-#endif
- c |= 0x40; /* disable COM3 */
- c &= ~0x80; /* enable Ethernet */
- pic_write (0x61, c);
-#ifdef DEBUG
- c = pic_read (0x61);
- printf ("New PIC read: reg_61 = 0x%02x\n", c);
-#endif
- udelay (1000);
-}
-
-
-/*------------------------- Keyboard controller -----------------------*/
-/* command codes */
-#define KEYBD_CMD_READ_KEYS 0x01
-#define KEYBD_CMD_READ_VERSION 0x02
-#define KEYBD_CMD_READ_STATUS 0x03
-#define KEYBD_CMD_RESET_ERRORS 0x10
-
-/* status codes */
-#define KEYBD_STATUS_MASK 0x3F
-#define KEYBD_STATUS_H_RESET 0x20
-#define KEYBD_STATUS_BROWNOUT 0x10
-#define KEYBD_STATUS_WD_RESET 0x08
-#define KEYBD_STATUS_OVERLOAD 0x04
-#define KEYBD_STATUS_ILLEGAL_WR 0x02
-#define KEYBD_STATUS_ILLEGAL_RD 0x01
-
-/* Number of bytes returned from Keyboard Controller */
-#define KEYBD_VERSIONLEN 2 /* version information */
-#define KEYBD_DATALEN 9 /* normal key scan data */
-
-/* maximum number of "magic" key codes that can be assigned */
-
-static uchar kbd_addr = CONFIG_SYS_I2C_KEYBD_ADDR;
-
-static uchar *key_match (uchar *);
-
-#define KEYBD_SET_DEBUGMODE '#' /* Magic key to enable debug output */
-
-/***********************************************************************
-F* Function: int board_postclk_init (void) P*A*Z*
- *
-P* Parameters: none
-P*
-P* Returnvalue: int
-P* - 0 is always returned.
- *
-Z* Intention: This function is the board_postclk_init() method implementation
-Z* for the lwmon board.
- *
- ***********************************************************************/
-int board_postclk_init (void)
-{
- kbd_init();
-
-#ifdef CONFIG_MODEM_SUPPORT
- if (key_pressed()) {
- disable_putc(); /* modem doesn't understand banner etc */
- gd->do_mdm_init = 1;
- }
-#endif
-
- return (0);
-}
-
-struct serial_device * default_serial_console (void)
-{
- return gd->do_mdm_init ? &serial_scc_device : &serial_smc_device;
-}
-
-static void kbd_init (void)
-{
- uchar kbd_data[KEYBD_DATALEN];
- uchar tmp_data[KEYBD_DATALEN];
- uchar val, errcd;
- int i;
-
- i2c_set_bus_num(0);
-
- gd->arch.kbd_status = 0;
-
- /* Forced by PIC. Delays <= 175us loose */
- udelay(1000);
-
- /* Read initial keyboard error code */
- val = KEYBD_CMD_READ_STATUS;
- i2c_write (kbd_addr, 0, 0, &val, 1);
- i2c_read (kbd_addr, 0, 0, &errcd, 1);
- /* clear unused bits */
- errcd &= KEYBD_STATUS_MASK;
- /* clear "irrelevant" bits. Recommended by Martin Rajek, LWN */
- errcd &= ~(KEYBD_STATUS_H_RESET|KEYBD_STATUS_BROWNOUT);
- if (errcd) {
- gd->arch.kbd_status |= errcd << 8;
- }
- /* Reset error code and verify */
- val = KEYBD_CMD_RESET_ERRORS;
- i2c_write (kbd_addr, 0, 0, &val, 1);
- udelay(1000); /* delay NEEDED by keyboard PIC !!! */
-
- val = KEYBD_CMD_READ_STATUS;
- i2c_write (kbd_addr, 0, 0, &val, 1);
- i2c_read (kbd_addr, 0, 0, &val, 1);
-
- val &= KEYBD_STATUS_MASK; /* clear unused bits */
- if (val) { /* permanent error, report it */
- gd->arch.kbd_status |= val;
- return;
- }
-
- /*
- * Read current keyboard state.
- *
- * After the error reset it may take some time before the
- * keyboard PIC picks up a valid keyboard scan - the total
- * scan time is approx. 1.6 ms (information by Martin Rajek,
- * 28 Sep 2002). We read a couple of times for the keyboard
- * to stabilize, using a big enough delay.
- * 10 times should be enough. If the data is still changing,
- * we use what we get :-(
- */
-
- memset (tmp_data, 0xFF, KEYBD_DATALEN); /* impossible value */
- for (i=0; i<10; ++i) {
- val = KEYBD_CMD_READ_KEYS;
- i2c_write (kbd_addr, 0, 0, &val, 1);
- i2c_read (kbd_addr, 0, 0, kbd_data, KEYBD_DATALEN);
-
- if (memcmp(kbd_data, tmp_data, KEYBD_DATALEN) == 0) {
- /* consistent state, done */
- break;
- }
- /* remeber last state, delay, and retry */
- memcpy (tmp_data, kbd_data, KEYBD_DATALEN);
- udelay (5000);
- }
-}
-
-/***********************************************************************
-F* Function: int misc_init_r (void) P*A*Z*
- *
-P* Parameters: none
-P*
-P* Returnvalue: int
-P* - 0 is always returned, even in the case of a keyboard
-P* error.
- *
-Z* Intention: This function is the misc_init_r() method implementation
-Z* for the lwmon board.
-Z* The keyboard controller is initialized and the result
-Z* of a read copied to the environment variable "keybd".
-Z* If KEYBD_SET_DEBUGMODE is defined, a check is made for
-Z* this key, and if found display to the LCD will be enabled.
-Z* The keys in "keybd" are checked against the magic
-Z* keycommands defined in the environment.
-Z* See also key_match().
- *
-D* Design: wd@denx.de
-C* Coding: wd@denx.de
-V* Verification: dzu@denx.de
- ***********************************************************************/
-int misc_init_r (void)
-{
- uchar kbd_data[KEYBD_DATALEN];
- char keybd_env[2 * KEYBD_DATALEN + 1];
- uchar kbd_init_status = gd->arch.kbd_status >> 8;
- uchar kbd_status = gd->arch.kbd_status;
- uchar val;
- char *str;
- int i;
-
- if (kbd_init_status) {
- printf ("KEYBD: Error %02X\n", kbd_init_status);
- }
- if (kbd_status) { /* permanent error, report it */
- printf ("*** Keyboard error code %02X ***\n", kbd_status);
- sprintf (keybd_env, "%02X", kbd_status);
- setenv ("keybd", keybd_env);
- return 0;
- }
-
- /*
- * Now we know that we have a working keyboard, so disable
- * all output to the LCD except when a key press is detected.
- */
-
- if ((console_assign (stdout, "serial") < 0) ||
- (console_assign (stderr, "serial") < 0)) {
- printf ("Can't assign serial port as output device\n");
- }
-
- /* Read Version */
- val = KEYBD_CMD_READ_VERSION;
- i2c_write (kbd_addr, 0, 0, &val, 1);
- i2c_read (kbd_addr, 0, 0, kbd_data, KEYBD_VERSIONLEN);
- printf ("KEYBD: Version %d.%d\n", kbd_data[0], kbd_data[1]);
-
- /* Read current keyboard state */
- val = KEYBD_CMD_READ_KEYS;
- i2c_write (kbd_addr, 0, 0, &val, 1);
- i2c_read (kbd_addr, 0, 0, kbd_data, KEYBD_DATALEN);
-
- for (i = 0; i < KEYBD_DATALEN; ++i) {
- sprintf (keybd_env + i + i, "%02X", kbd_data[i]);
- }
- setenv ("keybd", keybd_env);
-
- str = strdup ((char *)key_match (kbd_data)); /* decode keys */
-#ifdef KEYBD_SET_DEBUGMODE
- if (kbd_data[0] == KEYBD_SET_DEBUGMODE) { /* set debug mode */
- if ((console_assign (stdout, "lcd") < 0) ||
- (console_assign (stderr, "lcd") < 0)) {
- printf ("Can't assign LCD display as output device\n");
- }
- }
-#endif /* KEYBD_SET_DEBUGMODE */
-#ifdef CONFIG_PREBOOT /* automatically configure "preboot" command on key match */
- setenv ("preboot", str); /* set or delete definition */
-#endif /* CONFIG_PREBOOT */
- if (str != NULL) {
- free (str);
- }
- return (0);
-}
-
-#ifdef CONFIG_PREBOOT
-
-static uchar kbd_magic_prefix[] = "key_magic";
-static uchar kbd_command_prefix[] = "key_cmd";
-
-static int compare_magic (uchar *kbd_data, uchar *str)
-{
- uchar compare[KEYBD_DATALEN-1];
- char *nxt;
- int i;
-
- /* Don't include modifier byte */
- memcpy (compare, kbd_data+1, KEYBD_DATALEN-1);
-
- for (; str != NULL; str = (*nxt) ? (uchar *)(nxt+1) : (uchar *)nxt) {
- uchar c;
- int k;
-
- c = (uchar) simple_strtoul ((char *)str, (char **) (&nxt), 16);
-
- if (str == (uchar *)nxt) { /* invalid character */
- break;
- }
-
- /*
- * Check if this key matches the input.
- * Set matches to zero, so they match only once
- * and we can find duplicates or extra keys
- */
- for (k = 0; k < sizeof(compare); ++k) {
- if (compare[k] == '\0') /* only non-zero entries */
- continue;
- if (c == compare[k]) { /* found matching key */
- compare[k] = '\0';
- break;
- }
- }
- if (k == sizeof(compare)) {
- return -1; /* unmatched key */
- }
- }
-
- /*
- * A full match leaves no keys in the `compare' array,
- */
- for (i = 0; i < sizeof(compare); ++i) {
- if (compare[i])
- {
- return -1;
- }
- }
-
- return 0;
-}
-
-/***********************************************************************
-F* Function: static uchar *key_match (uchar *kbd_data) P*A*Z*
- *
-P* Parameters: uchar *kbd_data
-P* - The keys to match against our magic definitions
-P*
-P* Returnvalue: uchar *
-P* - != NULL: Pointer to the corresponding command(s)
-P* NULL: No magic is about to happen
- *
-Z* Intention: Check if pressed key(s) match magic sequence,
-Z* and return the command string associated with that key(s).
-Z*
-Z* If no key press was decoded, NULL is returned.
-Z*
-Z* Note: the first character of the argument will be
-Z* overwritten with the "magic charcter code" of the
-Z* decoded key(s), or '\0'.
-Z*
-Z* Note: the string points to static environment data
-Z* and must be saved before you call any function that
-Z* modifies the environment.
- *
-D* Design: wd@denx.de
-C* Coding: wd@denx.de
-V* Verification: dzu@denx.de
- ***********************************************************************/
-static uchar *key_match (uchar *kbd_data)
-{
- char magic[sizeof (kbd_magic_prefix) + 1];
- uchar *suffix;
- char *kbd_magic_keys;
-
- /*
- * The following string defines the characters that can pe appended
- * to "key_magic" to form the names of environment variables that
- * hold "magic" key codes, i. e. such key codes that can cause
- * pre-boot actions. If the string is empty (""), then only
- * "key_magic" is checked (old behaviour); the string "125" causes
- * checks for "key_magic1", "key_magic2" and "key_magic5", etc.
- */
- if ((kbd_magic_keys = getenv ("magic_keys")) == NULL)
- kbd_magic_keys = "";
-
- /* loop over all magic keys;
- * use '\0' suffix in case of empty string
- */
- for (suffix=(uchar *)kbd_magic_keys; *suffix || suffix==(uchar *)kbd_magic_keys; ++suffix) {
- sprintf (magic, "%s%c", kbd_magic_prefix, *suffix);
-#if 0
- printf ("### Check magic \"%s\"\n", magic);
-#endif
- if (compare_magic(kbd_data, (uchar *)getenv(magic)) == 0) {
- char cmd_name[sizeof (kbd_command_prefix) + 1];
- char *cmd;
-
- sprintf (cmd_name, "%s%c", kbd_command_prefix, *suffix);
-
- cmd = getenv (cmd_name);
-#if 0
- printf ("### Set PREBOOT to $(%s): \"%s\"\n",
- cmd_name, cmd ? cmd : "<<NULL>>");
-#endif
- *kbd_data = *suffix;
- return ((uchar *)cmd);
- }
- }
-#if 0
- printf ("### Delete PREBOOT\n");
-#endif
- *kbd_data = '\0';
- return (NULL);
-}
-#endif /* CONFIG_PREBOOT */
-
-#ifdef CONFIG_LCD_INFO
-#include <lcd.h>
-#include <version.h>
-#include <timestamp.h>
-
-void lcd_show_board_info(void)
-{
- char temp[32];
-
- lcd_printf ("%s (%s - %s)\n", U_BOOT_VERSION, U_BOOT_DATE, U_BOOT_TIME);
- lcd_printf ("(C) 2008 DENX Software Engineering GmbH\n");
- lcd_printf (" Wolfgang DENK, wd@denx.de\n");
-#ifdef CONFIG_LCD_INFO_BELOW_LOGO
- lcd_printf ("MPC823 CPU at %s MHz\n",
- strmhz(temp, gd->cpu_clk));
- lcd_printf (" %ld MB RAM, %ld MB Flash\n",
- gd->ram_size >> 20,
- gd->bd->bi_flashsize >> 20 );
-#else
- /* leave one blank line */
- lcd_printf ("\nMPC823 CPU at %s MHz, %ld MB RAM, %ld MB Flash\n",
- strmhz(temp, gd->cpu_clk),
- gd->ram_size >> 20,
- gd->bd->bi_flashsize >> 20 );
-#endif /* CONFIG_LCD_INFO_BELOW_LOGO */
-}
-#endif /* CONFIG_LCD_INFO */
-
-/*---------------Board Special Commands: PIC read/write ---------------*/
-
-#if defined(CONFIG_CMD_BSP)
-/***********************************************************************
-F* Function: int do_pic (cmd_tbl_t *cmdtp, int flag,
-F* int argc, char * const argv[]) P*A*Z*
- *
-P* Parameters: cmd_tbl_t *cmdtp
-P* - Pointer to our command table entry
-P* int flag
-P* - If the CMD_FLAG_REPEAT bit is set, then this call is
-P* a repetition
-P* int argc
-P* - Argument count
-P* char * const argv[]
-P* - Array of the actual arguments
-P*
-P* Returnvalue: int
-P* - 0 The command was handled successfully
-P* 1 An error occurred
- *
-Z* Intention: Implement the "pic [read|write]" commands.
-Z* The read subcommand takes one argument, the register,
-Z* whereas the write command takes two, the register and
-Z* the new value.
- *
-D* Design: wd@denx.de
-C* Coding: wd@denx.de
-V* Verification: dzu@denx.de
- ***********************************************************************/
-int do_pic (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
- uchar reg, val;
-
- switch (argc) {
- case 3: /* PIC read reg */
- if (strcmp (argv[1], "read") != 0)
- break;
-
- reg = simple_strtoul (argv[2], NULL, 16);
-
- printf ("PIC read: reg %02x: %02x\n\n", reg, pic_read (reg));
-
- return 0;
- case 4: /* PIC write reg val */
- if (strcmp (argv[1], "write") != 0)
- break;
-
- reg = simple_strtoul (argv[2], NULL, 16);
- val = simple_strtoul (argv[3], NULL, 16);
-
- printf ("PIC write: reg %02x val 0x%02x: %02x => ",
- reg, val, pic_read (reg));
- pic_write (reg, val);
- printf ("%02x\n\n", pic_read (reg));
- return 0;
- default:
- break;
- }
- return cmd_usage(cmdtp);
-}
-U_BOOT_CMD(
- pic, 4, 1, do_pic,
- "read and write PIC registers",
- "read reg - read PIC register `reg'\n"
- "pic write reg val - write value `val' to PIC register `reg'"
-);
-
-/***********************************************************************
-F* Function: int do_kbd (cmd_tbl_t *cmdtp, int flag,
-F* int argc, char * const argv[]) P*A*Z*
- *
-P* Parameters: cmd_tbl_t *cmdtp
-P* - Pointer to our command table entry
-P* int flag
-P* - If the CMD_FLAG_REPEAT bit is set, then this call is
-P* a repetition
-P* int argc
-P* - Argument count
-P* char * const argv[]
-P* - Array of the actual arguments
-P*
-P* Returnvalue: int
-P* - 0 is always returned.
- *
-Z* Intention: Implement the "kbd" command.
-Z* The keyboard status is read. The result is printed on
-Z* the console and written into the "keybd" environment
-Z* variable.
- *
-D* Design: wd@denx.de
-C* Coding: wd@denx.de
-V* Verification: dzu@denx.de
- ***********************************************************************/
-int do_kbd (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
- uchar kbd_data[KEYBD_DATALEN];
- char keybd_env[2 * KEYBD_DATALEN + 1];
- uchar val;
- int i;
-
-#if 0 /* Done in kbd_init */
- i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
-#endif
-
- /* Read keys */
- val = KEYBD_CMD_READ_KEYS;
- i2c_write (kbd_addr, 0, 0, &val, 1);
- i2c_read (kbd_addr, 0, 0, kbd_data, KEYBD_DATALEN);
-
- puts ("Keys:");
- for (i = 0; i < KEYBD_DATALEN; ++i) {
- sprintf (keybd_env + i + i, "%02X", kbd_data[i]);
- printf (" %02x", kbd_data[i]);
- }
- putc ('\n');
- setenv ("keybd", keybd_env);
- return 0;
-}
-
-U_BOOT_CMD(
- kbd, 1, 1, do_kbd,
- "read keyboard status",
- ""
-);
-
-/* Read and set LSB switch */
-#define CONFIG_SYS_PC_TXD1_ENA 0x0008 /* PC.12 */
-
-/***********************************************************************
-F* Function: int do_lsb (cmd_tbl_t *cmdtp, int flag,
-F* int argc, char * const argv[]) P*A*Z*
- *
-P* Parameters: cmd_tbl_t *cmdtp
-P* - Pointer to our command table entry
-P* int flag
-P* - If the CMD_FLAG_REPEAT bit is set, then this call is
-P* a repetition
-P* int argc
-P* - Argument count
-P* char * const argv[]
-P* - Array of the actual arguments
-P*
-P* Returnvalue: int
-P* - 0 The command was handled successfully
-P* 1 An error occurred
- *
-Z* Intention: Implement the "lsb [on|off]" commands.
-Z* The lsb is switched according to the first parameter by
-Z* by signaling the PIC I/O expander.
-Z* Called with no arguments, the current setting is
-Z* printed.
- *
-D* Design: wd@denx.de
-C* Coding: wd@denx.de
-V* Verification: dzu@denx.de
- ***********************************************************************/
-int do_lsb (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
- uchar val;
- immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
-
- switch (argc) {
- case 1: /* lsb - print setting */
- val = pic_read (0x60);
- printf ("LSB is o%s\n", (val & 0x20) ? "n" : "ff");
- return 0;
- case 2: /* lsb on or lsb off - set switch */
- val = pic_read (0x60);
-
- if (strcmp (argv[1], "on") == 0) {
- val |= 0x20;
- immr->im_ioport.iop_pcpar &= ~(CONFIG_SYS_PC_TXD1_ENA);
- immr->im_ioport.iop_pcdat |= CONFIG_SYS_PC_TXD1_ENA;
- immr->im_ioport.iop_pcdir |= CONFIG_SYS_PC_TXD1_ENA;
- } else if (strcmp (argv[1], "off") == 0) {
- val &= ~0x20;
- immr->im_ioport.iop_pcpar &= ~(CONFIG_SYS_PC_TXD1_ENA);
- immr->im_ioport.iop_pcdat &= ~(CONFIG_SYS_PC_TXD1_ENA);
- immr->im_ioport.iop_pcdir |= CONFIG_SYS_PC_TXD1_ENA;
- } else {
- break;
- }
- pic_write (0x60, val);
- return 0;
- default:
- break;
- }
- return cmd_usage(cmdtp);
-}
-
-U_BOOT_CMD(
- lsb, 2, 1, do_lsb,
- "check and set LSB switch",
- "on - switch LSB on\n"
- "lsb off - switch LSB off\n"
- "lsb - print current setting"
-);
-
-#endif
-
-/*----------------------------- Utilities -----------------------------*/
-/***********************************************************************
-F* Function: uchar pic_read (uchar reg) P*A*Z*
- *
-P* Parameters: uchar reg
-P* - Register to read
-P*
-P* Returnvalue: uchar
-P* - Value read from register
- *
-Z* Intention: Read a register from the PIC I/O expander.
- *
-D* Design: wd@denx.de
-C* Coding: wd@denx.de
-V* Verification: dzu@denx.de
- ***********************************************************************/
-uchar pic_read (uchar reg)
-{
- return (i2c_reg_read (CONFIG_SYS_I2C_PICIO_ADDR, reg));
-}
-
-/***********************************************************************
-F* Function: void pic_write (uchar reg, uchar val) P*A*Z*
- *
-P* Parameters: uchar reg
-P* - Register to read
-P* uchar val
-P* - Value to write
-P*
-P* Returnvalue: none
- *
-Z* Intention: Write to a register on the PIC I/O expander.
- *
-D* Design: wd@denx.de
-C* Coding: wd@denx.de
-V* Verification: dzu@denx.de
- ***********************************************************************/
-void pic_write (uchar reg, uchar val)
-{
- i2c_reg_write (CONFIG_SYS_I2C_PICIO_ADDR, reg, val);
-}
-
-/*---------------------- Board Control Functions ----------------------*/
-/***********************************************************************
-F* Function: void board_poweroff (void) P*A*Z*
- *
-P* Parameters: none
-P*
-P* Returnvalue: none
- *
-Z* Intention: Turn off the battery power and loop endless, so this
-Z* should better be the last function you call...
- *
-D* Design: wd@denx.de
-C* Coding: wd@denx.de
-V* Verification: dzu@denx.de
- ***********************************************************************/
-void board_poweroff (void)
-{
- /* Turn battery off */
- ((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcdat &= ~(1 << (31 - 13));
-
- while (1);
-}
-
-#ifdef CONFIG_MODEM_SUPPORT
-static int key_pressed(void)
-{
- uchar kbd_data[KEYBD_DATALEN];
- uchar val;
-
- /* Read keys */
- val = KEYBD_CMD_READ_KEYS;
- i2c_write (kbd_addr, 0, 0, &val, 1);
- i2c_read (kbd_addr, 0, 0, kbd_data, KEYBD_DATALEN);
-
- return (compare_magic(kbd_data, (uchar *)CONFIG_MODEM_KEY_MAGIC) == 0);
-}
-#endif /* CONFIG_MODEM_SUPPORT */
-
-#ifdef CONFIG_POST
-/*
- * Returns 1 if keys pressed to start the power-on long-running tests
- * Called from board_init_f().
- */
-int post_hotkeys_pressed(void)
-{
- uchar kbd_data[KEYBD_DATALEN];
- uchar val;
-
- /* Read keys */
- val = KEYBD_CMD_READ_KEYS;
- i2c_write (kbd_addr, 0, 0, &val, 1);
- i2c_read (kbd_addr, 0, 0, kbd_data, KEYBD_DATALEN);
-
- return (compare_magic(kbd_data, (uchar *)CONFIG_POST_KEY_MAGIC) == 0);
-}
-#endif
+++ /dev/null
-#include <common.h>
-#include <mpc8xx.h>
-#include <pcmcia.h>
-#include <i2c.h>
-
-#undef CONFIG_PCMCIA
-
-#if defined(CONFIG_CMD_PCMCIA)
-#define CONFIG_PCMCIA
-#endif
-
-#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
-#define CONFIG_PCMCIA
-#endif
-
-#ifdef CONFIG_PCMCIA
-
-#define PCMCIA_BOARD_MSG "LWMON"
-
-/* #define's for MAX1604 Power Switch */
-#define MAX1604_OP_SUS 0x80
-#define MAX1604_VCCBON 0x40
-#define MAX1604_VCC_35 0x20
-#define MAX1604_VCCBHIZ 0x10
-#define MAX1604_VPPBON 0x08
-#define MAX1604_VPPBPBPGM 0x04
-#define MAX1604_VPPBHIZ 0x02
-/* reserved 0x01 */
-
-int pcmcia_hardware_enable(int slot)
-{
- volatile pcmconf8xx_t *pcmp;
- volatile sysconf8xx_t *sysp;
- uint reg, mask;
- uchar val;
-
-
- debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- /* Switch on PCMCIA port in PIC register 0x60 */
- reg = pic_read (0x60);
- debug ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
- reg &= ~0x10;
- /* reg |= 0x08; Vpp not needed */
- pic_write (0x60, reg);
-#ifdef DEBUG
- reg = pic_read (0x60);
- printf ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
-#endif
- udelay(10000);
-
- sysp = (sysconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_siu_conf));
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
-
- /*
- * Configure SIUMCR to enable PCMCIA port B
- * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
- */
- sysp->sc_siumcr &= ~SIUMCR_DBGC11; /* set DBGC to 00 */
-
- /* clear interrupt state, and disable interrupts */
- pcmp->pcmc_pscr = PCMCIA_MASK(_slot_);
- pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
-
- /*
- * Disable interrupts, DMA, and PCMCIA buffers
- * (isolate the interface) and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Make sure there is a card in the slot, then configure the interface.
- */
- udelay(10000);
- debug ("[%d] %s: PIPR(%p)=0x%x\n",
- __LINE__,__FUNCTION__,
- &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
- if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
- printf (" No Card found\n");
- return (1);
- }
-
- /*
- * Power On.
- */
- mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
- reg = pcmp->pcmc_pipr;
- debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
- reg,
- (reg&PCMCIA_VS1(slot))?"n":"ff",
- (reg&PCMCIA_VS2(slot))?"n":"ff");
- if ((reg & mask) == mask) {
- val = 0; /* VCCB3/5 = 0 ==> use Vx = 5.0 V */
- puts (" 5.0V card found: ");
- } else {
- val = MAX1604_VCC_35; /* VCCB3/5 = 1 ==> use Vy = 3.3 V */
- puts (" 3.3V card found: ");
- }
-
- /* switch VCC on */
- val |= MAX1604_OP_SUS | MAX1604_VCCBON;
- i2c_set_bus_num(0);
- i2c_write (CONFIG_SYS_I2C_POWER_A_ADDR, 0, 0, &val, 1);
-
- udelay(500000);
-
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- udelay(250000); /* some cards need >150 ms to come up :-( */
-
- debug ("# hardware_enable done\n");
-
- return (0);
-}
-
-
-#if defined(CONFIG_CMD_PCMCIA)
-int pcmcia_hardware_disable(int slot)
-{
- volatile immap_t *immap;
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
- uchar val;
-
- debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
-
- immap = (immap_t *)CONFIG_SYS_IMMR;
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
-
- /* remove all power, put output in high impedance state */
- val = MAX1604_VCCBHIZ | MAX1604_VPPBHIZ;
- i2c_init (CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
- i2c_write (CONFIG_SYS_I2C_POWER_A_ADDR, 0, 0, &val, 1);
-
- /* Configure PCMCIA General Control Register */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = 0;
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
-
- /* Switch off PCMCIA port in PIC register 0x60 */
- reg = pic_read (0x60);
- debug ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
- reg |= 0x10;
- reg &= ~0x08;
- pic_write (0x60, reg);
-#ifdef DEBUG
- reg = pic_read (0x60);
- printf ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
-#endif
- udelay(10000);
-
- return (0);
-}
-#endif
-
-
-int pcmcia_voltage_set(int slot, int vcc, int vpp)
-{
- volatile pcmconf8xx_t *pcmp;
- u_long reg;
- uchar val;
-
- debug ("voltage_set: "
- PCMCIA_BOARD_MSG
- " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
- 'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
-
- pcmp = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
- /*
- * Disable PCMCIA buffers (isolate the interface)
- * and assert RESET signal
- */
- debug ("Disable PCMCIA buffers and assert RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg |= __MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg |= __MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- /*
- * Turn off all power (switch to high impedance)
- */
- debug ("PCMCIA power OFF\n");
- val = MAX1604_VCCBHIZ | MAX1604_VPPBHIZ;
- i2c_set_bus_num(0);
- i2c_write (CONFIG_SYS_I2C_POWER_A_ADDR, 0, 0, &val, 1);
-
- val = 0;
- switch(vcc) {
- case 0: break;
- case 33: val = MAX1604_VCC_35; break;
- case 50: break;
- default: goto done;
- }
-
- /* Checking supported voltages */
-
- debug ("PIPR: 0x%x --> %s\n",
- pcmp->pcmc_pipr,
- (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
-
- i2c_write (CONFIG_SYS_I2C_POWER_A_ADDR, 0, 0, &val, 1);
- if (val) {
- debug ("PCMCIA powered at %sV\n",
- (val & MAX1604_VCC_35) ? "3.3" : "5.0");
- } else {
- debug ("PCMCIA powered down\n");
- }
-
-done:
- debug ("Enable PCMCIA buffers and stop RESET\n");
- reg = PCMCIA_PGCRX(_slot_);
- reg &= ~__MY_PCMCIA_GCRX_CXRESET; /* active high */
- reg &= ~__MY_PCMCIA_GCRX_CXOE; /* active low */
- PCMCIA_PGCRX(_slot_) = reg;
- udelay(500);
-
- debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
- slot+'A');
- return (0);
-}
-
-#endif /* CONFIG_PCMCIA */
+++ /dev/null
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-OUTPUT_ARCH(powerpc)
-/* Do we need any of these for elf?
- __DYNAMIC = 0; */
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .interp : { *(.interp) }
- .hash : { *(.hash) }
- .dynsym : { *(.dynsym) }
- .dynstr : { *(.dynstr) }
- .rel.text : { *(.rel.text) }
- .rela.text : { *(.rela.text) }
- .rel.data : { *(.rel.data) }
- .rela.data : { *(.rela.data) }
- .rel.rodata : { *(.rel.rodata) }
- .rela.rodata : { *(.rela.rodata) }
- .rel.got : { *(.rel.got) }
- .rela.got : { *(.rela.got) }
- .rel.ctors : { *(.rel.ctors) }
- .rela.ctors : { *(.rela.ctors) }
- .rel.dtors : { *(.rel.dtors) }
- .rela.dtors : { *(.rela.dtors) }
- .rel.bss : { *(.rel.bss) }
- .rela.bss : { *(.rela.bss) }
- .rel.plt : { *(.rel.plt) }
- .rela.plt : { *(.rela.plt) }
- .init : { *(.init) }
- .plt : { *(.plt) }
- .text :
- {
- /* WARNING - the following is hand-optimized to fit within */
- /* the sector layout of our flash chips! XXX FIXME XXX */
-
- arch/powerpc/cpu/mpc8xx/start.o (.text)
- common/dlmalloc.o (.text)
- lib/vsprintf.o (.text)
- lib/crc32.o (.text)
- arch/powerpc/lib/extable.o (.text)
-
- . = env_offset;
- common/env_embedded.o(.text)
-
- *(.text)
- *(.got1)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(.rodata)
- *(.rodata1)
- *(.rodata.str1.4)
- *(.eh_frame)
- }
- .fini : { *(.fini) } =0
- .ctors : { *(.ctors) }
- .dtors : { *(.dtors) }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x0FFF) & 0xFFFFF000;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- *(.got)
- _GOT2_TABLE_ = .;
- *(.got2)
- _FIXUP_TABLE_ = .;
- *(.fixup)
- }
- __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data)
- *(.data1)
- *(.sdata)
- *(.sdata2)
- *(.dynamic)
- CONSTRUCTORS
- }
- _edata = .;
- PROVIDE (edata = .);
-
-
- . = ALIGN(4);
- .u_boot_list : {
- KEEP(*(SORT(.u_boot_list*)));
- }
-
-
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(4096);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(4096);
- __init_end = .;
-
- __bss_start = .;
- .bss :
- {
- *(.sbss) *(.scommon)
- *(.dynbss)
- *(.bss)
- *(COMMON)
- }
- __bss_end = . ;
- PROVIDE (end = .);
-}
+++ /dev/null
-CONFIG_PPC=y
-CONFIG_8xx=y
-CONFIG_TARGET_LWMON=y
Board Arch CPU Commit Removed Last known maintainer/contact
=================================================================================================
+lwmon powerpc mpc8xx - - Wolfgang Denk <wd@denx.de>
NETVIA powerpc mpc8xx - - Pantelis Antoniou <panto@intracom.gr>
R360MPI powerpc mpc8xx - - Wolfgang Denk <wd@denx.de>
RRvision powerpc mpc8xx - - Wolfgang Denk <wd@denx.de>
/* -------------------------------------------------------------------- */
-#if defined(CONFIG_LWMON)
-#define CONFIG_SYS_PCMCIA_TIMING ( PCMCIA_SHT(9) \
- | PCMCIA_SST(3) \
- | PCMCIA_SL(12))
-#else
#define CONFIG_SYS_PCMCIA_TIMING ( PCMCIA_SHT(2) \
| PCMCIA_SST(4) \
| PCMCIA_SL(9))
-#endif
/* -------------------------------------------------------------------- */
/* Enable the LCD panel */
immr->im_siu_conf.sc_sdcr |= (1 << (31 - 25)); /* LAM = 1 */
lcdp->lcd_lccr |= LCCR_PON;
-
-#if defined(CONFIG_LWMON)
- { uchar c = pic_read (0x60);
-#if defined(CONFIG_LCD) && defined(CONFIG_LWMON) && (CONFIG_POST & CONFIG_SYS_POST_SYSMON)
- /* Enable LCD later in sysmon test, only if temperature is OK */
-#else
- c |= 0x07; /* Power on CCFL, Enable CCFL, Chip Enable LCD */
-#endif
- pic_write (0x60, c);
- }
-#endif /* CONFIG_LWMON */
}
/************************************************************************/
*/
#define TEST_FLASH_ADDR 0x40100000
-/* Define GPIO ports to signal start of burst transfers and errors */
-#ifdef CONFIG_LWMON
-/* Use PD.8 to signal start of burst transfers */
-#define GPIO1_DAT (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat)
-#define GPIO1_BIT 0x0080
-/* Configure PD.8 as general purpose output */
-#define GPIO1_INIT \
- ((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pdpar &= ~GPIO1_BIT; \
- ((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddir |= GPIO1_BIT;
-/* Use PD.9 to signal error */
-#define GPIO2_DAT (((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat)
-#define GPIO2_BIT 0x0040
-/* Configure PD.9 as general purpose output */
-#define GPIO2_INIT \
- ((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pdpar &= ~GPIO2_BIT; \
- ((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddir |= GPIO2_BIT;
-#endif /* CONFIG_LWMON */
-
-
static void test_prepare (void);
static int test_burst_start (unsigned long size, unsigned long pattern);
static void test_map_8M (unsigned long paddr, unsigned long vaddr, int cached);
#endif
int eeprom_read (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt);
int eeprom_write (unsigned dev_addr, unsigned offset, uchar *buffer, unsigned cnt);
-#ifdef CONFIG_LWMON
-extern uchar pic_read (uchar reg);
-extern void pic_write (uchar reg, uchar val);
-#endif
/*
* Set this up regardless of board
#endif /* CONFIG_IVMS8, CONFIG_IVML24 */
-/*** LWMON **********************************************************/
-
-#if defined(CONFIG_LWMON)
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
- */
-#define PROFF_ENET PROFF_SCC2
-#define CPM_CR_ENET CPM_CR_CH_SCC2
-#define SCC_ENET 1
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0800) /* PA 4 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK4) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00003E00)
-#endif /* CONFIG_LWMON */
-
/*** KM8XX *********************************************************/
/* The KM8XX Service Module uses SCC3 for Ethernet */
+++ /dev/null
-/*
- * (C) Copyright 2001-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* External logbuffer support */
-#define CONFIG_LOGBUFFER
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC823 1 /* This is a MPC823E CPU */
-#define CONFIG_LWMON 1 /* ...on a LWMON board */
-
-#define CONFIG_SYS_TEXT_BASE 0x40000000
-
-/* Default Ethernet MAC address */
-#define CONFIG_ETHADDR 00:11:B0:00:00:00
-
-/* The default Ethernet MAC address can be overwritten just once */
-#ifdef CONFIG_ETHADDR
-#define CONFIG_OVERWRITE_ETHADDR_ONCE 1
-#endif
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f() */
-#define CONFIG_BOARD_POSTCLK_INIT 1 /* Call board_postclk_init() */
-#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r() */
-
-#define CONFIG_LCD 1 /* use LCD controller ... */
-#define CONFIG_MPC8XX_LCD
-#define CONFIG_HLD1045 1 /* ... with a HLD1045 display */
-
-#define CONFIG_LCD_LOGO 1 /* print our logo on the LCD */
-#define CONFIG_LCD_INFO 1 /* ... and some board info */
-#define CONFIG_SPLASH_SCREEN /* ... with splashscreen support*/
-
-#define CONFIG_8xx_CONS_SMC2 1 /* Console is on SMC2 */
-#define CONFIG_8xx_CONS_SCC2 1 /* Console is on SCC2 */
-
-#define CONFIG_BAUDRATE 115200 /* with watchdog >= 38400 needed */
-
-#define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */
-
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
-
-/* pre-boot commands */
-#define CONFIG_PREBOOT "setenv bootdelay 15"
-
-#undef CONFIG_BOOTARGS
-
-/* POST support */
-#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \
- CONFIG_SYS_POST_WATCHDOG | \
- CONFIG_SYS_POST_RTC | \
- CONFIG_SYS_POST_MEMORY | \
- CONFIG_SYS_POST_CPU | \
- CONFIG_SYS_POST_UART | \
- CONFIG_SYS_POST_ETHER | \
- CONFIG_SYS_POST_I2C | \
- CONFIG_SYS_POST_SPI | \
- CONFIG_SYS_POST_USB | \
- CONFIG_SYS_POST_SPR | \
- CONFIG_SYS_POST_SYSMON)
-
-/*
- * Keyboard commands:
- * # = 0x28 = ENTER : enable bootmessages on LCD
- * 2 = 0x3A+0x3C = F1 + F3 : enable update mode
- * 3 = 0x3C+0x3F = F3 + F6 : enable test mode
- */
-
-#define CONFIG_BOOTCOMMAND "source 40040000;saveenv"
-
-/* "gatewayip=10.8.211.250\0" \ */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "kernel_addr=40080000\0" \
- "ramdisk_addr=40280000\0" \
- "netmask=255.255.192.0\0" \
- "serverip=10.8.2.101\0" \
- "ipaddr=10.8.57.0\0" \
- "magic_keys=#23\0" \
- "key_magic#=28\0" \
- "key_cmd#=setenv addfb setenv 'bootargs $bootargs console=tty0'\0" \
- "key_magic2=3A+3C\0" \
- "key_cmd2=echo *** Entering Update Mode ***;" \
- "if fatload ide 0:3 10000 update.scr;" \
- "then source 10000;" \
- "else echo *** UPDATE FAILED ***;" \
- "fi\0" \
- "key_magic3=3C+3F\0" \
- "key_cmd3=echo *** Entering Test Mode ***;" \
- "setenv add_misc 'setenv bootargs $bootargs testmode'\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addfb=setenv bootargs $bootargs console=ttyS1,$baudrate\0" \
- "addip=setenv bootargs $bootargs " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off " \
- "panic=1\0" \
- "add_wdt=setenv bootargs $bootargs $wdt_args\0" \
- "add_misc=setenv bootargs $bootargs runmode\0" \
- "flash_nfs=run nfsargs addip add_wdt addfb add_misc;" \
- "bootm $kernel_addr\0" \
- "flash_self=run ramargs addip add_wdt addfb add_misc;" \
- "bootm $kernel_addr $ramdisk_addr\0" \
- "net_nfs=tftp 100000 /tftpboot/uImage.lwmon;" \
- "run nfsargs addip add_wdt addfb;bootm\0" \
- "rootpath=/opt/eldk/ppc_8xx\0" \
- "load=tftp 100000 /tftpboot/u-boot.bin\0" \
- "update=protect off 1:0;era 1:0;cp.b 100000 40000000 $filesize\0" \
- "wdt_args=wdt_8xx=off\0" \
- "verify=no"
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-
-#define CONFIG_WATCHDOG 1 /* watchdog enabled */
-#define CONFIG_SYS_WATCHDOG_FREQ (CONFIG_SYS_HZ / 20)
-
-#undef CONFIG_STATUS_LED /* Status LED disabled */
-
-/* enable I2C and select the hardware/software driver */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED 93000 /* 93 kHz is supposed to work */
-#define CONFIG_SYS_I2C_SOFT_SLAVE 0xFE
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#define PB_SCL 0x00000020 /* PB 26 */
-#define PB_SDA 0x00000010 /* PB 27 */
-
-#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
-#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
-#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
-#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
-#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
- else immr->im_cpm.cp_pbdat &= ~PB_SDA
-#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
- else immr->im_cpm.cp_pbdat &= ~PB_SCL
-#define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */
-
-
-#define CONFIG_RTC_PCF8563 /* use Philips PCF8563 RTC */
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_BMP
-#define CONFIG_CMD_BSP
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-
-#ifdef CONFIG_POST
-#define CONFIG_CMD_DIAG
-#endif
-
-
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */
-
-#define CONFIG_SYS_PIO_MODE 0 /* IDE interface in PIO Mode 0 */
-
-/*
- * When the watchdog is enabled, output must be fast enough in Linux.
- */
-#ifdef CONFIG_WATCHDOG
-#define CONFIG_SYS_BAUDRATE_TABLE { 38400, 57600, 115200 }
-#endif
-
-/*----------------------------------------------------------------------*/
-#define CONFIG_MODEM_SUPPORT 1 /* enable modem initialization stuff */
-#undef CONFIG_MODEM_SUPPORT_DEBUG
-
-#define CONFIG_MODEM_KEY_MAGIC "3C+3D" /* press F3 + F4 keys to enable modem */
-#define CONFIG_POST_KEY_MAGIC "3C+3E" /* press F3 + F5 keys to force POST */
-#if 0
-#define CONFIG_AUTOBOOT_KEYED /* Enable "password" protection */
-#define CONFIG_AUTOBOOT_PROMPT \
- "\nEnter password - autoboot in %d sec...\n", bootdelay
-#define CONFIG_AUTOBOOT_DELAY_STR " " /* "password" */
-#endif
-/*----------------------------------------------------------------------*/
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x40000000
-#if defined(DEBUG) || defined(CONFIG_CMD_IDE)
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#else
-#define CONFIG_SYS_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */
-#endif
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 180000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 600 /* Timeout for Flash Write (in ms) */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-#define CONFIG_SYS_FLASH_BUFFER_WRITE_TOUT 2048 /* Timeout for Flash Buffer Write (in ms) */
-/* Buffer size.
- We have two flash devices connected in parallel.
- Each device incorporates a Write Buffer of 32 bytes.
- */
-#define CONFIG_SYS_FLASH_BUFFER_SIZE (2*32)
-
-/* Put environment in flash which is much faster to boot than using the EEPROM */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR 0x40040000 /* Address of Environment Sector */
-#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment */
-#define CONFIG_ENV_SECT_SIZE 0x40000 /* we have BIG sectors only :-( */
-
-/*-----------------------------------------------------------------------
- * I2C/EEPROM Configuration
- */
-
-#define CONFIG_SYS_I2C_AUDIO_ADDR 0x28 /* Audio volume control */
-#define CONFIG_SYS_I2C_SYSMON_ADDR 0x2E /* LM87 System Monitor */
-#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* PCF8563 RTC */
-#define CONFIG_SYS_I2C_POWER_A_ADDR 0x52 /* PCMCIA/USB power switch, channel A */
-#define CONFIG_SYS_I2C_POWER_B_ADDR 0x53 /* PCMCIA/USB power switch, channel B */
-#define CONFIG_SYS_I2C_KEYBD_ADDR 0x56 /* PIC LWE keyboard */
-#define CONFIG_SYS_I2C_PICIO_ADDR 0x57 /* PIC IO Expander */
-
-#undef CONFIG_USE_FRAM /* Use FRAM instead of EEPROM */
-
-#ifdef CONFIG_USE_FRAM /* use FRAM */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x55 /* FRAM FM24CL64 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#else /* use EEPROM */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x58 /* EEPROM AT24C164 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* takes up to 10 msec */
-#endif /* CONFIG_USE_FRAM */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
-
-/* List of I2C addresses to be verified by POST */
-#ifdef CONFIG_USE_FRAM
-#define CONFIG_SYS_POST_I2C_ADDRS {/* CONFIG_SYS_I2C_AUDIO_ADDR, */ \
- CONFIG_SYS_I2C_SYSMON_ADDR, \
- CONFIG_SYS_I2C_RTC_ADDR, \
- CONFIG_SYS_I2C_POWER_A_ADDR, \
- CONFIG_SYS_I2C_POWER_B_ADDR, \
- CONFIG_SYS_I2C_KEYBD_ADDR, \
- CONFIG_SYS_I2C_PICIO_ADDR, \
- CONFIG_SYS_I2C_EEPROM_ADDR, \
- }
-#else /* Use EEPROM - which show up on 8 consequtive addresses */
-#define CONFIG_SYS_POST_I2C_ADDRS {/* CONFIG_SYS_I2C_AUDIO_ADDR, */ \
- CONFIG_SYS_I2C_SYSMON_ADDR, \
- CONFIG_SYS_I2C_RTC_ADDR, \
- CONFIG_SYS_I2C_POWER_A_ADDR, \
- CONFIG_SYS_I2C_POWER_B_ADDR, \
- CONFIG_SYS_I2C_KEYBD_ADDR, \
- CONFIG_SYS_I2C_PICIO_ADDR, \
- CONFIG_SYS_I2C_EEPROM_ADDR+0, \
- CONFIG_SYS_I2C_EEPROM_ADDR+1, \
- CONFIG_SYS_I2C_EEPROM_ADDR+2, \
- CONFIG_SYS_I2C_EEPROM_ADDR+3, \
- CONFIG_SYS_I2C_EEPROM_ADDR+4, \
- CONFIG_SYS_I2C_EEPROM_ADDR+5, \
- CONFIG_SYS_I2C_EEPROM_ADDR+6, \
- CONFIG_SYS_I2C_EEPROM_ADDR+7, \
- }
-#endif /* CONFIG_USE_FRAM */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if 0 && defined(CONFIG_WATCHDOG) /* LWMON uses external MAX706TESA WD */
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- * PCMCIA config., multi-function pin tri-state
- */
-/* EARB, DBGC and DBPC are initialised by the HCW */
-/* => 0x000000C0 */
-#define CONFIG_SYS_SIUMCR (SIUMCR_GB5E)
-/*#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) */
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit, set PLL multiplication factor !
- */
-/* 0x00405000 */
-#define CONFIG_SYS_PLPRCR_MF 4 /* (4+1) * 13.2 = 66 MHz Clock */
-#define CONFIG_SYS_PLPRCR \
- ( (CONFIG_SYS_PLPRCR_MF << PLPRCR_MF_SHIFT) | \
- PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | \
- /*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \
- PLPRCR_CSR /*| PLPRCR_LOLRE|PLPRCR_FIOPD*/ \
- )
-
-#define CONFIG_8xx_GCLK_FREQ ((CONFIG_SYS_PLPRCR_MF+1)*13200000)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-/* 0x01800000 */
-#define CONFIG_SYS_SCCR (SCCR_COM00 | /*SCCR_TBS|*/ \
- SCCR_RTDIV | SCCR_RTSEL | \
- /*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \
- SCCR_EBDF00 | SCCR_DFSYNC00 | \
- SCCR_DFBRG00 | SCCR_DFNL000 | \
- SCCR_DFNH000 | SCCR_DFLCD100 | \
- SCCR_DFALCD01)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register 11-27
- *-----------------------------------------------------------------------
- */
-/* 0x00C3 => 0x0003 */
-#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration Register 19-4
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RCCR 0x0000
-
-/*-----------------------------------------------------------------------
- * RMDS - RISC Microcode Development Support Control Register
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RMDS 0
-
-/*-----------------------------------------------------------------------
- *
- * Interrupt Levels
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_CPM_INTERRUPT 13 /* SIU_LEVEL6 */
-
-/*-----------------------------------------------------------------------
- * PCMCIA stuff
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_PCMCIA_MEM_ADDR (0x50000000)
-#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_DMA_ADDR (0x54000000)
-#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0x58000000)
-#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
-#define CONFIG_SYS_PCMCIA_IO_ADDR (0x5C000000)
-#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-#undef CONFIG_IDE_RESET /* reset for ide not supported */
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
-
-/* Offset for data I/O */
-#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for normal register accesses */
-#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
-
-/* Offset for alternate registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
-
-#define CONFIG_SUPPORT_VFAT /* enable VFAT support */
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH) - second Flash bank optional
- */
-
-#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0x41000000 /* FLASH bank #1 */
-
-/* used to re-map FLASH:
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-#define CONFIG_SYS_REMAP_OR_AM 0xFF000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xFF000000 /* OR addr mask */
-
-/* FLASH timing: ACS = 00, TRLX = 0, CSNT = 1, SCY = 8, EHTR = 0 */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_SCY_8_CLK)
-
-#define CONFIG_SYS_OR0_REMAP ( CONFIG_SYS_REMAP_OR_AM | OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \
- CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | OR_ACS_DIV1 | OR_BI | \
- CONFIG_SYS_OR_TIMING_FLASH)
-/* 16 bit, bank valid */
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_32 | BR_V )
-
-#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
-#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
-#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_PS_32 | BR_V )
-
-/*
- * BR3/OR3: SDRAM
- *
- * Multiplexed addresses, GPL5 output to GPL5_A (don't care)
- */
-#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank */
-#define SDRAM_PRELIM_OR_AM 0xF0000000 /* map 256 MB (>SDRAM_MAX_SIZE!) */
-#define SDRAM_TIMING OR_SCY_0_CLK /* SDRAM-Timing */
-
-#define SDRAM_MAX_SIZE 0x08000000 /* max 128 MB SDRAM */
-
-#define CONFIG_SYS_OR3_PRELIM (SDRAM_PRELIM_OR_AM | OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING )
-#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-/*
- * BR5/OR5: Touch Panel
- *
- * AM=0xFFC00 ATM=0 CSNT/SAM=0 ACS/G5LA/G5LS=3 BIH=1 SCY=0 SETA=0 TRLX=0 EHTR=0
- */
-#define TOUCHPNL_BASE 0x20000000
-#define TOUCHPNL_OR_AM 0xFFFF8000
-#define TOUCHPNL_TIMING OR_SCY_0_CLK
-
-#define CONFIG_SYS_OR5_PRELIM (TOUCHPNL_OR_AM | OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \
- TOUCHPNL_TIMING )
-#define CONFIG_SYS_BR5_PRELIM ((TOUCHPNL_BASE & BR_BA_MSK) | BR_PS_32 | BR_V )
-
-#define CONFIG_SYS_MEMORY_75
-#undef CONFIG_SYS_MEMORY_7E
-#undef CONFIG_SYS_MEMORY_8E
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MPTPR 0x200
-
-/*
- * MAMR settings for SDRAM
- */
-
-#define CONFIG_SYS_MAMR_8COL 0x80802114
-#define CONFIG_SYS_MAMR_9COL 0x80904114
-
-/*
- * MAR setting for SDRAM
- */
-#define CONFIG_SYS_MAR 0x00000088
-
-#endif /* __CONFIG_H */
# define CONFIG_PCMCIA_SLOT_B /* The TQM8xxL use SLOT_B */
#elif defined(CONFIG_IVMS8) || defined(CONFIG_IVML24) /* The IVM* use SLOT_A */
# define CONFIG_PCMCIA_SLOT_A
-#elif defined(CONFIG_LWMON) /* The LWMON use SLOT_B */
-# define CONFIG_PCMCIA_SLOT_B
#elif defined(CONFIG_ATC) /* The ATC use SLOT_A */
# define CONFIG_PCMCIA_SLOT_A
#else
projects / u-boot / commitdiff