--- /dev/null
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+
+struct board_specific_parameters {
+ u32 datarate_mhz_low;
+ u32 datarate_mhz_high;
+ u32 n_ranks;
+ u32 clk_adjust;
+ u32 cpo;
+ u32 write_data_delay;
+ u32 force_2T;
+};
+
+const struct board_specific_parameters board_specific_parameters_udimm[][20] = {
+ {
+ /*
+ * memory controller 0
+ * lo| hi| num| clk| cpo|wrdata|2T
+ * mhz| mhz|ranks|adjst| | delay|
+ */
+ { 0, 300, 2, 4, 4, 2, 0},
+ {301, 365, 2, 4, 6, 2, 0},
+ {366, 450, 2, 4, 7, 2, 0},
+ {451, 850, 2, 4, 31, 2, 0},
+ { 0, 300, 1, 4, 4, 2, 0},
+ {301, 365, 1, 4, 6, 2, 0},
+ {366, 450, 1, 4, 7, 2, 0},
+ {451, 850, 1, 4, 31, 2, 0}
+ }
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ const struct board_specific_parameters *pbsp;
+ u32 num_params;
+ u32 i, dimm_num;
+ ulong ddr_freq;
+
+ if (ctrl_num != 0) /* we have only one controller */
+ return;
+ for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+ if (pdimm[i].n_ranks)
+ break;
+ }
+ if (i >= CONFIG_DIMM_SLOTS_PER_CTLR) /* no DIMM */
+ return;
+
+ dimm_num = i;
+ pbsp = &(board_specific_parameters_udimm[ctrl_num][0]);
+ num_params = sizeof(board_specific_parameters_udimm[ctrl_num]) /
+ sizeof(board_specific_parameters_udimm[0][0]);
+
+ /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+ * freqency and n_banks specified in board_specific_parameters table.
+ */
+ ddr_freq = get_ddr_freq(0) / 1000000;
+ for (i = 0; i < num_params; i++) {
+ if (ddr_freq >= pbsp->datarate_mhz_low &&
+ ddr_freq <= pbsp->datarate_mhz_high &&
+ pdimm[dimm_num].n_ranks == pbsp->n_ranks) {
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->cpo_override = pbsp->cpo;
+ popts->write_data_delay = pbsp->write_data_delay;
+ popts->twoT_en = pbsp->force_2T;
+ break;
+ }
+ pbsp++;
+ }
+
+ if (i == num_params) {
+ printf("Warning: board specific timing not found "
+ "for data rate %lu MT/s!\n", ddr_freq);
+ }
+
+ /*
+ * Factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+ popts->half_strength_driver_enable = 0;
+ popts->DQS_config = 0; /* only true DQS signal is used on board */
+}
#include <i2c.h>
#include <spi.h>
#include <miiphy.h>
+#ifdef CONFIG_FSL_DDR2
+#include <asm/fsl_ddr_sdram.h>
+#else
#include <spd_sdram.h>
+#endif
#if defined(CONFIG_OF_LIBFDT)
#include <libfdt.h>
phys_size_t initdram (int board_type)
{
volatile immap_t *im = (immap_t *)CONFIG_SYS_IMMR;
- u32 msize = 0;
+ phys_size_t msize = 0;
if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im)
return -1;
/* DDR SDRAM - Main SODIMM */
im->sysconf.ddrlaw[0].bar = CONFIG_SYS_DDR_BASE & LAWBAR_BAR;
#if defined(CONFIG_SPD_EEPROM)
- msize = spd_sdram();
+#ifndef CONFIG_FSL_DDR2
+ msize = spd_sdram() * 1024 * 1024;
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+ ddr_enable_ecc(msize);
+#endif
+#else
+ msize = fsl_ddr_sdram();
+#endif
#else
- msize = fixed_sdram();
+ msize = fixed_sdram() * 1024 * 1024;
#endif
/*
* Initialize SDRAM if it is on local bus.
*/
sdram_init();
-#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
- /*
- * Initialize and enable DDR ECC.
- */
- ddr_enable_ecc(msize * 1024 * 1024);
-#endif
-
/* return total bus SDRAM size(bytes) -- DDR */
- return (msize * 1024 * 1024);
+ return msize;
}
#if !defined(CONFIG_SPD_EEPROM)
projects / u-boot / commitdiff