If defined, the x86 reset vector code is included. This is not
needed when U-Boot is running from Coreboot.
-- CONFIG_SYS_MPUCLK
- Defines the MPU clock speed (in MHz).
-
- NOTE : currently only supported on AM335x platforms.
-
- CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC:
Enables the RTC32K OSC on AM33xx based plattforms
#define MPUPLL_M_550 550
#define MPUPLL_M_300 300
-/* MAIN PLL Fdll = 550 MHz, by default */
-#ifndef CONFIG_SYS_MPUCLK
-#define CONFIG_SYS_MPUCLK MPUPLL_M_550
-#endif
-
#define UART_RESET (0x1 << 1)
#define UART_CLK_RUNNING_MASK 0x1
#define UART_SMART_IDLE_EN (0x1 << 0x3)
endchoice
+config SYS_MPUCLK
+ int "MPU CLK speed"
+ default 550
+ help
+ Defines the MPU clock speed (in MHz).
config TI_SECURE_DEVICE
bool "HS Device Type Support"
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_DRACO=y
+CONFIG_SYS_MPUCLK=300
CONFIG_SPL_MMC_SUPPORT=y
CONFIG_SPL_SERIAL_SUPPORT=y
CONFIG_SPL_LIBDISK_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_ETAMIN=y
+CONFIG_SYS_MPUCLK=300
CONFIG_SPL_MMC_SUPPORT=y
CONFIG_SPL_SERIAL_SUPPORT=y
CONFIG_SPL_LIBDISK_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_PXM2=y
+CONFIG_SYS_MPUCLK=720
CONFIG_SPL_MMC_SUPPORT=y
CONFIG_SPL_SERIAL_SUPPORT=y
CONFIG_SPL_LIBDISK_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_RASTABAN=y
+CONFIG_SYS_MPUCLK=300
CONFIG_SPL_MMC_SUPPORT=y
CONFIG_SPL_SERIAL_SUPPORT=y
CONFIG_SPL_LIBDISK_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_RUT=y
+CONFIG_SYS_MPUCLK=600
CONFIG_SPL_MMC_SUPPORT=y
CONFIG_SPL_SERIAL_SUPPORT=y
CONFIG_SPL_LIBDISK_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_THUBAN=y
+CONFIG_SYS_MPUCLK=300
CONFIG_SPL_MMC_SUPPORT=y
CONFIG_SPL_SERIAL_SUPPORT=y
CONFIG_SPL_LIBDISK_SUPPORT=y
#include "siemens-am33x-common.h"
-#define CONFIG_SYS_MPUCLK 300
#define DDR_PLL_FREQ 303
#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
CONFIG_SYS_NAND_BASE2}
#define CONFIG_SYS_NAND_ONFI_DETECTION
-#define CONFIG_SYS_MPUCLK 300
#define DDR_PLL_FREQ 303
#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
#include "siemens-am33x-common.h"
-#define CONFIG_SYS_MPUCLK 720
#define DDR_IOCTRL_VAL 0x18b
#define DDR_PLL_FREQ 266
#include "siemens-am33x-common.h"
-#define CONFIG_SYS_MPUCLK 300
#define DDR_PLL_FREQ 303
#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
#include "siemens-am33x-common.h"
-#define CONFIG_SYS_MPUCLK 600
#define RUT_IOCTRL_VAL 0x18b
#define DDR_PLL_FREQ 303
#include "siemens-am33x-common.h"
-#define CONFIG_SYS_MPUCLK 300
#define DDR_PLL_FREQ 303
#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
CONFIG_SYS_MPTPR_2BK_2K
CONFIG_SYS_MPTPR_2BK_4K
CONFIG_SYS_MPTPR_2BK_8K
-CONFIG_SYS_MPUCLK
CONFIG_SYS_MRAM_BASE
CONFIG_SYS_MRAM_SIZE
CONFIG_SYS_MRS_OFFS