config ARM64
bool
select PHYS_64BIT
+ select SYS_CACHE_SHIFT_6
config DMA_ADDR_T_64BIT
bool
default y if ARM64
config HAS_VBAR
- bool
+ bool
config HAS_THUMB2
- bool
+ bool
config CPU_ARM720T
- bool
+ bool
+ select SYS_CACHE_SHIFT_5
config CPU_ARM920T
- bool
+ bool
+ select SYS_CACHE_SHIFT_5
config CPU_ARM926EJS
- bool
+ bool
+ select SYS_CACHE_SHIFT_5
config CPU_ARM946ES
- bool
+ bool
+ select SYS_CACHE_SHIFT_5
config CPU_ARM1136
- bool
+ bool
+ select SYS_CACHE_SHIFT_5
config CPU_ARM1176
- bool
- select HAS_VBAR
+ bool
+ select HAS_VBAR
+ select SYS_CACHE_SHIFT_5
config CPU_V7
- bool
- select HAS_VBAR
- select HAS_THUMB2
+ bool
+ select HAS_VBAR
+ select HAS_THUMB2
+ select SYS_CACHE_SHIFT_6
config CPU_V7M
bool
- select HAS_THUMB2
+ select HAS_THUMB2
+ select SYS_CACHE_SHIFT_5
config CPU_PXA
- bool
+ bool
+ select SYS_CACHE_SHIFT_5
config CPU_SA1100
- bool
+ bool
+ select SYS_CACHE_SHIFT_5
config SYS_CPU
- default "arm720t" if CPU_ARM720T
- default "arm920t" if CPU_ARM920T
- default "arm926ejs" if CPU_ARM926EJS
- default "arm946es" if CPU_ARM946ES
- default "arm1136" if CPU_ARM1136
- default "arm1176" if CPU_ARM1176
- default "armv7" if CPU_V7
- default "armv7m" if CPU_V7M
- default "pxa" if CPU_PXA
- default "sa1100" if CPU_SA1100
+ default "arm720t" if CPU_ARM720T
+ default "arm920t" if CPU_ARM920T
+ default "arm926ejs" if CPU_ARM926EJS
+ default "arm946es" if CPU_ARM946ES
+ default "arm1136" if CPU_ARM1136
+ default "arm1176" if CPU_ARM1176
+ default "armv7" if CPU_V7
+ default "armv7m" if CPU_V7M
+ default "pxa" if CPU_PXA
+ default "sa1100" if CPU_SA1100
default "armv8" if ARM64
config SYS_ARM_ARCH
default 4 if CPU_SA1100
default 8 if ARM64
+config SYS_CACHE_SHIFT_5
+ bool
+
+config SYS_CACHE_SHIFT_6
+ bool
+
+config SYS_CACHE_SHIFT_7
+ bool
+
+config SYS_CACHELINE_SIZE
+ int
+ default 128 if SYS_CACHE_SHIFT_7
+ default 64 if SYS_CACHE_SHIFT_6
+ default 32 if SYS_CACHE_SHIFT_5
+
config SEMIHOSTING
bool "support boot from semihosting"
help
select DM_GPIO
config TARGET_ETAMIN
- bool "Support etamin"
- select CPU_V7
- select SUPPORT_SPL
+ bool "Support etamin"
+ select CPU_V7
+ select SUPPORT_SPL
select DM
select DM_SERIAL
select DM_GPIO
bool "Support ThunderX 88xx"
select ARM64
select OF_CONTROL
+ select SYS_CACHE_SHIFT_7
endchoice
}
#ifndef CONFIG_SYS_DCACHE_OFF
-
-#ifndef CONFIG_SYS_CACHELINE_SIZE
-#define CONFIG_SYS_CACHELINE_SIZE 32
-#endif
-
void invalidate_dcache_all(void)
{
asm volatile("mcr p15, 0, %0, c7, c6, 0" : : "r" (0));
#include <common.h>
#ifndef CONFIG_SYS_DCACHE_OFF
-
-#ifndef CONFIG_SYS_CACHELINE_SIZE
-#define CONFIG_SYS_CACHELINE_SIZE 32
-#endif
-
void invalidate_dcache_all(void)
{
asm volatile("mcr p15, 0, %0, c7, c6, 0\n" : : "r"(0));
#include <common.h>
#ifndef CONFIG_SYS_DCACHE_OFF
-
-#ifndef CONFIG_SYS_CACHELINE_SIZE
-#define CONFIG_SYS_CACHELINE_SIZE 32
-#endif
-
void invalidate_dcache_all(void)
{
/* Flush/Invalidate I cache */
sun5i-a13-ampe-a76.dtb \
sun5i-a13-difrnce-dit4350.dtb \
sun5i-a13-empire-electronix-d709.dtb \
+ sun5i-a13-empire-electronix-m712.dtb \
sun5i-a13-hsg-h702.dtb \
sun5i-a13-inet-86vs.dtb \
sun5i-a13-inet-98v-rev2.dtb \
sun6i-a31-mixtile-loftq.dtb \
sun6i-a31s-colorfly-e708-q1.dtb \
sun6i-a31s-cs908.dtb \
+ sun6i-a31s-inet-q972.dtb \
sun6i-a31s-primo81.dtb \
sun6i-a31s-sina31s.dtb \
sun6i-a31s-sinovoip-bpi-m2.dtb \
dtb-$(CONFIG_MACH_SUN7I) += \
sun7i-a20-ainol-aw1.dtb \
sun7i-a20-bananapi.dtb \
+ sun7i-a20-bananapi-m1-plus.dtb \
sun7i-a20-bananapro.dtb \
sun7i-a20-cubieboard2.dtb \
sun7i-a20-cubietruck.dtb \
sun7i-a20-olimex-som-evb.dtb \
sun7i-a20-olinuxino-lime.dtb \
sun7i-a20-olinuxino-lime2.dtb \
+ sun7i-a20-olinuxino-lime2-emmc.dtb \
sun7i-a20-olinuxino-micro.dtb \
sun7i-a20-orangepi.dtb \
sun7i-a20-orangepi-mini.dtb \
sun8i-a83t-cubietruck-plus.dtb \
sun8i-a83t-sinovoip-bpi-m3.dtb
dtb-$(CONFIG_MACH_SUN8I_H3) += \
+ sun8i-h3-bananapi-m2-plus.dtb \
sun8i-h3-orangepi-2.dtb \
sun8i-h3-orangepi-lite.dtb \
sun8i-h3-orangepi-one.dtb \
reg_ldo5: ldo5 {
regulator-name = "ldo5";
+ status = "disabled";
};
};
--- /dev/null
+/*
+ * Copyright 2015 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/*
+ * AXP809 Integrated Power Management Chip
+ */
+
+&axp809 {
+ compatible = "x-powers,axp809";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+};
};
blue {
- label = "a1000:blue:usr";
+ label = "a1000:blue:pwr";
gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
};
};
regulator-name = "emac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
+ startup-delay-us = <20000>;
enable-active-high;
gpio = <&pio 7 15 GPIO_ACTIVE_HIGH>;
};
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "On-board SPDIF";
+
+ simple-audio-card,cpu {
+ sound-dai = <&spdif>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&spdif_out>;
+ };
+ };
+
+ spdif_out: spdif-out {
+ #sound-dai-cells = <0>;
+ compatible = "linux,spdif-dit";
+ };
};
&ahci {
status = "okay";
};
+&spdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spdif_tx_pins_a>;
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
regulator-name = "emac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
+ startup-delay-us = <20000>;
enable-active-high;
gpio = <&pio 7 19 GPIO_ACTIVE_HIGH>;
};
status = "okay";
};
+&otg_sram {
+ status = "okay";
+};
+
+&pio {
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PH4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
+ allwinner,pins = "PH5";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ };
+};
+
+®_usb0_vbus {
+ status = "okay";
+};
+
®_usb2_vbus {
gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
status = "okay";
allwinner,pins = "PH6";
};
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
+ usb0_vbus-supply = <®_usb0_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
};
regulator-name = "emac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
+ startup-delay-us = <20000>;
enable-active-high;
gpio = <&pio 7 19 GPIO_ACTIVE_HIGH>; /* PH19 */
};
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-hdmi";
- clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>,
- <&ahb_gates 44>, <&dram_gates 26>;
+ clocks = <&ahb_gates 36>, <&ahb_gates 43>,
+ <&ahb_gates 44>, <&de_be0_clk>,
+ <&tcon0_ch1_clk>, <&dram_gates 26>;
status = "disabled";
};
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_fe0-de_be0-lcd0-hdmi";
- clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>,
+ clocks = <&ahb_gates 36>, <&ahb_gates 43>,
<&ahb_gates 44>, <&ahb_gates 46>,
+ <&de_be0_clk>, <&de_fe0_clk>, <&tcon0_ch1_clk>,
<&dram_gates 25>, <&dram_gates 26>;
status = "disabled";
};
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_fe0-de_be0-lcd0";
- clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 44>,
- <&ahb_gates 46>, <&dram_gates 25>,
- <&dram_gates 26>;
+ clocks = <&ahb_gates 36>, <&ahb_gates 44>, <&ahb_gates 46>,
+ <&de_be0_clk>, <&de_fe0_clk>, <&tcon0_ch0_clk>,
+ <&dram_gates 25>, <&dram_gates 26>;
status = "disabled";
};
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_fe0-de_be0-lcd0-tve0";
- clocks = <&pll5 1>, <&ahb_gates 34>, <&ahb_gates 36>,
+ clocks = <&ahb_gates 34>, <&ahb_gates 36>,
<&ahb_gates 44>, <&ahb_gates 46>,
+ <&de_be0_clk>, <&de_fe0_clk>,
+ <&tcon0_ch1_clk>, <&dram_gates 5>,
<&dram_gates 25>, <&dram_gates 26>;
status = "disabled";
};
clock-output-names = "osc24M";
};
+ osc3M: osc3M_clk {
+ compatible = "fixed-factor-clock";
+ #clock-cells = <0>;
+ clock-div = <8>;
+ clock-mult = <1>;
+ clocks = <&osc24M>;
+ clock-output-names = "osc3M";
+ };
+
osc32k: clk@0 {
#clock-cells = <0>;
compatible = "fixed-clock";
"pll2-4x", "pll2-8x";
};
+ pll3: clk@01c20010 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-pll3-clk";
+ reg = <0x01c20010 0x4>;
+ clocks = <&osc3M>;
+ clock-output-names = "pll3";
+ };
+
+ pll3x2: pll3x2_clk {
+ compatible = "fixed-factor-clock";
+ #clock-cells = <0>;
+ clock-div = <1>;
+ clock-mult = <2>;
+ clocks = <&pll3>;
+ clock-output-names = "pll3-2x";
+ };
+
pll4: clk@01c20018 {
#clock-cells = <0>;
compatible = "allwinner,sun4i-a10-pll1-clk";
clock-output-names = "pll6_sata", "pll6_other", "pll6";
};
+ pll7: clk@01c20030 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-pll3-clk";
+ reg = <0x01c20030 0x4>;
+ clocks = <&osc3M>;
+ clock-output-names = "pll7";
+ };
+
+ pll7x2: pll7x2_clk {
+ compatible = "fixed-factor-clock";
+ #clock-cells = <0>;
+ clock-div = <1>;
+ clock-mult = <2>;
+ clocks = <&pll7>;
+ clock-output-names = "pll7-2x";
+ };
+
/* dummy is 200M */
cpu: cpu@01c20054 {
#clock-cells = <0>;
clock-output-names = "ir1";
};
+ spdif_clk: clk@01c200c0 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod1-clk";
+ reg = <0x01c200c0 0x4>;
+ clocks = <&pll2 SUN4I_A10_PLL2_8X>,
+ <&pll2 SUN4I_A10_PLL2_4X>,
+ <&pll2 SUN4I_A10_PLL2_2X>,
+ <&pll2 SUN4I_A10_PLL2_1X>;
+ clock-output-names = "spdif";
+ };
+
usb_clk: clk@01c200cc {
#clock-cells = <1>;
#reset-cells = <1>;
"dram_de_mp", "dram_ace";
};
+ de_be0_clk: clk@01c20104 {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-display-clk";
+ reg = <0x01c20104 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll5 1>;
+ clock-output-names = "de-be0";
+ };
+
+ de_be1_clk: clk@01c20108 {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-display-clk";
+ reg = <0x01c20108 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll5 1>;
+ clock-output-names = "de-be1";
+ };
+
+ de_fe0_clk: clk@01c2010c {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-display-clk";
+ reg = <0x01c2010c 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll5 1>;
+ clock-output-names = "de-fe0";
+ };
+
+ de_fe1_clk: clk@01c20110 {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-display-clk";
+ reg = <0x01c20110 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll5 1>;
+ clock-output-names = "de-fe1";
+ };
+
+
+ tcon0_ch0_clk: clk@01c20118 {
+ #clock-cells = <0>;
+ #reset-cells = <1>;
+ compatible = "allwinner,sun4i-a10-tcon-ch0-clk";
+ reg = <0x01c20118 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+ clock-output-names = "tcon0-ch0-sclk";
+
+ };
+
+ tcon1_ch0_clk: clk@01c2011c {
+ #clock-cells = <0>;
+ #reset-cells = <1>;
+ compatible = "allwinner,sun4i-a10-tcon-ch1-clk";
+ reg = <0x01c2011c 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+ clock-output-names = "tcon1-ch0-sclk";
+
+ };
+
+ tcon0_ch1_clk: clk@01c2012c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-tcon-ch0-clk";
+ reg = <0x01c2012c 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+ clock-output-names = "tcon0-ch1-sclk";
+
+ };
+
+ tcon1_ch1_clk: clk@01c20130 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-tcon-ch1-clk";
+ reg = <0x01c20130 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+ clock-output-names = "tcon1-ch1-sclk";
+
+ };
+
ve_clk: clk@01c2013c {
#clock-cells = <0>;
#reset-cells = <0>;
#dma-cells = <2>;
};
+ nfc: nand@01c03000 {
+ compatible = "allwinner,sun4i-a10-nand";
+ reg = <0x01c03000 0x1000>;
+ interrupts = <37>;
+ clocks = <&ahb_gates 13>, <&nand_clk>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma SUN4I_DMA_DEDICATED 3>;
+ dma-names = "rxtx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
spi0: spi@01c05000 {
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c05000 0x1000>;
#interrupt-cells = <3>;
#gpio-cells = <3>;
- pwm0_pins_a: pwm0@0 {
- allwinner,pins = "PB2";
- allwinner,function = "pwm";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- pwm1_pins_a: pwm1@0 {
- allwinner,pins = "PI3";
- allwinner,function = "pwm";
+ emac_pins_a: emac0@0 {
+ allwinner,pins = "PA0", "PA1", "PA2",
+ "PA3", "PA4", "PA5", "PA6",
+ "PA7", "PA8", "PA9", "PA10",
+ "PA11", "PA12", "PA13", "PA14",
+ "PA15", "PA16";
+ allwinner,function = "emac";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart0_pins_a: uart0@0 {
- allwinner,pins = "PB22", "PB23";
- allwinner,function = "uart0";
+ i2c0_pins_a: i2c0@0 {
+ allwinner,pins = "PB0", "PB1";
+ allwinner,function = "i2c0";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart0_pins_b: uart0@1 {
- allwinner,pins = "PF2", "PF4";
- allwinner,function = "uart0";
+ i2c1_pins_a: i2c1@0 {
+ allwinner,pins = "PB18", "PB19";
+ allwinner,function = "i2c1";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart1_pins_a: uart1@0 {
- allwinner,pins = "PA10", "PA11";
- allwinner,function = "uart1";
+ i2c2_pins_a: i2c2@0 {
+ allwinner,pins = "PB20", "PB21";
+ allwinner,function = "i2c2";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- i2c0_pins_a: i2c0@0 {
- allwinner,pins = "PB0", "PB1";
- allwinner,function = "i2c0";
+ ir0_rx_pins_a: ir0@0 {
+ allwinner,pins = "PB4";
+ allwinner,function = "ir0";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- i2c1_pins_a: i2c1@0 {
- allwinner,pins = "PB18", "PB19";
- allwinner,function = "i2c1";
+ ir0_tx_pins_a: ir0@1 {
+ allwinner,pins = "PB3";
+ allwinner,function = "ir0";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- i2c2_pins_a: i2c2@0 {
- allwinner,pins = "PB20", "PB21";
- allwinner,function = "i2c2";
+ ir1_rx_pins_a: ir1@0 {
+ allwinner,pins = "PB23";
+ allwinner,function = "ir1";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- emac_pins_a: emac0@0 {
- allwinner,pins = "PA0", "PA1", "PA2",
- "PA3", "PA4", "PA5", "PA6",
- "PA7", "PA8", "PA9", "PA10",
- "PA11", "PA12", "PA13", "PA14",
- "PA15", "PA16";
- allwinner,function = "emac";
+ ir1_tx_pins_a: ir1@1 {
+ allwinner,pins = "PB22";
+ allwinner,function = "ir1";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
- ir0_rx_pins_a: ir0@0 {
- allwinner,pins = "PB4";
- allwinner,function = "ir0";
+ ps20_pins_a: ps20@0 {
+ allwinner,pins = "PI20", "PI21";
+ allwinner,function = "ps2";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ir0_tx_pins_a: ir0@1 {
- allwinner,pins = "PB3";
- allwinner,function = "ir0";
+ ps21_pins_a: ps21@0 {
+ allwinner,pins = "PH12", "PH13";
+ allwinner,function = "ps2";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ir1_rx_pins_a: ir1@0 {
- allwinner,pins = "PB23";
- allwinner,function = "ir1";
+ pwm0_pins_a: pwm0@0 {
+ allwinner,pins = "PB2";
+ allwinner,function = "pwm";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ir1_tx_pins_a: ir1@1 {
- allwinner,pins = "PB22";
- allwinner,function = "ir1";
+ pwm1_pins_a: pwm1@0 {
+ allwinner,pins = "PI3";
+ allwinner,function = "pwm";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+ spdif_tx_pins_a: spdif@0 {
+ allwinner,pins = "PB13";
+ allwinner,function = "spdif";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
spi0_pins_a: spi0@0 {
allwinner,pins = "PI11", "PI12", "PI13";
allwinner,function = "spi0";
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ps20_pins_a: ps20@0 {
- allwinner,pins = "PI20", "PI21";
- allwinner,function = "ps2";
+ uart0_pins_a: uart0@0 {
+ allwinner,pins = "PB22", "PB23";
+ allwinner,function = "uart0";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ps21_pins_a: ps21@0 {
- allwinner,pins = "PH12", "PH13";
- allwinner,function = "ps2";
+ uart0_pins_b: uart0@1 {
+ allwinner,pins = "PF2", "PF4";
+ allwinner,function = "uart0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ uart1_pins_a: uart1@0 {
+ allwinner,pins = "PA10", "PA11";
+ allwinner,function = "uart1";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
status = "disabled";
};
+ spdif: spdif@01c21000 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun4i-a10-spdif";
+ reg = <0x01c21000 0x400>;
+ interrupts = <13>;
+ clocks = <&apb0_gates 1>, <&spdif_clk>;
+ clock-names = "apb", "spdif";
+ dmas = <&dma SUN4I_DMA_NORMAL 2>,
+ <&dma SUN4I_DMA_NORMAL 2>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
ir0: ir@01c21800 {
compatible = "allwinner,sun4i-a10-ir";
clocks = <&apb0_gates 6>, <&ir0_clk>;
status = "okay";
};
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp152: pmic@30 {
+ compatible = "x-powers,axp152";
+ reg = <0x30>;
+ interrupts = <0>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_mk802>;
status = "okay";
};
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
&ohci0 {
status = "okay";
};
+&otg_sram {
+ status = "okay";
+};
+
&pio {
led_pins_mk802: led_pins@0 {
allwinner,pins = "PB2";
status = "okay";
};
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
&usbphy {
usb1_vbus-supply = <®_usb1_vbus>;
status = "okay";
status = "okay";
};
+&spi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>,
+ <&spi2_cs0_pins_a>;
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
regulator-name = "emac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
+ startup-delay-us = <20000>;
enable-active-high;
gpio = <&pio 0 2 GPIO_ACTIVE_HIGH>;
};
regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-wifi";
+ regulator-name = "vcc-wifi1";
+};
+
+®_ldo4 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi2";
};
®_usb1_vbus {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-hdmi";
- clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>,
- <&ahb_gates 44>;
+ clocks = <&pll3>, <&pll5 1>, <&ahb_gates 36>,
+ <&ahb_gates 43>, <&ahb_gates 44>;
status = "disabled";
};
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0";
- clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 44>;
+ clocks = <&pll3>, <&pll5 1>, <&ahb_gates 36>,
+ <&ahb_gates 44>;
status = "disabled";
};
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-tve0";
- clocks = <&pll5 1>, <&ahb_gates 34>, <&ahb_gates 36>,
- <&ahb_gates 44>;
+ clocks = <&pll3>, <&pll5 1>, <&ahb_gates 34>,
+ <&ahb_gates 36>, <&ahb_gates 44>;
status = "disabled";
};
};
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- nand_cs2_pins_a: nand_cs@2 {
- allwinner,pins = "PC17";
- allwinner,function = "nand0";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
+ spi2_pins_a: spi2@0 {
+ allwinner,pins = "PB12", "PB13", "PB14";
+ allwinner,function = "spi2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- nand_cs3_pins_a: nand_cs@3 {
- allwinner,pins = "PC18";
- allwinner,function = "nand0";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
+ spi2_cs0_pins_a: spi2_cs0@0 {
+ allwinner,pins = "PB11";
+ allwinner,function = "spi2";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
/dts-v1/;
#include "sun5i-a13.dtsi"
-#include "sunxi-common-regulators.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/pwm/pwm.h>
+#include "sun5i-reference-design-tablet.dtsi"
/ {
model = "Difrnce DIT4350";
compatible = "difrnce,dit4350", "allwinner,sun5i-a13";
-
- aliases {
- serial0 = &uart1;
- };
-
- backlight: backlight {
- compatible = "pwm-backlight";
- pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
- brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
- default-brightness-level = <8>;
- /* TODO: backlight uses axp gpio1 as enable pin */
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-};
-
-&cpu0 {
- cpu-supply = <®_dcdc2>;
-};
-
-&ehci0 {
- status = "okay";
-};
-
-&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-
- axp209: pmic@34 {
- reg = <0x34>;
- interrupts = <0>;
- };
-};
-
-#include "axp209.dtsi"
-
-&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
- status = "okay";
-
- pcf8563: rtc@51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
-};
-
-&lradc {
- vref-supply = <®_ldo2>;
- status = "okay";
-
- button@200 {
- label = "Volume Up";
- linux,code = <KEY_VOLUMEUP>;
- channel = <0>;
- voltage = <200000>;
- };
-
- button@400 {
- label = "Volume Down";
- linux,code = <KEY_VOLUMEDOWN>;
- channel = <0>;
- voltage = <400000>;
- };
-};
-
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_d709>;
- vmmc-supply = <®_vcc3v3>;
- bus-width = <4>;
- cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
- cd-inverted;
- status = "okay";
-};
-
-&otg_sram {
- status = "okay";
-};
-
-&pio {
- mmc0_cd_pin_d709: mmc0_cd_pin@0 {
- allwinner,pins = "PG0";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- allwinner,pins = "PG1";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PG2";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-};
-
-&pwm {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pins>;
- status = "okay";
-};
-
-®_dcdc2 {
- regulator-always-on;
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-cpu";
-};
-
-®_dcdc3 {
- regulator-always-on;
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <1250000>;
- regulator-name = "vdd-int-pll";
-};
-
-®_ldo1 {
- regulator-name = "vdd-rtc";
-};
-
-®_ldo2 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "avcc";
-};
-
-®_ldo3 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-wifi";
-};
-
-®_usb0_vbus {
- gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
- status = "okay";
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins_b>;
- status = "okay";
-};
-
-&usb_otg {
- dr_mode = "otg";
- status = "okay";
-};
-
-&usb0_vbus_pin_a {
- allwinner,pins = "PG12";
-};
-
-&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
- usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
- usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
- usb0_vbus-supply = <®_usb0_vbus>;
- usb1_vbus-supply = <®_ldo3>;
- status = "okay";
};
--- /dev/null
+/*
+ * Copyright 2016 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun5i-a13.dtsi"
+#include "sun5i-reference-design-tablet.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ model = "Empire Electronix M712 tablet";
+ compatible = "empire-electronix,m712", "allwinner,sun5i-a13";
+};
status = "okay";
};
+&otg_sram {
+ status = "okay";
+};
+
&pio {
mmc0_cd_pin_olinuxinom: mmc0_cd_pin@0 {
allwinner,pins = "PG0";
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PG2";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
+ allwinner,pins = "PG1";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ };
+
+ usb0_vbus_pin_olinuxinom: usb0_vbus_pin@0 {
+ allwinner,pins = "PG12";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
usb1_vbus_pin_olinuxinom: usb1_vbus_pin@0 {
allwinner,pins = "PG11";
allwinner,function = "gpio_out";
};
};
+®_usb0_vbus {
+ pinctrl-0 = <&usb0_vbus_pin_olinuxinom>;
+ gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
®_usb1_vbus {
pinctrl-0 = <&usb1_vbus_pin_olinuxinom>;
gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>;
status = "okay";
};
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
+ usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+ usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+ usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_usb1_vbus>;
status = "okay";
};
status = "okay";
};
-&nfc {
- pinctrl-names = "default";
- pinctrl-0 = <&nand_pins_a &nand_cs0_pins_a &nand_rb0_pins_a>;
- status = "okay";
-
- nand@0 {
- #address-cells = <2>;
- #size-cells = <2>;
- reg = <0>;
- allwinner,rb = <0>;
- nand-ecc-mode = "hw";
- allwinner,randomize;
- };
-};
-
&ohci0 {
status = "okay";
};
/dts-v1/;
#include "sun5i-a13.dtsi"
-#include "sun5i-q8-common.dtsi"
+#include "sun5i-reference-design-tablet.dtsi"
/ {
model = "Q8 A13 Tablet";
compatible = "allwinner,q8-a13", "allwinner,sun5i-a13";
+
+ panel: panel {
+ compatible = "urt,umsh-8596md-t", "simple-panel";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ /* TODO: lcd panel uses axp gpio0 as enable pin */
+ backlight = <&backlight>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ panel_input: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon0_out_lcd>;
+ };
+ };
+ };
+};
+
+&be0 {
+ status = "okay";
};
-®_ldo3 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-wifi";
+&tcon0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_rgb666_pins>;
+ status = "okay";
};
-&usbphy {
- usb1_vbus-supply = <®_ldo3>;
+&tcon0_out {
+ tcon0_out_lcd: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&panel_input>;
+ };
};
/dts-v1/;
#include "sun5i-a13.dtsi"
-#include "sunxi-common-regulators.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "sun5i-reference-design-tablet.dtsi"
#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/pwm/pwm.h>
/ {
model = "Utoo P66";
compatible = "utoo,p66", "allwinner,sun5i-a13";
- backlight: backlight {
- compatible = "pwm-backlight";
- pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
- /* Note levels of 10 / 20% result in backlight off */
- brightness-levels = <0 30 40 50 60 70 80 90 100>;
- default-brightness-level = <6>;
- /* TODO: backlight uses axp gpio1 as enable pin */
+ /* The P66 uses the uart pins as gpios */
+ aliases {
+ /delete-property/serial0;
+ };
+
+ chosen {
+ /delete-property/stdout-path;
};
i2c_lcd: i2c@0 {
};
};
-&codec {
- pinctrl-names = "default";
- pinctrl-0 = <&codec_pa_pin>;
- allwinner,pa-gpios = <&pio 6 3 GPIO_ACTIVE_HIGH>; /* PG3 */
- status = "okay";
-};
-
-&cpu0 {
- cpu-supply = <®_dcdc2>;
+&backlight {
+ /* Note levels of 10 / 20% result in backlight off */
+ brightness-levels = <0 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <6>;
};
-&ehci0 {
- status = "okay";
+&codec {
+ allwinner,pa-gpios = <&pio 6 3 GPIO_ACTIVE_HIGH>; /* PG3 */
};
-&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-
- axp209: pmic@34 {
- reg = <0x34>;
- interrupts = <0>;
- };
+&codec_pa_pin {
+ allwinner,pins = "PG3";
};
-#include "axp209.dtsi"
-
&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
- status = "okay";
-
icn8318: touchscreen@40 {
compatible = "chipone,icn8318";
reg = <0x40>;
touchscreen-inverted-x;
touchscreen-swapped-x-y;
};
-
- pcf8563: rtc@51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
-};
-
-&lradc {
- vref-supply = <®_ldo2>;
- status = "okay";
-
- button@200 {
- label = "Volume Up";
- linux,code = <KEY_VOLUMEUP>;
- channel = <0>;
- voltage = <200000>;
- };
-
- button@400 {
- label = "Volume Down";
- linux,code = <KEY_VOLUMEDOWN>;
- channel = <0>;
- voltage = <400000>;
- };
-};
-
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_p66>;
- vmmc-supply = <®_vcc3v3>;
- bus-width = <4>;
- cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
- cd-inverted;
- status = "okay";
};
&mmc2 {
};
};
-&otg_sram {
- status = "okay";
-};
-
&pio {
- codec_pa_pin: codec_pa_pin@0 {
- allwinner,pins = "PG3";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- mmc0_cd_pin_p66: mmc0_cd_pin@0 {
- allwinner,pins = "PG0";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-
- usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
- allwinner,pins = "PG1";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PG2";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-
i2c_lcd_pins: i2c_lcd_pin@0 {
allwinner,pins = "PG10", "PG12";
allwinner,function = "gpio_out";
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- usb0_vbus_pin_a: usb0_vbus_pin@0 {
- allwinner,pins = "PB4";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-};
-
-&pwm {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pins>;
- status = "okay";
-};
-
-®_dcdc2 {
- regulator-always-on;
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1500000>;
- regulator-name = "vdd-cpu";
-};
-
-®_dcdc3 {
- regulator-always-on;
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-int-pll";
-};
-
-®_ldo1 {
- regulator-name = "vdd-rtc";
-};
-
-®_ldo2 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "avcc";
-};
-
-®_ldo3 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-wifi";
};
®_usb0_vbus {
gpio = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
- status = "okay";
};
-&usb_otg {
- dr_mode = "otg";
- status = "okay";
+&uart1 {
+ /* The P66 uses the uart pins as gpios */
+ status = "disabled";
};
-&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
- usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
- usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
- usb0_vbus-supply = <®_usb0_vbus>;
- usb1_vbus-supply = <®_ldo3>;
- status = "okay";
+&usb0_vbus_pin_a {
+ allwinner,pins = "PB4";
};
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0";
- clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 44>;
+ clocks = <&ahb_gates 36>, <&ahb_gates 44>, <&de_be_clk>,
+ <&tcon_ch0_clk>, <&dram_gates 26>;
status = "disabled";
};
};
<10>, <13>,
<14>, <20>,
<21>, <22>,
- <28>, <32>, <36>,
- <40>, <44>,
+ <28>, <32>, <34>,
+ <36>, <40>, <44>,
<46>, <51>,
<52>;
clock-output-names = "ahb_usbotg", "ahb_ehci",
"ahb_mmc2", "ahb_nand",
"ahb_sdram", "ahb_spi0",
"ahb_spi1", "ahb_spi2",
- "ahb_stimer", "ahb_ve", "ahb_lcd",
- "ahb_csi", "ahb_de_be",
+ "ahb_stimer", "ahb_ve", "ahb_tve",
+ "ahb_lcd", "ahb_csi", "ahb_de_be",
"ahb_de_fe", "ahb_iep",
"ahb_mali400";
};
"apb1_i2c2", "apb1_uart1",
"apb1_uart3";
};
+
+ dram_gates: clk@01c20100 {
+ #clock-cells = <1>;
+ compatible = "allwinner,sun5i-a13-dram-gates-clk",
+ "allwinner,sun4i-a10-gates-clk";
+ reg = <0x01c20100 0x4>;
+ clocks = <&pll5 0>;
+ clock-indices = <0>,
+ <1>,
+ <25>,
+ <26>,
+ <29>,
+ <31>;
+ clock-output-names = "dram_ve",
+ "dram_csi",
+ "dram_de_fe",
+ "dram_de_be",
+ "dram_ace",
+ "dram_iep";
+ };
+
+ de_be_clk: clk@01c20104 {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-display-clk";
+ reg = <0x01c20104 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll5 1>;
+ clock-output-names = "de-be";
+ };
+
+ de_fe_clk: clk@01c2010c {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-display-clk";
+ reg = <0x01c2010c 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll5 1>;
+ clock-output-names = "de-fe";
+ };
+
+ tcon_ch0_clk: clk@01c20118 {
+ #clock-cells = <0>;
+ #reset-cells = <1>;
+ compatible = "allwinner,sun4i-a10-tcon-ch0-clk";
+ reg = <0x01c20118 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+ clock-output-names = "tcon-ch0-sclk";
+ };
+
+ tcon_ch1_clk: clk@01c2012c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-tcon-ch1-clk";
+ reg = <0x01c2012c 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+ clock-output-names = "tcon-ch1-sclk";
+ };
+ };
+
+ display-engine {
+ compatible = "allwinner,sun5i-a13-display-engine";
+ allwinner,pipelines = <&fe0>;
};
soc@01c00000 {
+ tcon0: lcd-controller@01c0c000 {
+ compatible = "allwinner,sun5i-a13-tcon";
+ reg = <0x01c0c000 0x1000>;
+ interrupts = <44>;
+ resets = <&tcon_ch0_clk 1>;
+ reset-names = "lcd";
+ clocks = <&ahb_gates 36>,
+ <&tcon_ch0_clk>,
+ <&tcon_ch1_clk>;
+ clock-names = "ahb",
+ "tcon-ch0",
+ "tcon-ch1";
+ clock-output-names = "tcon-pixel-clock";
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon0_in: port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ tcon0_in_be0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&be0_out_tcon0>;
+ };
+ };
+
+ tcon0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ };
+ };
+
pwm: pwm@01c20e00 {
compatible = "allwinner,sun5i-a13-pwm";
reg = <0x01c20e00 0xc>;
#pwm-cells = <3>;
status = "disabled";
};
+
+ fe0: display-frontend@01e00000 {
+ compatible = "allwinner,sun5i-a13-display-frontend";
+ reg = <0x01e00000 0x20000>;
+ interrupts = <47>;
+ clocks = <&ahb_gates 46>, <&de_fe_clk>,
+ <&dram_gates 25>;
+ clock-names = "ahb", "mod",
+ "ram";
+ resets = <&de_fe_clk>;
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fe0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ fe0_out_be0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&be0_in_fe0>;
+ };
+ };
+ };
+ };
+
+ be0: display-backend@01e60000 {
+ compatible = "allwinner,sun5i-a13-display-backend";
+ reg = <0x01e60000 0x10000>;
+ clocks = <&ahb_gates 44>, <&de_be_clk>,
+ <&dram_gates 26>;
+ clock-names = "ahb", "mod",
+ "ram";
+ resets = <&de_be_clk>;
+ status = "disabled";
+
+ assigned-clocks = <&de_be_clk>;
+ assigned-clock-rates = <300000000>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ be0_in: port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ be0_in_fe0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&fe0_out_be0>;
+ };
+ };
+
+ be0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ be0_out_tcon0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon0_in_be0>;
+ };
+ };
+ };
+ };
};
};
&pio {
compatible = "allwinner,sun5i-a13-pinctrl";
+ lcd_rgb666_pins: lcd_rgb666@0 {
+ allwinner,pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7",
+ "PD10", "PD11", "PD12", "PD13", "PD14", "PD15",
+ "PD18", "PD19", "PD20", "PD21", "PD22", "PD23",
+ "PD24", "PD25", "PD26", "PD27";
+ allwinner,function = "lcd0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
uart1_pins_a: uart1@0 {
allwinner,pins = "PE10", "PE11";
allwinner,function = "uart1";
/ {
model = "NextThing C.H.I.P.";
- compatible = "nextthing,chip", "allwinner,sun5i-r8";
+ compatible = "nextthing,chip", "allwinner,sun5i-r8", "allwinner,sun5i-a13";
aliases {
i2c0 = &i2c0;
};
};
+&be0 {
+ status = "okay";
+};
+
&codec {
status = "okay";
};
status = "okay";
};
-&nfc {
- pinctrl-names = "default";
- pinctrl-0 = <&nand_pins_a &nand_cs0_pins_a &nand_rb0_pins_a>;
- status = "okay";
-
- nand@0 {
- #address-cells = <2>;
- #size-cells = <2>;
- reg = <0>;
- allwinner,rb = <0>;
- nand-ecc-mode = "hw";
- nand-on-flash-bbt;
- };
-};
-
&ohci0 {
status = "okay";
};
status = "okay";
};
+&tcon0 {
+ status = "okay";
+};
+
+&tve0 {
+ status = "okay";
+};
+
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins_b>;
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-tve0";
- clocks = <&pll5 1>, <&ahb_gates 34>, <&ahb_gates 36>,
- <&ahb_gates 44>;
+ clocks = <&ahb_gates 34>, <&ahb_gates 36>,
+ <&ahb_gates 44>, <&de_be_clk>,
+ <&tcon_ch1_clk>, <&dram_gates 26>;
status = "disabled";
};
};
+
+ soc@01c00000 {
+ tve0: tv-encoder@01c0a000 {
+ compatible = "allwinner,sun4i-a10-tv-encoder";
+ reg = <0x01c0a000 0x1000>;
+ clocks = <&ahb_gates 34>;
+ resets = <&tcon_ch0_clk 0>;
+ status = "disabled";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tve0_in_tcon0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon0_out_tve0>;
+ };
+ };
+ };
+ };
+};
+
+&tcon0_out {
+ tcon0_out_tve0: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&tve0_in_tcon0>;
+ };
};
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include "sunxi-reference-design-tablet.dtsi"
+
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ aliases {
+ serial0 = &uart1;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <8>;
+ /* TODO: backlight uses axp gpio1 as enable pin */
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&codec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&codec_pa_pin>;
+ allwinner,pa-gpios = <&pio 6 10 GPIO_ACTIVE_HIGH>; /* PG10 */
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&i2c0 {
+ axp209: pmic@34 {
+ reg = <0x34>;
+ interrupts = <0>;
+ };
+};
+
+&i2c1 {
+ pcf8563: rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+};
+
+#include "axp209.dtsi"
+
+&lradc {
+ vref-supply = <®_ldo2>;
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v0>;
+ bus-width = <4>;
+ cd-gpios = <&pio 6 0 GPIO_ACTIVE_HIGH>; /* PG0 */
+ cd-inverted;
+ status = "okay";
+};
+
+&otg_sram {
+ status = "okay";
+};
+
+&pio {
+ codec_pa_pin: codec_pa_pin@0 {
+ allwinner,pins = "PG10";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin: mmc0_cd_pin@0 {
+ allwinner,pins = "PG0";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
+ allwinner,pins = "PG1";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ };
+
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PG2";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb0_vbus_pin_a: usb0_vbus_pin@0 {
+ allwinner,pins = "PG12";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-pll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+®_ldo3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_usb0_vbus {
+ gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins_b>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
+ usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+ usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb0_vbus-supply = <®_usb0_vbus>;
+ usb1_vbus-supply = <®_ldo3>;
+ status = "okay";
+};
clock-output-names = "osc24M";
};
+ osc3M: osc3M_clk {
+ compatible = "fixed-factor-clock";
+ #clock-cells = <0>;
+ clock-div = <8>;
+ clock-mult = <1>;
+ clocks = <&osc24M>;
+ clock-output-names = "osc3M";
+ };
+
osc32k: clk@0 {
#clock-cells = <0>;
compatible = "fixed-clock";
"pll2-4x", "pll2-8x";
};
+ pll3: clk@01c20010 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-pll3-clk";
+ reg = <0x01c20010 0x4>;
+ clocks = <&osc3M>;
+ clock-output-names = "pll3";
+ };
+
+ pll3x2: pll3x2_clk {
+ compatible = "allwinner,sun4i-a10-pll3-2x-clk", "fixed-factor-clock";
+ #clock-cells = <0>;
+ clock-div = <1>;
+ clock-mult = <2>;
+ clocks = <&pll3>;
+ clock-output-names = "pll3-2x";
+ };
+
pll4: clk@01c20018 {
#clock-cells = <0>;
compatible = "allwinner,sun4i-a10-pll1-clk";
clock-output-names = "pll6_sata", "pll6_other", "pll6";
};
+ pll7: clk@01c20030 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-pll3-clk";
+ reg = <0x01c20030 0x4>;
+ clocks = <&osc3M>;
+ clock-output-names = "pll7";
+ };
+
+ pll7x2: pll7x2_clk {
+ compatible = "fixed-factor-clock";
+ #clock-cells = <0>;
+ clock-div = <1>;
+ clock-mult = <2>;
+ clocks = <&pll7>;
+ clock-output-names = "pll7-2x";
+ };
+
/* dummy is 200M */
cpu: cpu@01c20054 {
#clock-cells = <0>;
#dma-cells = <2>;
};
- nfc: nand@01c03000 {
- compatible = "allwinner,sun4i-a10-nand";
- reg = <0x01c03000 0x1000>;
- interrupts = <37>;
- clocks = <&ahb_gates 13>, <&nand_clk>;
- clock-names = "ahb", "mod";
- #address-cells = <1>;
- #size-cells = <0>;
- status = "disabled";
- };
-
spi0: spi@01c05000 {
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c05000 0x1000>;
allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
- nand_pins_a: nand_base0@0 {
- allwinner,pins = "PC0", "PC1", "PC2",
- "PC5", "PC8", "PC9", "PC10",
- "PC11", "PC12", "PC13", "PC14",
- "PC15";
- allwinner,function = "nand0";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
- };
-
- nand_cs0_pins_a: nand_cs@0 {
- allwinner,pins = "PC4";
- allwinner,function = "nand0";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
- };
-
- nand_cs1_pins_a: nand_cs@1 {
- allwinner,pins = "PC3";
- allwinner,function = "nand0";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
- };
-
- nand_rb0_pins_a: nand_rb@0 {
- allwinner,pins = "PC6";
- allwinner,function = "nand0";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
- };
-
- nand_rb1_pins_a: nand_rb@1 {
- allwinner,pins = "PC7";
- allwinner,function = "nand0";
- allwinner,drive = <0>;
- allwinner,pull = <0>;
- };
-
uart3_pins_a: uart3@0 {
allwinner,pins = "PG9", "PG10";
allwinner,function = "uart3";
pinctrl-0 = <&led_pins_m9>;
blue {
- label = "m9:blue:usr";
+ label = "m9:blue:pwr";
gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
};
};
};
+&cpu0 {
+ cpu-supply = <®_dcdc3>;
+};
+
&ehci0 {
status = "okay";
};
pinctrl-0 = <&gmac_pins_mii_a>;
phy = <&phy1>;
phy-mode = "mii";
+ phy-supply = <®_dldo1>;
status = "okay";
phy1: ethernet-phy@1 {
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_m9>;
- vmmc-supply = <®_vcc3v3>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
cd-inverted;
status = "okay";
};
+&p2wi {
+ status = "okay";
+
+ axp22x: pmic@68 {
+ compatible = "x-powers,axp221";
+ reg = <0x68>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp22x.dtsi"
+
&pio {
led_pins_m9: led_pins@0 {
allwinner,pins = "PH13";
};
};
+®_aldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpus"; /* This is an educated guess */
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_dcdc2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-sys-dll";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-ethernet-phy";
+};
+
+/*
+ * Both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
+ * to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
+ * marked as regulator-always-on.
+ */
+®_dldo4 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-usb-hub";
+};
+
®_usb1_vbus {
pinctrl-names = "default";
pinctrl-0 = <&usb1_vbus_pin_m9>;
&usbphy {
usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_aldo1>;
status = "okay";
};
pinctrl-0 = <&led_pins_m9>;
blue {
- label = "m9:blue:usr";
+ label = "a1000g:blue:pwr";
gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
};
};
};
+&cpu0 {
+ cpu-supply = <®_dcdc3>;
+};
+
&ehci0 {
status = "okay";
};
pinctrl-0 = <&gmac_pins_mii_a>;
phy = <&phy1>;
phy-mode = "mii";
+ phy-supply = <®_dldo1>;
status = "okay";
phy1: ethernet-phy@1 {
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_m9>;
- vmmc-supply = <®_vcc3v3>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
cd-inverted;
status = "okay";
};
+&p2wi {
+ status = "okay";
+
+ axp22x: pmic@68 {
+ compatible = "x-powers,axp221";
+ reg = <0x68>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp22x.dtsi"
+
&pio {
led_pins_m9: led_pins@0 {
allwinner,pins = "PH13";
};
};
+®_aldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpus"; /* This is an educated guess */
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_dcdc2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-sys-dll";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-ethernet-phy";
+};
+
+/*
+ * Both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
+ * to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
+ * marked as regulator-always-on.
+ */
+®_dldo4 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-usb-hub";
+};
+
®_usb1_vbus {
pinctrl-names = "default";
pinctrl-0 = <&usb1_vbus_pin_m9>;
&usbphy {
usb1_vbus-supply = <®_usb1_vbus>;
+ usb2_vbus-supply = <®_aldo1>;
status = "okay";
};
};
mmc0: mmc@01c0f000 {
- compatible = "allwinner,sun5i-a13-mmc";
+ compatible = "allwinner,sun7i-a20-mmc",
+ "allwinner,sun5i-a13-mmc";
reg = <0x01c0f000 0x1000>;
clocks = <&ahb1_gates 8>,
<&mmc0_clk 0>,
};
mmc1: mmc@01c10000 {
- compatible = "allwinner,sun5i-a13-mmc";
+ compatible = "allwinner,sun7i-a20-mmc",
+ "allwinner,sun5i-a13-mmc";
reg = <0x01c10000 0x1000>;
clocks = <&ahb1_gates 9>,
<&mmc1_clk 0>,
};
mmc2: mmc@01c11000 {
- compatible = "allwinner,sun5i-a13-mmc";
+ compatible = "allwinner,sun7i-a20-mmc",
+ "allwinner,sun5i-a13-mmc";
reg = <0x01c11000 0x1000>;
clocks = <&ahb1_gates 10>,
<&mmc2_clk 0>,
};
mmc3: mmc@01c12000 {
- compatible = "allwinner,sun5i-a13-mmc";
+ compatible = "allwinner,sun7i-a20-mmc",
+ "allwinner,sun5i-a13-mmc";
reg = <0x01c12000 0x1000>;
clocks = <&ahb1_gates 11>,
<&mmc3_clk 0>,
/dts-v1/;
#include "sun6i-a31s.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include "sun6i-reference-design-tablet.dtsi"
/ {
model = "Colorfly E708 Q1 tablet";
compatible = "colorfly,e708-q1", "allwinner,sun6i-a31s";
-
- aliases {
- serial0 = &uart0;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-};
-
-&cpu0 {
- cpu-supply = <®_dcdc3>;
-};
-
-&ehci0 {
- /* rtl8188etv wifi is connected here */
- status = "okay";
};
&lradc {
};
};
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_e708_q1>;
- vmmc-supply = <®_dcdc1>;
- bus-width = <4>;
- cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
- cd-inverted;
- status = "okay";
-};
-
-&pio {
- mma8452_int_e708_q1: mma8452_int_pin@0 {
- allwinner,pins = "PA9";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-
- mmc0_cd_pin_e708_q1: mmc0_cd_pin@0 {
- allwinner,pins = "PA8";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-};
-
-&p2wi {
- status = "okay";
-
- axp22x: pmic@68 {
- compatible = "x-powers,axp221";
- reg = <0x68>;
- interrupt-parent = <&nmi_intc>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- };
-};
-
-#include "axp22x.dtsi"
-
-®_aldo3 {
- regulator-always-on;
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "avcc";
-};
-
-®_dc1sw {
- regulator-name = "vcc-lcd";
-};
-
-®_dc5ldo {
- regulator-always-on;
- regulator-min-microvolt = <700000>;
- regulator-max-microvolt = <1320000>;
- regulator-name = "vdd-cpus"; /* This is an educated guess */
-};
-
-®_dcdc1 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-3v0";
-};
-
-®_dcdc2 {
- regulator-min-microvolt = <700000>;
- regulator-max-microvolt = <1320000>;
- regulator-name = "vdd-gpu";
-};
-
-®_dcdc3 {
- regulator-always-on;
- regulator-min-microvolt = <700000>;
- regulator-max-microvolt = <1320000>;
- regulator-name = "vdd-cpu";
-};
-
-®_dcdc4 {
- regulator-always-on;
- regulator-min-microvolt = <700000>;
- regulator-max-microvolt = <1320000>;
- regulator-name = "vdd-sys-dll";
-};
-
-®_dcdc5 {
- regulator-always-on;
- regulator-min-microvolt = <1500000>;
- regulator-max-microvolt = <1500000>;
- regulator-name = "vcc-dram";
-};
-
-®_dldo1 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-wifi";
-};
-
®_dldo2 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
&simplefb_lcd {
- vcc-lcd-supply = <®_dc1sw>;
vcc-pg-supply = <®_dldo2>;
};
-
-/*
- * FIXME for now we only support host mode and rely on u-boot to have
- * turned on Vbus which is controlled by the axp221 pmic on the board.
- *
- * Once we have axp221 power-supply and vbus-usb support we should switch
- * to fully supporting otg.
- */
-&usb_otg {
- dr_mode = "host";
- status = "okay";
-};
-
-&usbphy {
- usb1_vbus-supply = <®_dldo1>;
- status = "okay";
-};
--- /dev/null
+/*
+ * Copyright 2016 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun6i-a31s.dtsi"
+#include "sun6i-reference-design-tablet.dtsi"
+
+/ {
+ model = "iNet Q972 tablet";
+ compatible = "inet-tek,inet-q972", "allwinner,sun6i-a31s";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+
+ ft5406ee8: touchscreen@38 {
+ compatible = "edt,edt-ft5406";
+ reg = <0x38>;
+ interrupt-parent = <&pio>;
+ interrupts = <0 3 IRQ_TYPE_LEVEL_HIGH>; /* PA3 */
+ touchscreen-size-x = <768>;
+ touchscreen-size-y = <1024>;
+ touchscreen-swapped-x-y;
+ };
+};
+
+&lradc {
+ vref-supply = <®_aldo3>;
+ status = "okay";
+
+ button@200 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <200000>;
+ };
+
+ button@900 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <900000>;
+ };
+
+ button@1200 {
+ label = "Back";
+ linux,code = <KEY_BACK>;
+ channel = <0>;
+ voltage = <1200000>;
+ };
+};
+
+&ohci1 {
+ status = "okay";
+};
/ {
model = "MSI Primo81 tablet";
compatible = "msi,primo81", "allwinner,sun6i-a31s";
-
- aliases {
- serial0 = &uart0;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
};
&cpu0 {
};
®_dc1sw {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
regulator-name = "vcc-lcd";
};
®_dc1sw {
regulator-name = "vcc-lcd-usb2";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
};
®_dc5ldo {
--- /dev/null
+/*
+ * Copyright 2016 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc3>;
+};
+
+&ehci0 {
+ /* Wifi is connected here */
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_e708_q1>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
+ cd-inverted;
+ status = "okay";
+};
+
+&pio {
+ mmc0_cd_pin_e708_q1: mmc0_cd_pin@0 {
+ allwinner,pins = "PA8";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PA15";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+};
+
+&p2wi {
+ status = "okay";
+
+ axp22x: pmic@68 {
+ compatible = "x-powers,axp221";
+ reg = <0x68>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ drivevbus-supply = <®_vcc5v0>;
+ x-powers,drive-vbus-en;
+ };
+};
+
+#include "axp22x.dtsi"
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+};
+
+®_dc1sw {
+ regulator-name = "vcc-lcd";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpus"; /* This is an educated guess */
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-gpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-name = "vdd-sys-dll";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
+&simplefb_lcd {
+ vcc-lcd-supply = <®_dc1sw>;
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb0_vbus-supply = <®_drivevbus>;
+ usb1_vbus-supply = <®_dldo1>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * Copyright 2016 Luo Yi <luoyi.ly@gmail.com>
+ *
+ * Thanks to the original work by Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ model = "Banana Pi BPI-M1-Plus";
+ compatible = "sinovoip,bpi-m1-plus", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_bpi_m1p>;
+
+ green {
+ label = "bananapi-m1-plus:green:usr";
+ gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
+ };
+
+ pwr {
+ label = "bananapi-m1-plus:pwr:usr";
+ gpios = <&pio 7 25 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ mmc3_pwrseq: mmc3_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pwrseq_pin_bpi_m1p>;
+ reset-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 WL-PMU-EN */
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_power_pin_bpi_m1p>;
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&ahci {
+ status = "okay";
+};
+
+&codec {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&gmac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ phy-supply = <®_gmac_3v3>;
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+};
+
+&ir0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_rx_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bpi_m1p>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&mmc3_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ enable-sdio-wakeup;
+ status = "okay";
+
+ brcmf: bcrmf@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <7 15 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "host-wake";
+ };
+};
+
+&mmc3_pins_a {
+ /* AP6210 requires pull-up */
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pio {
+ gmac_power_pin_bpi_m1p: gmac_power_pin@0 {
+ allwinner,pins = "PH23";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_bpi_m1p: led_pins@0 {
+ allwinner,pins = "PH24", "PH25";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin_bpi_m1p: mmc0_cd_pin@0 {
+ allwinner,pins = "PH10";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ mmc3_pwrseq_pin_bpi_m1p: mmc3_pwrseq_pin@0 {
+ allwinner,pins = "PH22";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
pinctrl-0 = <&mmc3_pwrseq_pin_cubietruck>;
reset-gpios = <&pio 7 9 GPIO_ACTIVE_LOW>; /* PH9 WIFI_EN */
};
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "On-board SPDIF";
+
+ simple-audio-card,cpu {
+ sound-dai = <&spdif>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&spdif_out>;
+ };
+ };
+
+ spdif_out: spdif-out {
+ #sound-dai-cells = <0>;
+ compatible = "linux,spdif-dit";
+ };
};
&ahci {
status = "okay";
};
+&spdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spdif_tx_pins_a>;
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
default-state = "on";
};
};
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "On-board SPDIF";
+
+ simple-audio-card,cpu {
+ sound-dai = <&spdif>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&spdif_out>;
+ };
+ };
+
+ spdif_out: spdif-out {
+ #sound-dai-cells = <0>;
+ compatible = "linux,spdif-dit";
+ };
};
&ahci {
®_ahci_5v {
status = "okay";
};
+
+&spdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spdif_tx_pins_a>;
+ status = "okay";
+};
status = "okay";
};
+&codec {
+ status = "okay";
+};
+
&cpu0 {
cpu-supply = <®_dcdc2>;
};
&gmac {
pinctrl-names = "default";
pinctrl-0 = <&gmac_pins_rgmii_a>;
- phy = <&phy1>;
phy-mode = "rgmii";
phy-supply = <®_gmac_3v3>;
status = "okay";
- phy1: ethernet-phy@1 {
- reg = <1>;
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch: ethernet-switch@1e {
+ compatible = "brcm,bcm53125";
+ reg = <30>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port0: port@0 {
+ reg = <0>;
+ label = "lan2";
+ };
+
+ port1: port@1 {
+ reg = <1>;
+ label = "lan3";
+ };
+
+ port2: port@2 {
+ reg = <2>;
+ label = "lan4";
+ };
+
+ port3: port@3 {
+ reg = <3>;
+ label = "wan";
+ };
+
+ port4: port@4 {
+ reg = <4>;
+ label = "lan1";
+ };
+
+ port8: port@8 {
+ reg = <8>;
+ label = "cpu";
+ ethernet = <&gmac>;
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
};
};
status = "okay";
};
-&ohci1 {
- status = "okay";
-};
-
&otg_sram {
status = "okay";
};
#include "axp209.dtsi"
®_ahci_5v {
- gpio = <&pio 1 3 0>; /* PB3 */
+ gpio = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
status = "okay";
};
status = "okay";
};
-®_usb1_vbus {
- status = "okay";
-};
-
®_usb2_vbus {
+ gpio = <&pio 7 12 GPIO_ACTIVE_HIGH>; /* PH12 */
status = "okay";
};
status = "okay";
};
+&usb2_vbus_pin_a {
+ allwinner,pins = "PH12";
+};
+
&usbphy {
pinctrl-names = "default";
pinctrl-0 = <&usb0_id_detect_pin>;
usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
usb0_vbus_power-supply = <&usb_power_supply>;
usb0_vbus-supply = <®_usb0_vbus>;
- usb1_vbus-supply = <®_usb1_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";
};
--- /dev/null
+ /*
+ * Copyright 2015 - Ultimaker B.V.
+ * Author Olliver Schinagl <oliver@schinagl.nl>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sun7i-a20-olinuxino-lime2.dts"
+
+/ {
+ model = "Olimex A20-OLinuXino-LIME2-eMMC";
+ compatible = "olimex,a20-olinuxino-lime2-emmc", "allwinner,sun7i-a20";
+
+ mmc2_pwrseq: pwrseq {
+ pinctrl-0 = <&mmc2_pins_nrst>;
+ pinctrl-names = "default";
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&pio 2 16 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&pio {
+ mmc2_pins_nrst: mmc2@0 {
+ allwinner,pins = "PC16";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ non-removable;
+ mmc-pwrseq = <&mmc2_pwrseq>;
+ status = "okay";
+
+ emmc: emmc@0 {
+ reg = <0>;
+ compatible = "mmc-card";
+ broken-hpi;
+ };
+};
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-hdmi";
- clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 43>,
- <&ahb_gates 44>, <&dram_gates 26>;
+ clocks = <&ahb_gates 36>, <&ahb_gates 43>,
+ <&ahb_gates 44>, <&de_be0_clk>,
+ <&tcon0_ch1_clk>, <&dram_gates 26>;
status = "disabled";
};
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0";
- clocks = <&pll5 1>, <&ahb_gates 36>, <&ahb_gates 44>,
+ clocks = <&ahb_gates 36>, <&ahb_gates 44>,
+ <&de_be0_clk>, <&tcon0_ch0_clk>,
<&dram_gates 26>;
status = "disabled";
};
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-tve0";
- clocks = <&pll5 1>, <&ahb_gates 34>, <&ahb_gates 36>,
- <&ahb_gates 44>, <&dram_gates 26>;
+ clocks = <&ahb_gates 34>, <&ahb_gates 36>,
+ <&ahb_gates 44>,
+ <&de_be0_clk>, <&tcon0_ch1_clk>,
+ <&dram_gates 5>, <&dram_gates 26>;
status = "disabled";
};
};
clock-output-names = "osc24M";
};
+ osc3M: osc3M_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clock-div = <8>;
+ clock-mult = <1>;
+ clocks = <&osc24M>;
+ clock-output-names = "osc3M";
+ };
+
osc32k: clk@0 {
#clock-cells = <0>;
compatible = "fixed-clock";
"pll2-4x", "pll2-8x";
};
+ pll3: clk@01c20010 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-pll3-clk";
+ reg = <0x01c20010 0x4>;
+ clocks = <&osc3M>;
+ clock-output-names = "pll3";
+ };
+
+ pll3x2: pll3x2_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&pll3>;
+ clock-div = <1>;
+ clock-mult = <2>;
+ clock-output-names = "pll3-2x";
+ };
+
pll4: clk@01c20018 {
#clock-cells = <0>;
compatible = "allwinner,sun7i-a20-pll4-clk";
"pll6_div_4";
};
+ pll7: clk@01c20030 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-pll3-clk";
+ reg = <0x01c20030 0x4>;
+ clocks = <&osc3M>;
+ clock-output-names = "pll7";
+ };
+
+ pll7x2: pll7x2_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-factor-clock";
+ clocks = <&pll7>;
+ clock-div = <1>;
+ clock-mult = <2>;
+ clock-output-names = "pll7-2x";
+ };
+
pll8: clk@01c20040 {
#clock-cells = <0>;
compatible = "allwinner,sun7i-a20-pll4-clk";
<5>, <6>, <7>,
<8>, <10>;
clock-output-names = "apb0_codec", "apb0_spdif",
- "apb0_ac97", "apb0_iis0", "apb0_iis1",
+ "apb0_ac97", "apb0_i2s0", "apb0_i2s1",
"apb0_pio", "apb0_ir0", "apb0_ir1",
- "apb0_iis2", "apb0_keypad";
+ "apb0_i2s2", "apb0_keypad";
};
apb1: clk@01c20058 {
clock-output-names = "ir1";
};
+ i2s0_clk: clk@01c200b8 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod1-clk";
+ reg = <0x01c200b8 0x4>;
+ clocks = <&pll2 SUN4I_A10_PLL2_8X>,
+ <&pll2 SUN4I_A10_PLL2_4X>,
+ <&pll2 SUN4I_A10_PLL2_2X>,
+ <&pll2 SUN4I_A10_PLL2_1X>;
+ clock-output-names = "i2s0";
+ };
+
+ ac97_clk: clk@01c200bc {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod1-clk";
+ reg = <0x01c200bc 0x4>;
+ clocks = <&pll2 SUN4I_A10_PLL2_8X>,
+ <&pll2 SUN4I_A10_PLL2_4X>,
+ <&pll2 SUN4I_A10_PLL2_2X>,
+ <&pll2 SUN4I_A10_PLL2_1X>;
+ clock-output-names = "ac97";
+ };
+
+ spdif_clk: clk@01c200c0 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod1-clk";
+ reg = <0x01c200c0 0x4>;
+ clocks = <&pll2 SUN4I_A10_PLL2_8X>,
+ <&pll2 SUN4I_A10_PLL2_4X>,
+ <&pll2 SUN4I_A10_PLL2_2X>,
+ <&pll2 SUN4I_A10_PLL2_1X>;
+ clock-output-names = "spdif";
+ };
+
keypad_clk: clk@01c200c4 {
#clock-cells = <0>;
compatible = "allwinner,sun4i-a10-mod0-clk";
clock-output-names = "spi3";
};
+ i2s1_clk: clk@01c200d8 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod1-clk";
+ reg = <0x01c200d8 0x4>;
+ clocks = <&pll2 SUN4I_A10_PLL2_8X>,
+ <&pll2 SUN4I_A10_PLL2_4X>,
+ <&pll2 SUN4I_A10_PLL2_2X>,
+ <&pll2 SUN4I_A10_PLL2_1X>;
+ clock-output-names = "i2s1";
+ };
+
+ i2s2_clk: clk@01c200dc {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-mod1-clk";
+ reg = <0x01c200dc 0x4>;
+ clocks = <&pll2 SUN4I_A10_PLL2_8X>,
+ <&pll2 SUN4I_A10_PLL2_4X>,
+ <&pll2 SUN4I_A10_PLL2_2X>,
+ <&pll2 SUN4I_A10_PLL2_1X>;
+ clock-output-names = "i2s2";
+ };
+
dram_gates: clk@01c20100 {
#clock-cells = <1>;
compatible = "allwinner,sun4i-a10-dram-gates-clk";
"dram_de_mp", "dram_ace";
};
+ de_be0_clk: clk@01c20104 {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-display-clk";
+ reg = <0x01c20104 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll5 1>;
+ clock-output-names = "de-be0";
+ };
+
+ de_be1_clk: clk@01c20108 {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-display-clk";
+ reg = <0x01c20108 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll5 1>;
+ clock-output-names = "de-be1";
+ };
+
+ de_fe0_clk: clk@01c2010c {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-display-clk";
+ reg = <0x01c2010c 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll5 1>;
+ clock-output-names = "de-fe0";
+ };
+
+ de_fe1_clk: clk@01c20110 {
+ #clock-cells = <0>;
+ #reset-cells = <0>;
+ compatible = "allwinner,sun4i-a10-display-clk";
+ reg = <0x01c20110 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll5 1>;
+ clock-output-names = "de-fe1";
+ };
+
+ tcon0_ch0_clk: clk@01c20118 {
+ #clock-cells = <0>;
+ #reset-cells = <1>;
+ compatible = "allwinner,sun4i-a10-tcon-ch0-clk";
+ reg = <0x01c20118 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+ clock-output-names = "tcon0-ch0-sclk";
+
+ };
+
+ tcon1_ch0_clk: clk@01c2011c {
+ #clock-cells = <0>;
+ #reset-cells = <1>;
+ compatible = "allwinner,sun4i-a10-tcon-ch1-clk";
+ reg = <0x01c2011c 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+ clock-output-names = "tcon1-ch0-sclk";
+
+ };
+
+ tcon0_ch1_clk: clk@01c2012c {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-tcon-ch0-clk";
+ reg = <0x01c2012c 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+ clock-output-names = "tcon0-ch1-sclk";
+
+ };
+
+ tcon1_ch1_clk: clk@01c20130 {
+ #clock-cells = <0>;
+ compatible = "allwinner,sun4i-a10-tcon-ch1-clk";
+ reg = <0x01c20130 0x4>;
+ clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
+ clock-output-names = "tcon1-ch1-sclk";
+
+ };
+
ve_clk: clk@01c2013c {
#clock-cells = <0>;
#reset-cells = <0>;
#dma-cells = <2>;
};
+ nfc: nand@01c03000 {
+ compatible = "allwinner,sun4i-a10-nand";
+ reg = <0x01c03000 0x1000>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ahb_gates 13>, <&nand_clk>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma SUN4I_DMA_DEDICATED 3>;
+ dma-names = "rxtx";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
spi0: spi@01c05000 {
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c05000 0x1000>;
};
mmc0: mmc@01c0f000 {
- compatible = "allwinner,sun5i-a13-mmc";
+ compatible = "allwinner,sun7i-a20-mmc",
+ "allwinner,sun5i-a13-mmc";
reg = <0x01c0f000 0x1000>;
clocks = <&ahb_gates 8>,
<&mmc0_clk 0>,
};
mmc1: mmc@01c10000 {
- compatible = "allwinner,sun5i-a13-mmc";
+ compatible = "allwinner,sun7i-a20-mmc",
+ "allwinner,sun5i-a13-mmc";
reg = <0x01c10000 0x1000>;
clocks = <&ahb_gates 9>,
<&mmc1_clk 0>,
};
mmc2: mmc@01c11000 {
- compatible = "allwinner,sun5i-a13-mmc";
+ compatible = "allwinner,sun7i-a20-mmc",
+ "allwinner,sun5i-a13-mmc";
reg = <0x01c11000 0x1000>;
clocks = <&ahb_gates 10>,
<&mmc2_clk 0>,
};
mmc3: mmc@01c12000 {
- compatible = "allwinner,sun5i-a13-mmc";
+ compatible = "allwinner,sun7i-a20-mmc",
+ "allwinner,sun5i-a13-mmc";
reg = <0x01c12000 0x1000>;
clocks = <&ahb_gates 11>,
<&mmc3_clk 0>,
#interrupt-cells = <3>;
#gpio-cells = <3>;
- pwm0_pins_a: pwm0@0 {
- allwinner,pins = "PB2";
- allwinner,function = "pwm";
+ clk_out_a_pins_a: clk_out_a@0 {
+ allwinner,pins = "PI12";
+ allwinner,function = "clk_out_a";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- pwm1_pins_a: pwm1@0 {
- allwinner,pins = "PI3";
- allwinner,function = "pwm";
+ clk_out_b_pins_a: clk_out_b@0 {
+ allwinner,pins = "PI13";
+ allwinner,function = "clk_out_b";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart0_pins_a: uart0@0 {
- allwinner,pins = "PB22", "PB23";
- allwinner,function = "uart0";
+ emac_pins_a: emac0@0 {
+ allwinner,pins = "PA0", "PA1", "PA2",
+ "PA3", "PA4", "PA5", "PA6",
+ "PA7", "PA8", "PA9", "PA10",
+ "PA11", "PA12", "PA13", "PA14",
+ "PA15", "PA16";
+ allwinner,function = "emac";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart2_pins_a: uart2@0 {
- allwinner,pins = "PI16", "PI17", "PI18", "PI19";
- allwinner,function = "uart2";
+ gmac_pins_mii_a: gmac_mii@0 {
+ allwinner,pins = "PA0", "PA1", "PA2",
+ "PA3", "PA4", "PA5", "PA6",
+ "PA7", "PA8", "PA9", "PA10",
+ "PA11", "PA12", "PA13", "PA14",
+ "PA15", "PA16";
+ allwinner,function = "gmac";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart3_pins_a: uart3@0 {
- allwinner,pins = "PG6", "PG7", "PG8", "PG9";
- allwinner,function = "uart3";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ gmac_pins_rgmii_a: gmac_rgmii@0 {
+ allwinner,pins = "PA0", "PA1", "PA2",
+ "PA3", "PA4", "PA5", "PA6",
+ "PA7", "PA8", "PA10",
+ "PA11", "PA12", "PA13",
+ "PA15", "PA16";
+ allwinner,function = "gmac";
+ /*
+ * data lines in RGMII mode use DDR mode
+ * and need a higher signal drive strength
+ */
+ allwinner,drive = <SUN4I_PINCTRL_40_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart3_pins_b: uart3@1 {
- allwinner,pins = "PH0", "PH1";
- allwinner,function = "uart3";
+ i2c0_pins_a: i2c0@0 {
+ allwinner,pins = "PB0", "PB1";
+ allwinner,function = "i2c0";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart4_pins_a: uart4@0 {
- allwinner,pins = "PG10", "PG11";
- allwinner,function = "uart4";
+ i2c1_pins_a: i2c1@0 {
+ allwinner,pins = "PB18", "PB19";
+ allwinner,function = "i2c1";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart4_pins_b: uart4@1 {
- allwinner,pins = "PH4", "PH5";
- allwinner,function = "uart4";
+ i2c2_pins_a: i2c2@0 {
+ allwinner,pins = "PB20", "PB21";
+ allwinner,function = "i2c2";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart5_pins_a: uart5@0 {
- allwinner,pins = "PI10", "PI11";
- allwinner,function = "uart5";
+ i2c3_pins_a: i2c3@0 {
+ allwinner,pins = "PI0", "PI1";
+ allwinner,function = "i2c3";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart6_pins_a: uart6@0 {
- allwinner,pins = "PI12", "PI13";
- allwinner,function = "uart6";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ ir0_rx_pins_a: ir0@0 {
+ allwinner,pins = "PB4";
+ allwinner,function = "ir0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart7_pins_a: uart7@0 {
- allwinner,pins = "PI20", "PI21";
- allwinner,function = "uart7";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ ir0_tx_pins_a: ir0@1 {
+ allwinner,pins = "PB3";
+ allwinner,function = "ir0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- i2c0_pins_a: i2c0@0 {
- allwinner,pins = "PB0", "PB1";
- allwinner,function = "i2c0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ ir1_rx_pins_a: ir1@0 {
+ allwinner,pins = "PB23";
+ allwinner,function = "ir1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- i2c1_pins_a: i2c1@0 {
- allwinner,pins = "PB18", "PB19";
- allwinner,function = "i2c1";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ ir1_tx_pins_a: ir1@1 {
+ allwinner,pins = "PB22";
+ allwinner,function = "ir1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- i2c2_pins_a: i2c2@0 {
- allwinner,pins = "PB20", "PB21";
- allwinner,function = "i2c2";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ mmc0_pins_a: mmc0@0 {
+ allwinner,pins = "PF0", "PF1", "PF2",
+ "PF3", "PF4", "PF5";
+ allwinner,function = "mmc0";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- i2c3_pins_a: i2c3@0 {
- allwinner,pins = "PI0", "PI1";
- allwinner,function = "i2c3";
+ mmc0_cd_pin_reference_design: mmc0_cd_pin@0 {
+ allwinner,pins = "PH1";
+ allwinner,function = "gpio_in";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ mmc2_pins_a: mmc2@0 {
+ allwinner,pins = "PC6", "PC7", "PC8",
+ "PC9", "PC10", "PC11";
+ allwinner,function = "mmc2";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ mmc3_pins_a: mmc3@0 {
+ allwinner,pins = "PI4", "PI5", "PI6",
+ "PI7", "PI8", "PI9";
+ allwinner,function = "mmc3";
+ allwinner,drive = <SUN4I_PINCTRL_30_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- emac_pins_a: emac0@0 {
- allwinner,pins = "PA0", "PA1", "PA2",
- "PA3", "PA4", "PA5", "PA6",
- "PA7", "PA8", "PA9", "PA10",
- "PA11", "PA12", "PA13", "PA14",
- "PA15", "PA16";
- allwinner,function = "emac";
+ ps20_pins_a: ps20@0 {
+ allwinner,pins = "PI20", "PI21";
+ allwinner,function = "ps2";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- clk_out_a_pins_a: clk_out_a@0 {
- allwinner,pins = "PI12";
- allwinner,function = "clk_out_a";
+ ps21_pins_a: ps21@0 {
+ allwinner,pins = "PH12", "PH13";
+ allwinner,function = "ps2";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- clk_out_b_pins_a: clk_out_b@0 {
- allwinner,pins = "PI13";
- allwinner,function = "clk_out_b";
+ pwm0_pins_a: pwm0@0 {
+ allwinner,pins = "PB2";
+ allwinner,function = "pwm";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- gmac_pins_mii_a: gmac_mii@0 {
- allwinner,pins = "PA0", "PA1", "PA2",
- "PA3", "PA4", "PA5", "PA6",
- "PA7", "PA8", "PA9", "PA10",
- "PA11", "PA12", "PA13", "PA14",
- "PA15", "PA16";
- allwinner,function = "gmac";
+ pwm1_pins_a: pwm1@0 {
+ allwinner,pins = "PI3";
+ allwinner,function = "pwm";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- gmac_pins_rgmii_a: gmac_rgmii@0 {
- allwinner,pins = "PA0", "PA1", "PA2",
- "PA3", "PA4", "PA5", "PA6",
- "PA7", "PA8", "PA10",
- "PA11", "PA12", "PA13",
- "PA15", "PA16";
- allwinner,function = "gmac";
- /*
- * data lines in RGMII mode use DDR mode
- * and need a higher signal drive strength
- */
- allwinner,drive = <SUN4I_PINCTRL_40_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ spdif_tx_pins_a: spdif@0 {
+ allwinner,pins = "PB13";
+ allwinner,function = "spdif";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
spi0_pins_a: spi0@0 {
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- mmc0_pins_a: mmc0@0 {
- allwinner,pins = "PF0", "PF1", "PF2",
- "PF3", "PF4", "PF5";
- allwinner,function = "mmc0";
- allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ uart0_pins_a: uart0@0 {
+ allwinner,pins = "PB22", "PB23";
+ allwinner,function = "uart0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- mmc0_cd_pin_reference_design: mmc0_cd_pin@0 {
- allwinner,pins = "PH1";
- allwinner,function = "gpio_in";
+ uart2_pins_a: uart2@0 {
+ allwinner,pins = "PI16", "PI17", "PI18", "PI19";
+ allwinner,function = "uart2";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-
- mmc2_pins_a: mmc2@0 {
- allwinner,pins = "PC6", "PC7", "PC8",
- "PC9", "PC10", "PC11";
- allwinner,function = "mmc2";
- allwinner,drive = <SUN4I_PINCTRL_30_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- mmc3_pins_a: mmc3@0 {
- allwinner,pins = "PI4", "PI5", "PI6",
- "PI7", "PI8", "PI9";
- allwinner,function = "mmc3";
- allwinner,drive = <SUN4I_PINCTRL_30_MA>;
+ uart3_pins_a: uart3@0 {
+ allwinner,pins = "PG6", "PG7", "PG8", "PG9";
+ allwinner,function = "uart3";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ir0_rx_pins_a: ir0@0 {
- allwinner,pins = "PB4";
- allwinner,function = "ir0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ uart3_pins_b: uart3@1 {
+ allwinner,pins = "PH0", "PH1";
+ allwinner,function = "uart3";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ir0_tx_pins_a: ir0@1 {
- allwinner,pins = "PB3";
- allwinner,function = "ir0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ uart4_pins_a: uart4@0 {
+ allwinner,pins = "PG10", "PG11";
+ allwinner,function = "uart4";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ir1_rx_pins_a: ir1@0 {
- allwinner,pins = "PB23";
- allwinner,function = "ir1";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ uart4_pins_b: uart4@1 {
+ allwinner,pins = "PH4", "PH5";
+ allwinner,function = "uart4";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ir1_tx_pins_a: ir1@1 {
- allwinner,pins = "PB22";
- allwinner,function = "ir1";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ uart5_pins_a: uart5@0 {
+ allwinner,pins = "PI10", "PI11";
+ allwinner,function = "uart5";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ps20_pins_a: ps20@0 {
- allwinner,pins = "PI20", "PI21";
- allwinner,function = "ps2";
+ uart6_pins_a: uart6@0 {
+ allwinner,pins = "PI12", "PI13";
+ allwinner,function = "uart6";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- ps21_pins_a: ps21@0 {
- allwinner,pins = "PH12", "PH13";
- allwinner,function = "ps2";
+ uart7_pins_a: uart7@0 {
+ allwinner,pins = "PI20", "PI21";
+ allwinner,function = "uart7";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
status = "disabled";
};
+ spdif: spdif@01c21000 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun4i-a10-spdif";
+ reg = <0x01c21000 0x400>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb0_gates 1>, <&spdif_clk>;
+ clock-names = "apb", "spdif";
+ dmas = <&dma SUN4I_DMA_NORMAL 2>,
+ <&dma SUN4I_DMA_NORMAL 2>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
ir0: ir@01c21800 {
compatible = "allwinner,sun4i-a10-ir";
clocks = <&apb0_gates 6>, <&ir0_clk>;
status = "disabled";
};
+ i2s1: i2s@01c22000 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun4i-a10-i2s";
+ reg = <0x01c22000 0x400>;
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb0_gates 4>, <&i2s1_clk>;
+ clock-names = "apb", "mod";
+ dmas = <&dma SUN4I_DMA_NORMAL 4>,
+ <&dma SUN4I_DMA_NORMAL 4>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ i2s0: i2s@01c22400 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun4i-a10-i2s";
+ reg = <0x01c22400 0x400>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb0_gates 3>, <&i2s0_clk>;
+ clock-names = "apb", "mod";
+ dmas = <&dma SUN4I_DMA_NORMAL 3>,
+ <&dma SUN4I_DMA_NORMAL 3>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
lradc: lradc@01c22800 {
compatible = "allwinner,sun4i-a10-lradc-keys";
reg = <0x01c22800 0x100>;
reg = <0x01c23800 0x200>;
};
+ i2s2: i2s@01c24400 {
+ #sound-dai-cells = <0>;
+ compatible = "allwinner,sun4i-a10-i2s";
+ reg = <0x01c24400 0x400>;
+ interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb0_gates 8>, <&i2s2_clk>;
+ clock-names = "apb", "mod";
+ dmas = <&dma SUN4I_DMA_NORMAL 6>,
+ <&dma SUN4I_DMA_NORMAL 6>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
rtp: rtp@01c25000 {
compatible = "allwinner,sun5i-a13-ts";
reg = <0x01c25000 0x100>;
};
mmc0: mmc@01c0f000 {
- compatible = "allwinner,sun5i-a13-mmc";
+ compatible = "allwinner,sun7i-a20-mmc",
+ "allwinner,sun5i-a13-mmc";
reg = <0x01c0f000 0x1000>;
clocks = <&ahb1_gates 8>,
<&mmc0_clk 0>,
};
mmc1: mmc@01c10000 {
- compatible = "allwinner,sun5i-a13-mmc";
+ compatible = "allwinner,sun7i-a20-mmc",
+ "allwinner,sun5i-a13-mmc";
reg = <0x01c10000 0x1000>;
clocks = <&ahb1_gates 9>,
<&mmc1_clk 0>,
};
mmc2: mmc@01c11000 {
- compatible = "allwinner,sun5i-a13-mmc";
+ compatible = "allwinner,sun7i-a20-mmc",
+ "allwinner,sun5i-a13-mmc";
reg = <0x01c11000 0x1000>;
clocks = <&ahb1_gates 10>,
<&mmc2_clk 0>,
/dts-v1/;
#include "sun8i-a23.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/pwm/pwm.h>
+#include "sun8i-reference-design-tablet.dtsi"
/ {
model = "Allwinner GT90H Dual Core Tablet (v4)";
compatible = "allwinner,gt90h-v4", "allwinner,sun8i-a23";
-
- aliases {
- serial0 = &r_uart;
- };
-
- backlight: backlight {
- compatible = "pwm-backlight";
- pinctrl-names = "default";
- pinctrl-0 = <&bl_en_pin_gt90h>;
- pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
- brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
- default-brightness-level = <8>;
- enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
};
&ehci0 {
status = "okay";
};
-&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-};
-
-&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
+&gsl1680 {
+ compatible = "silead,gsl3675";
+ touchscreen-fw-name = "silead/gsl3675-gt90h.fw";
+ touchscreen-size-x = <1792>;
+ touchscreen-size-y = <1024>;
status = "okay";
};
&lradc {
- vref-supply = <®_vcc3v0>;
- status = "okay";
-
- button@200 {
- label = "Volume Up";
- linux,code = <KEY_VOLUMEUP>;
- channel = <0>;
- voltage = <200000>;
- };
-
- button@400 {
- label = "Volume Down";
- linux,code = <KEY_VOLUMEDOWN>;
- channel = <0>;
- voltage = <400000>;
- };
-
button@600 {
label = "Back";
linux,code = <KEY_BACK>;
};
};
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_gt90h>;
- vmmc-supply = <®_aldo1>;
- bus-width = <4>;
- cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
- cd-inverted;
- status = "okay";
-};
-
-&pio {
- bl_en_pin_gt90h: bl_en_pin@0 {
- allwinner,pins = "PH6";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- mmc0_cd_pin_gt90h: mmc0_cd_pin@0 {
- allwinner,pins = "PB4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-};
-
-&pwm {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pins>;
- status = "okay";
-};
-
-&r_rsb {
- status = "okay";
-
- axp22x: pmic@3a3 {
- compatible = "x-powers,axp223";
- reg = <0x3a3>;
- interrupt-parent = <&nmi_intc>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- eldoin-supply = <®_dcdc1>;
- };
-};
-
-&r_uart {
- pinctrl-names = "default";
- pinctrl-0 = <&r_uart_pins_a>;
- status = "okay";
-};
-
-#include "axp22x.dtsi"
-
-®_aldo1 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-io";
-};
-
-®_aldo2 {
- regulator-always-on;
- regulator-min-microvolt = <2350000>;
- regulator-max-microvolt = <2650000>;
- regulator-name = "vdd-dll";
-};
-
-®_aldo3 {
- regulator-always-on;
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-pll-avcc";
-};
-
-®_dc1sw {
- regulator-name = "vcc-lcd";
-};
-
-®_dc5ldo {
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-cpus";
-};
-
-®_dcdc1 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-3v0";
-};
-
-®_dcdc2 {
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-sys";
-};
-
-®_dcdc3 {
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-cpu";
-};
-
-®_dcdc5 {
- regulator-always-on;
- regulator-min-microvolt = <1500000>;
- regulator-max-microvolt = <1500000>;
- regulator-name = "vcc-dram";
-};
-
-®_dldo1 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-wifi";
-};
-
-®_rtc_ldo {
- regulator-name = "vcc-rtc";
-};
-
-&simplefb_lcd {
- vcc-lcd-supply = <®_dc1sw>;
-};
-
-/*
- * FIXME for now we only support host mode and rely on u-boot to have
- * turned on Vbus which is controlled by the axp223 pmic on the board.
- *
- * Once we have axp223 support we should switch to fully supporting otg.
- */
-&usb_otg {
- dr_mode = "host";
- status = "okay";
-};
-
&usbphy {
usb1_vbus-supply = <®_dldo1>;
- status = "okay";
};
/dts-v1/;
#include "sun8i-a23.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/pwm/pwm.h>
+#include "sun8i-reference-design-tablet.dtsi"
/ {
model = "INet-86DZ Rev 01";
compatible = "primux,inet86dz", "allwinner,sun8i-a23";
-
- aliases {
- serial0 = &r_uart;
- };
-
- backlight: backlight {
- compatible = "pwm-backlight";
- pinctrl-names = "default";
- pinctrl-0 = <&bl_en_pin_inet86dz>;
- pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
- brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
- default-brightness-level = <8>;
- enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
};
&ehci0 {
status = "okay";
};
-&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
- /*
- * The gsl1680 is rated at 400KHz and it will not work reliable at
- * 100KHz, this has been confirmed on multiple different tablets.
- * The gsl1680 is the only device on this bus.
- */
- clock-frequency = <400000>;
-
- gsl1680: touchscreen@40 {
- compatible = "silead,gsl1680";
- reg = <0x40>;
- interrupt-parent = <&pio>;
- interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>; /* PB5 */
- pinctrl-names = "default";
- pinctrl-0 = <&ts_power_pin_inet86dz>;
- power-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- touchscreen-size-x = <960>;
- touchscreen-size-y = <640>;
- touchscreen-max-fingers = <5>;
- touchscreen-fw-name = "silead/gsl1680-inet86dz.fw";
- };
-};
-
-&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
- status = "okay";
-};
-
-&lradc {
- vref-supply = <®_vcc3v0>;
- status = "okay";
-
- button@200 {
- label = "Volume Up";
- linux,code = <KEY_VOLUMEUP>;
- channel = <0>;
- voltage = <200000>;
- };
-
- button@400 {
- label = "Volume Down";
- linux,code = <KEY_VOLUMEDOWN>;
- channel = <0>;
- voltage = <400000>;
- };
-};
-
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_inet86dz>;
- vmmc-supply = <®_dcdc1>;
- bus-width = <4>;
- cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
- cd-inverted;
- status = "okay";
-};
-
-&pio {
- bl_en_pin_inet86dz: bl_en_pin@0 {
- allwinner,pins = "PH6";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- mmc0_cd_pin_inet86dz: mmc0_cd_pin@0 {
- allwinner,pins = "PB4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-
- ts_power_pin_inet86dz: ts_power_pin@0 {
- allwinner,pins = "PH1";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PH8";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-};
-
-&pwm {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pins>;
- status = "okay";
-};
-
-&r_rsb {
- status = "okay";
-
- axp22x: pmic@3a3 {
- compatible = "x-powers,axp223";
- reg = <0x3a3>;
- interrupt-parent = <&nmi_intc>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- eldoin-supply = <®_dcdc1>;
- x-powers,drive-vbus-en;
- };
-};
-
-&r_uart {
- pinctrl-names = "default";
- pinctrl-0 = <&r_uart_pins_a>;
- status = "okay";
-};
-
-#include "axp22x.dtsi"
-
-®_aldo1 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-io";
-};
-
-®_aldo2 {
- regulator-always-on;
- regulator-min-microvolt = <2350000>;
- regulator-max-microvolt = <2650000>;
- regulator-name = "vdd-dll";
-};
-
-®_aldo3 {
- regulator-always-on;
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-pll-avcc";
-};
-
-®_dc1sw {
- regulator-name = "vcc-lcd";
-};
-
-®_dc5ldo {
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-cpus";
-};
-
-®_dcdc1 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-3v0";
-};
-
-®_dcdc2 {
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-sys";
-};
-
-®_dcdc3 {
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-cpu";
-};
-
-®_dcdc5 {
- regulator-always-on;
- regulator-min-microvolt = <1500000>;
- regulator-max-microvolt = <1500000>;
- regulator-name = "vcc-dram";
-};
-
-®_dldo1 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-wifi";
-};
-
-®_drivevbus {
- regulator-name = "usb0-vbus";
- status = "okay";
-};
-
-®_rtc_ldo {
- regulator-name = "vcc-rtc";
-};
-
-&simplefb_lcd {
- vcc-lcd-supply = <®_dc1sw>;
-};
-
-&usb_otg {
- dr_mode = "otg";
- status = "okay";
-};
-
-&usb_power_supply {
+&gsl1680 {
+ touchscreen-size-x = <960>;
+ touchscreen-size-y = <640>;
+ touchscreen-fw-name = "silead/gsl1680-inet86dz.fw";
status = "okay";
};
&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>;
- usb0_id_det-gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
- usb0_vbus_power-supply = <&usb_power_supply>;
- usb0_vbus-supply = <®_drivevbus>;
usb1_vbus-supply = <®_dldo1>;
- status = "okay";
};
/dts-v1/;
#include "sun8i-a23.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/pwm/pwm.h>
+#include "sun8i-reference-design-tablet.dtsi"
/ {
model = "Polaroid MID2407PXE03 tablet";
compatible = "polaroid,mid2407pxe03", "allwinner,sun8i-a23";
aliases {
- serial0 = &r_uart;
+ ethernet0 = &esp8089;
};
- backlight: backlight {
- compatible = "pwm-backlight";
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
pinctrl-names = "default";
- pinctrl-0 = <&bl_en_pin_mid2407>;
- pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
- brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
- default-brightness-level = <8>;
- enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
+ pinctrl-0 = <&wifi_pwrseq_pin_mid2407>;
+ reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL6 */
+ /* The esp8089 needs 200 ms after driving wifi-en high */
+ post-power-on-delay-ms = <200>;
};
};
-&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
+&gsl1680 {
+ vddio-supply = <®_ldo_io1>;
+ touchscreen-size-x = <960>;
+ touchscreen-size-y = <640>;
+ touchscreen-inverted-x;
+ touchscreen-inverted-y;
+ touchscreen-fw-name = "silead/gsl1680-polaroid-mid2407pxe03.fw";
status = "okay";
- /*
- * The gsl1680 is rated at 400KHz and it will not work reliable at
- * 100KHz, this has been confirmed on multiple different tablets.
- * The gsl1680 is the only device on this bus.
- */
- clock-frequency = <400000>;
-
- gsl1680: touchscreen@40 {
- compatible = "silead,gsl1680";
- reg = <0x40>;
- interrupt-parent = <&pio>;
- interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>; /* PB5 */
- pinctrl-names = "default";
- pinctrl-0 = <&ts_power_pin_mid2407>;
- power-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- touchscreen-size-x = <960>;
- touchscreen-size-y = <640>;
- touchscreen-inverted-x;
- touchscreen-inverted-y;
- touchscreen-max-fingers = <5>;
- touchscreen-fw-name = "silead/gsl1680-polaroid-mid2407pxe03.fw";
- };
};
-&i2c1 {
+&mmc1 {
pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
- status = "okay";
-};
-
-&lradc {
- vref-supply = <®_vcc3v0>;
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <®_dldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
status = "okay";
- button@200 {
- label = "Volume Up";
- linux,code = <KEY_VOLUMEUP>;
- channel = <0>;
- voltage = <200000>;
- };
-
- button@400 {
- label = "Volume Down";
- linux,code = <KEY_VOLUMEDOWN>;
- channel = <0>;
- voltage = <400000>;
+ esp8089: sdio_wifi@1 {
+ compatible = "esp,esp8089";
+ reg = <1>;
+ esp,crystal-26M-en = <2>;
};
};
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_mid2407>;
- vmmc-supply = <®_dcdc1>;
- bus-width = <4>;
- cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
- cd-inverted;
- status = "okay";
+&mmc1_pins_a {
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
-&pio {
- bl_en_pin_mid2407: bl_en_pin@0 {
- allwinner,pins = "PH6";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- mmc0_cd_pin_mid2407: mmc0_cd_pin@0 {
- allwinner,pins = "PB4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-
- ts_power_pin_mid2407: ts_power_pin@0 {
- allwinner,pins = "PH1";
+&r_pio {
+ wifi_pwrseq_pin_mid2407: wifi_pwrseq_pin@0 {
+ allwinner,pins = "PL6";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
-
- usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PH8";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-};
-
-&pwm {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pins>;
- status = "okay";
-};
-
-&r_rsb {
- status = "okay";
-
- axp22x: pmic@3a3 {
- compatible = "x-powers,axp223";
- reg = <0x3a3>;
- interrupt-parent = <&nmi_intc>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- eldoin-supply = <®_dcdc1>;
- x-powers,drive-vbus-en;
- };
-};
-
-&r_uart {
- pinctrl-names = "default";
- pinctrl-0 = <&r_uart_pins_a>;
- status = "okay";
-};
-
-#include "axp22x.dtsi"
-
-®_aldo1 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-io";
-};
-
-®_aldo2 {
- regulator-always-on;
- regulator-min-microvolt = <2350000>;
- regulator-max-microvolt = <2650000>;
- regulator-name = "vdd-dll";
-};
-
-®_aldo3 {
- regulator-always-on;
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-pll-avcc";
-};
-
-®_dc1sw {
- regulator-name = "vcc-lcd";
-};
-
-®_dc5ldo {
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-cpus";
-};
-
-®_dcdc1 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-3v0";
-};
-
-®_dcdc2 {
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-sys";
-};
-
-®_dcdc3 {
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-cpu";
-};
-
-®_dcdc5 {
- regulator-always-on;
- regulator-min-microvolt = <1500000>;
- regulator-max-microvolt = <1500000>;
- regulator-name = "vcc-dram";
-};
-
-®_drivevbus {
- regulator-name = "usb0-vbus";
- status = "okay";
};
®_ldo_io1 {
- regulator-always-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-touchscreen";
status = "okay";
};
-
-®_rtc_ldo {
- regulator-name = "vcc-rtc";
-};
-
-&simplefb_lcd {
- vcc-lcd-supply = <®_dc1sw>;
-};
-
-&usb_otg {
- dr_mode = "otg";
- status = "okay";
-};
-
-&usb_power_supply {
- status = "okay";
-};
-
-&usbphy {
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_id_detect_pin>;
- usb0_id_det-gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
- usb0_vbus_power-supply = <&usb_power_supply>;
- usb0_vbus-supply = <®_drivevbus>;
- status = "okay";
-};
/dts-v1/;
#include "sun8i-a23.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
-#include <dt-bindings/pwm/pwm.h>
+#include "sun8i-reference-design-tablet.dtsi"
/ {
model = "Polaroid MID2809PXE04 tablet";
compatible = "polaroid,mid2809pxe04", "allwinner,sun8i-a23";
aliases {
- serial0 = &r_uart;
+ ethernet0 = &esp8089;
};
- backlight: backlight {
- compatible = "pwm-backlight";
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
pinctrl-names = "default";
- pinctrl-0 = <&bl_en_pin_mid2809>;
- pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
- brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
- default-brightness-level = <8>;
- enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
+ pinctrl-0 = <&wifi_pwrseq_pin_mid2809>;
+ reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL6 */
+ /* The esp8089 needs 200 ms after driving wifi-en high */
+ post-power-on-delay-ms = <200>;
};
};
-&ehci0 {
- status = "okay";
-};
-
-&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
+&gsl1680 {
+ compatible = "silead,gsl3670";
+ touchscreen-fw-name = "silead/gsl3670-polaroid-mid2809pxe04.fw";
+ touchscreen-size-x = <1660>;
+ touchscreen-size-y = <890>;
status = "okay";
};
-&i2c1 {
+&mmc1 {
pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
- status = "okay";
-};
-
-&lradc {
- vref-supply = <®_vcc3v0>;
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <®_dldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
status = "okay";
- button@200 {
- label = "Volume Up";
- linux,code = <KEY_VOLUMEUP>;
- channel = <0>;
- voltage = <200000>;
- };
-
- button@400 {
- label = "Volume Down";
- linux,code = <KEY_VOLUMEDOWN>;
- channel = <0>;
- voltage = <400000>;
+ esp8089: sdio_wifi@1 {
+ compatible = "esp,esp8089";
+ reg = <1>;
+ esp,crystal-26M-en = <2>;
};
};
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_mid2809>;
- vmmc-supply = <®_dcdc1>;
- bus-width = <4>;
- cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
- cd-inverted;
- status = "okay";
+&mmc1_pins_a {
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
-&pio {
- bl_en_pin_mid2809: bl_en_pin@0 {
- allwinner,pins = "PH6";
- allwinner,function = "gpio_in";
+&r_pio {
+ wifi_pwrseq_pin_mid2809: wifi_pwrseq_pin@0 {
+ allwinner,pins = "PL6";
+ allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
-
- mmc0_cd_pin_mid2809: mmc0_cd_pin@0 {
- allwinner,pins = "PB4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-};
-
-&pwm {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm0_pins>;
- status = "okay";
-};
-
-&r_rsb {
- status = "okay";
-
- axp22x: pmic@3a3 {
- compatible = "x-powers,axp223";
- reg = <0x3a3>;
- interrupt-parent = <&nmi_intc>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- eldoin-supply = <®_dcdc1>;
- };
-};
-
-&r_uart {
- pinctrl-names = "default";
- pinctrl-0 = <&r_uart_pins_a>;
- status = "okay";
-};
-
-#include "axp22x.dtsi"
-
-®_aldo1 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-io";
-};
-
-®_aldo2 {
- regulator-always-on;
- regulator-min-microvolt = <2350000>;
- regulator-max-microvolt = <2650000>;
- regulator-name = "vdd-dll";
-};
-
-®_aldo3 {
- regulator-always-on;
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-pll-avcc";
-};
-
-®_dc1sw {
- regulator-name = "vcc-lcd";
-};
-
-®_dc5ldo {
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-cpus";
-};
-
-®_dcdc1 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-3v0";
-};
-
-®_dcdc2 {
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-sys";
-};
-
-®_dcdc3 {
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-cpu";
-};
-
-®_dcdc5 {
- regulator-always-on;
- regulator-min-microvolt = <1500000>;
- regulator-max-microvolt = <1500000>;
- regulator-name = "vcc-dram";
-};
-
-®_rtc_ldo {
- regulator-name = "vcc-rtc";
-};
-
-&simplefb_lcd {
- vcc-lcd-supply = <®_dc1sw>;
-};
-
-/*
- * FIXME for now we only support host mode and rely on u-boot to have
- * turned on Vbus which is controlled by the axp223 pmic on the board.
- *
- * Once we have axp223 support we should switch to fully supporting otg.
- */
-&usb_otg {
- dr_mode = "host";
- status = "okay";
-};
-
-&usbphy {
- status = "okay";
};
model = "Q8 A23 Tablet";
compatible = "allwinner,q8-a23", "allwinner,sun8i-a23";
};
-
-/*
- * FIXME for now we only support host mode and rely on u-boot to have
- * turned on Vbus which is controlled by the axp223 pmic on the board.
- *
- * Once we have axp223 support we should switch to fully supporting otg.
- */
-&usb_otg {
- dr_mode = "host";
- status = "okay";
-};
-
-&usbphy {
- status = "okay";
-};
/dts-v1/;
#include "sun8i-a33.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include "sun8i-reference-design-tablet.dtsi"
/ {
model = "Allwinner GA10H Quad Core Tablet (v1.1)";
compatible = "allwinner,ga10h-v1.1", "allwinner,sun8i-a33";
aliases {
- serial0 = &r_uart;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
+ /* Make u-boot set mac-address for rtl8703as (no eeprom) */
+ ethernet0 = &rtl8703as;
};
};
status = "okay";
};
-&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-};
-
-&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_a>;
+&gsl1680 {
+ compatible = "silead,gsl3675";
+ touchscreen-fw-name = "silead/gsl3675-ga10h.fw";
+ touchscreen-size-x = <1630>;
+ touchscreen-size-y = <990>;
+ touchscreen-inverted-y;
status = "okay";
};
&lradc {
- vref-supply = <®_vcc3v0>;
- status = "okay";
-
- button@200 {
- label = "Volume Up";
- linux,code = <KEY_VOLUMEUP>;
- channel = <0>;
- voltage = <200000>;
- };
-
- button@400 {
- label = "Volume Down";
- linux,code = <KEY_VOLUMEDOWN>;
- channel = <0>;
- voltage = <400000>;
- };
-
button@600 {
label = "Back";
linux,code = <KEY_BACK>;
};
};
-&mmc0 {
+&mmc1 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_q8h>;
- vmmc-supply = <®_vcc3v0>;
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <®_dldo1>;
bus-width = <4>;
- cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
- cd-inverted;
+ non-removable;
status = "okay";
-};
-&ohci0 {
- status = "okay";
-};
-
-&pio {
- mmc0_cd_pin_q8h: mmc0_cd_pin@0 {
- allwinner,pins = "PB4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ rtl8703as: sdio_wifi@1 {
+ reg = <1>;
};
};
-&r_uart {
- pinctrl-names = "default";
- pinctrl-0 = <&r_uart_pins_a>;
- status = "okay";
-};
-
-&usb_otg {
- dr_mode = "host";
- status = "okay";
-};
-
-&usbphy {
+&ohci0 {
status = "okay";
};
model = "Q8 A33 Tablet";
compatible = "allwinner,q8-a33", "allwinner,sun8i-a33";
};
-
-/*
- * FIXME for now we only support host mode and rely on u-boot to have
- * turned on Vbus which is controlled by the axp223 pmic on the board.
- *
- * Once we have axp223 support we should switch to fully supporting otg.
- */
-&usb_otg {
- dr_mode = "host";
- status = "okay";
-};
-
-&usbphy {
- status = "okay";
-};
--- /dev/null
+/*
+ * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Banana Pi BPI-M2-Plus";
+ compatible = "sinovoip,bpi-m2-plus", "allwinner,sun8i-h3";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwr_led_bpi_m2p>;
+
+ pwr_led {
+ label = "bananapi-m2-plus:red:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+ default-state = "on";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sw_r_bpi_m2p>;
+
+ sw4 {
+ label = "power";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_en_bpi_m2p>;
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ };
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcmf: bcrmf@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&r_pio {
+ pwr_led_bpi_m2p: led_pins@0 {
+ allwinner,pins = "PL10";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ sw_r_bpi_m2p: key_pins@0 {
+ allwinner,pins = "PL3";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ wifi_en_bpi_m2p: wifi_en_pin {
+ allwinner,pins = "PL7";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins_a>;
+ status = "okay";
+};
+
+&usbphy {
+ /* USB VBUS is on as long as VCC-IO is on */
+ status = "okay";
+};
aliases {
serial0 = &uart0;
+ /* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+ ethernet1 = &rtl8189;
};
chosen {
bus-width = <4>;
non-removable;
status = "okay";
+
+ /*
+ * Explicitly define the sdio device, so that we can add an ethernet
+ * alias for it (which e.g. makes u-boot set a mac-address).
+ */
+ rtl8189: sdio_wifi@1 {
+ reg = <1>;
+ };
};
&pio {
usb1_vbus-supply = <®_usb1_vbus>;
status = "okay";
};
-
-&emac {
- pinctrl-names = "default";
- pinctrl-0 = <&rgmii_pins>;
- phy-mode = "rgmii";
- phy = <&phy1>;
- status = "okay";
-
- phy1: ethernet-phy@1 {
- reg = <1>;
- };
-};
-
aliases {
/* The H3 emac is not used so the wifi is ethernet0 */
- ethernet1 = &rtl8189ftv;
+ ethernet0 = &rtl8189ftv;
serial0 = &uart0;
};
#include "sun8i-h3-orangepi-pc.dts"
/ {
- model = "Xunlong Orange Pi PC / PC Plus";
+ model = "Xunlong Orange Pi PC Plus";
+ compatible = "xunlong,orangepi-pc-plus", "allwinner,sun8i-h3";
aliases {
/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
- pinctrl-0 = <&leds_opc>;
+ pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
- status_led {
- label = "status:red:user";
- gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>;
- };
- };
-
- r_leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&leds_r_opc>;
-
- tx {
- label = "pwr:green:user";
+ pwr_led {
+ label = "orangepi:green:pwr";
gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
+
+ status_led {
+ label = "orangepi:red:status";
+ gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>;
+ };
};
r_gpio_keys {
compatible = "gpio-keys";
- input-name = "sw4";
-
pinctrl-names = "default";
pinctrl-0 = <&sw_r_opc>;
- sw4@0 {
+ sw4 {
label = "sw4";
linux,code = <BTN_0>;
gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
};
sw_r_opc: key_pins@0 {
- allwinner,pins = "PL03";
+ allwinner,pins = "PL3";
allwinner,function = "gpio_in";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
&emac {
phy = <&phy1>;
phy-mode = "mii";
- allwinner,use-internal-phy;
allwinner,leds-active-low;
status = "okay";
-
phy1: ethernet-phy@1 {
reg = <1>;
};
enable-active-high;
gpio = <&pio 6 11 GPIO_ACTIVE_HIGH>;
};
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_power_pin_orangepi>;
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
+ };
};
&ehci2 {
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
+
+ gmac_power_pin_orangepi: gmac_power_pin@0 {
+ allwinner,pins = "PD6";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
};
&usbphy {
usb3_vbus-supply = <®_usb3_vbus>;
};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+
+ allwinner,leds-active-low;
+ status = "okay";
+
+ phy1: ethernet-phy@1 {
+ reg = <0>;
+ };
+};
#include "skeleton.dtsi"
+#include <dt-bindings/clock/sun8i-h3-ccu.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/reset/sun8i-h3-ccu.h>
/ {
interrupt-parent = <&gic>;
aliases {
- ethernet0 = <&emac>;
+ ethernet0 = &emac;
};
cpus {
clock-output-names = "osc32k";
};
- pll1: clk@01c20000 {
- #clock-cells = <0>;
- compatible = "allwinner,sun8i-a23-pll1-clk";
- reg = <0x01c20000 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll1";
- };
-
- /* dummy clock until actually implemented */
- pll5: pll5_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <0>;
- clock-output-names = "pll5";
- };
-
- pll6: clk@01c20028 {
- #clock-cells = <1>;
- compatible = "allwinner,sun6i-a31-pll6-clk";
- reg = <0x01c20028 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll6", "pll6x2";
- };
-
- pll6d2: pll6d2_clk {
- #clock-cells = <0>;
- compatible = "fixed-factor-clock";
- clock-div = <2>;
- clock-mult = <1>;
- clocks = <&pll6 0>;
- clock-output-names = "pll6d2";
- };
-
- /* dummy clock until pll6 can be reused */
- pll8: pll8_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <1>;
- clock-output-names = "pll8";
- };
-
- cpu: cpu_clk@01c20050 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-cpu-clk";
- reg = <0x01c20050 0x4>;
- clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
- clock-output-names = "cpu";
- };
-
- axi: axi_clk@01c20050 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-axi-clk";
- reg = <0x01c20050 0x4>;
- clocks = <&cpu>;
- clock-output-names = "axi";
- };
-
- ahb1: ahb1_clk@01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun6i-a31-ahb1-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
- clock-output-names = "ahb1";
- };
-
- ahb2: ahb2_clk@01c2005c {
- #clock-cells = <0>;
- compatible = "allwinner,sun8i-h3-ahb2-clk";
- reg = <0x01c2005c 0x4>;
- clocks = <&ahb1>, <&pll6d2>;
- clock-output-names = "ahb2";
- };
-
- apb1: apb1_clk@01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-apb0-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&ahb1>;
- clock-output-names = "apb1";
- };
-
- apb2: apb2_clk@01c20058 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-apb1-clk";
- reg = <0x01c20058 0x4>;
- clocks = <&osc32k>, <&osc24M>, <&pll6 0>, <&pll6 0>;
- clock-output-names = "apb2";
- };
-
- bus_gates: clk@01c20060 {
- #clock-cells = <1>;
- compatible = "allwinner,sun8i-h3-bus-gates-clk";
- reg = <0x01c20060 0x14>;
- clocks = <&ahb1>, <&ahb2>, <&apb1>, <&apb2>;
- clock-names = "ahb1", "ahb2", "apb1", "apb2";
- clock-indices = <5>, <6>, <8>,
- <9>, <10>, <13>,
- <14>, <17>, <18>,
- <19>, <20>,
- <21>, <23>,
- <24>, <25>,
- <26>, <27>,
- <28>, <29>,
- <30>, <31>, <32>,
- <35>, <36>, <37>,
- <40>, <41>, <43>,
- <44>, <52>, <53>,
- <54>, <64>,
- <65>, <69>, <72>,
- <76>, <77>, <78>,
- <96>, <97>, <98>,
- <112>, <113>,
- <114>, <115>,
- <116>, <128>, <135>;
- clock-output-names = "bus_ce", "bus_dma", "bus_mmc0",
- "bus_mmc1", "bus_mmc2", "bus_nand",
- "bus_sdram", "bus_gmac", "bus_ts",
- "bus_hstimer", "bus_spi0",
- "bus_spi1", "bus_otg",
- "bus_otg_ehci0", "bus_ehci1",
- "bus_ehci2", "bus_ehci3",
- "bus_otg_ohci0", "bus_ohci1",
- "bus_ohci2", "bus_ohci3", "bus_ve",
- "bus_lcd0", "bus_lcd1", "bus_deint",
- "bus_csi", "bus_tve", "bus_hdmi",
- "bus_de", "bus_gpu", "bus_msgbox",
- "bus_spinlock", "bus_codec",
- "bus_spdif", "bus_pio", "bus_ths",
- "bus_i2s0", "bus_i2s1", "bus_i2s2",
- "bus_i2c0", "bus_i2c1", "bus_i2c2",
- "bus_uart0", "bus_uart1",
- "bus_uart2", "bus_uart3",
- "bus_scr", "bus_ephy", "bus_dbg";
- };
-
- mmc0_clk: clk@01c20088 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c20088 0x4>;
- clocks = <&osc24M>, <&pll6 0>, <&pll8>;
- clock-output-names = "mmc0",
- "mmc0_output",
- "mmc0_sample";
- };
-
- mmc1_clk: clk@01c2008c {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c2008c 0x4>;
- clocks = <&osc24M>, <&pll6 0>, <&pll8>;
- clock-output-names = "mmc1",
- "mmc1_output",
- "mmc1_sample";
- };
-
- mmc2_clk: clk@01c20090 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c20090 0x4>;
- clocks = <&osc24M>, <&pll6 0>, <&pll8>;
- clock-output-names = "mmc2",
- "mmc2_output",
- "mmc2_sample";
- };
-
- usb_clk: clk@01c200cc {
- #clock-cells = <1>;
- #reset-cells = <1>;
- compatible = "allwinner,sun8i-h3-usb-clk";
- reg = <0x01c200cc 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "usb_phy0", "usb_phy1",
- "usb_phy2", "usb_phy3",
- "usb_ohci0", "usb_ohci1",
- "usb_ohci2", "usb_ohci3";
- };
-
- mbus_clk: clk@01c2015c {
- #clock-cells = <0>;
- compatible = "allwinner,sun8i-a23-mbus-clk";
- reg = <0x01c2015c 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5>;
- clock-output-names = "mbus";
- };
-
apb0: apb0_clk {
compatible = "fixed-factor-clock";
#clock-cells = <0>;
#size-cells = <1>;
ranges;
+ syscon: syscon@01c00000 {
+ compatible = "allwinner,sun8i-h3-syscon","syscon";
+ reg = <0x01c00000 0x34>;
+ };
+
dma: dma-controller@01c02000 {
compatible = "allwinner,sun8i-h3-dma";
reg = <0x01c02000 0x1000>;
interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&bus_gates 6>;
- resets = <&ahb_rst 6>;
+ clocks = <&ccu CLK_BUS_DMA>;
+ resets = <&ccu RST_BUS_DMA>;
#dma-cells = <1>;
};
mmc0: mmc@01c0f000 {
- compatible = "allwinner,sun5i-a13-mmc";
+ compatible = "allwinner,sun7i-a20-mmc",
+ "allwinner,sun5i-a13-mmc";
reg = <0x01c0f000 0x1000>;
- clocks = <&bus_gates 8>,
- <&mmc0_clk 0>,
- <&mmc0_clk 1>,
- <&mmc0_clk 2>;
+ clocks = <&ccu CLK_BUS_MMC0>,
+ <&ccu CLK_MMC0>,
+ <&ccu CLK_MMC0_OUTPUT>,
+ <&ccu CLK_MMC0_SAMPLE>;
clock-names = "ahb",
"mmc",
"output",
"sample";
- resets = <&ahb_rst 8>;
+ resets = <&ccu RST_BUS_MMC0>;
reset-names = "ahb";
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
mmc1: mmc@01c10000 {
- compatible = "allwinner,sun5i-a13-mmc";
+ compatible = "allwinner,sun7i-a20-mmc",
+ "allwinner,sun5i-a13-mmc";
reg = <0x01c10000 0x1000>;
- clocks = <&bus_gates 9>,
- <&mmc1_clk 0>,
- <&mmc1_clk 1>,
- <&mmc1_clk 2>;
+ clocks = <&ccu CLK_BUS_MMC1>,
+ <&ccu CLK_MMC1>,
+ <&ccu CLK_MMC1_OUTPUT>,
+ <&ccu CLK_MMC1_SAMPLE>;
clock-names = "ahb",
"mmc",
"output",
"sample";
- resets = <&ahb_rst 9>;
+ resets = <&ccu RST_BUS_MMC1>;
reset-names = "ahb";
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
};
mmc2: mmc@01c11000 {
- compatible = "allwinner,sun5i-a13-mmc";
+ compatible = "allwinner,sun7i-a20-mmc",
+ "allwinner,sun5i-a13-mmc";
reg = <0x01c11000 0x1000>;
- clocks = <&bus_gates 10>,
- <&mmc2_clk 0>,
- <&mmc2_clk 1>,
- <&mmc2_clk 2>;
+ clocks = <&ccu CLK_BUS_MMC2>,
+ <&ccu CLK_MMC2>,
+ <&ccu CLK_MMC2_OUTPUT>,
+ <&ccu CLK_MMC2_SAMPLE>;
clock-names = "ahb",
"mmc",
"output",
"sample";
- resets = <&ahb_rst 10>;
+ resets = <&ccu RST_BUS_MMC2>;
reset-names = "ahb";
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
"pmu1",
"pmu2",
"pmu3";
- clocks = <&usb_clk 8>,
- <&usb_clk 9>,
- <&usb_clk 10>,
- <&usb_clk 11>;
+ clocks = <&ccu CLK_USB_PHY0>,
+ <&ccu CLK_USB_PHY1>,
+ <&ccu CLK_USB_PHY2>,
+ <&ccu CLK_USB_PHY3>;
clock-names = "usb0_phy",
"usb1_phy",
"usb2_phy",
"usb3_phy";
- resets = <&usb_clk 0>,
- <&usb_clk 1>,
- <&usb_clk 2>,
- <&usb_clk 3>;
+ resets = <&ccu RST_USB_PHY0>,
+ <&ccu RST_USB_PHY1>,
+ <&ccu RST_USB_PHY2>,
+ <&ccu RST_USB_PHY3>;
reset-names = "usb0_reset",
"usb1_reset",
"usb2_reset",
compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
reg = <0x01c1b000 0x100>;
interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&bus_gates 25>, <&bus_gates 29>;
- resets = <&ahb_rst 25>, <&ahb_rst 29>;
+ clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
+ resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
reg = <0x01c1b400 0x100>;
interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&bus_gates 29>, <&bus_gates 25>,
- <&usb_clk 17>;
- resets = <&ahb_rst 29>, <&ahb_rst 25>;
+ clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
+ <&ccu CLK_USB_OHCI1>;
+ resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
reg = <0x01c1c000 0x100>;
interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&bus_gates 26>, <&bus_gates 30>;
- resets = <&ahb_rst 26>, <&ahb_rst 30>;
+ clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
+ resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
phys = <&usbphy 2>;
phy-names = "usb";
status = "disabled";
compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
reg = <0x01c1c400 0x100>;
interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&bus_gates 30>, <&bus_gates 26>,
- <&usb_clk 18>;
- resets = <&ahb_rst 30>, <&ahb_rst 26>;
+ clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
+ <&ccu CLK_USB_OHCI2>;
+ resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
phys = <&usbphy 2>;
phy-names = "usb";
status = "disabled";
compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
reg = <0x01c1d000 0x100>;
interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&bus_gates 27>, <&bus_gates 31>;
- resets = <&ahb_rst 27>, <&ahb_rst 31>;
+ clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
+ resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
phys = <&usbphy 3>;
phy-names = "usb";
status = "disabled";
compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
reg = <0x01c1d400 0x100>;
interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&bus_gates 31>, <&bus_gates 27>,
- <&usb_clk 19>;
- resets = <&ahb_rst 31>, <&ahb_rst 27>;
+ clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
+ <&ccu CLK_USB_OHCI3>;
+ resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
phys = <&usbphy 3>;
phy-names = "usb";
status = "disabled";
};
+ ccu: clock@01c20000 {
+ compatible = "allwinner,sun8i-h3-ccu";
+ reg = <0x01c20000 0x400>;
+ clocks = <&osc24M>, <&osc32k>;
+ clock-names = "hosc", "losc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
pio: pinctrl@01c20800 {
compatible = "allwinner,sun8i-h3-pinctrl";
reg = <0x01c20800 0x400>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&bus_gates 69>;
+ clocks = <&ccu CLK_BUS_PIO>;
gpio-controller;
#gpio-cells = <3>;
interrupt-controller;
#interrupt-cells = <3>;
- rgmii_pins: rgmii_pins {
+ emac_rgmii_pins: emac0@0 {
allwinner,pins = "PD0", "PD1", "PD2", "PD3",
- "PD4", "PD5", "PD7",
- "PD8", "PD9", "PD10",
- "PD12", "PD13", "PD15",
- "PD16", "PD17";
+ "PD4", "PD5", "PD7",
+ "PD8", "PD9", "PD10",
+ "PD12", "PD13", "PD15",
+ "PD16", "PD17";
allwinner,function = "emac";
allwinner,drive = <SUN4I_PINCTRL_40_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- uart0_pins_a: uart0@0 {
- allwinner,pins = "PA4", "PA5";
- allwinner,function = "uart0";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
mmc0_pins_a: mmc0@0 {
allwinner,pins = "PF0", "PF1", "PF2", "PF3",
"PF4", "PF5";
allwinner,drive = <SUN4I_PINCTRL_30_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
- };
- ahb_rst: reset@01c202c0 {
- #reset-cells = <1>;
- compatible = "allwinner,sun6i-a31-ahb1-reset";
- reg = <0x01c202c0 0xc>;
- };
-
- apb1_rst: reset@01c202d0 {
- #reset-cells = <1>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- reg = <0x01c202d0 0x4>;
- };
+ uart0_pins_a: uart0@0 {
+ allwinner,pins = "PA4", "PA5";
+ allwinner,function = "uart0";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
- apb2_rst: reset@01c202d8 {
- #reset-cells = <1>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- reg = <0x01c202d8 0x4>;
+ uart1_pins_a: uart1@0 {
+ allwinner,pins = "PG6", "PG7", "PG8", "PG9";
+ allwinner,function = "uart1";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
};
timer@01c20c00 {
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&bus_gates 112>;
- resets = <&apb2_rst 16>;
+ clocks = <&ccu CLK_BUS_UART0>;
+ resets = <&ccu RST_BUS_UART0>;
dmas = <&dma 6>, <&dma 6>;
dma-names = "rx", "tx";
status = "disabled";
interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&bus_gates 113>;
- resets = <&apb2_rst 17>;
+ clocks = <&ccu CLK_BUS_UART1>;
+ resets = <&ccu RST_BUS_UART1>;
dmas = <&dma 7>, <&dma 7>;
dma-names = "rx", "tx";
status = "disabled";
interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&bus_gates 114>;
- resets = <&apb2_rst 18>;
+ clocks = <&ccu CLK_BUS_UART2>;
+ resets = <&ccu RST_BUS_UART2>;
dmas = <&dma 8>, <&dma 8>;
dma-names = "rx", "tx";
status = "disabled";
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&bus_gates 115>;
- resets = <&apb2_rst 19>;
+ clocks = <&ccu CLK_BUS_UART3>;
+ resets = <&ccu RST_BUS_UART3>;
dmas = <&dma 9>, <&dma 9>;
dma-names = "rx", "tx";
status = "disabled";
};
- emac: ethernet@01c30000 {
+ emac: ethernet@1c30000 {
compatible = "allwinner,sun8i-h3-emac";
- reg = <0x01c30000 0x2000>, <0x01c00030 0x4>;
- reg-names = "emac", "syscon";
+ syscon = <&syscon>;
+ reg = <0x01c30000 0x104>;
+ reg-names = "emac";
interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
- resets = <&ahb_rst 17>, <&ahb_rst 66>;
+ resets = <&ccu RST_BUS_EMAC>, <&ccu RST_BUS_EPHY>;
reset-names = "ahb", "ephy";
- clocks = <&bus_gates 17>, <&bus_gates 128>;
+ clocks = <&ccu CLK_BUS_EMAC>, <&ccu CLK_BUS_EPHY>;
clock-names = "ahb", "ephy";
#address-cells = <1>;
#size-cells = <0>;
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "sunxi-q8-common.dtsi"
-
-#include <dt-bindings/pwm/pwm.h>
+#include "sunxi-reference-design-tablet.dtsi"
+#include "sun8i-reference-design-tablet.dtsi"
/ {
aliases {
serial0 = &r_uart;
+ /* Make u-boot set mac-address for wifi without an eeprom */
+ ethernet0 = &sdio_wifi;
};
- backlight: backlight {
- compatible = "pwm-backlight";
- pinctrl-names = "default";
- pinctrl-0 = <&bl_en_pin_q8>;
- pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
- brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
- default-brightness-level = <8>;
- enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+ q8_hardwaremgr {
+ compatible = "allwinner,sunxi-q8-hardwaremgr";
+ touchscreen-i2c-bus = <&i2c0>;
+ touchscreen-supply = <®_ldo_io1>;
+ touchscreen-power-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
};
- chosen {
- stdout-path = "serial0:115200n8";
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ /*
+ * Q8 boards use various PL# pins as wifi-en. On other boards
+ * these may be connected to a wifi module output pin. To avoid
+ * short-circuits we configure these as inputs with pull-ups via
+ * pinctrl, instead of listing them as active-low reset-gpios.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_pwrseq_pin_q8>;
+ /* The esp8089 needs 200 ms after driving wifi-en high */
+ post-power-on-delay-ms = <200>;
};
};
-&mmc0 {
+&ehci0 {
+ status = "okay";
+};
+
+&mmc1 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_q8>;
- vmmc-supply = <®_dcdc1>;
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <®_dldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
- cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
- cd-inverted;
+ non-removable;
status = "okay";
-};
-&pio {
- bl_en_pin_q8: bl_en_pin@0 {
- allwinner,pins = "PH6";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ sdio_wifi: sdio_wifi@1 {
+ reg = <1>;
};
+};
- mmc0_cd_pin_q8: mmc0_cd_pin@0 {
- allwinner,pins = "PB4";
+&mmc1_pins_a {
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
+&r_pio {
+ wifi_pwrseq_pin_q8: wifi_pwrseq_pin@0 {
+ allwinner,pins = "PL6", "PL7", "PL11";
allwinner,function = "gpio_in";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
};
-&r_rsb {
- status = "okay";
-
- axp22x: pmic@3a3 {
- compatible = "x-powers,axp223";
- reg = <0x3a3>;
- interrupt-parent = <&nmi_intc>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- eldoin-supply = <®_dcdc1>;
- };
+&usbphy {
+ usb1_vbus-supply = <®_dldo1>;
};
-#include "axp22x.dtsi"
-
-®_aldo1 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-io";
-};
-
-®_aldo2 {
- regulator-always-on;
- regulator-min-microvolt = <2350000>;
- regulator-max-microvolt = <2650000>;
- regulator-name = "vdd-dll";
+&gsl1680 {
+ touchscreen-size-x = <1024>;
+ touchscreen-size-y = <600>;
+ touchscreen-fw-name = "silead/gsl1680-q8-700.fw";
+ status = "okay";
};
-®_aldo3 {
- regulator-always-on;
- regulator-min-microvolt = <2700000>;
+®_ldo_io1 {
+ regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-pll-avcc";
-};
-
-®_dc1sw {
- regulator-name = "vcc-lcd";
-};
-
-®_dc5ldo {
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-cpus";
-};
-
-®_dcdc1 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-3v0";
-};
-
-®_dcdc2 {
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-sys";
-};
-
-®_dcdc3 {
- regulator-always-on;
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-cpu";
-};
-
-®_dcdc5 {
- regulator-always-on;
- regulator-min-microvolt = <1500000>;
- regulator-max-microvolt = <1500000>;
- regulator-name = "vcc-dram";
-};
-
-®_rtc_ldo {
- regulator-name = "vcc-rtc";
-};
-
-&r_uart {
- pinctrl-names = "default";
- pinctrl-0 = <&r_uart_pins_a>;
+ regulator-name = "vcc-touchscreen";
status = "okay";
};
-
-&simplefb_lcd {
- vcc-lcd-supply = <®_dc1sw>;
-};
pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
- /* FIXME: An as-yet-unknown accelerometer is connected to this i2c bus. */
+ /*
+ * FIXME: An as-yet-unknown accelerometer is connected to this
+ * i2c bus.
+ */
};
&lradc {
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include "sunxi-reference-design-tablet.dtsi"
+
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ aliases {
+ serial0 = &r_uart;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&bl_en_pin>;
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <8>;
+ enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&i2c0 {
+ /*
+ * The gsl1680 is rated at 400KHz and it will not work reliable at
+ * 100KHz, this has been confirmed on multiple different q8 tablets.
+ * The gsl1680 is the only device on this bus.
+ */
+ clock-frequency = <400000>;
+
+ gsl1680: touchscreen@40 {
+ compatible = "silead,gsl1680";
+ reg = <0x40>;
+ interrupt-parent = <&pio>;
+ interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>; /* PB5 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_power_pin>;
+ power-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ /* Most tablets use this touchscreen, but not all */
+ status = "disabled";
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
+ cd-inverted;
+ status = "okay";
+};
+
+&pio {
+ bl_en_pin: bl_en_pin@0 {
+ allwinner,pins = "PH6";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin: mmc0_cd_pin@0 {
+ allwinner,pins = "PB4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ ts_power_pin: ts_power_pin@0 {
+ allwinner,pins = "PH1";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PH8";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp22x: pmic@3a3 {
+ compatible = "x-powers,axp223";
+ reg = <0x3a3>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ eldoin-supply = <®_dcdc1>;
+ drivevbus-supply = <®_vcc5v0>;
+ x-powers,drive-vbus-en;
+ };
+};
+
+#include "axp22x.dtsi"
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-io";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <2350000>;
+ regulator-max-microvolt = <2650000>;
+ regulator-name = "vdd-dll";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dc1sw {
+ regulator-name = "vcc-lcd";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
+&r_uart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_uart_pins_a>;
+ status = "okay";
+};
+
+&simplefb_lcd {
+ vcc-lcd-supply = <®_dc1sw>;
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb0_vbus-supply = <®_drivevbus>;
+ status = "okay";
+};
/dts-v1/;
#include "sun9i-a80.dtsi"
-#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
};
};
-&pio {
- led_pins_cubieboard4: led-pins@0 {
- allwinner,pins = "PH6", "PH17";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- mmc0_cd_pin_cubieboard4: mmc0_cd_pin@0 {
- allwinner,pins = "PH18";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-};
-
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_cubieboard4>;
- vmmc-supply = <®_vcc3v0>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH18 */
cd-inverted;
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_8bit_pins>;
- vmmc-supply = <®_vcc3v0>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <8>;
non-removable;
cap-mmc-hw-reset;
allwinner,drive = <SUN4I_PINCTRL_40_MA>;
};
+&pio {
+ led_pins_cubieboard4: led-pins@0 {
+ allwinner,pins = "PH6", "PH17";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin_cubieboard4: mmc0_cd_pin@0 {
+ allwinner,pins = "PH18";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+};
+
&r_ir {
status = "okay";
};
&r_rsb {
status = "okay";
+
+ axp809: pmic@3a3 {
+ reg = <0x3a3>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ reg_aldo1: aldo1 {
+ /*
+ * TODO: This should be handled by the
+ * USB PHY driver.
+ */
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc33-usbh";
+ };
+
+ reg_aldo2: aldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pb-io-cam";
+ };
+
+ aldo3 {
+ /* unused */
+ };
+
+ reg_dc5ldo: dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus-09-usbh";
+ };
+
+ reg_dcdc1: dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v";
+ };
+
+ reg_dcdc2: dcdc2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-gpu";
+ };
+
+ reg_dcdc3: dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpua";
+ };
+
+ reg_dcdc4: dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-sys-usb0-hdmi";
+ };
+
+ reg_dcdc5: dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1425000>;
+ regulator-max-microvolt = <1575000>;
+ regulator-name = "vcc-dram";
+ };
+
+ reg_dldo1: dldo1 {
+ /*
+ * The WiFi chip supports a wide range
+ * (3.0 ~ 4.8V) of voltages, and so does
+ * this regulator (3.0 ~ 4.2V), but
+ * Allwinner SDK always sets it to 3.3V.
+ */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+ };
+
+ reg_dldo2: dldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pl";
+ };
+
+ reg_eldo1: eldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-dvdd-cam";
+ };
+
+ reg_eldo2: eldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pe";
+ };
+
+ reg_eldo3: eldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pm-codec-io1";
+ };
+
+ reg_ldo_io0: ldo_io0 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pg";
+ };
+
+ reg_ldo_io1: ldo_io1 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "vcc-pa-gmac-2v5";
+ };
+
+ reg_rtc_ldo: rtc_ldo {
+ regulator-name = "vcc-rtc-vdd1v8-io";
+ };
+ };
+ };
};
+#include "axp809.dtsi"
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
/dts-v1/;
#include "sun9i-a80.dtsi"
-#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
};
};
+ reg_usb1_vbus: usb1-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb1_vbus_pin_optimus>;
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ };
+
reg_usb3_vbus: usb3-vbus {
compatible = "regulator-fixed";
pinctrl-names = "default";
status = "okay";
};
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_optimus>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH8 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&mmc2_8bit_pins {
+ /* Increase drive strength for DDR modes */
+ allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+};
+
&ohci0 {
status = "okay";
};
};
};
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_optimus>;
- vmmc-supply = <®_vcc3v0>;
- bus-width = <4>;
- cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH8 */
- cd-inverted;
- status = "okay";
-};
-
-&mmc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_8bit_pins>;
- vmmc-supply = <®_vcc3v0>;
- bus-width = <8>;
- non-removable;
- cap-mmc-hw-reset;
- status = "okay";
-};
-
-&mmc2_8bit_pins {
- /* Increase drive strength for DDR modes */
- allwinner,drive = <SUN4I_PINCTRL_40_MA>;
-};
-
-®_usb1_vbus {
- pinctrl-0 = <&usb1_vbus_pin_optimus>;
- gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
- status = "okay";
-};
-
&r_ir {
status = "okay";
};
&r_rsb {
status = "okay";
+
+ axp809: pmic@3a3 {
+ reg = <0x3a3>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ reg_aldo1: aldo1 {
+ /*
+ * TODO: This should be handled by the
+ * USB PHY driver.
+ */
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc33-usbh";
+ };
+
+ reg_aldo2: aldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pb-io-cam";
+ };
+
+ aldo3 {
+ /* unused */
+ };
+
+ reg_dc5ldo: dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus-09-usbh";
+ };
+
+ reg_dcdc1: dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v";
+ };
+
+ reg_dcdc2: dcdc2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-gpu";
+ };
+
+ reg_dcdc3: dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpua";
+ };
+
+ reg_dcdc4: dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-sys-usb0-hdmi";
+ };
+
+ reg_dcdc5: dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1425000>;
+ regulator-max-microvolt = <1575000>;
+ regulator-name = "vcc-dram";
+ };
+
+ reg_dldo1: dldo1 {
+ /*
+ * The WiFi chip supports a wide range
+ * (3.0 ~ 4.8V) of voltages, and so does
+ * this regulator (3.0 ~ 4.2V), but
+ * Allwinner SDK always sets it to 3.3V.
+ */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+ };
+
+ reg_dldo2: dldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pl";
+ };
+
+ reg_eldo1: eldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-dvdd-cam";
+ };
+
+ reg_eldo2: eldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pe";
+ };
+
+ reg_eldo3: eldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pm-codec-io1";
+ };
+
+ reg_ldo_io0: ldo_io0 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pg";
+ };
+
+ reg_ldo_io1: ldo_io1 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "vcc-pa-gmac-2v5";
+ };
+
+ reg_rtc_ldo: rtc_ldo {
+ regulator-name = "vcc-rtc-vdd1v8-io";
+ };
+ };
+ };
};
+#include "axp809.dtsi"
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
--- /dev/null
+/*
+ * Copyright 2015 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include "sunxi-common-regulators.dtsi"
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&lradc {
+ vref-supply = <®_vcc3v0>;
+ status = "okay";
+
+ button@200 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <200000>;
+ };
+
+ button@400 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <400000>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pins>;
+ status = "okay";
+};
#define _ARMD1_CONFIG_H
#include <asm/arch/armada100.h>
-/* default Dcache Line length for armada100 */
-#define CONFIG_SYS_CACHELINE_SIZE 32
#define CONFIG_SYS_TCLK (14745600) /* NS16550 clk config */
#define CONFIG_SYS_HZ_CLOCK (3250000) /* Timer Freq. 3.25MHZ */
#define CONFIG_SYS_FSL_SRDS_1
#define CONFIG_SYS_FSL_SRDS_2
#define CONFIG_SYS_PAGE_SIZE 0x10000
-#define CONFIG_SYS_CACHELINE_SIZE 64
#ifndef L1_CACHE_BYTES
#define L1_CACHE_SHIFT 6
#define L1_CACHE_BYTES BIT(L1_CACHE_SHIFT)
#define CONFIG_SYS_FSL_MAX_NUM_OF_SEC 1
#elif defined(CONFIG_FSL_LSCH2)
-#define CONFIG_SYS_CACHELINE_SIZE 64
#define CONFIG_NUM_DDR_CONTROLLERS 1
#define CONFIG_SYS_FSL_SEC_COMPAT 5
#define CONFIG_SYS_FSL_OCRAM_BASE 0x10000000 /* initial RAM */
#ifndef _ASM_ARMV7_LS102XA_CONFIG_
#define _ASM_ARMV7_LS102XA_CONFIG_
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#define OCRAM_BASE_ADDR 0x10000000
#define OCRAM_SIZE 0x00010000
#define OCRAM_BASE_S_ADDR 0x10010000
#define ARCH_MXC
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#if defined(CONFIG_MX51)
#define IRAM_BASE_ADDR 0x1FFE0000 /* internal ram */
#define IPU_SOC_BASE_ADDR 0x40000000
#define ARCH_MXC
-#ifdef CONFIG_MX6UL
-#define CONFIG_SYS_CACHELINE_SIZE 64
-#else
-#define CONFIG_SYS_CACHELINE_SIZE 32
-#endif
-
#define ROMCP_ARB_BASE_ADDR 0x00000000
#define ROMCP_ARB_END_ADDR 0x000FFFFF
#define ARCH_MXC
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#define ROM_SW_INFO_ADDR 0x000001E8
#define ROMCP_ARB_BASE_ADDR 0x00000000
#define ROMCP_ARB_END_ADDR 0x00017FFF
u32 mipi_bias_cfg; /* 0x240 MIPI Bias config */
u32 pll9_bias_cfg; /* 0x244 PLL9 Bias config */
u32 pll10_bias_cfg; /* 0x248 PLL10 Bias config */
- u32 reserved21[13];
+ u32 reserved21[5];
+ u32 pll5_tuning_cfg; /* 0x260 PLL5 Tuning config */
+ u32 reserved21_5[7];
u32 pll1_pattern_cfg; /* 0x280 PLL1 Pattern config */
u32 pll2_pattern_cfg; /* 0x284 PLL2 Pattern config */
u32 pll3_pattern_cfg; /* 0x288 PLL3 Pattern config */
#define CCM_PLL11_CTRL_UPD (0x1 << 30)
#define CCM_PLL11_CTRL_EN (0x1 << 31)
+#define CCM_PLL5_TUN_LOCK_TIME(x) (((x) & 0x7) << 24)
+#define CCM_PLL5_TUN_LOCK_TIME_MASK CCM_PLL5_TUN_LOCK_TIME(0x7)
+#define CCM_PLL5_TUN_INIT_FREQ(x) (((x) & 0x7f) << 16)
+#define CCM_PLL5_TUN_INIT_FREQ_MASK CCM_PLL5_TUN_INIT_FREQ(0x7f)
+
#if defined(CONFIG_MACH_SUN50I)
/* AHB1=100MHz failsafe setup from the FEL mode, usable with PMIC defaults */
#define AHB1_ABP1_DIV_DEFAULT 0x00003190 /* AHB1=PLL6/6,APB1=AHB1/2 */
#define SUNXI_INTC_BASE 0x01c20400
#define SUNXI_PIO_BASE 0x01c20800
#define SUNXI_TIMER_BASE 0x01c20c00
+#ifndef CONFIG_SUNXI_GEN_SUN6I
+#define SUNXI_PWM_BASE 0x01c20e00
+#endif
#define SUNXI_SPDIF_BASE 0x01c21000
+#ifdef CONFIG_SUNXI_GEN_SUN6I
+#define SUNXI_PWM_BASE 0x01c21400
+#else
#define SUNXI_AC97_BASE 0x01c21400
+#endif
#define SUNXI_IR0_BASE 0x01c21800
#define SUNXI_IR1_BASE 0x01c21c00
#define SUN6I_GPA_SDC3 4
#define SUN8I_H3_GPA_UART0 2
+#define SUN4I_GPB_PWM 2
#define SUN4I_GPB_TWI0 2
#define SUN4I_GPB_TWI1 2
#define SUN5I_GPB_TWI1 2
#define SUN6I_GPG_TWI3 2
#define SUN5I_GPG_UART1 4
+#define SUN6I_GPH_PWM 2
+#define SUN8I_GPH_PWM 2
#define SUN4I_GPH_SDC1 5
#define SUN6I_GPH_TWI0 2
#define SUN8I_GPH_TWI0 2
--- /dev/null
+/*
+ * (C) Copyright 2016 Hans de Goede <hdegoede@redhat.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _SUNXI_PWM_H
+#define _SUNXI_PWM_H
+
+#define SUNXI_PWM_CTRL_REG (SUNXI_PWM_BASE + 0)
+#define SUNXI_PWM_CH0_PERIOD (SUNXI_PWM_BASE + 4)
+
+#define SUNXI_PWM_CTRL_PRESCALE0(x) ((x) & 0xf)
+#define SUNXI_PWM_CTRL_ENABLE0 (0x5 << 4)
+#define SUNXI_PWM_CTRL_POLARITY0(x) ((x) << 5)
+
+#define SUNXI_PWM_PERIOD_80PCT 0x04af03c0
+
+#if defined CONFIG_MACH_SUN4I || defined CONFIG_MACH_SUN5I
+#define SUNXI_PWM_PIN0 SUNXI_GPB(2)
+#define SUNXI_PWM_MUX SUN4I_GPB_PWM
+#endif
+
+#if defined CONFIG_MACH_SUN6I
+#define SUNXI_PWM_PIN0 SUNXI_GPH(13)
+#define SUNXI_PWM_MUX SUN6I_GPH_PWM
+#endif
+
+#if defined CONFIG_MACH_SUN8I_A23 || defined CONFIG_MACH_SUN8I_A33
+#define SUNXI_PWM_PIN0 SUNXI_GPH(0)
+#define SUNXI_PWM_MUX SUN8I_GPH_PWM
+#endif
+
+#endif
#endif
/*
- * The current upper bound for ARM L1 data cache line sizes is 64 bytes. We
- * use that value for aligning DMA buffers unless the board config has specified
- * an alternate cache line size.
+ * The value of the largest data cache relevant to DMA operations shall be set
+ * for us in CONFIG_SYS_CACHELINE_SIZE. In some cases this may be a larger
+ * value than found in the L1 cache but this is OK to use in terms of
+ * alignment.
*/
-#ifdef CONFIG_SYS_CACHELINE_SIZE
#define ARCH_DMA_MINALIGN CONFIG_SYS_CACHELINE_SIZE
-#else
-#define ARCH_DMA_MINALIGN 64
-#endif
#endif /* _ASM_CACHE_H */
void mmu_set_region_dcache_behaviour(phys_addr_t start, size_t size,
enum dcache_option option)
{
+#ifdef CONFIG_ARMV7_LPAE
+ u64 *page_table = (u64 *)gd->arch.tlb_addr;
+#else
u32 *page_table = (u32 *)gd->arch.tlb_addr;
+#endif
+ unsigned long startpt, stoppt;
unsigned long upto, end;
end = ALIGN(start + size, MMU_SECTION_SIZE) >> MMU_SECTION_SHIFT;
option);
for (upto = start; upto < end; upto++)
set_section_dcache(upto, option);
- mmu_page_table_flush((u32)&page_table[start], (u32)&page_table[end]);
+
+ /*
+ * Make sure range is cache line aligned
+ * Only CPU maintains page tables, hence it is safe to always
+ * flush complete cache lines...
+ */
+
+ startpt = (unsigned long)&page_table[start];
+ startpt &= ~(CONFIG_SYS_CACHELINE_SIZE - 1);
+ stoppt = (unsigned long)&page_table[end];
+ stoppt = ALIGN(stoppt, CONFIG_SYS_CACHELINE_SIZE);
+ mmu_page_table_flush(startpt, stoppt);
}
__weak void dram_bank_mmu_setup(int bank)
#include <common.h>
#include <malloc.h>
-#ifndef CONFIG_SYS_CACHELINE_SIZE
-#define CONFIG_SYS_CACHELINE_SIZE 32
-#endif
-
/*
* Flush range from all levels of d-cache/unified-cache.
* Affects the range [start, start + size - 1].
#endif /* CONFIG_KW88F6281 */
#include <asm/arch/soc.h>
-#define CONFIG_SYS_CACHELINE_SIZE 32
- /* default Dcache Line length for kirkwood */
#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
#define MV88F78X60 /* for the DDR training bin_hdr code */
#endif
-#define CONFIG_SYS_CACHELINE_SIZE 32
-
#define CONFIG_SYS_L2_PL310
#ifdef CONFIG_SPL_BUILD
const int max_n = 32;
int k = 1, m = 2;
+#ifdef CONFIG_MACH_SUN8I_H3
+ clrsetbits_le32(&ccm->pll5_tuning_cfg, CCM_PLL5_TUN_LOCK_TIME_MASK |
+ CCM_PLL5_TUN_INIT_FREQ_MASK,
+ CCM_PLL5_TUN_LOCK_TIME(2) | CCM_PLL5_TUN_INIT_FREQ(16));
+#endif
+
if (sigma_delta_enable)
writel(CCM_PLL5_PATTERN, &ccm->pll5_pattern_cfg);
config CACHE_UNIPHIER
bool "Enable the UniPhier L2 cache controller"
depends on ARCH_UNIPHIER_32BIT
+ select SYS_CACHE_SHIFT_7
default y
help
This option allows to use the UniPhier System Cache as L2 cache.
U_BOOT_CMD(
ddrm, 2, 1, do_ddrm,
"UniPhier DDR PHY parameters dumper",
- "- dump all of the followings\n"
+ "- dump all of the following\n"
"ddrm zq - dump Impedance Data\n"
"ddrm wbdl - dump Write Bit Delay\n"
"ddrm rbdl - dump Read Bit Delay\n"
U_BOOT_CMD(
ddr, 2, 1, do_ddr,
"UniPhier DDR PHY parameters dumper",
- "- dump all of the followings\n"
+ "- dump all of the following\n"
"ddr wbdl - dump Write Bit Delay\n"
"ddr rbdl - dump Read Bit Delay\n"
"ddr wld - dump Write Leveling\n"
----------------------------
The X-QSGMII-16PORT is a 4xQSGMII/8xSGMII riser card with eighth SerDes
interfaces implemented in PCIe form factor board.
-It supports followings
+It supports following:
- Card can operate with up to 4 QSGMII lane simultaneously
- Card can operate with up to 8 SGMII lane simultaneously
F: configs/CHIP_defconfig
F: configs/difrnce_dit4350_defconfig
F: configs/Empire_electronix_d709_defconfig
+F: configs/Empire_electronix_m712_defconfig
F: configs/inet98v_rev2_defconfig
F: configs/mk802_a10s_defconfig
F: configs/q8_a13_tablet_defconfig
F: include/configs/sun6i.h
F: configs/colorfly_e708_q1_defconfig
F: configs/CSQ_CS908_defconfig
+F: configs/inet_q972_defconfig
F: configs/Mele_A1000G_quad_defconfig
F: configs/Mele_M9_defconfig
F: configs/Sinovoip_BPI_M2_defconfig
static int set_dev(int dev)
{
- if (dev < 0 || dev >= CONFIG_SYS_MAX_NAND_DEVICE ||
- !nand_info[dev]->name) {
+ if (dev < 0 || dev >= CONFIG_SYS_MAX_NAND_DEVICE || !nand_info[dev]) {
puts("No such device\n");
return -1;
}
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN5I=y
+CONFIG_DRAM_CLK=408
+CONFIG_MMC0_CD_PIN="PG0"
+CONFIG_USB0_VBUS_PIN="PG12"
+CONFIG_USB0_VBUS_DET="PG1"
+CONFIG_USB0_ID_DET="PG2"
+CONFIG_AXP_GPIO=y
+# CONFIG_VIDEO_HDMI is not set
+CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:45,ri:82,up:22,lo:22,hs:1,vs:1,sync:3,vmode:0"
+CONFIG_VIDEO_LCD_POWER="AXP0-0"
+CONFIG_VIDEO_LCD_BL_EN="AXP0-1"
+CONFIG_VIDEO_LCD_BL_PWM="PB2"
+CONFIG_DEFAULT_DEVICE_TREE="sun5i-a13-empire-electronix-m712"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=2"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_USB_MUSB_HOST=y
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_FPGA is not set
CONFIG_AXP_DLDO1_VOLT=3300
+# CONFIG_REQUIRE_SERIAL_CONSOLE is not set
CONFIG_USB_MUSB_HOST=y
CONFIG_VIDEO_LCD_SSD2828_TX_CLK=27
CONFIG_VIDEO_LCD_SSD2828_RESET="PA26"
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN6I=y
+CONFIG_DRAM_CLK=384
+CONFIG_DRAM_ZQ=251
+CONFIG_MMC0_CD_PIN="PA8"
+CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
+CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_USB0_ID_DET="PA15"
+CONFIG_AXP_GPIO=y
+CONFIG_VIDEO_LCD_MODE="x:1024,y:768,depth:18,pclk_khz:65000,le:280,ri:20,up:22,lo:8,hs:20,vs:8,sync:3,vmode:0"
+CONFIG_VIDEO_LCD_DCLK_PHASE=0
+CONFIG_VIDEO_LCD_BL_EN="PA25"
+CONFIG_VIDEO_LCD_BL_PWM="PH13"
+CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31s-inet-q972"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_AXP_DLDO1_VOLT=3300
+CONFIG_USB_MUSB_HOST=y
+CONFIG_USB_EHCI_HCD=y
- silentoldconfig
This target updates .config, include/generated/autoconf.h and
- include/configs/* as in Linux. In U-Boot, it also does the followings
+ include/configs/* as in Linux. In U-Boot, it also does the following
for the compatibility with the old configuration system:
* create a symbolic link "arch/${ARCH}/include/asm/arch" pointing to
#include <asm/arch/clock.h>
#include <asm/arch/display.h>
#include <asm/arch/gpio.h>
+#include <asm/arch/pwm.h>
#include <asm/global_data.h>
#include <asm/gpio.h>
#include <asm/io.h>
gpio_direction_output(pin, 1);
pin = sunxi_name_to_gpio(CONFIG_VIDEO_LCD_BL_PWM);
+#ifdef SUNXI_PWM_PIN0
+ if (pin == SUNXI_PWM_PIN0) {
+ writel(SUNXI_PWM_CTRL_POLARITY0(PWM_ON) |
+ SUNXI_PWM_CTRL_ENABLE0 |
+ SUNXI_PWM_CTRL_PRESCALE0(0xf), SUNXI_PWM_CTRL_REG);
+ writel(SUNXI_PWM_PERIOD_80PCT, SUNXI_PWM_CH0_PERIOD);
+ sunxi_gpio_set_cfgpin(pin, SUNXI_PWM_MUX);
+ return;
+ }
+#endif
if (pin >= 0)
gpio_direction_output(pin, PWM_ON);
}
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
/*
* High Level Configuration Options
*/
#define CONFIG_OMAP
#define CONFIG_OMAP_COMMON
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#define CONFIG_SYS_NO_FLASH
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define CONFIG_BOARD_LATE_INIT
#define CONFIG_ARCH_CPU_INIT
-#define CONFIG_SYS_CACHELINE_SIZE 32
#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 21) /* 2GB */
#define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */
/* Enabling L2 Cache */
#define CONFIG_SYS_L2_PL310
#define CONFIG_SYS_PL310_BASE 0x48242000
-#define CONFIG_SYS_CACHELINE_SIZE 32
/*
* Since SPL did pll and ddr initialization for us,
#include <asm/hardware.h>
-#define CONFIG_SYS_CACHELINE_SIZE 32
-
#define CONFIG_SYS_TEXT_BASE 0x26f00000
/* ARM asynchronous clock */
/* Commands */
#define CONFIG_FAT_WRITE
-#define CONFIG_SYS_CACHELINE_SIZE 64
#undef CONFIG_USB_GADGET_VBUS_DRAW
#define CONFIG_USB_GADGET_VBUS_DRAW 0
#define CONFIG_USBID_ADDR 0x34052c46
/* Commands */
#define CONFIG_FAT_WRITE
-#define CONFIG_SYS_CACHELINE_SIZE 64
#define CONFIG_USBID_ADDR 0x34052c46
#endif /* __BCM28155_AP_H */
#define CONFIG_SKIP_LOWLEVEL_INIT
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
/*
* Memory configuration
* (these must be defined elsewhere)
#define CONFIG_AM33XX
#define CONFIG_OMAP
#define CONFIG_OMAP_COMMON
-#define CONFIG_SYS_CACHELINE_SIZE 64
#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */
/* Timer information */
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
/*
* High Level Configuration Options
*/
* Although the default iss 64, we still define it
* to be on the safe side once the default is changed.
*/
-#define CONFIG_SYS_CACHELINE_SIZE 64
#define CONFIG_EMIF4 /* The chip has EMIF4 controller */
/* Enabling L2 Cache */
#define CONFIG_SYS_L2_PL310
#define CONFIG_SYS_PL310_BASE 0x48242000
-#define CONFIG_SYS_CACHELINE_SIZE 32
/*
* Since SPL did pll and ddr initialization for us,
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_SYS_CACHELINE_SIZE 32
-
#include <asm/arch/imx-regs.h>
#define CONFIG_VF610
#define CONFIG_SYS_NO_FLASH
-#define CONFIG_SYS_CACHELINE_SIZE 32
-
/* USB Host Support */
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_VF
#define CONFIG_SYS_DFU_DATA_BUF_SIZE (SZ_1M)
#define DFU_MANIFEST_POLL_TIMEOUT 25000
-#define CONFIG_SYS_CACHELINE_SIZE SZ_8K
#define CONFIG_SYS_LOAD_ADDR ATMEL_BASE_CS6
/* bootstrap + u-boot + env in nandflash */
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x80000)
#define CONFIG_SYS_BOOTM_LEN 0x1000000 /* 16MB max kernel size */
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
/* UART */
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOARD_COMMON
-#define CONFIG_SYS_CACHELINE_SIZE 32
#define CONFIG_REVISION_TAG
/* SD/MMC configuration */
#include "exynos-common.h"
-#define CONFIG_SYS_CACHELINE_SIZE 64
#define CONFIG_EXYNOS_SPL
#ifdef FTRACE
#define CONFIG_MX35
#define CONFIG_SYS_DCACHE_OFF
-#define CONFIG_SYS_CACHELINE_SIZE 32
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_SUPPORT_RAW_INITRD
-/* MMU Definitions */
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#define CONFIG_IDENT_STRING "hikey"
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_SYS_L2_PL310 1
#define CONFIG_SYS_PL310_BASE 0x48242000
-#define CONFIG_SYS_CACHELINE_SIZE 32
/*
* Platform
#undef DEBUG
-#define CONFIG_SYS_CACHELINE_SIZE 32
-
#define CONFIG_SH73A0
#define CONFIG_KZM_A9_GT
#define CONFIG_ARCH_RMOBILE_BOARD_STRING "KMC KZM-A9-GT"
#define CONFIG_MACH_TYPE MACH_TYPE_MCX
#define CONFIG_BOARD_LATE_INIT
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#define CONFIG_EMIF4 /* The chip has EMIF4 controller */
#include <asm/arch/cpu.h> /* get chip and board defs */
#define CONFIG_CPU_ARMV8
#define CONFIG_REMAKE_ELF
-#define CONFIG_SYS_CACHELINE_SIZE 64
#define CONFIG_SYS_NO_FLASH
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_ENV_IS_NOWHERE 1
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
/*
* High Level Configuration Options
*/
#define CONFIG_OMAP3_SPI
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
/* Defines for SPL */
#define CONFIG_SPL_OMAP3_ID_NAND
#define CONFIG_OMAP3_SPI
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
/* Defines for SPL */
#define CONFIG_SPL_OMAP3_ID_NAND
/* Uncomment to define the board revision statically */
/* #define CONFIG_STATIC_BOARD_REV OMAP3EVM_BOARD_GEN_2 */
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
/* Defines for SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE 0x40200800
#define CONFIG_ANDROID_BOOT_IMAGE
#define CONFIG_FASTBOOT_BUF_ADDR CONFIG_SYS_LOAD_ADDR
#define CONFIG_FASTBOOT_BUF_SIZE 0x07000000
-#define CONFIG_SYS_CACHELINE_SIZE 64
/* TWL4030 */
#define CONFIG_TWL4030_PWM
/* Initial RAM setup */
#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
#define CONFIG_SYS_INIT_RAM_SIZE 0x800
-#define CONFIG_SYS_CACHELINE_SIZE 64
/* NAND boot config */
#define CONFIG_SYS_NAND_BUSWIDTH_16BIT
#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#endif /* __CONFIG_H */
#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#ifdef CONFIG_CMD_NET
/* Ethernet (LAN9211 from SMSC9118 family) */
#define CONFIG_SMC911X
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_SYS_CACHELINE_SIZE 32
-
#include <asm/arch/imx-regs.h>
#define CONFIG_VF610
#ifndef __RCAR_GEN2_COMMON_H
#define __RCAR_GEN2_COMMON_H
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#include <asm/arch/rmobile.h>
#define CONFIG_CMD_DFL
#ifndef __CONFIG_RK3036_COMMON_H
#define __CONFIG_RK3036_COMMON_H
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#include <asm/arch/hardware.h>
#define CONFIG_SYS_NO_FLASH
#ifndef __CONFIG_RK3288_COMMON_H
#define __CONFIG_RK3288_COMMON_H
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#include <asm/arch/hardware.h>
#define CONFIG_SYS_NO_FLASH
#ifndef __CONFIG_RK3399_COMMON_H
#define __CONFIG_RK3399_COMMON_H
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#define CONFIG_SYS_NO_FLASH
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_SKIP_LOWLEVEL_INIT
#endif
-#ifdef CONFIG_BCM2835
-#define CONFIG_SYS_CACHELINE_SIZE 32
-#else
-#define CONFIG_SYS_CACHELINE_SIZE 64
-#endif
-
/* Architecture, CPU, etc.*/
#define CONFIG_ARCH_CPU_INIT
#define CONFIG_S5PC110 1 /* which is in a S5PC110 */
#define CONFIG_MACH_GONI 1 /* working with Goni */
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#include <linux/sizes.h>
#include <asm/arch/cpu.h> /* get chip and board defs */
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - 0x1000000)
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#define CONFIG_POWER
#define CONFIG_POWER_I2C
#define CONFIG_POWER_MAX8998
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
/* commands to include */
#define CONFIG_ENV_VARS_UBOOT_CONFIG
#define CONFIG_DFU_NAND
#define CONFIG_SYS_DFU_DATA_BUF_SIZE SZ_1M
#define DFU_MANIFEST_POLL_TIMEOUT 25000
-
-#define CONFIG_SYS_CACHELINE_SIZE 0x2000
#endif
/* General Boot Parameter */
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
/*
* High Level Configuration Options
* (easy to change)
* CPU
*/
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#define CONFIG_ARM_ARCH_CP15_ERRATA
#define CONFIG_ARM_ERRATA_454179
#define CONFIG_ARM_ERRATA_430973
/*
* Cache
*/
-#define CONFIG_SYS_CACHELINE_SIZE 32
#define CONFIG_SYS_L2_PL310
#define CONFIG_SYS_PL310_BASE SOCFPGA_MPUL2_ADDRESS
/* CPU */
#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_SYS_CACHELINE_SIZE 64
#define CONFIG_TIMER_CLK_FREQ 24000000
/*
#define CONFIG_SYS_TEXT_BASE 0x80008000
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#define CONFIG_EMIF4 /* The chip has EMIF4 controller */
#include <asm/arch/cpu.h> /* get chip and board defs */
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
/*
* High Level Configuration Options
*/
#define CONFIG_DFU_NAND
#define CONFIG_SYS_DFU_DATA_BUF_SIZE (SZ_1M)
#define DFU_MANIFEST_POLL_TIMEOUT 25000
-
-#define CONFIG_SYS_CACHELINE_SIZE SZ_8K
#endif
/* SPI EEPROM */
#define _TEGRA114_COMMON_H_
#include "tegra-common.h"
-/* Cortex-A15 uses a cache line size of 64 bytes */
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
/*
* NS16550 Configuration
*/
#include "tegra-common.h"
-/* Cortex-A15 uses a cache line size of 64 bytes */
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
/*
* NS16550 Configuration
*/
#include "tegra-common.h"
-/* Cortex-A57 uses a cache line size of 64 bytes */
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
/*
* NS16550 Configuration
*/
#define _TEGRA20_COMMON_H_
#include "tegra-common.h"
-/* Cortex-A9 uses a cache line size of 32 bytes */
-#define CONFIG_SYS_CACHELINE_SIZE 32
-
/*
* Errata configuration
*/
#include "tegra-common.h"
-/* Cortex-A57 uses a cache line size of 64 bytes */
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
/*
* NS16550 Configuration
*/
#define _TEGRA30_COMMON_H_
#include "tegra-common.h"
-/* Cortex-A9 uses a cache line size of 32 bytes */
-#define CONFIG_SYS_CACHELINE_SIZE 32
-
/*
* Errata configuration
*/
#ifndef __CONFIG_TI814X_EVM_H
#define __CONFIG_TI814X_EVM_H
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#define CONFIG_TI81XX
#define CONFIG_TI814X
#define CONFIG_SYS_NO_FLASH
#ifndef __CONFIG_TI816X_EVM_H
#define __CONFIG_TI816X_EVM_H
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#define CONFIG_TI81XX
#define CONFIG_TI816X
#define CONFIG_SYS_NO_FLASH
#define CONFIG_AM33XX
#define CONFIG_ARCH_CPU_INIT
-#define CONFIG_SYS_CACHELINE_SIZE 64
#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */
#define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */
#define CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
#define CONFIG_USB_STORAGE
#define CONFIG_EFI_PARTITION
#define CONFIG_FS_FAT
-#define CONFIG_SYS_CACHELINE_SIZE 64
#define CONFIG_USB_SS_BASE KS2_USB_SS_BASE
#define CONFIG_USB_HOST_XHCI_BASE KS2_USB_HOST_XHCI_BASE
#define CONFIG_DEV_USB_PHY_BASE KS2_DEV_USB_PHY_BASE
* High Level Configuration Options
*/
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#include <asm/arch/cpu.h>
#include <asm/arch/omap.h>
#define CONFIG_SYS_L2_PL310 1
#define CONFIG_SYS_PL310_BASE 0x48242000
#endif
-#define CONFIG_SYS_CACHELINE_SIZE 32
/* Get CPU defs */
#include <asm/arch/cpu.h>
/* Common ARM Erratas */
#define CONFIG_ARM_ERRATA_798870
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
/* Use General purpose timer 1 */
#define CONFIG_SYS_TIMERBASE GPT2_BASE
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
/* High Level Configuration Options */
#define CONFIG_SYS_THUMB_BUILD
#define CONFIG_OMAP /* in a TI OMAP core */
/* #define CONFIG_SYS_ICACHE_OFF */
/* #define CONFIG_SYS_DCACHE_OFF */
-#ifdef CONFIG_CACHE_UNIPHIER
-#define CONFIG_SYS_CACHELINE_SIZE 128
-#else
-#define CONFIG_SYS_CACHELINE_SIZE 32
-#endif
-
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
#define CONFIG_MISC_INIT_F
#define CONFIG_SUPPORT_RAW_INITRD
-/* MMU Definitions */
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#define CONFIG_IDENT_STRING " vexpress_aemv8a"
/* Link Definitions */
#define CONFIG_SYS_MEMTEST_START V2M_BASE
#define CONFIG_SYS_MEMTEST_END 0x20000000
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS 1
#define CONFIG_SYS_L2CACHE_OFF 1
#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_SYS_CACHELINE_SIZE 32
-
#include <asm/arch/imx-regs.h>
#define CONFIG_VF610
#define CONFIG_SYS_FSL_CLK
#define CONFIG_SYS_DCACHE_OFF
-#define CONFIG_SYS_CACHELINE_SIZE 32
#define CONFIG_DISPLAY_CPUINFO
/* Have release address at the end of 256MB for now */
#define CPU_RELEASE_ADDR 0xFFFFFF0
-/* Cache Definitions */
-#define CONFIG_SYS_CACHELINE_SIZE 64
-
#if !defined(CONFIG_IDENT_STRING)
# define CONFIG_IDENT_STRING " Xilinx ZynqMP"
#endif
#endif
/* Cache options */
-#define CONFIG_SYS_CACHELINE_SIZE 32
-
#define CONFIG_SYS_L2CACHE_OFF
#ifndef CONFIG_SYS_L2CACHE_OFF
# define CONFIG_SYS_L2_PL310
--- /dev/null
+/*
+ * Copyright (C) 2016 Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN8I_H3_H_
+#define _DT_BINDINGS_CLK_SUN8I_H3_H_
+
+#define CLK_CPUX 14
+
+#define CLK_BUS_CE 20
+#define CLK_BUS_DMA 21
+#define CLK_BUS_MMC0 22
+#define CLK_BUS_MMC1 23
+#define CLK_BUS_MMC2 24
+#define CLK_BUS_NAND 25
+#define CLK_BUS_DRAM 26
+#define CLK_BUS_EMAC 27
+#define CLK_BUS_TS 28
+#define CLK_BUS_HSTIMER 29
+#define CLK_BUS_SPI0 30
+#define CLK_BUS_SPI1 31
+#define CLK_BUS_OTG 32
+#define CLK_BUS_EHCI0 33
+#define CLK_BUS_EHCI1 34
+#define CLK_BUS_EHCI2 35
+#define CLK_BUS_EHCI3 36
+#define CLK_BUS_OHCI0 37
+#define CLK_BUS_OHCI1 38
+#define CLK_BUS_OHCI2 39
+#define CLK_BUS_OHCI3 40
+#define CLK_BUS_VE 41
+#define CLK_BUS_TCON0 42
+#define CLK_BUS_TCON1 43
+#define CLK_BUS_DEINTERLACE 44
+#define CLK_BUS_CSI 45
+#define CLK_BUS_TVE 46
+#define CLK_BUS_HDMI 47
+#define CLK_BUS_DE 48
+#define CLK_BUS_GPU 49
+#define CLK_BUS_MSGBOX 50
+#define CLK_BUS_SPINLOCK 51
+#define CLK_BUS_CODEC 52
+#define CLK_BUS_SPDIF 53
+#define CLK_BUS_PIO 54
+#define CLK_BUS_THS 55
+#define CLK_BUS_I2S0 56
+#define CLK_BUS_I2S1 57
+#define CLK_BUS_I2S2 58
+#define CLK_BUS_I2C0 59
+#define CLK_BUS_I2C1 60
+#define CLK_BUS_I2C2 61
+#define CLK_BUS_UART0 62
+#define CLK_BUS_UART1 63
+#define CLK_BUS_UART2 64
+#define CLK_BUS_UART3 65
+#define CLK_BUS_SCR 66
+#define CLK_BUS_EPHY 67
+#define CLK_BUS_DBG 68
+
+#define CLK_THS 69
+#define CLK_NAND 70
+#define CLK_MMC0 71
+#define CLK_MMC0_SAMPLE 72
+#define CLK_MMC0_OUTPUT 73
+#define CLK_MMC1 74
+#define CLK_MMC1_SAMPLE 75
+#define CLK_MMC1_OUTPUT 76
+#define CLK_MMC2 77
+#define CLK_MMC2_SAMPLE 78
+#define CLK_MMC2_OUTPUT 79
+#define CLK_TS 80
+#define CLK_CE 81
+#define CLK_SPI0 82
+#define CLK_SPI1 83
+#define CLK_I2S0 84
+#define CLK_I2S1 85
+#define CLK_I2S2 86
+#define CLK_SPDIF 87
+#define CLK_USB_PHY0 88
+#define CLK_USB_PHY1 89
+#define CLK_USB_PHY2 90
+#define CLK_USB_PHY3 91
+#define CLK_USB_OHCI0 92
+#define CLK_USB_OHCI1 93
+#define CLK_USB_OHCI2 94
+#define CLK_USB_OHCI3 95
+
+#define CLK_DRAM_VE 97
+#define CLK_DRAM_CSI 98
+#define CLK_DRAM_DEINTERLACE 99
+#define CLK_DRAM_TS 100
+#define CLK_DE 101
+#define CLK_TCON0 102
+#define CLK_TVE 103
+#define CLK_DEINTERLACE 104
+#define CLK_CSI_MISC 105
+#define CLK_CSI_SCLK 106
+#define CLK_CSI_MCLK 107
+#define CLK_VE 108
+#define CLK_AC_DIG 109
+#define CLK_AVS 110
+#define CLK_HDMI 111
+#define CLK_HDMI_DDC 112
+
+#define CLK_GPU 114
+
+#endif /* _DT_BINDINGS_CLK_SUN8I_H3_H_ */
--- /dev/null
+/*
+ * Copyright (C) 2016 Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#ifndef _DT_BINDINGS_RST_SUN8I_H3_H_
+#define _DT_BINDINGS_RST_SUN8I_H3_H_
+
+#define RST_USB_PHY0 0
+#define RST_USB_PHY1 1
+#define RST_USB_PHY2 2
+#define RST_USB_PHY3 3
+
+#define RST_MBUS 4
+
+#define RST_BUS_CE 5
+#define RST_BUS_DMA 6
+#define RST_BUS_MMC0 7
+#define RST_BUS_MMC1 8
+#define RST_BUS_MMC2 9
+#define RST_BUS_NAND 10
+#define RST_BUS_DRAM 11
+#define RST_BUS_EMAC 12
+#define RST_BUS_TS 13
+#define RST_BUS_HSTIMER 14
+#define RST_BUS_SPI0 15
+#define RST_BUS_SPI1 16
+#define RST_BUS_OTG 17
+#define RST_BUS_EHCI0 18
+#define RST_BUS_EHCI1 19
+#define RST_BUS_EHCI2 20
+#define RST_BUS_EHCI3 21
+#define RST_BUS_OHCI0 22
+#define RST_BUS_OHCI1 23
+#define RST_BUS_OHCI2 24
+#define RST_BUS_OHCI3 25
+#define RST_BUS_VE 26
+#define RST_BUS_TCON0 27
+#define RST_BUS_TCON1 28
+#define RST_BUS_DEINTERLACE 29
+#define RST_BUS_CSI 30
+#define RST_BUS_TVE 31
+#define RST_BUS_HDMI0 32
+#define RST_BUS_HDMI1 33
+#define RST_BUS_DE 34
+#define RST_BUS_GPU 35
+#define RST_BUS_MSGBOX 36
+#define RST_BUS_SPINLOCK 37
+#define RST_BUS_DBG 38
+#define RST_BUS_EPHY 39
+#define RST_BUS_CODEC 40
+#define RST_BUS_SPDIF 41
+#define RST_BUS_THS 42
+#define RST_BUS_I2S0 43
+#define RST_BUS_I2S1 44
+#define RST_BUS_I2S2 45
+#define RST_BUS_I2C0 46
+#define RST_BUS_I2C1 47
+#define RST_BUS_I2C2 48
+#define RST_BUS_UART0 49
+#define RST_BUS_UART1 50
+#define RST_BUS_UART2 51
+#define RST_BUS_UART3 52
+#define RST_BUS_SCR 53
+
+#endif /* _DT_BINDINGS_RST_SUN8I_H3_H_ */
<defconfig_name> is the name of the defconfig.
<action*> shows what the tool did for that defconfig.
-It looks like one of the followings:
+It looks like one of the following:
- Move 'CONFIG_... '
This config option was moved to the defconfig
# Here is the list of cross-tools I use.
# Most of them are available at kernel.org
-# (https://www.kernel.org/pub/tools/crosstool/files/bin/), except the followings:
+# (https://www.kernel.org/pub/tools/crosstool/files/bin/), except the following:
# arc: https://github.com/foss-for-synopsys-dwc-arc-processors/toolchain/releases
# blackfin: http://sourceforge.net/projects/adi-toolchain/files/
# nds32: http://osdk.andestech.com/packages/nds32le-linux-glibc-v1.tgz
'powerpc': 'powerpc-linux-',
'sh': 'sh-linux-gnu-',
'sparc': 'sparc-linux-',
- 'x86': 'i386-linux-'
+ 'x86': 'i386-linux-',
+ 'xtensa': 'xtensa-linux-'
}
STATE_IDLE = 0
projects / u-boot / commitdiff