This patch adds NAND booting support for the AMCC Acadia eval board.
Please make sure to configure jumper J7 to position 2-3 when booting
from NOR, and to position 1-2 when booting for NAND.
I also added a board command to configure the I2C bootstrap EEPROM
values. Right now only 267MHz is support for booting either via NOR
or NAND FLASH. Here the usage:
=> bootstrap 267 nor ;to configure the board for 267MHz NOR booting
=> bootstrap 267 nand ;to configure the board for 267MHz NNAND booting
Signed-off-by: Stefan Roese <sr@denx.de>
#########################################################################
LIST_4xx=" \
- acadia ADCIOP alpr AP1000 \
- AR405 ASH405 bamboo bamboo_nand \
- bubinga CANBT CMS700 CPCI2DP \
- CPCI405 CPCI4052 CPCI405AB CPCI405DT \
- CPCI440 CPCIISER4 CRAYL1 csb272 \
- csb472 DASA_SIM DP405 DU405 \
- ebony ERIC EXBITGEN G2000 \
- HH405 HUB405 JSE KAREF \
- katmai luan METROBOX MIP405 \
- MIP405T ML2 ml300 ocotea \
- OCRTC ORSG p3p440 PCI405 \
- pcs440ep PIP405 PLU405 PMC405 \
- PPChameleonEVB sbc405 sc3 sequoia \
- sequoia_nand taishan VOH405 VOM405 \
- W7OLMC W7OLMG walnut WUH405 \
- XPEDITE1K yellowstone yosemite yucca \
+ acadia acadia_nand ADCIOP alpr \
+ AP1000 AR405 ASH405 bamboo \
+ bamboo_nand bubinga CANBT CMS700 \
+ CPCI2DP CPCI405 CPCI4052 CPCI405AB \
+ CPCI405DT CPCI440 CPCIISER4 CRAYL1 \
+ csb272 csb472 DASA_SIM DP405 \
+ DU405 ebony ERIC EXBITGEN \
+ G2000 HH405 HUB405 JSE \
+ KAREF katmai luan METROBOX \
+ MIP405 MIP405T ML2 ml300 \
+ ocotea OCRTC ORSG p3p440 \
+ PCI405 pcs440ep PIP405 PLU405 \
+ PMC405 PPChameleonEVB sbc405 sc3 \
+ sequoia sequoia_nand taishan VOH405 \
+ VOM405 W7OLMC W7OLMG walnut \
+ WUH405 XPEDITE1K yellowstone yosemite \
+ yucca \
"
#########################################################################
acadia_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc ppc4xx acadia amcc
+acadia_nand_config: unconfig
+ @mkdir -p $(obj)include
+ @mkdir -p $(obj)nand_spl
+ @mkdir -p $(obj)board/amcc/acadia
+ @echo "#define CONFIG_NAND_U_BOOT" > $(obj)include/config.h
+ @$(MKCONFIG) -n $@ -a acadia ppc ppc4xx acadia amcc
+ @echo "TEXT_BASE = 0x01000000" > $(obj)board/amcc/acadia/config.tmp
+ @echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
+
ADCIOP_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc ppc4xx adciop esd
LIB = $(obj)lib$(BOARD).a
-COBJS = $(BOARD).o cpr.o memory.o
+COBJS = $(BOARD).o cmd_acadia.o cpr.o memory.o
SOBJS =
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
acadia_gpio_init();
/* Configure 405EZ for NAND usage */
- mtsdr(sdrnand0, 0x80c00000);
- mtsdr(sdrultra0, 0x8d110000);
+ mtsdr(sdrnand0, SDR_NAND0_NDEN | SDR_NAND0_NDAREN | SDR_NAND0_NDRBEN);
+ mfsdr(sdrultra0, reg);
+ reg &= ~SDR_ULTRA0_CSN_MASK;
+ reg |= (SDR_ULTRA0_CSNSEL0 >> CFG_NAND_CS) |
+ SDR_ULTRA0_NDGPIOBP |
+ SDR_ULTRA0_EBCRDYEN |
+ SDR_ULTRA0_NFSRSTEN;
+ mtsdr(sdrultra0, reg);
/* USB Host core needs this bit set */
mfsdr(sdrultra1, reg);
--- /dev/null
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+
+static u8 boot_267_nor[] = {
+ 0xc0, 0x00, 0x00, 0x00, 0x00, 0x00, 0x8e, 0x00,
+ 0x14, 0xc0, 0x36, 0xcc, 0x00, 0x0c, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00
+};
+
+static u8 boot_267_nand[] = {
+ 0xd0, 0x38, 0xc3, 0x50, 0x13, 0x88, 0x8e, 0x00,
+ 0x14, 0xc0, 0x36, 0xcc, 0x00, 0x0c, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00
+};
+
+static int do_bootstrap(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+ u8 chip;
+ u8 *buf;
+ int cpu_freq;
+
+ if (argc < 3) {
+ printf("Usage:\n%s\n", cmdtp->usage);
+ return 1;
+ }
+
+ cpu_freq = simple_strtol(argv[1], NULL, 10);
+ if (cpu_freq != 267) {
+ printf("Unsupported cpu-frequency - only 267 supported\n");
+ return 1;
+ }
+
+ /* use 0x50 as I2C EEPROM address for now */
+ chip = 0x50;
+
+ if ((strcmp(argv[2], "nor") != 0) &&
+ (strcmp(argv[2], "nand") != 0)) {
+ printf("Unsupported boot-device - only nor|nand support\n");
+ return 1;
+ }
+
+ if (strcmp(argv[2], "nand") == 0) {
+ switch (cpu_freq) {
+ case 267:
+ buf = boot_267_nand;
+ break;
+ default:
+ break;
+ }
+ } else {
+ switch (cpu_freq) {
+ case 267:
+ buf = boot_267_nor;
+ break;
+ default:
+ break;
+ }
+ }
+
+ if (i2c_write(chip, 0, 1, buf, 16) != 0)
+ printf("Error writing to EEPROM at address 0x%x\n", chip);
+ udelay(CFG_EEPROM_PAGE_WRITE_DELAY_MS * 1000);
+ if (i2c_write(chip, 0x10, 1, buf+16, 4) != 0)
+ printf("Error2 writing to EEPROM at address 0x%x\n", chip);
+
+ printf("Done\n");
+ printf("Please power-cycle the board for the changes to take effect\n");
+
+ return 0;
+}
+
+U_BOOT_CMD(
+ bootstrap, 3, 0, do_bootstrap,
+ "bootstrap - program the I2C bootstrap EEPROM\n",
+ "<cpu-freq> <nor|nand> - program the I2C bootstrap EEPROM\n"
+ );
# MA 02111-1307 USA
#
+#
+# AMCC 405EZ Reference Platform (Acadia) board
+#
+
+sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp
+
ifndef TEXT_BASE
TEXT_BASE = 0xFFFC0000
endif
return;
}
+#if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
static void cram_bcr_write(u32 wr_val)
{
wr_val <<= 2;
return;
}
+#endif
long int initdram(int board_type)
{
+#if !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
+ int i;
u32 val;
/* 1. EBC need to program READY, CLK, ADV for ASync mode */
/* Config EBC to use RDY */
mfsdr(sdrultra0, val);
- mtsdr(sdrultra0, val | 0x04000000);
+ mtsdr(sdrultra0, val | SDR_ULTRA0_EBCRDYEN);
+
+ /* Wait a short while, since for NAND booting this is too fast */
+ for (i=0; i<200000; i++)
+ ;
+#endif
return (CFG_MBYTES_RAM << 20);
}
--- /dev/null
+/*
+ * (C) Copyright 2007
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+SECTIONS
+{
+ /* Read-only sections, merged into text segment: */
+ . = + SIZEOF_HEADERS;
+ .interp : { *(.interp) }
+ .hash : { *(.hash) }
+ .dynsym : { *(.dynsym) }
+ .dynstr : { *(.dynstr) }
+ .rel.text : { *(.rel.text) }
+ .rela.text : { *(.rela.text) }
+ .rel.data : { *(.rel.data) }
+ .rela.data : { *(.rela.data) }
+ .rel.rodata : { *(.rel.rodata) }
+ .rela.rodata : { *(.rela.rodata) }
+ .rel.got : { *(.rel.got) }
+ .rela.got : { *(.rela.got) }
+ .rel.ctors : { *(.rel.ctors) }
+ .rela.ctors : { *(.rela.ctors) }
+ .rel.dtors : { *(.rel.dtors) }
+ .rela.dtors : { *(.rela.dtors) }
+ .rel.bss : { *(.rel.bss) }
+ .rela.bss : { *(.rela.bss) }
+ .rel.plt : { *(.rel.plt) }
+ .rela.plt : { *(.rela.plt) }
+ .init : { *(.init) }
+ .plt : { *(.plt) }
+ .text :
+ {
+ /* WARNING - the following is hand-optimized to fit within */
+ /* the sector layout of our flash chips! XXX FIXME XXX */
+
+ cpu/ppc4xx/start.o (.text)
+
+ /* Align to next NAND block */
+ . = ALIGN(0x4000);
+ common/environment.o (.ppcenv)
+ /* Keep some space here for redundant env and potential bad env blocks */
+ . = ALIGN(0x10000);
+
+ *(.text)
+ *(.fixup)
+ *(.got1)
+ }
+ _etext = .;
+ PROVIDE (etext = .);
+ .rodata :
+ {
+ *(.rodata)
+ *(.rodata1)
+ *(.rodata.str1.4)
+ }
+ .fini : { *(.fini) } =0
+ .ctors : { *(.ctors) }
+ .dtors : { *(.dtors) }
+
+ /* Read-write section, merged into data segment: */
+ . = (. + 0x00FF) & 0xFFFFFF00;
+ _erotext = .;
+ PROVIDE (erotext = .);
+ .reloc :
+ {
+ *(.got)
+ _GOT2_TABLE_ = .;
+ *(.got2)
+ _FIXUP_TABLE_ = .;
+ *(.fixup)
+ }
+ __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+ __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+ .data :
+ {
+ *(.data)
+ *(.data1)
+ *(.sdata)
+ *(.sdata2)
+ *(.dynamic)
+ CONSTRUCTORS
+ }
+ _edata = .;
+ PROVIDE (edata = .);
+
+ . = .;
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+
+ . = .;
+ __start___ex_table = .;
+ __ex_table : { *(__ex_table) }
+ __stop___ex_table = .;
+
+ . = ALIGN(256);
+ __init_begin = .;
+ .text.init : { *(.text.init) }
+ .data.init : { *(.data.init) }
+ . = ALIGN(256);
+ __init_end = .;
+
+ __bss_start = .;
+ .bss :
+ {
+ *(.sbss) *(.scommon)
+ *(.dynbss)
+ *(.bss)
+ *(COMMON)
+ }
+
+ _end = . ;
+ PROVIDE (end = .);
+}
* NAND U-Boot image is started from offset 0
*/
.text
+#if defined(CONFIG_440)
bl reconfig_tlb0
+#endif
GET_GOT
bl cpu_init_f /* run low-level CPU init code (from Flash) */
bl board_init_f
#endif /* CONFIG_405EZ */
#endif
+#ifdef CONFIG_NAND_SPL
+ /*
+ * Copy SPL from cache into internal SRAM
+ */
+ li r4,(CFG_NAND_BOOT_SPL_SIZE >> 2) - 1
+ mtctr r4
+ lis r2,CFG_NAND_BOOT_SPL_SRC@h
+ ori r2,r2,CFG_NAND_BOOT_SPL_SRC@l
+ lis r3,CFG_NAND_BOOT_SPL_DST@h
+ ori r3,r3,CFG_NAND_BOOT_SPL_DST@l
+spl_loop:
+ lwzu r4,4(r2)
+ stwu r4,4(r3)
+ bdnz spl_loop
+
+ /*
+ * Jump to code in RAM
+ */
+ bl 00f
+00: mflr r10
+ lis r3,(CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)@h
+ ori r3,r3,(CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)@l
+ sub r10,r10,r3
+ addi r10,r10,28
+ mtlr r10
+ blr
+
+start_ram:
+ sync
+ isync
+#endif /* CONFIG_NAND_SPL */
+
/*----------------------------------------------------------------------- */
/* Setup temporary stack in DCACHE or OCM if needed for SDRAM SPD. */
/*----------------------------------------------------------------------- */
stw r0, +12(r1) /* Save return addr (underflow vect) */
#endif /* !(CFG_INIT_DCACHE_CS || !CFG_TEM_STACK_OCM) */
+#ifdef CONFIG_NAND_SPL
+ bl nand_boot /* will not return */
+#else
GET_GOT /* initialize GOT access */
bl cpu_init_f /* run low-level CPU init code (from Flash) */
/* NEVER RETURNS! */
bl board_init_f /* run first part of init code (from Flash) */
+#endif /* CONFIG_NAND_SPL */
#endif /* CONFIG_405GP || CONFIG_405CR || CONFIG_405 || CONFIG_405EP */
/*----------------------------------------------------------------------- */
/* Cache functions.
*/
-invalidate_icache:
- iccci r0,r0 /* for 405, iccci invalidates the */
- blr /* entire I cache */
-
-invalidate_dcache:
- addi r6,0,0x0000 /* clear GPR 6 */
- /* Do loop for # of dcache congruence classes. */
- lis r7, (CFG_DCACHE_SIZE / CFG_CACHELINE_SIZE / 2)@ha /* TBS for large sized cache */
- ori r7, r7, (CFG_DCACHE_SIZE / CFG_CACHELINE_SIZE / 2)@l
- /* NOTE: dccci invalidates both */
- mtctr r7 /* ways in the D cache */
-..dcloop:
- dccci 0,r6 /* invalidate line */
- addi r6,r6, CFG_CACHELINE_SIZE /* bump to next line */
- bdnz ..dcloop
- blr
-
flush_dcache:
addis r9,r0,0x0002 /* set mask for EE and CE msr bits */
ori r9,r9,0x8000
lwz 3,0x0000(3)
blr
+invalidate_icache:
+ iccci r0,r0 /* for 405, iccci invalidates the */
+ blr /* entire I cache */
+
+invalidate_dcache:
+ addi r6,0,0x0000 /* clear GPR 6 */
+ /* Do loop for # of dcache congruence classes. */
+ lis r7, (CFG_DCACHE_SIZE / CFG_CACHELINE_SIZE / 2)@ha /* TBS for large sized cache */
+ ori r7, r7, (CFG_DCACHE_SIZE / CFG_CACHELINE_SIZE / 2)@l
+ /* NOTE: dccci invalidates both */
+ mtctr r7 /* ways in the D cache */
+..dcloop:
+ dccci 0,r6 /* invalidate line */
+ addi r6,r6, CFG_CACHELINE_SIZE /* bump to next line */
+ bdnz ..dcloop
+ blr
+
/**************************************************************************/
/* PPC405EP specific stuff */
/**************************************************************************/
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
#define CFG_FLASH_CFI /* The flash is CFI compatible */
#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define _CFG_CMD_INCLUDE (CFG_CMD_ALL)
+#else
+#define CFG_NO_FLASH 1 /* No NOR on Acadia when NAND-booting */
+#define _CFG_CMD_INCLUDE ((CFG_CMD_ALL) & ~(CFG_CMD_FLASH | CFG_CMD_IMLS))
+#endif
+
#ifdef CFG_ENV_IS_IN_FLASH
#define CFG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */
#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
#endif
+/*
+ * IPL (Initial Program Loader, integrated inside CPU)
+ * Will load first 4k from NAND (SPL) into cache and execute it from there.
+ *
+ * SPL (Secondary Program Loader)
+ * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
+ * has to fit into 4kByte. It sets up the CPU and configures the SDRAM
+ * controller and the NAND controller so that the special U-Boot image can be
+ * loaded from NAND to SDRAM.
+ *
+ * NUB (NAND U-Boot)
+ * This NAND U-Boot (NUB) is a special U-Boot version which can be started
+ * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
+ *
+ * On 440EPx the SPL is copied to SDRAM before the NAND controller is
+ * set up. While still running from cache, I experienced problems accessing
+ * the NAND controller. sr - 2006-08-25
+ */
+#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */
+#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */
+#define CFG_NAND_BOOT_SPL_DST (CFG_OCM_DATA_ADDR + (12 << 10)) /* Copy SPL here*/
+#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */
+#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */
+#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)
+
+/*
+ * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
+ */
+#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */
+#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */
+
+/*
+ * Now the NAND chip has to be defined (no autodetection used!)
+ */
+#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */
+#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */
+#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */
+#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */
+#undef CFG_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */
+
+#define CFG_NAND_ECCSIZE 256
+#define CFG_NAND_ECCBYTES 3
+#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE)
+#define CFG_NAND_OOBSIZE 16
+#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS)
+#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
+
+#ifdef CFG_ENV_IS_IN_NAND
+/*
+ * For NAND booting the environment is embedded in the U-Boot image. Please take
+ * look at the file board/amcc/sequoia/u-boot-nand.lds for details.
+ */
+#define CFG_ENV_SIZE CFG_NAND_BLOCK_SIZE
+#define CFG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE)
+#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET + CFG_ENV_SIZE)
+#endif
+
/*-----------------------------------------------------------------------
* RAM (CRAM)
*----------------------------------------------------------------------*/
"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
"cp.b ${fileaddr} fffc0000 ${filesize};" \
"setenv filesize;saveenv\0" \
- "upd=run load;run update\0" \
+ "upd=run load update\0" \
+ "nload=tftp 200000 acadia/u-boot-nand.bin\0" \
+ "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \
+ "setenv filesize;saveenv\0" \
+ "nupd=run nload nupdate\0" \
"kozio=bootm ffc60000\0" \
""
#define CONFIG_BOOTCOMMAND "run flash_self"
#define CONFIG_SUPPORT_VFAT
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_ASKENV | \
- CFG_CMD_DHCP | \
- CFG_CMD_DTT | \
- CFG_CMD_DIAG | \
- CFG_CMD_EEPROM | \
- CFG_CMD_ELF | \
- CFG_CMD_FAT | \
- CFG_CMD_I2C | \
- CFG_CMD_IRQ | \
- CFG_CMD_MII | \
- CFG_CMD_NAND | \
- CFG_CMD_NET | \
- CFG_CMD_NFS | \
- CFG_CMD_PCI | \
- CFG_CMD_PING | \
- CFG_CMD_REGINFO | \
- CFG_CMD_USB)
+#define CONFIG_COMMANDS ((CONFIG_CMD_DFL & _CFG_CMD_INCLUDE) | \
+ CFG_CMD_ASKENV | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_DTT | \
+ CFG_CMD_DIAG | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_ELF | \
+ CFG_CMD_FAT | \
+ CFG_CMD_I2C | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_MII | \
+ CFG_CMD_NAND | \
+ CFG_CMD_NET | \
+ CFG_CMD_NFS | \
+ CFG_CMD_PCI | \
+ CFG_CMD_PING | \
+ CFG_CMD_REGINFO | \
+ CFG_CMD_USB)
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
-#define CFG_NAND_CS 3 /* NAND chip connected to CSx */
-
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#define CFG_NAND_CS 3
/* Memory Bank 0 (Flash) initialization */
#define CFG_EBC_PB0AP 0x03337200
#define CFG_EBC_PB0CR 0xfe0bc000
+/* Memory Bank 3 (NAND-FLASH) initialization */
+#define CFG_EBC_PB3AP 0x018003c0
+#define CFG_EBC_PB3CR (CFG_NAND_ADDR | 0x1c000)
+
/* Just initial configuration for CRAM. Will be changed in memory.c to sync mode*/
/* Memory Bank 1 (CRAM) initialization */
#define CFG_EBC_PB1AP 0x030400c0
/* Memory Bank 2 (CRAM) initialization */
#define CFG_EBC_PB2AP 0x030400c0
#define CFG_EBC_PB2CR 0x020bc000
+#else
+#define CFG_NAND_CS 0 /* NAND chip connected to CSx */
+/* Memory Bank 0 (NAND-FLASH) initialization */
+#define CFG_EBC_PB0AP 0x018003c0
+#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1c000)
-/* Memory Bank 3 (NAND-FLASH) initialization */
-#define CFG_EBC_PB3AP 0x018003c0
-#define CFG_EBC_PB3CR (CFG_NAND_ADDR | 0x1c000)
+/*
+ * When NAND-booting the CRAM EBC setup must be done in sync mode, since the
+ * NAND-SPL already initialized the CRAM and EBC to sync mode.
+ */
+/* Memory Bank 1 (CRAM) initialization */
+#define CFG_EBC_PB1AP 0x9C0201C0
+#define CFG_EBC_PB1CR 0x000bc000
+
+/* Memory Bank 2 (CRAM) initialization */
+#define CFG_EBC_PB2AP 0x9C0201C0
+#define CFG_EBC_PB2CR 0x020bc000
+#endif
/* Memory Bank 4 (CPLD) initialization */
#define CFG_EBC_PB4AP 0x04006000
* GPIO Setup
*----------------------------------------------------------------------*/
#define CFG_GPIO_CRAM_CLK 8
-#define CFG_GPIO_CRAM_WAIT 9
+#define CFG_GPIO_CRAM_WAIT 9 /* GPIO-In */
#define CFG_GPIO_CRAM_ADV 10
-#define CFG_GPIO_CRAM_CRE (32 + 21)
+#define CFG_GPIO_CRAM_CRE (32 + 21) /* GPIO-Out */
/*-----------------------------------------------------------------------
* Definitions for GPIO_0 setup (PPC405EZ specific)
* GPIO0[28-30] - Trace Outputs / PWM Inputs
* GPIO0[31] - PWM_8 I/O
*/
-#define CFG_GPIO0_TCR 0xC0000000
-#define CFG_GPIO0_OSRL 0x50000000
+#define CFG_GPIO0_TCR 0xC0A00000
+#define CFG_GPIO0_OSRL 0x50004400
#define CFG_GPIO0_OSRH 0x02000055
-#define CFG_GPIO0_ISR1L 0x00000000
+#define CFG_GPIO0_ISR1L 0x00001000
#define CFG_GPIO0_ISR1H 0x00000055
#define CFG_GPIO0_TSRL 0x02000000
#define CFG_GPIO0_TSRH 0x00000055
* GPIO1[16] - SPI_SS_1_N Output
* GPIO1[17-20] - Trace Output/External Interrupts IRQ0 - IRQ3 inputs
*/
-#define CFG_GPIO1_OSRH 0x55455555
+#define CFG_GPIO1_TCR 0xFFFF8414
#define CFG_GPIO1_OSRL 0x40000110
-#define CFG_GPIO1_ISR1H 0x00000000
+#define CFG_GPIO1_OSRH 0x55455555
#define CFG_GPIO1_ISR1L 0x15555445
-#define CFG_GPIO1_TSRH 0x00000000
+#define CFG_GPIO1_ISR1H 0x00000000
#define CFG_GPIO1_TSRL 0x00000000
-#define CFG_GPIO1_TCR 0xFFFF8014
+#define CFG_GPIO1_TSRH 0x00000000
/*
* Internal Definitions
#define sdricintstat 0x4510
#define SDR_NAND0_NDEN 0x80000000
+#define SDR_NAND0_NDBTEN 0x40000000
+#define SDR_NAND0_NDBADR_MASK 0x30000000
+#define SDR_NAND0_NDBPG_MASK 0x0f000000
+#define SDR_NAND0_NDAREN 0x00800000
+#define SDR_NAND0_NDRBEN 0x00400000
#define SDR_ULTRA0_NDGPIOBP 0x80000000
#define SDR_ULTRA0_CSN_MASK 0x78000000
#define SDR_ULTRA0_CSNSEL1 0x20000000
#define SDR_ULTRA0_CSNSEL2 0x10000000
#define SDR_ULTRA0_CSNSEL3 0x08000000
+#define SDR_ULTRA0_EBCRDYEN 0x04000000
+#define SDR_ULTRA0_SPISSINEN 0x02000000
+#define SDR_ULTRA0_NFSRSTEN 0x01000000
#define SDR_ULTRA1_LEDNENABLE 0x40000000
--- /dev/null
+#
+# (C) Copyright 2007
+# Stefan Roese, DENX Software Engineering, sr@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+include $(TOPDIR)/nand_spl/board/$(BOARDDIR)/config.mk
+
+LDSCRIPT= $(TOPDIR)/nand_spl/board/$(BOARDDIR)/u-boot.lds
+LDFLAGS = -Bstatic -T $(LDSCRIPT) -Ttext $(TEXT_BASE) $(PLATFORM_LDFLAGS)
+AFLAGS += -DCONFIG_NAND_SPL
+CFLAGS += -DCONFIG_NAND_SPL
+
+SOBJS = start.o resetvec.o
+COBJS = gpio.o nand_boot.o nand_ecc.o memory.o ndfc.o
+
+SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c))
+OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
+__OBJS := $(SOBJS) $(COBJS)
+LNDIR := $(OBJTREE)/nand_spl/board/$(BOARDDIR)
+
+nandobj := $(OBJTREE)/nand_spl/
+
+ALL = $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin
+
+all: $(obj).depend $(ALL)
+
+$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl
+ $(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@
+
+$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl
+ $(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
+
+$(nandobj)u-boot-spl: $(OBJS)
+ cd $(LNDIR) && $(LD) $(LDFLAGS) $$UNDEF_SYM $(__OBJS) \
+ -Map $(nandobj)u-boot-spl.map \
+ -o $(nandobj)u-boot-spl
+
+# create symbolic links for common files
+
+# from cpu directory
+$(obj)gpio.c:
+ @rm -f $(obj)gpio.c
+ ln -s $(SRCTREE)/cpu/ppc4xx/gpio.c $(obj)gpio.c
+
+$(obj)ndfc.c:
+ @rm -f $(obj)ndfc.c
+ ln -s $(SRCTREE)/cpu/ppc4xx/ndfc.c $(obj)ndfc.c
+
+$(obj)resetvec.S:
+ @rm -f $(obj)resetvec.S
+ ln -s $(SRCTREE)/cpu/ppc4xx/resetvec.S $(obj)resetvec.S
+
+$(obj)start.S:
+ @rm -f $(obj)start.S
+ ln -s $(SRCTREE)/cpu/ppc4xx/start.S $(obj)start.S
+
+# from board directory
+$(obj)memory.c:
+ @rm -f $(obj)memory.c
+ ln -s $(SRCTREE)/board/amcc/acadia/memory.c $(obj)memory.c
+
+# from nand_spl directory
+$(obj)nand_boot.c:
+ @rm -f $(obj)nand_boot.c
+ ln -s $(SRCTREE)/nand_spl/nand_boot.c $(obj)nand_boot.c
+
+# from drivers/nand directory
+$(obj)nand_ecc.c:
+ @rm -f $(obj)nand_ecc.c
+ ln -s $(SRCTREE)/drivers/nand/nand_ecc.c $(obj)nand_ecc.c
+
+#########################################################################
+
+$(obj)%.o: $(obj)%.S
+ $(CC) $(AFLAGS) -c -o $@ $<
+
+$(obj)%.o: $(obj)%.c
+ $(CC) $(CFLAGS) -c -o $@ $<
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
--- /dev/null
+#
+# (C) Copyright 2007
+# Stefan Roese, DENX Software Engineering, sr@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+#
+# AMCC 405EZ Reference Platform (Acadia) board
+#
+
+#
+# TEXT_BASE for SPL:
+#
+# On 4xx platforms the SPL is located at 0xfffff000...0xffffffff,
+# in the last 4kBytes of memory space in cache.
+# We will copy this SPL into internal SRAM in start.S. So we set
+# TEXT_BASE to starting address in internal SRAM here.
+#
+TEXT_BASE = 0xF8003000
+
+# PAD_TO used to generate a 16kByte binary needed for the combined image
+# -> PAD_TO = TEXT_BASE + 0x4000
+PAD_TO = 0xF8007000
+
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG
+endif
+
+ifeq ($(dbcr),1)
+PLATFORM_CPPFLAGS += -DCFG_INIT_DBCR=0x8cff0000
+endif
--- /dev/null
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc:common)
+SECTIONS
+{
+ .resetvec 0xF8003FFC :
+ {
+ *(.resetvec)
+ } = 0xffff
+
+ .text :
+ {
+ start.o (.text)
+ nand_boot.o (.text)
+ ndfc.o (.text)
+
+ *(.text)
+ *(.fixup)
+ }
+ _etext = .;
+
+ .data :
+ {
+ *(.rodata*)
+ *(.data*)
+ *(.sdata*)
+ __got2_start = .;
+ *(.got2)
+ __got2_end = .;
+ }
+
+ _edata = .;
+
+ __bss_start = .;
+ .bss :
+ {
+ *(.sbss)
+ *(.bss)
+ }
+
+ _end = . ;
+}
projects / u-boot / commitdiff