]> git.sur5r.net Git - u-boot/commitdiff
sunxi: Add defconfig and dts file for Polaroid MID2407PXE03 tablet
authorHans de Goede <hdegoede@redhat.com>
Sat, 11 Jun 2016 13:19:38 +0000 (15:19 +0200)
committerHans de Goede <hdegoede@redhat.com>
Mon, 20 Jun 2016 20:43:59 +0000 (22:43 +0200)
The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0
PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680
touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg
connector which doubles as charging port.

The dts file is identical to the one submitted to the upstream kernel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
arch/arm/dts/Makefile
arch/arm/dts/axp22x.dtsi
arch/arm/dts/sun8i-a23-polaroid-mid2407pxe03.dts [new file with mode: 0644]
board/sunxi/MAINTAINERS
configs/polaroid_mid2407pxe03_defconfig [new file with mode: 0644]

index 0a41eb2c938373c1cd5b3ee4dcc755b02d96404c..5172a7e2b92f3d9bb4843d2372d7dc7c909aa66b 100644 (file)
@@ -223,6 +223,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
 dtb-$(CONFIG_MACH_SUN8I_A23) += \
        sun8i-a23-evb.dtb \
        sun8i-a23-gt90h-v4.dtb \
+       sun8i-a23-polaroid-mid2407pxe03.dtb \
        sun8i-a23-polaroid-mid2809pxe04.dtb \
        sun8i-a23-q8-tablet.dtb
 dtb-$(CONFIG_MACH_SUN8I_A33) += \
index 0cfec509963701aa4f49f62db89df681b49077ea..458b6681e3ec54b37845b6245464e5385454c087 100644 (file)
                        regulator-max-microvolt = <3000000>;
                        regulator-name = "rtc_ldo";
                };
+
+               reg_drivevbus: drivevbus {
+                       regulator-name = "drivevbus";
+                       status = "disabled";
+               };
+       };
+
+       usb_power_supply: usb_power_supply {
+               compatible = "x-powers,axp221-usb-power-supply";
+               status = "disabled";
        };
 };
diff --git a/arch/arm/dts/sun8i-a23-polaroid-mid2407pxe03.dts b/arch/arm/dts/sun8i-a23-polaroid-mid2407pxe03.dts
new file mode 100644 (file)
index 0000000..bb2f073
--- /dev/null
@@ -0,0 +1,292 @@
+/*
+ * Copyright 2016 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a23.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+       model = "Polaroid MID2407PXE03 tablet";
+       compatible = "polaroid,mid2407pxe03", "allwinner,sun8i-a23";
+
+       aliases {
+               serial0 = &r_uart;
+       };
+
+       backlight: backlight {
+               compatible = "pwm-backlight";
+               pinctrl-names = "default";
+               pinctrl-0 = <&bl_en_pin_mid2407>;
+               pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+               brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+               default-brightness-level = <8>;
+               enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+       };
+
+       chosen {
+               stdout-path = "serial0:115200n8";
+       };
+};
+
+&i2c0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&i2c0_pins_a>;
+       status = "okay";
+       /*
+        * The gsl1680 is rated at 400KHz and it will not work reliable at
+        * 100KHz, this has been confirmed on multiple different tablets.
+        * The gsl1680 is the only device on this bus.
+        */
+       clock-frequency = <400000>;
+
+       gsl1680: touchscreen@40 {
+               compatible = "silead,gsl1680";
+               reg = <0x40>;
+               interrupt-parent = <&pio>;
+               interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>; /* PB5 */
+               pinctrl-names = "default";
+               pinctrl-0 = <&ts_power_pin_mid2407>;
+               power-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+               touchscreen-size-x = <960>;
+               touchscreen-size-y = <640>;
+               touchscreen-inverted-x;
+               touchscreen-inverted-y;
+               touchscreen-max-fingers = <5>;
+               touchscreen-fw-name = "silead/gsl1680-polaroid-mid2407pxe03.fw";
+       };
+};
+
+&i2c1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&i2c1_pins_a>;
+       status = "okay";
+};
+
+&lradc {
+       vref-supply = <&reg_vcc3v0>;
+       status = "okay";
+
+       button@200 {
+               label = "Volume Up";
+               linux,code = <KEY_VOLUMEUP>;
+               channel = <0>;
+               voltage = <200000>;
+       };
+
+       button@400 {
+               label = "Volume Down";
+               linux,code = <KEY_VOLUMEDOWN>;
+               channel = <0>;
+               voltage = <400000>;
+       };
+};
+
+&mmc0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_mid2407>;
+       vmmc-supply = <&reg_dcdc1>;
+       bus-width = <4>;
+       cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
+       cd-inverted;
+       status = "okay";
+};
+
+&pio {
+       bl_en_pin_mid2407: bl_en_pin@0 {
+               allwinner,pins = "PH6";
+               allwinner,function = "gpio_in";
+               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+       };
+
+       mmc0_cd_pin_mid2407: mmc0_cd_pin@0 {
+               allwinner,pins = "PB4";
+               allwinner,function = "gpio_in";
+               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+               allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+       };
+
+       ts_power_pin_mid2407: ts_power_pin@0 {
+               allwinner,pins = "PH1";
+               allwinner,function = "gpio_out";
+               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+       };
+
+       usb0_id_detect_pin: usb0_id_detect_pin@0 {
+               allwinner,pins = "PH8";
+               allwinner,function = "gpio_in";
+               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+               allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+       };
+};
+
+&pwm {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pwm0_pins>;
+       status = "okay";
+};
+
+&r_rsb {
+       status = "okay";
+
+       axp22x: pmic@3a3 {
+               compatible = "x-powers,axp223";
+               reg = <0x3a3>;
+               interrupt-parent = <&nmi_intc>;
+               interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+               eldoin-supply = <&reg_dcdc1>;
+               x-powers,drive-vbus-en;
+       };
+};
+
+&r_uart {
+       pinctrl-names = "default";
+       pinctrl-0 = <&r_uart_pins_a>;
+       status = "okay";
+};
+
+#include "axp22x.dtsi"
+
+&reg_aldo1 {
+       regulator-always-on;
+       regulator-min-microvolt = <3000000>;
+       regulator-max-microvolt = <3000000>;
+       regulator-name = "vcc-io";
+};
+
+&reg_aldo2 {
+       regulator-always-on;
+       regulator-min-microvolt = <2350000>;
+       regulator-max-microvolt = <2650000>;
+       regulator-name = "vdd-dll";
+};
+
+&reg_aldo3 {
+       regulator-always-on;
+       regulator-min-microvolt = <2700000>;
+       regulator-max-microvolt = <3300000>;
+       regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dc1sw {
+       regulator-name = "vcc-lcd";
+};
+
+&reg_dc5ldo {
+       regulator-always-on;
+       regulator-min-microvolt = <900000>;
+       regulator-max-microvolt = <1400000>;
+       regulator-name = "vdd-cpus";
+};
+
+&reg_dcdc1 {
+       regulator-always-on;
+       regulator-min-microvolt = <3000000>;
+       regulator-max-microvolt = <3000000>;
+       regulator-name = "vcc-3v0";
+};
+
+&reg_dcdc2 {
+       regulator-always-on;
+       regulator-min-microvolt = <900000>;
+       regulator-max-microvolt = <1400000>;
+       regulator-name = "vdd-sys";
+};
+
+&reg_dcdc3 {
+       regulator-always-on;
+       regulator-min-microvolt = <900000>;
+       regulator-max-microvolt = <1400000>;
+       regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc5 {
+       regulator-always-on;
+       regulator-min-microvolt = <1500000>;
+       regulator-max-microvolt = <1500000>;
+       regulator-name = "vcc-dram";
+};
+
+&reg_drivevbus {
+       regulator-name = "usb0-vbus";
+       status = "okay";
+};
+
+&reg_ldo_io1 {
+       regulator-always-on;
+       regulator-min-microvolt = <3300000>;
+       regulator-max-microvolt = <3300000>;
+       regulator-name = "vcc-touchscreen";
+       status = "okay";
+};
+
+&reg_rtc_ldo {
+       regulator-name = "vcc-rtc";
+};
+
+&simplefb_lcd {
+       vcc-lcd-supply = <&reg_dc1sw>;
+};
+
+&usb_otg {
+       dr_mode = "otg";
+       status = "okay";
+};
+
+&usb_power_supply {
+       status = "okay";
+};
+
+&usbphy {
+       pinctrl-names = "default";
+       pinctrl-0 = <&usb0_id_detect_pin>;
+       usb0_id_det-gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+       usb0_vbus_power-supply = <&usb_power_supply>;
+       usb0_vbus-supply = <&reg_drivevbus>;
+       status = "okay";
+};
index 2cb8a75dd8267b69165018f8de63c36392ec4c37..4f8d950c47816a1a65ff4bc65dfdf5d15e49844f 100644 (file)
@@ -58,6 +58,7 @@ F:    configs/orangepi_2_defconfig
 F:     configs/orangepi_one_defconfig
 F:     configs/orangepi_pc_defconfig
 F:     configs/orangepi_plus_defconfig
+F:     configs/polaroid_mid2407pxe03_defconfig
 F:     configs/polaroid_mid2809pxe04_defconfig
 F:     configs/q8_a23_tablet_800x480_defconfig
 F:     configs/q8_a33_tablet_800x480_defconfig
diff --git a/configs/polaroid_mid2407pxe03_defconfig b/configs/polaroid_mid2407pxe03_defconfig
new file mode 100644 (file)
index 0000000..9bf6fbf
--- /dev/null
@@ -0,0 +1,24 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN8I_A23=y
+CONFIG_DRAM_CLK=432
+CONFIG_DRAM_ZQ=63351
+CONFIG_MMC0_CD_PIN="PB4"
+CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
+CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_USB0_ID_DET="PH8"
+CONFIG_AXP_GPIO=y
+CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:40,up:31,lo:13,hs:1,vs:1,sync:3,vmode:0"
+CONFIG_VIDEO_LCD_DCLK_PHASE=0
+CONFIG_VIDEO_LCD_POWER="PH7"
+CONFIG_VIDEO_LCD_BL_EN="PH6"
+CONFIG_VIDEO_LCD_BL_PWM="PH0"
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-a23-polaroid-mid2407pxe03"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=5"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_AXP_DLDO1_VOLT=3300
+CONFIG_USB_MUSB_HOST=y