arm/km: redefine piggy 4 reg names to avoid conflicts

Some very similar #defines for reg addresses are used in a later patch
(managed_switch support for km_arm).

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>

diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c
index c8da823cb289cab715508b221408f05792535d02..ed2454ff0c0908b9cdd1815d14c2c0c9c8202523 100644 (file)
--- a/board/keymile/km_arm/km_arm.c
+++ b/board/keymile/km_arm/km_arm.c
@@ -328,13 +328,13 @@ void dram_init_banksize(void)
 
 #if (defined(CONFIG_KM_PIGGY4_88E6061))
 
-#define        PHY_LED_SEL     0x18
-#define PHY_LED0_LINK  (0x5)
-#define PHY_LED1_ACT   (0x8<<4)
-#define PHY_LED2_INT   (0xe<<8)
-#define        PHY_SPEC_CTRL   0x1c
+#define        PHY_LED_SEL_REG         0x18
+#define PHY_LED0_LINK          (0x5)
+#define PHY_LED1_ACT           (0x8<<4)
+#define PHY_LED2_INT           (0xe<<8)
+#define        PHY_SPEC_CTRL_REG       0x1c
 #define PHY_RGMII_CLK_STABLE   (0x1<<10)
-#define PHY_CLSA       (0x1<<1)
+#define PHY_CLSA               (0x1<<1)
 
 /* Configure and enable MV88E3018 PHY */
 void reset_phy(void)
@@ -346,15 +346,15 @@ void reset_phy(void)
                return;
 
        /* RGMII clk transition on data stable */
-       if (miiphy_read(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL, &reg) != 0)
+       if (!miiphy_read(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG, &reg))
                printf("Error reading PHY spec ctrl reg\n");
-       if (miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL,
-               reg | PHY_RGMII_CLK_STABLE | PHY_CLSA) != 0)
+       if (!miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_SPEC_CTRL_REG,
+               reg | PHY_RGMII_CLK_STABLE | PHY_CLSA))
                printf("Error writing PHY spec ctrl reg\n");
 
        /* leds setup */
-       if (miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_LED_SEL,
-               PHY_LED0_LINK | PHY_LED1_ACT | PHY_LED2_INT) != 0)
+       if (!miiphy_write(name, CONFIG_PHY_BASE_ADR, PHY_LED_SEL_REG,
+               PHY_LED0_LINK | PHY_LED1_ACT | PHY_LED2_INT))
                printf("Error writing PHY LED reg\n");
 
        /* reset the phy */