tegra_mmc_init() now parses the DT info for bus width, WP/CD GPIOs, etc.
Tested on Seaboard, fully functional.
Tamonten boards (medcom-wide, plutux, and tec) use a different/new
dtsi file w/common settings.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
#ifndef _TEGRA_MMC_H_
#define _TEGRA_MMC_H_
-int tegra_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio);
+void tegra_mmc_init(void);
#endif /* _TEGRA_MMC_H_ */
#define TEGRA_SDMMC3_BASE 0xC8000400
#define TEGRA_SDMMC4_BASE 0xC8000600
+#define MAX_HOSTS 4 /* Max number of 'hosts'/controllers */
+
#ifndef __ASSEMBLY__
struct tegra_mmc {
unsigned int sysad; /* _SYSTEM_ADDRESS_0 */
struct mmc_host {
struct tegra_mmc *reg;
+ int id; /* device id/number, 0-3 */
+ int enabled; /* 1 to enable, 0 to disable */
+ int width; /* Bus Width, 1, 4 or 8 */
+ enum periph_id mmc_id; /* Peripheral ID: PERIPH_ID_... */
+ struct fdt_gpio_state cd_gpio; /* Change Detect GPIO */
+ struct fdt_gpio_state pwr_gpio; /* Power GPIO */
+ struct fdt_gpio_state wp_gpio; /* Write Protect GPIO */
unsigned int version; /* SDHCI spec. version */
unsigned int clock; /* Current clock (MHz) */
- unsigned int base; /* Base address, SDMMC1/2/3/4 */
- enum periph_id mmc_id; /* Peripheral ID: PERIPH_ID_... */
- int pwr_gpio; /* Power GPIO */
- int cd_gpio; /* Change Detect GPIO */
};
#endif /* __ASSEMBLY__ */
#include <asm/arch/tegra.h>
#include <asm/arch-tegra/board.h>
#include <asm/arch-tegra/clk_rst.h>
-#include <asm/arch-tegra/mmc.h>
#include <asm/arch-tegra/sys_proto.h>
#include <asm/arch-tegra/uart.h>
-#ifdef CONFIG_TEGRA_MMC
-#include <mmc.h>
-#endif
-
#ifdef CONFIG_BOARD_EARLY_INIT_F
void gpio_early_init(void)
* Routine: pin_mux_mmc
* Description: setup the pin muxes/tristate values for the SDMMC(s)
*/
-static void pin_mux_mmc(void)
+void pin_mux_mmc(void)
{
funcmux_select(PERIPH_ID_SDMMC4, FUNCMUX_SDMMC4_ATB_GMA_GME_8_BIT);
/* for write-protect GPIO PI6 */
/* for CD GPIO PH2 */
pinmux_tristate_disable(PINGRP_ATD);
}
-
-/* this is a weak define that we are overriding */
-int board_mmc_init(bd_t *bd)
-{
- /* Enable muxes, etc. for SDMMC controllers */
- pin_mux_mmc();
-
- /* init dev 0, SD slot, with 4-bit bus */
- tegra_mmc_init(0, 4, GPIO_PI6, GPIO_PH2);
-
- return 0;
-}
#endif
#include <asm/io.h>
#include <asm/arch/tegra.h>
#include <asm/arch/pinmux.h>
-#include <asm/arch-tegra/mmc.h>
#include <asm/gpio.h>
-#ifdef CONFIG_TEGRA_MMC
-#include <mmc.h>
-#endif
-
#ifdef CONFIG_TEGRA_MMC
/*
* Routine: pin_mux_mmc
* Description: setup the pin muxes/tristate values for the SDMMC(s)
*/
-static void pin_mux_mmc(void)
+void pin_mux_mmc(void)
{
/* SDMMC4: config 3, x8 on 2nd set of pins */
pinmux_set_func(PINGRP_ATB, PMUX_FUNC_SDIO4);
/* For CD GPIO PV5 */
pinmux_tristate_disable(PINGRP_GPV);
}
-
-/* this is a weak define that we are overriding */
-int board_mmc_init(bd_t *bd)
-{
- debug("board_mmc_init called\n");
-
- /* Enable muxes, etc. for SDMMC controllers */
- pin_mux_mmc();
-
- debug("board_mmc_init: init eMMC\n");
- /* init dev 0, eMMC chip, with 8-bit bus */
- tegra_mmc_init(0, 8, -1, -1);
-
- debug("board_mmc_init: init SD slot\n");
- /* init dev 3, SD slot, with 4-bit bus */
- tegra_mmc_init(3, 4, GPIO_PV1, GPIO_PV5);
-
- return 0;
-}
#endif
#ifdef CONFIG_LCD
#include <asm/arch/clock.h>
#include <asm/arch/funcmux.h>
#include <asm/arch/pinmux.h>
-#include <asm/arch-tegra/mmc.h>
#include <asm/gpio.h>
#include <i2c.h>
-#ifdef CONFIG_TEGRA_MMC
-#include <mmc.h>
-#endif
void pin_mux_usb(void)
{
* Routine: pin_mux_mmc
* Description: setup the pin muxes/tristate values for the SDMMC(s)
*/
-static void pin_mux_mmc(void)
+void pin_mux_mmc(void)
{
funcmux_select(PERIPH_ID_SDMMC1, FUNCMUX_SDMMC1_SDIO1_4BIT);
funcmux_select(PERIPH_ID_SDMMC4, FUNCMUX_SDMMC4_ATB_GMA_4_BIT);
/* For CD GPIO PP1 */
pinmux_tristate_disable(PINGRP_DAP3);
}
-
-/* this is a weak define that we are overriding */
-int board_mmc_init(bd_t *bd)
-{
- debug("board_mmc_init called\n");
-
- /* Enable muxes, etc. for SDMMC controllers */
- pin_mux_mmc();
-
- /* init dev 0 (SDMMC4), (micro-SD slot) with 4-bit bus */
- tegra_mmc_init(0, 4, -1, GPIO_PP1);
-
- /* init dev 3 (SDMMC1), (SD slot) with 4-bit bus */
- tegra_mmc_init(3, 4, -1, -1);
-
- return 0;
-}
#ifdef CONFIG_USB_EHCI_TEGRA
#include <asm/arch-tegra/usb.h>
#endif
+#ifdef CONFIG_TEGRA_MMC
+#include <asm/arch-tegra/mmc.h>
+#endif
#include <i2c.h>
#include <spi.h>
#include "emc.h"
#endif
return 0;
}
+
+#if defined(CONFIG_TEGRA_MMC)
+void __pin_mux_mmc(void)
+{
+}
+
+void pin_mux_mmc(void) __attribute__((weak, alias("__pin_mux_mmc")));
+
+/* this is a weak define that we are overriding */
+int board_mmc_init(bd_t *bd)
+{
+ debug("%s called\n", __func__);
+
+ /* Enable muxes, etc. for SDMMC controllers */
+ pin_mux_mmc();
+
+ debug("%s: init MMC\n", __func__);
+ tegra_mmc_init();
+
+ return 0;
+}
+#endif
#include <asm/arch/funcmux.h>
#include <asm/arch/pinmux.h>
#include <asm/arch/tegra.h>
-#include <asm/arch-tegra/mmc.h>
#include <asm/gpio.h>
-#ifdef CONFIG_TEGRA_MMC
-#include <mmc.h>
-#endif
-
#ifdef CONFIG_TEGRA_MMC
/*
* Routine: pin_mux_mmc
* Description: setup the pin muxes/tristate values for the SDMMC(s)
*/
-static void pin_mux_mmc(void)
+void pin_mux_mmc(void)
{
funcmux_select(PERIPH_ID_SDMMC4, FUNCMUX_SDMMC4_ATB_GMA_GME_8_BIT);
funcmux_select(PERIPH_ID_SDMMC2, FUNCMUX_SDMMC2_DTA_DTD_8BIT);
/* For CD GPIO PI5 */
pinmux_tristate_disable(PINGRP_ATC);
}
-
-/* this is a weak define that we are overriding */
-int board_mmc_init(bd_t *bd)
-{
- debug("board_mmc_init called\n");
-
- /* Enable muxes, etc. for SDMMC controllers */
- pin_mux_mmc();
-
- debug("board_mmc_init: init SD slot J26\n");
- /* init dev 0, SD slot J26, with 8-bit bus */
- tegra_mmc_init(0, 8, GPIO_PI6, GPIO_PH2);
-
- debug("board_mmc_init: init SD slot J5\n");
- /* init dev 2, SD slot J5, with 4-bit bus */
- tegra_mmc_init(2, 4, GPIO_PT3, GPIO_PI5);
-
- return 0;
-}
#endif
void pin_mux_usb(void)
#include <asm/arch/funcmux.h>
#include <asm/arch/gpio.h>
#include <asm/arch/pinmux.h>
-#include <asm/arch-tegra/mmc.h>
#include <asm/gpio.h>
-#ifdef CONFIG_TEGRA_MMC
-#include <mmc.h>
-#endif
/* TODO: Remove this code when the SPI switch is working */
#if !defined(CONFIG_SPI_UART_SWITCH) && (CONFIG_MACH_TYPE != MACH_TYPE_VENTANA)
* Routine: pin_mux_mmc
* Description: setup the pin muxes/tristate values for the SDMMC(s)
*/
-static void pin_mux_mmc(void)
+void pin_mux_mmc(void)
{
funcmux_select(PERIPH_ID_SDMMC4, FUNCMUX_SDMMC4_ATB_GMA_GME_8_BIT);
funcmux_select(PERIPH_ID_SDMMC3, FUNCMUX_SDMMC3_SDB_4BIT);
/* For CD GPIO PI5 */
pinmux_tristate_disable(PINGRP_ATC);
}
-
-/* this is a weak define that we are overriding */
-int board_mmc_init(bd_t *bd)
-{
- debug("board_mmc_init called\n");
-
- /* Enable muxes, etc. for SDMMC controllers */
- pin_mux_mmc();
-
- debug("board_mmc_init: init eMMC\n");
- /* init dev 0, eMMC chip, with 8-bit bus */
- tegra_mmc_init(0, 8, -1, -1);
-
- debug("board_mmc_init: init SD slot\n");
- /* init dev 1, SD slot, with 4-bit bus */
- tegra_mmc_init(1, 4, GPIO_PI6, GPIO_PI5);
-
- return 0;
-}
#endif
void pin_mux_usb(void)
#include <asm/arch/clock.h>
#include <asm/arch/funcmux.h>
#include <asm/arch/pinmux.h>
-#include <asm/arch-tegra/mmc.h>
#include <asm/gpio.h>
#include <i2c.h>
-#ifdef CONFIG_TEGRA_MMC
-#include <mmc.h>
-#endif
-
+#ifdef CONFIG_TEGRA_MMC
/*
* Routine: pin_mux_mmc
* Description: setup the pin muxes/tristate values for the SDMMC(s)
*/
-static void pin_mux_mmc(void)
-{
- funcmux_select(PERIPH_ID_SDMMC3, FUNCMUX_SDMMC3_SDB_SLXA_8BIT);
- funcmux_select(PERIPH_ID_SDMMC4, FUNCMUX_SDMMC4_ATC_ATD_8BIT);
-}
-
-/* this is a weak define that we are overriding */
-int board_mmc_init(bd_t *bd)
+void pin_mux_mmc(void)
{
uchar val;
int ret;
- debug("board_mmc_init called\n");
-
/* Turn on MAX8907B LDO12 to 2.8V for J40 power */
ret = i2c_set_bus_num(0);
if (ret)
if (ret)
printf("i2c_write 0 0x3c 0x44 failed: %d\n", ret);
- /* Enable muxes, etc. for SDMMC controllers */
- pin_mux_mmc();
-
- /* init dev 0 (SDMMC4), (J29 "HSMMC") with 8-bit bus */
- tegra_mmc_init(0, 8, -1, -1);
-
- /* init dev 1 (SDMMC3), (J40 "SDIO3") with 8-bit bus */
- tegra_mmc_init(1, 8, -1, -1);
-
- return 0;
+ funcmux_select(PERIPH_ID_SDMMC3, FUNCMUX_SDMMC3_SDB_SLXA_8BIT);
+ funcmux_select(PERIPH_ID_SDMMC4, FUNCMUX_SDMMC4_ATC_ATD_8BIT);
}
+#endif
/* this is a weak define that we are overriding */
void pin_mux_usb(void)
#include <asm/arch/funcmux.h>
#include <asm/arch/pinmux.h>
#include <asm/arch-tegra/board.h>
-#include <asm/arch-tegra/mmc.h>
#include "../colibri_t20-common/colibri_t20-common.h"
#endif
#ifdef CONFIG_TEGRA_MMC
-int board_mmc_init(bd_t *bd)
+/*
+ * Routine: pin_mux_mmc
+ * Description: setup the pin muxes/tristate values for the SDMMC(s)
+ */
+void pin_mux_mmc(void)
{
funcmux_select(PERIPH_ID_SDMMC4, FUNCMUX_SDMMC4_ATB_GMA_4_BIT);
pinmux_tristate_disable(PINGRP_GMB);
-
- tegra_mmc_init(0, 4, -1, GPIO_PC7);
-
- return 0;
}
#endif
* (C) Copyright 2009 SAMSUNG Electronics
* Minkyu Kang <mk7.kang@samsung.com>
* Jaehoon Chung <jh80.chung@samsung.com>
- * Portions Copyright 2011-2012 NVIDIA Corporation
+ * Portions Copyright 2011-2013 NVIDIA Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
#include <bouncebuf.h>
#include <common.h>
+#include <fdtdec.h>
#include <asm/gpio.h>
#include <asm/io.h>
#include <asm/arch/clock.h>
#include <asm/arch-tegra/tegra_mmc.h>
#include <mmc.h>
-/* support 4 mmc hosts */
-struct mmc mmc_dev[4];
-struct mmc_host mmc_host[4];
+DECLARE_GLOBAL_DATA_PTR;
+struct mmc mmc_dev[MAX_HOSTS];
+struct mmc_host mmc_host[MAX_HOSTS];
-/**
- * Get the host address and peripheral ID for a device. Devices are numbered
- * from 0 to 3.
- *
- * @param host Structure to fill in (base, reg, mmc_id)
- * @param dev_index Device index (0-3)
- */
-static void tegra_get_setup(struct mmc_host *host, int dev_index)
-{
- debug("tegra_get_setup: dev_index = %d\n", dev_index);
-
- switch (dev_index) {
- case 1:
- host->base = TEGRA_SDMMC3_BASE;
- host->mmc_id = PERIPH_ID_SDMMC3;
- break;
- case 2:
- host->base = TEGRA_SDMMC2_BASE;
- host->mmc_id = PERIPH_ID_SDMMC2;
- break;
- case 3:
- host->base = TEGRA_SDMMC1_BASE;
- host->mmc_id = PERIPH_ID_SDMMC1;
- break;
- case 0:
- default:
- host->base = TEGRA_SDMMC4_BASE;
- host->mmc_id = PERIPH_ID_SDMMC4;
- break;
- }
-
- host->reg = (struct tegra_mmc *)host->base;
-}
+#ifndef CONFIG_OF_CONTROL
+#error "Please enable device tree support to use this driver"
+#endif
static void mmc_prepare_data(struct mmc_host *host, struct mmc_data *data,
struct bounce_buffer *bbstate)
debug("tegra_mmc_getcd called\n");
- if (host->cd_gpio >= 0)
- return !gpio_get_value(host->cd_gpio);
+ if (fdt_gpio_isvalid(&host->cd_gpio))
+ return fdtdec_get_gpio(&host->cd_gpio);
return 1;
}
-int tegra_mmc_init(int dev_index, int bus_width, int pwr_gpio, int cd_gpio)
+static int do_mmc_init(int dev_index)
{
struct mmc_host *host;
char gpusage[12]; /* "SD/MMCn PWR" or "SD/MMCn CD" */
struct mmc *mmc;
- debug(" tegra_mmc_init: index %d, bus width %d "
- "pwr_gpio %d cd_gpio %d\n",
- dev_index, bus_width, pwr_gpio, cd_gpio);
-
+ /* DT should have been read & host config filled in */
host = &mmc_host[dev_index];
+ if (!host->enabled)
+ return -1;
- host->clock = 0;
- host->pwr_gpio = pwr_gpio;
- host->cd_gpio = cd_gpio;
- tegra_get_setup(host, dev_index);
+ debug(" do_mmc_init: index %d, bus width %d "
+ "pwr_gpio %d cd_gpio %d\n",
+ dev_index, host->width,
+ host->pwr_gpio.gpio, host->cd_gpio.gpio);
+ host->clock = 0;
clock_start_periph_pll(host->mmc_id, CLOCK_ID_PERIPH, 20000000);
- if (host->pwr_gpio >= 0) {
+ if (fdt_gpio_isvalid(&host->pwr_gpio)) {
sprintf(gpusage, "SD/MMC%d PWR", dev_index);
- gpio_request(host->pwr_gpio, gpusage);
- gpio_direction_output(host->pwr_gpio, 1);
+ gpio_request(host->pwr_gpio.gpio, gpusage);
+ gpio_direction_output(host->pwr_gpio.gpio, 1);
+ debug(" Power GPIO name = %s\n", host->pwr_gpio.name);
}
- if (host->cd_gpio >= 0) {
+ if (fdt_gpio_isvalid(&host->cd_gpio)) {
sprintf(gpusage, "SD/MMC%d CD", dev_index);
- gpio_request(host->cd_gpio, gpusage);
- gpio_direction_input(host->cd_gpio);
+ gpio_request(host->cd_gpio.gpio, gpusage);
+ gpio_direction_input(host->cd_gpio.gpio);
+ debug(" CD GPIO name = %s\n", host->cd_gpio.name);
}
mmc = &mmc_dev[dev_index];
mmc->voltages = MMC_VDD_32_33 | MMC_VDD_33_34 | MMC_VDD_165_195;
mmc->host_caps = 0;
- if (bus_width == 8)
+ if (host->width == 8)
mmc->host_caps |= MMC_MODE_8BIT;
- if (bus_width >= 4)
+ if (host->width >= 4)
mmc->host_caps |= MMC_MODE_4BIT;
mmc->host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS | MMC_MODE_HC;
* low-speed SDIO card frequency (actually 400KHz)
* max freq is highest HS eMMC clock as per the SD/MMC spec
* (actually 52MHz)
- * Both of these are the closest equivalents w/216MHz source
- * clock and Tegra SDMMC divisors.
*/
mmc->f_min = 375000;
mmc->f_max = 48000000;
return 0;
}
+
+/**
+ * Get the host address and peripheral ID for a node.
+ *
+ * @param blob fdt blob
+ * @param node Device index (0-3)
+ * @param host Structure to fill in (reg, width, mmc_id)
+ */
+static int mmc_get_config(const void *blob, int node, struct mmc_host *host)
+{
+ debug("%s: node = %d\n", __func__, node);
+
+ host->enabled = fdtdec_get_is_enabled(blob, node);
+
+ host->reg = (struct tegra_mmc *)fdtdec_get_addr(blob, node, "reg");
+ if ((fdt_addr_t)host->reg == FDT_ADDR_T_NONE) {
+ debug("%s: no sdmmc base reg info found\n", __func__);
+ return -FDT_ERR_NOTFOUND;
+ }
+
+ host->mmc_id = clock_decode_periph_id(blob, node);
+ if (host->mmc_id == PERIPH_ID_NONE) {
+ debug("%s: could not decode periph id\n", __func__);
+ return -FDT_ERR_NOTFOUND;
+ }
+
+ /*
+ * NOTE: mmc->bus_width is determined by mmc.c dynamically.
+ * TBD: Override it with this value?
+ */
+ host->width = fdtdec_get_int(blob, node, "bus-width", 0);
+ if (!host->width)
+ debug("%s: no sdmmc width found\n", __func__);
+
+ /* These GPIOs are optional */
+ fdtdec_decode_gpio(blob, node, "cd-gpios", &host->cd_gpio);
+ fdtdec_decode_gpio(blob, node, "wp-gpios", &host->wp_gpio);
+ fdtdec_decode_gpio(blob, node, "power-gpios", &host->pwr_gpio);
+
+ debug("%s: found controller at %p, width = %d, periph_id = %d\n",
+ __func__, host->reg, host->width, host->mmc_id);
+ return 0;
+}
+
+/*
+ * Process a list of nodes, adding them to our list of SDMMC ports.
+ *
+ * @param blob fdt blob
+ * @param node_list list of nodes to process (any <=0 are ignored)
+ * @param count number of nodes to process
+ * @return 0 if ok, -1 on error
+ */
+static int process_nodes(const void *blob, int node_list[], int count)
+{
+ struct mmc_host *host;
+ int i, node;
+
+ debug("%s: count = %d\n", __func__, count);
+
+ /* build mmc_host[] for each controller */
+ for (i = 0; i < count; i++) {
+ node = node_list[i];
+ if (node <= 0)
+ continue;
+
+ host = &mmc_host[i];
+ host->id = i;
+
+ if (mmc_get_config(blob, node, host)) {
+ printf("%s: failed to decode dev %d\n", __func__, i);
+ return -1;
+ }
+ do_mmc_init(i);
+ }
+ return 0;
+}
+
+void tegra_mmc_init(void)
+{
+ int node_list[MAX_HOSTS], count;
+ const void *blob = gd->fdt_blob;
+ debug("%s entry\n", __func__);
+
+ count = fdtdec_find_aliases_for_id(blob, "sdhci",
+ COMPAT_NVIDIA_TEGRA20_SDMMC, node_list, MAX_HOSTS);
+ debug("%s: count of sdhci nodes is %d\n", __func__, count);
+
+ if (process_nodes(blob, node_list, count)) {
+ printf("%s: Error processing mmc node(s)!\n", __func__);
+ return;
+ }
+}
COMPAT_NVIDIA_TEGRA20_NAND, /* Tegra2 NAND controller */
COMPAT_NVIDIA_TEGRA20_PWM, /* Tegra 2 PWM controller */
COMPAT_NVIDIA_TEGRA20_DC, /* Tegra 2 Display controller */
+ COMPAT_NVIDIA_TEGRA20_SDMMC, /* Tegra SDMMC controller */
COMPAT_NVIDIA_TEGRA20_SFLASH, /* Tegra 2 SPI flash controller */
COMPAT_NVIDIA_TEGRA20_SLINK, /* Tegra 2 SPI SLINK controller */
COMPAT_SMSC_LAN9215, /* SMSC 10/100 Ethernet LAN9215 */
COMPAT(NVIDIA_TEGRA20_NAND, "nvidia,tegra20-nand"),
COMPAT(NVIDIA_TEGRA20_PWM, "nvidia,tegra20-pwm"),
COMPAT(NVIDIA_TEGRA20_DC, "nvidia,tegra20-dc"),
+ COMPAT(NVIDIA_TEGRA20_SDMMC, "nvidia,tegra20-sdhci"),
COMPAT(NVIDIA_TEGRA20_SFLASH, "nvidia,tegra20-sflash"),
COMPAT(NVIDIA_TEGRA20_SLINK, "nvidia,tegra20-slink"),
COMPAT(SMSC_LAN9215, "smsc,lan9215"),
projects / u-boot / commitdiff