--- /dev/null
+/*
+ * Copyright (c) 2005 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2006
+ * Alex Bounine , Tundra Semiconductor Corp.
+ * Roy Zang , Freescale Corp.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/****************************************************************
+ *
+ * board specific configuration options for Freescale
+ * MPC7448HPC2 (High-Performance Computing II) (Taiga) board
+ *
+ ****************************************************************/
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#undef DEBUG
+
+/* Board Configuration Definitions */
+/* MPC7448HPC2 (High-Performance Computing II) (Taiga) board */
+
+#define CONFIG_MPC7448HPC2
+
+#define CONFIG_74xx
+#define CONFIG_750FX /* this option to enable init of extended BATs */
+#define CONFIG_ALTIVEC /* undef to disable */
+
+#define CFG_BOARD_NAME "MPC7448 HPC II"
+#define CONFIG_IDENT_STRING " Freescale MPC7448 HPC II"
+
+#define CFG_OCN_CLK 133000000 /* 133 MHz */
+#define CFG_CONFIG_BUS_CLK 133000000
+
+#define CFG_CLK_SPREAD /* Enable Spread-Spectrum Clock generation */
+
+#undef CONFIG_ECC /* disable ECC support */
+
+/* Board-specific Initialization Functions to be called */
+#define CFG_BOARD_ASM_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_EARLY_INIT_R
+#define CONFIG_MISC_INIT_R
+
+/* Default MAC Addresses for on-chip GIGE Controller */
+
+#define CONFIG_ETHADDR 00:06:D2:00:00:01
+
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR 00:06:D2:00:00:02
+
+#define CONFIG_ENV_OVERWRITE
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_BAUDRATE 115200 /* console baudrate = 115000 */
+
+/*#define CFG_HUSH_PARSER */
+#undef CFG_HUSH_PARSER
+
+#define CFG_PROMPT_HUSH_PS2 "> "
+
+/* Pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+
+#define OF_CPU "PowerPC,7448@0"
+#define OF_TSI "tsi108@c0000000"
+#define OF_TBCLK (bd->bi_busfreq / 8)
+#define OF_STDOUT_PATH "/tsi108@c0000000/serial@7808"
+
+/*
+ * The following defines let you select what serial you want to use
+ * for your console driver.
+ *
+ * what to do:
+ * If you have hacked a serial cable onto the second DUART channel, change the CFG_DUART port from 1
+ * to 0 below.
+ *
+ */
+
+#define CONFIG_CONS_INDEX 1
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_CLK CFG_OCN_CLK * 8
+
+#define CFG_NS16550_COM1 (CFG_TSI108_CSR_RST_BASE+0x7808)
+#define CFG_NS16550_COM2 (CFG_TSI108_CSR_RST_BASE+0x7C08)
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
+#undef CONFIG_BOOTARGS
+/*#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo" */
+
+#if (CONFIG_BOOTDELAY >= 0)
+#define CONFIG_BOOTCOMMAND "tftpboot 0x400000 zImage.initrd.elf;\
+ setenv bootargs $(bootargs) $(bootargs_root) nfsroot=$(serverip):$(rootpath) \
+ ip=$(ipaddr):$(serverip)$(bootargs_end); bootm 0x400000; "
+
+#define CONFIG_BOOTARGS "console=ttyS0,115200"
+#endif
+
+#undef CONFIG_EXTRA_ENV_SETTINGS
+
+#define CONFIG_SERIAL "No. 1"
+
+/* Networking Configuration */
+
+#define KSEG1ADDR(a) (a) /* Needed by the rtl8139 driver */
+
+#define CONFIG_TSI108_ETH
+#define CONFIG_TSI108_ETH_NUM_PORTS 2
+
+#define CONFIG_NET_MULTI
+
+#define CONFIG_IPADDR 172.27.234.48
+#define CONFIG_SERVERIP 172.27.234.10
+#define CONFIG_NETMASK 255.255.0.0
+#define CONFIG_GATEWAYIP 172.27.255.254
+
+#define CONFIG_BOOTFILE zImage.initrd.elf
+#define CONFIG_LOADADDR 0x400000
+
+#define CONFIG_TESTDRAMDATA y
+#define CONFIG_TESTDRAMADDRESS n
+#define CONFIG_TESETDRAMWALK n
+
+/*-------------------------------------------------------------------------- */
+
+#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */
+#define CFG_LOADS_BAUD_CHANGE /* allow baudrate changes */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
+ CONFIG_BOOTP_BOOTFILESIZE)
+
+/* Flash banks JFFS2 should use */
+#define CFG_JFFS2_FIRST_BANK 1
+#define CFG_JFFS2_NUM_BANKS 1
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_ASKENV \
+ | CFG_CMD_CACHE \
+ | CFG_CMD_PCI \
+ | CFG_CMD_I2C \
+ | CFG_CMD_SDRAM \
+ | CFG_CMD_EEPROM \
+ | CFG_CMD_NET \
+ | CFG_CMD_FLASH \
+ | CFG_CMD_ENV \
+ | CFG_CMD_BSP \
+ | CFG_CMD_DHCP \
+ | CFG_CMD_PING \
+ | CFG_CMD_DATE)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*set date in u-boot*/
+#define CONFIG_RTC_M48T35A
+#define CFG_NVRAM_BASE_ADDR 0xfc000000
+#define CFG_NVRAM_SIZE 0x8000
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_VERSION_VARIABLE 1
+#define CONFIG_TSI108_I2C
+
+#define CFG_I2C_EEPROM_ADDR 0x50 /* I2C EEPROM page 1 */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+/*
+#define CFG_DRAM_TEST
+ * DRAM tests
+ * CFG_DRAM_TEST - enables the following tests.
+ *
+ * CFG_DRAM_TEST_DATA - Enables test for shorted or open data lines
+ * Environment variable 'test_dram_data' must be
+ * set to 'y'.
+ * CFG_DRAM_TEST_DATA - Enables test to verify that each word is uniquely
+ * addressable. Environment variable
+ * 'test_dram_address' must be set to 'y'.
+ * CFG_DRAM_TEST_WALK - Enables test a 64-bit walking ones pattern test.
+ * This test takes about 6 minutes to test 64 MB.
+ * Environment variable 'test_dram_walk' must be
+ * set to 'y'.
+ */
+#define CFG_DRAM_TEST
+#if defined(CFG_DRAM_TEST)
+#define CFG_MEMTEST_START 0x00400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x07c00000 /* 4 ... 124 MB in DRAM */
+#define CFG_DRAM_TEST_DATA
+#define CFG_DRAM_TEST_ADDRESS
+#define CFG_DRAM_TEST_WALK
+#endif /* CFG_DRAM_TEST */
+
+#define CFG_LOAD_ADDR 0x00400000 /* default load address */
+
+#define CFG_HZ 1000 /* decr freq: 1ms ticks */
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area
+ */
+
+/*
+ * When locking data in cache you should point the CFG_INIT_RAM_ADDRESS
+ * To an unused memory region. The stack will remain in cache until RAM
+ * is initialized
+*/
+#undef CFG_INIT_RAM_LOCK
+#define CFG_INIT_RAM_ADDR 0x07d00000 /* unused memory region */
+#define CFG_INIT_RAM_END 0x4000 /* larger space - we have SDRAM initialized */
+
+#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for init data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+
+#define CFG_SDRAM_BASE 0x00000000 /* first 256 MB of SDRAM */
+#define CFG_SDRAM1_BASE 0x10000000 /* next 256MB of SDRAM */
+
+#define CFG_SDRAM2_BASE 0x40000000 /* beginning of non-cacheable alias for SDRAM - first 256MB */
+#define CFG_SDRAM3_BASE 0x50000000 /* next Non-Cacheable 256MB of SDRAM */
+
+#define CFG_PCI_PFM_BASE 0x80000000 /* Prefetchable (cacheable) PCI/X PFM and SDRAM OCN (128MB+128MB) */
+
+#define CFG_PCI_MEM32_BASE 0xE0000000 /* Non-Cacheable PCI/X MEM and SDRAM OCN (128MB+128MB) */
+
+#define CFG_MISC_REGION_BASE 0xf0000000 /* Base Address for (PCI/X + Flash) region */
+
+#define CFG_FLASH_BASE 0xff000000 /* Base Address of Flash device */
+#define CFG_FLASH_BASE2 0xfe000000 /* Alternate Flash Base Address */
+
+#define CONFIG_VERY_BIG_RAM /* we will use up to 256M memory for cause we are short of BATS */
+
+#define PCI0_IO_BASE_BOOTM 0xfd000000
+
+#define CFG_RESET_ADDRESS 0x3fffff00
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CFG_MONITOR_BASE TEXT_BASE /* u-boot code base */
+#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc */
+
+/* Peripheral Device section */
+
+/*******************************************************
+ * Resources on the Tsi108
+ *******************************************************/
+
+#define CFG_TSI108_CSR_RST_BASE 0xC0000000 /* Tsi108 CSR base after reset */
+#define CFG_TSI108_CSR_BASE CFG_TSI108_CSR_RST_BASE /* Runtime Tsi108 CSR base */
+
+#define ENABLE_PCI_CSR_BAR /* enables access to Tsi108 CSRs from the PCI/X bus */
+
+#undef DISABLE_PBM
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_TSI108_PCI /* include tsi108 pci support */
+
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+
+#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+/* PCI MEMORY MAP section */
+
+/* PCI view of System Memory */
+#define CFG_PCI_MEMORY_BUS 0x00000000
+#define CFG_PCI_MEMORY_PHYS 0x00000000
+#define CFG_PCI_MEMORY_SIZE 0x80000000
+
+/* PCI Memory Space */
+#define CFG_PCI_MEM_BUS (CFG_PCI_MEM_PHYS)
+#define CFG_PCI_MEM_PHYS (CFG_PCI_MEM32_BASE) //CFG_PCI_MEM32_BASE = 0xE0000000
+#define CFG_PCI_MEM_SIZE 0x10000000 /* 256 MB space for PCI/X Mem + SDRAM OCN */
+
+/* PCI I/O Space */
+#define CFG_PCI_IO_BUS 0x00000000
+#define CFG_PCI_IO_PHYS 0xfa000000 /* Changed from fd000000 */
+
+#define CFG_PCI_IO_SIZE 0x01000000 /* 16MB */
+
+#define _IO_BASE 0x00000000 /* points to PCI I/O space */
+
+/* PCI Config Space mapping */
+#define CFG_PCI_CFG_BASE 0xfb000000 /* Changed from FE000000 */
+#define CFG_PCI_CFG_SIZE 0x01000000 /* 16MB */
+
+#define CFG_IBAT0U 0xFE0003FF
+#define CFG_IBAT0L 0xFE000002
+
+#define CFG_IBAT1U 0x00007FFF
+#define CFG_IBAT1L 0x00000012
+
+#define CFG_IBAT2U 0x80007FFF
+#define CFG_IBAT2L 0x80000022
+
+#define CFG_IBAT3U 0x00000000
+#define CFG_IBAT3L 0x00000000
+
+#define CFG_IBAT4U 0x00000000
+#define CFG_IBAT4L 0x00000000
+
+#define CFG_IBAT5U 0x00000000
+#define CFG_IBAT5L 0x00000000
+
+#define CFG_IBAT6U 0x00000000
+#define CFG_IBAT6L 0x00000000
+
+#define CFG_IBAT7U 0x00000000
+#define CFG_IBAT7L 0x00000000
+
+#define CFG_DBAT0U 0xE0003FFF
+#define CFG_DBAT0L 0xE000002A
+
+#define CFG_DBAT1U 0x00007FFF
+#define CFG_DBAT1L 0x00000012
+
+#define CFG_DBAT2U 0x00000000
+#define CFG_DBAT2L 0x00000000
+
+#define CFG_DBAT3U 0xC0000003
+#define CFG_DBAT3L 0xC000002A
+
+#define CFG_DBAT4U 0x00000000
+#define CFG_DBAT4L 0x00000000
+
+#define CFG_DBAT5U 0x00000000
+#define CFG_DBAT5L 0x00000000
+
+#define CFG_DBAT6U 0x00000000
+#define CFG_DBAT6L 0x00000000
+
+#define CFG_DBAT7U 0x00000000
+#define CFG_DBAT7L 0x00000000
+
+/* I2C addresses for the two DIMM SPD chips */
+#define DIMM0_I2C_ADDR 0x51
+#define DIMM1_I2C_ADDR 0x52
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8<<20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* Flash can be at one of two addresses */
+#define FLASH_BANK_SIZE 0x01000000 /* 16 MB Total */
+#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2}
+
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_FLASH_CFI_SWAP
+
+#define PHYS_FLASH_SIZE 0x01000000
+#define CFG_MAX_FLASH_SECT (128)
+
+#define CFG_ENV_IS_IN_NVRAM
+#define CFG_ENV_ADDR 0xFC000000
+
+#define CFG_ENV_OFFSET 0x00000000 /* Offset of Environment Sector */
+#define CFG_ENV_SIZE 0x00000400 /* Total Size of Environment Space */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * L2CR setup -- make sure this is right for your board!
+ * look in include/mpc74xx.h for the defines used here
+ */
+#undef CFG_L2
+
+#define L2_INIT 0
+#define L2_ENABLE (L2_INIT | L2CR_L2E)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#define CFG_EXCEPTION_AFTER_RELOCATE
+#define CFG_SERIAL_HANG_IN_EXCEPTION
+#endif /* __CONFIG_H */
projects / u-boot / commitdiff