mx31pdk i.MX31
mx53ard i.MX53
mx53smd i.MX53
- mx6qsabresd i.MX6Q
+ mx6sabresd i.MX6Q/DL
mx6qsabreauto i.MX6Q
wandboard i.MX6DL/S
mx6slevk i.MX6SL
+++ /dev/null
-#
-# Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
-#
-# (C) Copyright 2011 Freescale Semiconductor, Inc.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB = $(obj)lib$(BOARD).o
-
-COBJS := mx6qsabresd.o
-
-SRCS := $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-
-$(LIB): $(obj).depend $(OBJS)
- $(call cmd_link_o_target, $(OBJS))
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
+++ /dev/null
-/*
- * Copyright (C) 2012 Freescale Semiconductor, Inc.
- *
- * Author: Fabio Estevam <fabio.estevam@freescale.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/iomux.h>
-#include <asm/arch/mx6q_pins.h>
-#include <asm/errno.h>
-#include <asm/gpio.h>
-#include <asm/imx-common/iomux-v3.h>
-#include <asm/imx-common/boot_mode.h>
-#include <mmc.h>
-#include <fsl_esdhc.h>
-#include <miiphy.h>
-#include <netdev.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
- PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
- PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
- PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
-
-int dram_init(void)
-{
- gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
-
- return 0;
-}
-
-iomux_v3_cfg_t const uart1_pads[] = {
- MX6_PAD_CSI0_DAT10__UART1_TXD | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_CSI0_DAT11__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-iomux_v3_cfg_t const enet_pads[] = {
- MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TXC__ENET_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD0__ENET_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD1__ENET_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD2__ENET_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TD3__ENET_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RXC__ENET_RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD0__ENET_RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD1__ENET_RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD2__ENET_RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RD3__ENET_RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
- MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
- /* AR8031 PHY Reset */
- MX6_PAD_ENET_CRS_DV__GPIO_1_25 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static void setup_iomux_enet(void)
-{
- imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
-
- /* Reset AR8031 PHY */
- gpio_direction_output(IMX_GPIO_NR(1, 25) , 0);
- udelay(500);
- gpio_set_value(IMX_GPIO_NR(1, 25), 1);
-}
-
-iomux_v3_cfg_t const usdhc2_pads[] = {
- MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DAT0__USDHC2_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DAT1__USDHC2_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DAT2__USDHC2_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD2_DAT3__USDHC2_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NANDF_D4__USDHC2_DAT4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NANDF_D5__USDHC2_DAT5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NANDF_D6__USDHC2_DAT6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NANDF_D7__USDHC2_DAT7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NANDF_D2__GPIO_2_2 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
-};
-
-iomux_v3_cfg_t const usdhc3_pads[] = {
- MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT0__USDHC3_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT1__USDHC3_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT2__USDHC3_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT3__USDHC3_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT4__USDHC3_DAT4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT5__USDHC3_DAT5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT6__USDHC3_DAT6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD3_DAT7__USDHC3_DAT7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_NANDF_D0__GPIO_2_0 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
-};
-
-iomux_v3_cfg_t const usdhc4_pads[] = {
- MX6_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT0__USDHC4_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT1__USDHC4_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT2__USDHC4_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT3__USDHC4_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT4__USDHC4_DAT4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT5__USDHC4_DAT5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT6__USDHC4_DAT6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
- MX6_PAD_SD4_DAT7__USDHC4_DAT7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-};
-
-static void setup_iomux_uart(void)
-{
- imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
-}
-
-#ifdef CONFIG_FSL_ESDHC
-struct fsl_esdhc_cfg usdhc_cfg[3] = {
- {USDHC2_BASE_ADDR},
- {USDHC3_BASE_ADDR},
- {USDHC4_BASE_ADDR},
-};
-
-#define USDHC2_CD_GPIO IMX_GPIO_NR(2, 2)
-#define USDHC3_CD_GPIO IMX_GPIO_NR(2, 0)
-
-int board_mmc_getcd(struct mmc *mmc)
-{
- struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
- int ret = 0;
-
- switch (cfg->esdhc_base) {
- case USDHC2_BASE_ADDR:
- ret = !gpio_get_value(USDHC2_CD_GPIO);
- break;
- case USDHC3_BASE_ADDR:
- ret = !gpio_get_value(USDHC3_CD_GPIO);
- break;
- case USDHC4_BASE_ADDR:
- ret = 1; /* eMMC/uSDHC4 is always present */
- break;
- }
-
- return ret;
-}
-
-int board_mmc_init(bd_t *bis)
-{
- s32 status = 0;
- int i;
-
- /*
- * According to the board_mmc_init() the following map is done:
- * (U-boot device node) (Physical Port)
- * mmc0 SD2
- * mmc1 SD3
- * mmc2 eMMC
- */
- for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
- switch (i) {
- case 0:
- imx_iomux_v3_setup_multiple_pads(
- usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
- gpio_direction_input(USDHC2_CD_GPIO);
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
- break;
- case 1:
- imx_iomux_v3_setup_multiple_pads(
- usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
- gpio_direction_input(USDHC3_CD_GPIO);
- usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
- break;
- case 2:
- imx_iomux_v3_setup_multiple_pads(
- usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
- usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
- break;
- default:
- printf("Warning: you configured more USDHC controllers"
- "(%d) then supported by the board (%d)\n",
- i + 1, CONFIG_SYS_FSL_USDHC_NUM);
- return status;
- }
-
- status |= fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
- }
-
- return status;
-}
-#endif
-
-int mx6_rgmii_rework(struct phy_device *phydev)
-{
- unsigned short val;
-
- /* To enable AR8031 ouput a 125MHz clk from CLK_25M */
- phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
- phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
- phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
-
- val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
- val &= 0xffe3;
- val |= 0x18;
- phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
-
- /* introduce tx clock delay */
- phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
- val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
- val |= 0x0100;
- phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
-
- return 0;
-}
-
-int board_phy_config(struct phy_device *phydev)
-{
- mx6_rgmii_rework(phydev);
-
- if (phydev->drv->config)
- phydev->drv->config(phydev);
-
- return 0;
-}
-
-int board_eth_init(bd_t *bis)
-{
- int ret;
-
- setup_iomux_enet();
-
- ret = cpu_eth_init(bis);
- if (ret)
- printf("FEC MXC: %s:failed\n", __func__);
-
- return 0;
-}
-
-int board_early_init_f(void)
-{
- setup_iomux_uart();
-
- return 0;
-}
-
-int board_init(void)
-{
- /* address of boot parameters */
- gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
-
- return 0;
-}
-
-#ifdef CONFIG_CMD_BMODE
-static const struct boot_mode board_boot_modes[] = {
- /* 4 bit bus width */
- {"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
- {"sd3", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
- /* 8 bit bus width */
- {"emmc", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)},
- {NULL, 0},
-};
-#endif
-
-int board_late_init(void)
-{
-#ifdef CONFIG_CMD_BMODE
- add_board_boot_modes(board_boot_modes);
-#endif
-
- return 0;
-}
-
-int checkboard(void)
-{
- puts("Board: MX6Q-SabreSD\n");
-
- return 0;
-}
--- /dev/null
+#
+# Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
+#
+# (C) Copyright 2011 Freescale Semiconductor, Inc.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS := mx6sabresd.o
+
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(call cmd_link_o_target, $(OBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+/*
+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
+ *
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <miiphy.h>
+#include <netdev.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
+ PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
+ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
+ PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
+
+int dram_init(void)
+{
+ gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+
+ return 0;
+}
+
+iomux_v3_cfg_t const uart1_pads[] = {
+ MX6_PAD_CSI0_DAT10__UART1_TXD | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_CSI0_DAT11__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const enet_pads[] = {
+ MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TXC__ENET_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD0__ENET_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD1__ENET_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD2__ENET_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TD3__ENET_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RXC__ENET_RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD0__ENET_RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD1__ENET_RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD2__ENET_RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RD3__ENET_RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+ /* AR8031 PHY Reset */
+ MX6_PAD_ENET_CRS_DV__GPIO_1_25 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void setup_iomux_enet(void)
+{
+ imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+
+ /* Reset AR8031 PHY */
+ gpio_direction_output(IMX_GPIO_NR(1, 25) , 0);
+ udelay(500);
+ gpio_set_value(IMX_GPIO_NR(1, 25), 1);
+}
+
+iomux_v3_cfg_t const usdhc2_pads[] = {
+ MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT0__USDHC2_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT1__USDHC2_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT2__USDHC2_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD2_DAT3__USDHC2_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NANDF_D4__USDHC2_DAT4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NANDF_D5__USDHC2_DAT5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NANDF_D6__USDHC2_DAT6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NANDF_D7__USDHC2_DAT7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NANDF_D2__GPIO_2_2 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
+};
+
+iomux_v3_cfg_t const usdhc3_pads[] = {
+ MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT0__USDHC3_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT1__USDHC3_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT2__USDHC3_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT3__USDHC3_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT4__USDHC3_DAT4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT5__USDHC3_DAT5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT6__USDHC3_DAT6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD3_DAT7__USDHC3_DAT7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NANDF_D0__GPIO_2_0 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
+};
+
+iomux_v3_cfg_t const usdhc4_pads[] = {
+ MX6_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_DAT0__USDHC4_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_DAT1__USDHC4_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_DAT2__USDHC4_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_DAT3__USDHC4_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_DAT4__USDHC4_DAT4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_DAT5__USDHC4_DAT5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_DAT6__USDHC4_DAT6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_SD4_DAT7__USDHC4_DAT7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+ imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+#ifdef CONFIG_FSL_ESDHC
+struct fsl_esdhc_cfg usdhc_cfg[3] = {
+ {USDHC2_BASE_ADDR},
+ {USDHC3_BASE_ADDR},
+ {USDHC4_BASE_ADDR},
+};
+
+#define USDHC2_CD_GPIO IMX_GPIO_NR(2, 2)
+#define USDHC3_CD_GPIO IMX_GPIO_NR(2, 0)
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ int ret = 0;
+
+ switch (cfg->esdhc_base) {
+ case USDHC2_BASE_ADDR:
+ ret = !gpio_get_value(USDHC2_CD_GPIO);
+ break;
+ case USDHC3_BASE_ADDR:
+ ret = !gpio_get_value(USDHC3_CD_GPIO);
+ break;
+ case USDHC4_BASE_ADDR:
+ ret = 1; /* eMMC/uSDHC4 is always present */
+ break;
+ }
+
+ return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ s32 status = 0;
+ int i;
+
+ /*
+ * According to the board_mmc_init() the following map is done:
+ * (U-boot device node) (Physical Port)
+ * mmc0 SD2
+ * mmc1 SD3
+ * mmc2 eMMC
+ */
+ for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+ switch (i) {
+ case 0:
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+ gpio_direction_input(USDHC2_CD_GPIO);
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+ break;
+ case 1:
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+ gpio_direction_input(USDHC3_CD_GPIO);
+ usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+ break;
+ case 2:
+ imx_iomux_v3_setup_multiple_pads(
+ usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+ usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+ break;
+ default:
+ printf("Warning: you configured more USDHC controllers"
+ "(%d) then supported by the board (%d)\n",
+ i + 1, CONFIG_SYS_FSL_USDHC_NUM);
+ return status;
+ }
+
+ status |= fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+ }
+
+ return status;
+}
+#endif
+
+int mx6_rgmii_rework(struct phy_device *phydev)
+{
+ unsigned short val;
+
+ /* To enable AR8031 ouput a 125MHz clk from CLK_25M */
+ phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
+
+ val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
+ val &= 0xffe3;
+ val |= 0x18;
+ phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
+
+ /* introduce tx clock delay */
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
+ val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
+ val |= 0x0100;
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
+
+ return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+ mx6_rgmii_rework(phydev);
+
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
+ return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+ int ret;
+
+ setup_iomux_enet();
+
+ ret = cpu_eth_init(bis);
+ if (ret)
+ printf("FEC MXC: %s:failed\n", __func__);
+
+ return 0;
+}
+
+int board_early_init_f(void)
+{
+ setup_iomux_uart();
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+ return 0;
+}
+
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+ /* 4 bit bus width */
+ {"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
+ {"sd3", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
+ /* 8 bit bus width */
+ {"emmc", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)},
+ {NULL, 0},
+};
+#endif
+
+int board_late_init(void)
+{
+#ifdef CONFIG_CMD_BMODE
+ add_board_boot_modes(board_boot_modes);
+#endif
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: MX6-SabreSD\n");
+ return 0;
+}
vision2 arm armv7 vision2 ttcontrol mx5 vision2:IMX_CONFIG=board/ttcontrol/vision2/imximage_hynix.cfg
cgtqmx6qeval arm armv7 cgtqmx6eval congatec mx6 cgtqmx6eval:IMX_CONFIG=board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg,MX6Q
mx6qarm2 arm armv7 mx6qarm2 freescale mx6 mx6qarm2:IMX_CONFIG=board/freescale/mx6qarm2/imximage.cfg
-mx6qsabreauto arm armv7 mx6qsabreauto freescale mx6 mx6qsabreauto:IMX_CONFIG=board/freescale/mx6qsabreauto/imximage.cfg
+mx6qsabreauto arm armv7 mx6qsabreauto freescale mx6 mx6qsabreauto:IMX_CONFIG=board/freescale/mx6qsabreauto/imximage.cfg,MX6Q
mx6qsabrelite arm armv7 mx6qsabrelite freescale mx6 mx6qsabrelite:IMX_CONFIG=board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg
-mx6qsabresd arm armv7 mx6qsabresd freescale mx6 mx6qsabresd:IMX_CONFIG=board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg
+mx6dlsabresd arm armv7 mx6sabresd freescale mx6 mx6sabresd:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6dl.cfg,MX6DL
+mx6qsabresd arm armv7 mx6sabresd freescale mx6 mx6sabresd:IMX_CONFIG=board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg,MX6Q
mx6slevk arm armv7 mx6slevk freescale mx6 mx6slevk:IMX_CONFIG=board/freescale/mx6slevk/imximage.cfg,MX6SL
titanium arm armv7 titanium freescale mx6 titanium:IMX_CONFIG=board/freescale/titanium/imximage.cfg
vf610twr arm armv7 vf610twr freescale vf610 vf610twr:IMX_CONFIG=board/freescale/vf610twr/imximage.cfg
+++ /dev/null
-/*
- * Copyright (C) 2012 Freescale Semiconductor, Inc.
- *
- * Configuration settings for the Freescale i.MX6Q SabreSD board.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef __MX6QSABRE_COMMON_CONFIG_H
-#define __MX6QSABRE_COMMON_CONFIG_H
-
-#define CONFIG_MX6
-#define CONFIG_MX6Q
-
-#include "mx6_common.h"
-
-#define CONFIG_DISPLAY_CPUINFO
-#define CONFIG_DISPLAY_BOARDINFO
-
-#include <asm/arch/imx-regs.h>
-
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-#define CONFIG_REVISION_TAG
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024)
-
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_BOARD_LATE_INIT
-#define CONFIG_MXC_GPIO
-
-#define CONFIG_MXC_UART
-
-/* MMC Configs */
-#define CONFIG_FSL_ESDHC
-#define CONFIG_FSL_USDHC
-#define CONFIG_SYS_FSL_ESDHC_ADDR 0
-
-#define CONFIG_MMC
-#define CONFIG_CMD_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_BOUNCE_BUFFER
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
-
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_FEC_MXC
-#define CONFIG_MII
-#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE RGMII
-#define CONFIG_ETHPRIME "FEC"
-#define CONFIG_FEC_MXC_PHYADDR 1
-
-#define CONFIG_PHYLIB
-#define CONFIG_PHY_ATHEROS
-
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
-
-/* Command definition */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_BMODE
-#define CONFIG_CMD_BOOTZ
-#define CONFIG_CMD_SETEXPR
-#undef CONFIG_CMD_IMLS
-
-#define CONFIG_BOOTDELAY 1
-
-#define CONFIG_LOADADDR 0x12000000
-#define CONFIG_SYS_TEXT_BASE 0x17800000
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "script=boot.scr\0" \
- "uimage=uImage\0" \
- "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
- "fdt_addr=0x11000000\0" \
- "boot_fdt=try\0" \
- "ip_dyn=yes\0" \
- "console=" CONFIG_CONSOLE_DEV "\0" \
- "fdt_high=0xffffffff\0" \
- "initrd_high=0xffffffff\0" \
- "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
- "mmcpart=1\0" \
- "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
- "update_sd_firmware=" \
- "if test ${ip_dyn} = yes; then " \
- "setenv get_cmd dhcp; " \
- "else " \
- "setenv get_cmd tftp; " \
- "fi; " \
- "if mmc dev ${mmcdev}; then " \
- "if ${get_cmd} ${update_sd_firmware_filename}; then " \
- "setexpr fw_sz ${filesize} / 0x200; " \
- "setexpr fw_sz ${fw_sz} + 1; " \
- "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
- "fi; " \
- "fi\0" \
- "mmcargs=setenv bootargs console=${console},${baudrate} " \
- "root=${mmcroot}\0" \
- "loadbootscript=" \
- "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
- "bootscript=echo Running bootscript from mmc ...; " \
- "source\0" \
- "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
- "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
- "mmcboot=echo Booting from mmc ...; " \
- "run mmcargs; " \
- "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
- "if run loadfdt; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "if test ${boot_fdt} = try; then " \
- "bootm; " \
- "else " \
- "echo WARN: Cannot load the DT; " \
- "fi; " \
- "fi; " \
- "else " \
- "bootm; " \
- "fi;\0" \
- "netargs=setenv bootargs console=${console},${baudrate} " \
- "root=/dev/nfs " \
- "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
- "netboot=echo Booting from net ...; " \
- "run netargs; " \
- "if test ${ip_dyn} = yes; then " \
- "setenv get_cmd dhcp; " \
- "else " \
- "setenv get_cmd tftp; " \
- "fi; " \
- "${get_cmd} ${uimage}; " \
- "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
- "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "if test ${boot_fdt} = try; then " \
- "bootm; " \
- "else " \
- "echo WARN: Cannot load the DT; " \
- "fi; " \
- "fi; " \
- "else " \
- "bootm; " \
- "fi;\0"
-
-#define CONFIG_BOOTCOMMAND \
- "mmc dev ${mmcdev};" \
- "if mmc rescan; then " \
- "if run loadbootscript; then " \
- "run bootscript; " \
- "else " \
- "if run loaduimage; then " \
- "run mmcboot; " \
- "else run netboot; " \
- "fi; " \
- "fi; " \
- "else run netboot; fi"
-
-#define CONFIG_ARP_TIMEOUT 200UL
-
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#define CONFIG_SYS_PROMPT "U-Boot > "
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_CBSIZE 256
-
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
-#define CONFIG_SYS_MEMTEST_START 0x10000000
-#define CONFIG_SYS_MEMTEST_END 0x10010000
-#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
-
-#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-#define CONFIG_SYS_HZ 1000
-
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_STACKSIZE (128 * 1024)
-
-/* Physical Memory Map */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
-#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
-
-#define CONFIG_SYS_INIT_SP_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-
-/* FLASH and environment organization */
-#define CONFIG_SYS_NO_FLASH
-
-#define CONFIG_ENV_SIZE (8 * 1024)
-
-#define CONFIG_ENV_IS_IN_MMC
-
-#if defined(CONFIG_ENV_IS_IN_MMC)
-#define CONFIG_ENV_OFFSET (6 * 64 * 1024)
-#endif
-
-#define CONFIG_OF_LIBFDT
-
-#ifndef CONFIG_SYS_DCACHE_OFF
-#define CONFIG_CMD_CACHE
-#endif
-
-#endif /* __MX6QSABRE_COMMON_CONFIG_H */
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
-#include "mx6qsabre_common.h"
+#include "mx6sabre_common.h"
#define CONFIG_SYS_FSL_USDHC_NUM 2
#if defined(CONFIG_ENV_IS_IN_MMC)
+++ /dev/null
-/*
- * Copyright (C) 2012 Freescale Semiconductor, Inc.
- *
- * Configuration settings for the Freescale i.MX6Q SabreSD board.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#ifndef __MX6QSABRESD_CONFIG_H
-#define __MX6QSABRESD_CONFIG_H
-
-#define CONFIG_MACH_TYPE 3980
-#define CONFIG_MXC_UART_BASE UART1_BASE
-#define CONFIG_CONSOLE_DEV "ttymxc0"
-#define CONFIG_MMCROOT "/dev/mmcblk1p2"
-#define CONFIG_DEFAULT_FDT_FILE "imx6q-sabresd.dtb"
-#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)
-
-#include "mx6qsabre_common.h"
-
-#define CONFIG_SYS_FSL_USDHC_NUM 3
-#if defined(CONFIG_ENV_IS_IN_MMC)
-#define CONFIG_SYS_MMC_ENV_DEV 1 /* SDHC3 */
-#endif
-
-#endif /* __MX6QSABRESD_CONFIG_H */
--- /dev/null
+/*
+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for the Freescale i.MX6Q SabreSD board.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __MX6QSABRE_COMMON_CONFIG_H
+#define __MX6QSABRE_COMMON_CONFIG_H
+
+#define CONFIG_MX6
+
+#include "mx6_common.h"
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#include <asm/arch/imx-regs.h>
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
+#define CONFIG_MXC_GPIO
+
+#define CONFIG_MXC_UART
+
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR 0
+
+#define CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_BOUNCE_BUFFER
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_FEC_MXC
+#define CONFIG_MII
+#define IMX_FEC_BASE ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE RGMII
+#define CONFIG_ETHPRIME "FEC"
+#define CONFIG_FEC_MXC_PHYADDR 1
+
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ATHEROS
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_BAUDRATE 115200
+
+/* Command definition */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BMODE
+#define CONFIG_CMD_BOOTZ
+#define CONFIG_CMD_SETEXPR
+#undef CONFIG_CMD_IMLS
+
+#define CONFIG_BOOTDELAY 1
+
+#define CONFIG_LOADADDR 0x12000000
+#define CONFIG_SYS_TEXT_BASE 0x17800000
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "script=boot.scr\0" \
+ "uimage=uImage\0" \
+ "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
+ "fdt_addr=0x11000000\0" \
+ "boot_fdt=try\0" \
+ "ip_dyn=yes\0" \
+ "console=" CONFIG_CONSOLE_DEV "\0" \
+ "fdt_high=0xffffffff\0" \
+ "initrd_high=0xffffffff\0" \
+ "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
+ "mmcpart=1\0" \
+ "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
+ "update_sd_firmware=" \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "if mmc dev ${mmcdev}; then " \
+ "if ${get_cmd} ${update_sd_firmware_filename}; then " \
+ "setexpr fw_sz ${filesize} / 0x200; " \
+ "setexpr fw_sz ${fw_sz} + 1; " \
+ "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
+ "fi; " \
+ "fi\0" \
+ "mmcargs=setenv bootargs console=${console},${baudrate} " \
+ "root=${mmcroot}\0" \
+ "loadbootscript=" \
+ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source\0" \
+ "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
+ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if run loadfdt; then " \
+ "bootm ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootm; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "bootm; " \
+ "fi;\0" \
+ "netargs=setenv bootargs console=${console},${baudrate} " \
+ "root=/dev/nfs " \
+ "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+ "netboot=echo Booting from net ...; " \
+ "run netargs; " \
+ "if test ${ip_dyn} = yes; then " \
+ "setenv get_cmd dhcp; " \
+ "else " \
+ "setenv get_cmd tftp; " \
+ "fi; " \
+ "${get_cmd} ${uimage}; " \
+ "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
+ "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+ "bootm ${loadaddr} - ${fdt_addr}; " \
+ "else " \
+ "if test ${boot_fdt} = try; then " \
+ "bootm; " \
+ "else " \
+ "echo WARN: Cannot load the DT; " \
+ "fi; " \
+ "fi; " \
+ "else " \
+ "bootm; " \
+ "fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+ "mmc dev ${mmcdev};" \
+ "if mmc rescan; then " \
+ "if run loadbootscript; then " \
+ "run bootscript; " \
+ "else " \
+ "if run loaduimage; then " \
+ "run mmcboot; " \
+ "else run netboot; " \
+ "fi; " \
+ "fi; " \
+ "else run netboot; fi"
+
+#define CONFIG_ARP_TIMEOUT 200UL
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_PROMPT "U-Boot > "
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_SYS_CBSIZE 256
+
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS 16
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_MEMTEST_START 0x10000000
+#define CONFIG_SYS_MEMTEST_END 0x10010000
+#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
+
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+#define CONFIG_SYS_HZ 1000
+
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_STACKSIZE (128 * 1024)
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS 1
+#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* FLASH and environment organization */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_ENV_SIZE (8 * 1024)
+
+#define CONFIG_ENV_IS_IN_MMC
+
+#if defined(CONFIG_ENV_IS_IN_MMC)
+#define CONFIG_ENV_OFFSET (6 * 64 * 1024)
+#endif
+
+#define CONFIG_OF_LIBFDT
+
+#ifndef CONFIG_SYS_DCACHE_OFF
+#define CONFIG_CMD_CACHE
+#endif
+
+#endif /* __MX6QSABRE_COMMON_CONFIG_H */
--- /dev/null
+/*
+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for the Freescale i.MX6Q SabreSD board.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __MX6QSABRESD_CONFIG_H
+#define __MX6QSABRESD_CONFIG_H
+
+#define CONFIG_MACH_TYPE 3980
+#define CONFIG_MXC_UART_BASE UART1_BASE
+#define CONFIG_CONSOLE_DEV "ttymxc0"
+#define CONFIG_MMCROOT "/dev/mmcblk1p2"
+#define CONFIG_DEFAULT_FDT_FILE "imx6q-sabresd.dtb"
+#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)
+
+#include "mx6sabre_common.h"
+
+#define CONFIG_SYS_FSL_USDHC_NUM 3
+#if defined(CONFIG_ENV_IS_IN_MMC)
+#define CONFIG_SYS_MMC_ENV_DEV 1 /* SDHC3 */
+#endif
+
+#endif /* __MX6QSABRESD_CONFIG_H */
projects / u-boot / commitdiff