--- /dev/null
+/*
+ * Copyright 2007 Wind River Systems <www.windriver.com>
+ * Copyright 2007 Embedded Specialties, Inc.
+ * Joe Hamman <joe.hamman@embeddedspecialties.com>
+ *
+ * Copyright 2006 Freescale Semiconductor.
+ *
+ * Srikanth Srinivasan (srikanth.srinivasan@freescale.com)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * SBC8641D board configuration file
+ *
+ * Make sure you change the MAC address and other network params first,
+ * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_MPC86xx 1 /* MPC86xx */
+#define CONFIG_MPC8641 1 /* MPC8641 specific */
+#define CONFIG_SBC8641D 1 /* SBC8641D board specific */
+#define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */
+#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */
+
+#ifdef RUN_DIAG
+#define CFG_DIAG_ADDR 0xff800000
+#endif
+
+#define CFG_RESET_ADDRESS 0xfff00100
+
+#undef CONFIG_PCI
+#define CONFIG_FSL_PCI_INIT 1
+
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+
+#undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup*/
+#undef CONFIG_DDR_DLL /* possible DLL fix needed */
+#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
+#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+#define CONFIG_NUM_DDR_CONTROLLERS 2
+#define CACHE_LINE_INTERLEAVING 0x20000000
+#define PAGE_INTERLEAVING 0x21000000
+#define BANK_INTERLEAVING 0x22000000
+#define SUPER_BANK_INTERLEAVING 0x23000000
+
+
+#define CONFIG_ALTIVEC 1
+
+/*
+ * L2CR setup -- make sure this is right for your board!
+ */
+#define CFG_L2
+#define L2_INIT 0
+#define L2_ENABLE (L2CR_L2E)
+
+#ifndef CONFIG_SYS_CLK_FREQ
+#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
+
+#undef CFG_DRAM_TEST /* memory test, takes time */
+#define CFG_MEMTEST_START 0x00200000 /* memtest region */
+#define CFG_MEMTEST_END 0x00400000
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CFG_CCSRBAR 0xf8000000 /* relocated CCSRBAR */
+#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
+#define CFG_DDR_SDRAM_BASE2 0x10000000 /* DDR bank 2 */
+#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+#define CFG_SDRAM_BASE2 CFG_DDR_SDRAM_BASE2
+#define CONFIG_VERY_BIG_RAM
+
+#define MPC86xx_DDR_SDRAM_CLK_CNTL
+
+#if defined(CONFIG_SPD_EEPROM)
+ /*
+ * Determine DDR configuration from I2C interface.
+ */
+ #define SPD_EEPROM_ADDRESS1 0x51 /* DDR DIMM */
+ #define SPD_EEPROM_ADDRESS2 0x52 /* DDR DIMM */
+ #define SPD_EEPROM_ADDRESS3 0x53 /* DDR DIMM */
+ #define SPD_EEPROM_ADDRESS4 0x54 /* DDR DIMM */
+
+#else
+ /*
+ * Manually set up DDR1 & DDR2 parameters
+ */
+
+ #define CFG_SDRAM_SIZE 512 /* DDR is 512MB */
+
+ #define CFG_DDR_CS0_BNDS 0x0000000F
+ #define CFG_DDR_CS1_BNDS 0x00000000
+ #define CFG_DDR_CS2_BNDS 0x00000000
+ #define CFG_DDR_CS3_BNDS 0x00000000
+ #define CFG_DDR_CS0_CONFIG 0x80010102
+ #define CFG_DDR_CS1_CONFIG 0x00000000
+ #define CFG_DDR_CS2_CONFIG 0x00000000
+ #define CFG_DDR_CS3_CONFIG 0x00000000
+ #define CFG_DDR_EXT_REFRESH 0x00000000
+ #define CFG_DDR_TIMING_0 0x00220802
+ #define CFG_DDR_TIMING_1 0x38377322
+ #define CFG_DDR_TIMING_2 0x002040c7
+ #define CFG_DDR_CFG_1A 0x43008008
+ #define CFG_DDR_CFG_2 0x24401000
+ #define CFG_DDR_MODE_1 0x23c00542
+ #define CFG_DDR_MODE_2 0x00000000
+ #define CFG_DDR_MODE_CTL 0x00000000
+ #define CFG_DDR_INTERVAL 0x05080100
+ #define CFG_DDR_DATA_INIT 0x00000000
+ #define CFG_DDR_CLK_CTRL 0x03800000
+ #define CFG_DDR_CFG_1B 0xC3008008
+
+ #define CFG_DDR2_CS0_BNDS 0x0010001F
+ #define CFG_DDR2_CS1_BNDS 0x00000000
+ #define CFG_DDR2_CS2_BNDS 0x00000000
+ #define CFG_DDR2_CS3_BNDS 0x00000000
+ #define CFG_DDR2_CS0_CONFIG 0x80010102
+ #define CFG_DDR2_CS1_CONFIG 0x00000000
+ #define CFG_DDR2_CS2_CONFIG 0x00000000
+ #define CFG_DDR2_CS3_CONFIG 0x00000000
+ #define CFG_DDR2_EXT_REFRESH 0x00000000
+ #define CFG_DDR2_TIMING_0 0x00220802
+ #define CFG_DDR2_TIMING_1 0x38377322
+ #define CFG_DDR2_TIMING_2 0x002040c7
+ #define CFG_DDR2_CFG_1A 0x43008008
+ #define CFG_DDR2_CFG_2 0x24401000
+ #define CFG_DDR2_MODE_1 0x23c00542
+ #define CFG_DDR2_MODE_2 0x00000000
+ #define CFG_DDR2_MODE_CTL 0x00000000
+ #define CFG_DDR2_INTERVAL 0x05080100
+ #define CFG_DDR2_DATA_INIT 0x00000000
+ #define CFG_DDR2_CLK_CTRL 0x03800000
+ #define CFG_DDR2_CFG_1B 0xC3008008
+
+
+#endif
+
+/* #define CFG_ID_EEPROM 1
+#define ID_EEPROM_ADDR 0x57 */
+
+/*
+ * The SBC8641D contains 16MB flash space at ff000000.
+ */
+#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */
+
+/* Flash */
+#define CFG_BR0_PRELIM 0xff001001 /* port size 16bit */
+#define CFG_OR0_PRELIM 0xff006e65 /* 16MB Boot Flash area */
+
+/* 64KB EEPROM */
+#define CFG_BR1_PRELIM 0xf0000801 /* port size 16bit */
+#define CFG_OR1_PRELIM 0xffff6e65 /* 64K EEPROM area */
+
+/* EPLD - User switches, board id, LEDs */
+#define CFG_BR2_PRELIM 0xf1000801 /* port size 16bit */
+#define CFG_OR2_PRELIM 0xfff06e65 /* EPLD (switches, board ID, LEDs) area */
+
+/* Local bus SDRAM 128MB */
+#define CFG_BR3_PRELIM 0xe0001861 /* port size ?bit */
+#define CFG_OR3_PRELIM 0xfc006cc0 /* 128MB local bus SDRAM area (1st half) */
+#define CFG_BR4_PRELIM 0xe4001861 /* port size ?bit */
+#define CFG_OR4_PRELIM 0xfc006cc0 /* 128MB local bus SDRAM area (2nd half) */
+
+/* Disk on Chip (DOC) 128MB */
+#define CFG_BR5_PRELIM 0xe8001001 /* port size ?bit */
+#define CFG_OR5_PRELIM 0xf8006e65 /* 128MB local bus SDRAM area (2nd half) */
+
+/* LCD */
+#define CFG_BR6_PRELIM 0xf4000801 /* port size ?bit */
+#define CFG_OR6_PRELIM 0xfff06e65 /* 128MB local bus SDRAM area (2nd half) */
+
+/* Control logic & misc peripherals */
+#define CFG_BR7_PRELIM 0xf2000801 /* port size ?bit */
+#define CFG_OR7_PRELIM 0xfff06e65 /* 128MB local bus SDRAM area (2nd half) */
+
+#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
+#define CFG_MAX_FLASH_SECT 131 /* sectors per device */
+
+#undef CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_WRITE_SWAPPED_DATA
+#define CFG_FLASH_EMPTY_INFO
+#define CFG_FLASH_PROTECTION
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK 1
+#ifndef CFG_INIT_RAM_LOCK
+#define CFG_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */
+#else
+#define CFG_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */
+#endif
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_CLK get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/*
+ * Pass open firmware flat tree to kernel
+ */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+
+#define OF_CPU "PowerPC,8641@0"
+#define OF_SOC "soc@f8000000"
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc@f8000000/serial@4500"
+
+#define CFG_64BIT_VSPRINTF 1
+#define CFG_64BIT_STRTOUL 1
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3100
+
+/*
+ * RapidIO MMU
+ */
+#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
+#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE
+#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI1_MEM_BASE 0x80000000
+#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI1_IO_BASE 0xe2000000
+#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
+#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
+
+/* PCI view of System Memory */
+#define CFG_PCI_MEMORY_BUS 0x00000000
+#define CFG_PCI_MEMORY_PHYS 0x00000000
+#define CFG_PCI_MEMORY_SIZE 0x80000000
+
+#define CFG_PCI2_MEM_BASE 0xa0000000
+#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
+#define CFG_PCI2_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PCI2_IO_BASE 0xe3000000
+#define CFG_PCI2_IO_PHYS CFG_PCI2_IO_BASE
+#define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */
+
+#if defined(CONFIG_PCI)
+
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+
+#undef CFG_SCSI_SCAN_BUS_REVERSE
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+
+#if !defined(CONFIG_PCI_PNP)
+ #define PCI_ENET0_IOADDR 0xe0000000
+ #define PCI_ENET0_MEMADDR 0xe0000000
+ #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
+#endif
+
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+
+#define CONFIG_DOS_PARTITION
+#undef CONFIG_SCSI_AHCI
+
+#ifdef CONFIG_SCSI_AHCI
+#define CONFIG_SATA_ULI5288
+#define CFG_SCSI_MAX_SCSI_ID 4
+#define CFG_SCSI_MAX_LUN 1
+#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
+#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE
+#endif
+
+#endif /* CONFIG_PCI */
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 1
+#endif
+
+/* #define CONFIG_MII 1 */ /* MII PHY management */
+
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "eTSEC1"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "eTSEC2"
+#define CONFIG_TSEC3 1
+#define CONFIG_TSEC3_NAME "eTSEC3"
+#define CONFIG_TSEC4 1
+#define CONFIG_TSEC4_NAME "eTSEC4"
+
+#define TSEC1_PHY_ADDR 0x1F
+#define TSEC2_PHY_ADDR 0x00
+#define TSEC3_PHY_ADDR 0x01
+#define TSEC4_PHY_ADDR 0x02
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define TSEC3_PHYIDX 0
+#define TSEC4_PHYIDX 0
+
+#define CFG_TBIPA_VALUE 0x1e /* Set TBI address not to conflict with TSEC1_PHY_ADDR */
+
+#define CONFIG_ETHPRIME "eTSEC1"
+
+#endif /* CONFIG_TSEC_ENET */
+
+/*
+ * BAT0 2G Cacheable, non-guarded
+ * 0x0000_0000 2G DDR
+ */
+#define CFG_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP)
+#define CFG_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE )
+#define CFG_IBAT0U CFG_DBAT0U
+
+/*
+ * BAT1 1G Cache-inhibited, guarded
+ * 0x8000_0000 512M PCI-Express 1 Memory
+ * 0xa000_0000 512M PCI-Express 2 Memory
+ * Changed it for operating from 0xd0000000
+ */
+#define CFG_DBAT1L ( CFG_PCI1_MEM_BASE | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT1U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT1U CFG_DBAT1U
+
+/*
+ * BAT2 512M Cache-inhibited, guarded
+ * 0xc000_0000 512M RapidIO Memory
+ */
+#define CFG_DBAT2L (CFG_RIO_MEM_BASE | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT2U (CFG_RIO_MEM_BASE | BATU_BL_512M | BATU_VS | BATU_VP)
+#define CFG_IBAT2L (CFG_RIO_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT2U CFG_DBAT2U
+
+/*
+ * BAT3 4M Cache-inhibited, guarded
+ * 0xf800_0000 4M CCSR
+ */
+#define CFG_DBAT3L ( CFG_CCSRBAR | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT3U (CFG_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP)
+#define CFG_IBAT3L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT3U CFG_DBAT3U
+
+/*
+ * BAT4 32M Cache-inhibited, guarded
+ * 0xe200_0000 16M PCI-Express 1 I/O
+ * 0xe300_0000 16M PCI-Express 2 I/0
+ * Note that this is at 0xe0000000
+ */
+#define CFG_DBAT4L ( CFG_PCI1_IO_BASE | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT4U (CFG_PCI1_IO_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CFG_IBAT4L (CFG_PCI1_IO_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT4U CFG_DBAT4U
+
+/*
+ * BAT5 128K Cacheable, non-guarded
+ * 0xe401_0000 128K Init RAM for stack in the CPU DCache (no backing memory)
+ */
+#define CFG_DBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_DBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CFG_IBAT5L CFG_DBAT5L
+#define CFG_IBAT5U CFG_DBAT5U
+
+/*
+ * BAT6 32M Cache-inhibited, guarded
+ * 0xfe00_0000 32M FLASH
+ */
+#define CFG_DBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT6U ((CFG_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CFG_IBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_IBAT6U CFG_DBAT6U
+
+#define CFG_DBAT7L 0x00000000
+#define CFG_DBAT7U 0x00000000
+#define CFG_IBAT7L 0x00000000
+#define CFG_IBAT7U 0x00000000
+
+/*
+ * Environment
+ */
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
+#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
+#define CFG_ENV_SIZE 0x2000
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#include <config_cmd_default.h>
+ #define CONFIG_CMD_PING
+ #define CONFIG_CMD_I2C
+
+#if defined(CONFIG_PCI)
+ #define CONFIG_CMD_PCI
+#endif
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_LOAD_ADDR 0x2000000 /* default load address */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+ #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+ #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE 32768
+#define CFG_CACHELINE_SIZE 32
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+/* The mac addresses for all ethernet interface */
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_ETHADDR 02:E0:0C:00:00:01
+#define CONFIG_ETH1ADDR 02:E0:0C:00:01:FD
+#define CONFIG_ETH2ADDR 02:E0:0C:00:02:FD
+#define CONFIG_ETH3ADDR 02:E0:0C:00:03:FD
+#endif
+
+#define CONFIG_HAS_ETH1 1
+#define CONFIG_HAS_ETH2 1
+#define CONFIG_HAS_ETH3 1
+
+#define CONFIG_IPADDR 192.168.0.50
+
+#define CONFIG_HOSTNAME sbc8641d
+#define CONFIG_ROOTPATH /opt/eldk/ppc_74xx
+#define CONFIG_BOOTFILE uImage
+
+#define CONFIG_SERVERIP 192.168.0.2
+#define CONFIG_GATEWAYIP 192.168.0.1
+#define CONFIG_NETMASK 255.255.255.0
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR 1000000
+
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=uRamdisk\0" \
+ "dtbaddr=400000\0" \
+ "dtbfile=sbc8641d.dtb\0" \
+ "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
+ "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
+ "maxcpus=1"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $dtbaddr $dtbfile;" \
+ "bootm $loadaddr - $dtbaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $dtbaddr $dtbfile;" \
+ "bootm $loadaddr $ramdiskaddr $dtbaddr"
+
+#define CONFIG_FLASHBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "bootm ffd00000 ffb00000 ffa00000"
+
+#define CONFIG_BOOTCOMMAND CONFIG_FLASHBOOTCOMMAND
+
+#endif /* __CONFIG_H */
projects / u-boot / commitdiff