+/*
+ * (C) Copyright 2000-2002
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
#ifndef _ASM_IO_H
#define _ASM_IO_H
#define setbits_8(addr, set) setbits(8, addr, set)
#define clrsetbits_8(addr, clear, set) clrsetbits(8, addr, clear, set)
-/*
- * ISA space is 'always mapped' on a typical x86 system, no need to
- * explicitly ioremap() it. The fact that the ISA IO space is mapped
- * to PAGE_OFFSET is pure coincidence - it does not mean ISA values
- * are physical addresses. The following constant pointer can be
- * used as the IO-area pointer (it can be iounmapped as well, so the
- * analogy with PCI is quite large):
- */
-#define isa_readb(a) readb((a))
-#define isa_readw(a) readw((a))
-#define isa_readl(a) readl((a))
-#define isa_writeb(b,a) writeb(b,(a))
-#define isa_writew(w,a) writew(w,(a))
-#define isa_writel(l,a) writel(l,(a))
-#define isa_memset_io(a,b,c) memset_io((a),(b),(c))
-#define isa_memcpy_fromio(a,b,c) memcpy_fromio((a),(b),(c))
-#define isa_memcpy_toio(a,b,c) memcpy_toio((a),(b),(c))
-
-
-static inline int check_signature(unsigned long io_addr,
- const unsigned char *signature, int length)
-{
- int retval = 0;
- do {
- if (readb(io_addr) != *signature)
- goto out;
- io_addr++;
- signature++;
- length--;
- } while (length);
- retval = 1;
-out:
- return retval;
-}
-
-/**
- * isa_check_signature - find BIOS signatures
- * @io_addr: mmio address to check
- * @signature: signature block
- * @length: length of signature
- *
- * Perform a signature comparison with the ISA mmio address io_addr.
- * Returns 1 on a match.
- *
- * This function is deprecated. New drivers should use ioremap and
- * check_signature.
- */
-
-
-static inline int isa_check_signature(unsigned long io_addr,
- const unsigned char *signature, int length)
-{
- int retval = 0;
- do {
- if (isa_readb(io_addr) != *signature)
- goto out;
- io_addr++;
- signature++;
- length--;
- } while (length);
- retval = 1;
-out:
- return retval;
-}
-
#endif /* __KERNEL__ */
#ifdef SLOW_IO_BY_JUMPING
#define __iormb() dmb()
#define __iowmb() dmb()
-#endif
+#endif /* _ASM_IO_H */
#include <asm/acpi_s3.h>
#include <asm/acpi_table.h>
#include <asm/post.h>
+#include <linux/linkage.h>
DECLARE_GLOBAL_DATA_PTR;
Note that PCIE_ECAM_BASE is set up by the FSP so the value used
by U-Boot matches that value.
+config TARGET_THEADORABLE_X86_CONGA_QA3_E3845
+ bool "theadorable-x86 baseboard & conga-QA3/E3845"
+ help
+ This is the theadorable-x86 baseboard board equipped with the
+ conga-QA3/E3845-4G SoM. It contains an Atom E3845 with Ethernet,
+ micro-SD, USB 2, USB 3, SATA, serial console and HDMI 1.3 video
+ out. It requires some binary blobs - see README.x86 for details.
+
+ Note that PCIE_ECAM_BASE is set up by the FSP so the value used
+ by U-Boot matches that value.
+
endchoice
source "board/congatec/conga-qeval20-qa3-e3845/Kconfig"
-if TARGET_CONGA_QEVAL20_QA3_E3845
-
config SYS_BOARD
default "conga-qeval20-qa3-e3845"
default "baytrail"
config SYS_CONFIG_NAME
- default "conga-qeval20-qa3-e3845"
+ default "conga-qeval20-qa3-e3845" if TARGET_CONGA_QEVAL20_QA3_E3845
+ default "theadorable-x86-conga-qa3-e3845" if TARGET_THEADORABLE_X86_CONGA_QA3_E3845
config SYS_TEXT_BASE
default 0xfff00000 if !EFI_STUB
select BOARD_EARLY_INIT_F
select BOARD_LATE_INIT
select SPI_FLASH_STMICRO
+ imply SPI_FLASH_SPANSION
+ imply SPI_FLASH_WINBOND
config PCIE_ECAM_BASE
default 0xe0000000
-
-endif
S: Maintained
F: board/congatec/conga-qeval20-qa3-e3845
F: include/configs/conga-qeval20-qa3-e3845.h
+F: include/configs/theadorable-x86-conga-qa3-e3845.h
F: configs/conga-qeval20-qa3-e3845_defconfig
F: configs/conga-qeval20-qa3-e3845-internal-uart_defconfig
+F: configs/theadorable-x86-conga-qa3-e3845_defconfig
+F: configs/theadorable-x86-conga-qa3-e3845-pcie-x4_defconfig
F: arch/x86/dts/conga-qeval20-qa3-e3845.dts
choice
prompt "Mainboard model"
- optional
-config TARGET_DFI_BT700
- bool "DFI BT700 BayTrail"
+config TARGET_Q7X_151_DFI_BT700
+ bool "DFI BT700 BayTrail on DFI Q7X-151 baseboard"
imply SCSI
help
This is the DFI Q7X-151 baseboard equipped with the
Note that PCIE_ECAM_BASE is set up by the FSP so the value used
by U-Boot matches that value.
+config TARGET_THEADORABLE_X86_DFI_BT700
+ bool "DFI BT700 BayTrail on theadorable-x86 baseboard"
+ imply SCSI
+ help
+ This is the theadorable-x86 baseboard equipped with the
+ DFI BayTrail Bt700 SoM. It contains an Atom E3845 with
+ Ethernet (in non-PCIe-x4 configuration), micro-SD, USB 2,
+ USB 3, SATA, serial console and DisplayPort video out.
+ It requires some binary blobs - see README.x86 for details.
+
+ Note that PCIE_ECAM_BASE is set up by the FSP so the value used
+ by U-Boot matches that value.
+
endchoice
source "board/dfi/dfi-bt700/Kconfig"
-if TARGET_DFI_BT700
-
config SYS_BOARD
default "dfi-bt700"
default "baytrail"
config SYS_CONFIG_NAME
- default "dfi-bt700"
+ default "dfi-bt700" if TARGET_Q7X_151_DFI_BT700
+ default "theadorable-x86-dfi-bt700" if TARGET_THEADORABLE_X86_DFI_BT700
config SYS_TEXT_BASE
default 0xfff00000 if !EFI_STUB
select BOARD_EARLY_INIT_F
select BOARD_LATE_INIT
select SPI_FLASH_STMICRO
+ imply SPI_FLASH_SPANSION
+ imply SPI_FLASH_WINBOND
config PCIE_ECAM_BASE
default 0xe0000000
-
-endif
S: Maintained
F: board/dfi/dfi-bt700
F: include/configs/dfi-bt700.h
+F: include/configs/theadorable-x86-dfi-bt700.h
F: configs/dfi-bt700-q7x-151_defconfig
F: configs/theadorable-x86-dfi-bt700_defconfig
F: arch/x86/dts/dfi-bt700.dtsi
CONFIG_VENDOR_CONGATEC=y
CONFIG_TARGET_CONGA_QEVAL20_QA3_E3845=y
CONFIG_DEFAULT_DEVICE_TREE="conga-qeval20-qa3-e3845"
-CONFIG_DEBUG_UART=y
CONFIG_SMP=y
CONFIG_HAVE_VGA_BIOS=y
+CONFIG_VGA_BIOS_ADDR=0xfffa0000
CONFIG_GENERATE_PIRQ_TABLE=y
CONFIG_GENERATE_MP_TABLE=y
CONFIG_GENERATE_ACPI_TABLE=y
+CONFIG_HAVE_ACPI_RESUME=y
CONFIG_SEABIOS=y
CONFIG_FIT=y
CONFIG_FIT_SIGNATURE=y
CONFIG_SYS_I2C_INTEL=y
CONFIG_WINBOND_W83627=y
CONFIG_E1000=y
-CONFIG_DEBUG_UART_BASE=0x3f8
-CONFIG_DEBUG_UART_CLOCK=1843200
CONFIG_USB_STORAGE=y
CONFIG_USB_KEYBOARD=y
CONFIG_FRAMEBUFFER_SET_VESA_MODE=y
CONFIG_X86=y
CONFIG_VENDOR_DFI=y
CONFIG_DEFAULT_DEVICE_TREE="dfi-bt700-q7x-151"
-CONFIG_TARGET_DFI_BT700=y
-CONFIG_DEBUG_UART=y
CONFIG_SMP=y
CONFIG_HAVE_VGA_BIOS=y
+CONFIG_VGA_BIOS_ADDR=0xfffa0000
CONFIG_GENERATE_PIRQ_TABLE=y
CONFIG_GENERATE_MP_TABLE=y
CONFIG_GENERATE_ACPI_TABLE=y
+CONFIG_HAVE_ACPI_RESUME=y
CONFIG_SEABIOS=y
CONFIG_FIT=y
CONFIG_FIT_SIGNATURE=y
CONFIG_DM_I2C=y
CONFIG_NUVOTON_NCT6102D=y
CONFIG_E1000=y
-CONFIG_DEBUG_UART_BASE=0x3f8
-CONFIG_DEBUG_UART_CLOCK=1843200
CONFIG_USB_STORAGE=y
CONFIG_USB_KEYBOARD=y
CONFIG_FRAMEBUFFER_SET_VESA_MODE=y
--- /dev/null
+CONFIG_X86=y
+CONFIG_VENDOR_CONGATEC=y
+CONFIG_TARGET_THEADORABLE_X86_CONGA_QA3_E3845=y
+CONFIG_DEFAULT_DEVICE_TREE="conga-qeval20-qa3-e3845"
+CONFIG_INTERNAL_UART=y
+CONFIG_FLASH_DESCRIPTOR_FILE="descriptor-pcie-x4.bin"
+CONFIG_SMP=y
+CONFIG_HAVE_VGA_BIOS=y
+CONFIG_VGA_BIOS_ADDR=0xfffa0000
+CONFIG_GENERATE_PIRQ_TABLE=y
+CONFIG_GENERATE_MP_TABLE=y
+CONFIG_GENERATE_ACPI_TABLE=y
+CONFIG_HAVE_ACPI_RESUME=y
+CONFIG_SEABIOS=y
+CONFIG_FIT=y
+CONFIG_FIT_SIGNATURE=y
+CONFIG_BOOTSTAGE=y
+CONFIG_BOOTSTAGE_REPORT=y
+CONFIG_SYS_CONSOLE_INFO_QUIET=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_CPU=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_DHCP=y
+# CONFIG_CMD_NFS is not set
+CONFIG_CMD_PING=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_BOOTSTAGE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_ISO_PARTITION=y
+CONFIG_AMIGA_PARTITION=y
+CONFIG_EFI_PARTITION=y
+CONFIG_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_CPU=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_INTEL=y
+CONFIG_WINBOND_W83627=y
+CONFIG_E1000=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_KEYBOARD=y
+CONFIG_FRAMEBUFFER_SET_VESA_MODE=y
+CONFIG_FRAMEBUFFER_VESA_MODE_114=y
+CONFIG_CONSOLE_SCROLL_LINES=5
--- /dev/null
+CONFIG_X86=y
+CONFIG_VENDOR_CONGATEC=y
+CONFIG_TARGET_THEADORABLE_X86_CONGA_QA3_E3845=y
+CONFIG_DEFAULT_DEVICE_TREE="conga-qeval20-qa3-e3845"
+CONFIG_INTERNAL_UART=y
+CONFIG_SMP=y
+CONFIG_HAVE_VGA_BIOS=y
+CONFIG_VGA_BIOS_ADDR=0xfffa0000
+CONFIG_GENERATE_PIRQ_TABLE=y
+CONFIG_GENERATE_MP_TABLE=y
+CONFIG_GENERATE_ACPI_TABLE=y
+CONFIG_HAVE_ACPI_RESUME=y
+CONFIG_SEABIOS=y
+CONFIG_FIT=y
+CONFIG_FIT_SIGNATURE=y
+CONFIG_BOOTSTAGE=y
+CONFIG_BOOTSTAGE_REPORT=y
+CONFIG_SYS_CONSOLE_INFO_QUIET=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_CPU=y
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_GPIO=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_DHCP=y
+# CONFIG_CMD_NFS is not set
+CONFIG_CMD_PING=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_BOOTSTAGE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_MAC_PARTITION=y
+CONFIG_ISO_PARTITION=y
+CONFIG_EFI_PARTITION=y
+CONFIG_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_CPU=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_INTEL=y
+CONFIG_WINBOND_W83627=y
+CONFIG_E1000=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_KEYBOARD=y
+CONFIG_FRAMEBUFFER_SET_VESA_MODE=y
+CONFIG_FRAMEBUFFER_VESA_MODE_114=y
+CONFIG_CONSOLE_SCROLL_LINES=5
CONFIG_X86=y
CONFIG_VENDOR_DFI=y
CONFIG_DEFAULT_DEVICE_TREE="theadorable-x86-dfi-bt700"
-CONFIG_TARGET_DFI_BT700=y
+CONFIG_TARGET_THEADORABLE_X86_DFI_BT700=y
CONFIG_SMP=y
CONFIG_HAVE_VGA_BIOS=y
CONFIG_VGA_BIOS_ADDR=0xfffa0000
CONFIG_GENERATE_PIRQ_TABLE=y
CONFIG_GENERATE_MP_TABLE=y
CONFIG_GENERATE_ACPI_TABLE=y
+CONFIG_HAVE_ACPI_RESUME=y
CONFIG_SEABIOS=y
CONFIG_FIT=y
CONFIG_FIT_SIGNATURE=y
--- /dev/null
+/*
+ * Copyright (C) 2016 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * Common options, macros and default environment for all
+ * theadorable x86 based boards
+ */
+
+#ifndef __THEADORABLE_X86_COMMON_H
+#define __THEADORABLE_X86_COMMON_H
+
+#define CONFIG_SYS_MONITOR_LEN (1 << 20)
+
+#define CONFIG_PREBOOT
+
+#define CONFIG_STD_DEVICES_SETTINGS "stdin=serial\0" \
+ "stdout=serial\0" \
+ "stderr=serial\0"
+
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_USB_ETHER_SMSC95XX
+#define CONFIG_USB_ETHER_MCS7830
+#define CONFIG_USB_ETHER_RTL8152
+
+#define VIDEO_IO_OFFSET 0
+#define CONFIG_X86EMU_RAW_IO
+#define CONFIG_CMD_BMP
+#define CONFIG_BMP_16BPP
+
+/* Environment settings */
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#undef CONFIG_ENV_SIZE
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x1000
+#define CONFIG_ENV_OFFSET 0x006ec000
+#define CONFIG_ENV_OFFSET_REDUND \
+ (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+
+#undef CONFIG_BOOTARGS
+#undef CONFIG_BOOTCOMMAND
+#undef CONFIG_EXTRA_ENV_SETTINGS
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "tftpdir=" DEF_ENV_TFTPDIR "\0" \
+ "eth_init=" DEF_ENV_ETH_INIT "\0" \
+ "ubuntu_part=" __stringify(DEF_ENV_UBUNTU_PART) "\0" \
+ "yocto_part=" __stringify(DEF_ENV_YOCTO_PART) "\0" \
+ "ubuntu_tty=" __stringify(DEF_ENV_UBUNTU_TTY) "\0" \
+ "yocto_tty=" __stringify(DEF_ENV_YOCTO_TTY) "\0" \
+ "start_eth=if test -n \"${eth_init}\";" \
+ "then run eth_init;else sleep 0;fi\0" \
+ "kernel-ver=4.8.0-54\0" \
+ "boot=zboot 03000000 0 04000000 ${filesize}\0" \
+ "mtdparts=mtdparts=intel-spi:4k(descriptor),7084k(me)," \
+ "8k(env1),8k(env2),64k(mrc),640k(u-boot)," \
+ "64k(vga),-(fsp)\0" \
+ "addtty_ubuntu=setenv bootargs ${bootargs} " \
+ "console=ttyS${ubuntu_tty},${baudrate}\0" \
+ "addtty_yocto=setenv bootargs ${bootargs} " \
+ "console=ttyS${yocto_tty},${baudrate}\0" \
+ "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
+ "addmisc=setenv bootargs ${bootargs} " \
+ "intel-spi.writeable=1 vmalloc=300M " \
+ "pci=realloc=on,hpmemsize=0x12000000\0" \
+ "bootcmd=if env exists recovery_status;" \
+ "then run swupdate;" \
+ "else run yocto_boot;run swupdate;" \
+ "fi\0" \
+ "ubuntu_args=setenv bootargs " \
+ "root=/dev/sda${ubuntu_part} ro\0" \
+ "ubuntu_args_quiet=setenv bootargs " \
+ "root=/dev/sda${ubuntu_part} ro quiet\0" \
+ "ubuntu_load=load scsi 0:${ubuntu_part} 03000000 " \
+ "/boot/vmlinuz-${kernel-ver}-generic;" \
+ "load scsi 0:${ubuntu_part} 04000000 " \
+ "/boot/initrd.img-${kernel-ver}-generic\0" \
+ "ubuntu_boot=run ubuntu_args_quiet addmtd addmisc " \
+ "ubuntu_load boot\0" \
+ "ubuntu_boot_console=run ubuntu_args addtty_ubuntu " \
+ "addmtd addmisc ubuntu_load boot\0" \
+ "net_args=setenv bootargs root=/dev/sda${ubuntu_part} ro\0" \
+ "net_boot=run start_eth net_args addtty_yocto addmtd addmisc;" \
+ "tftp 03000000 ${tftpdir}/bzImage;" \
+ "load scsi 0:${ubuntu_part} 04000000 " \
+ "/boot/initrd.img-${kernel-ver}-generic;" \
+ "run boot\0" \
+ "yocto_args=setenv bootargs root=/dev/sda${yocto_part} " \
+ "ip=dhcp panic=1\0" \
+ "yocto_args_fast=setenv bootargs root=/dev/sda${yocto_part} " \
+ "quiet panic=1\0" \
+ "yocto_boot=run yocto_args addmtd addmisc addtty_yocto;" \
+ "if run yocto_load;then zboot 03000000;fi\0" \
+ "yocto_boot_fast=run yocto_args_fast addmtd addmisc " \
+ "addtty_yocto yocto_load;zboot 03000000\0" \
+ "yocto_boot_tftp=run yocto_args addmtd addmisc addtty_yocto " \
+ "start_eth yocto_load_tftp;zboot 03000000\0" \
+ "yocto_kernel=bzImage\0" \
+ "yocto_load=load scsi 0:${yocto_part} 03000000 " \
+ "/boot/${yocto_kernel}\0" \
+ "yocto_load_tftp=tftp 03000000 dfi/bzImage\0" \
+ "swupdate=if env exists swupdate_factory;" \
+ "then run swupdate_usb;run swupdate_run;" \
+ "else setenv swupdate_part 2;run swupdate_mmc;" \
+ "run swupdate_run;setenv swupdate_part 1;" \
+ "run swupdate_mmc;run swupdate_usb;" \
+ "run swupdate_run;" \
+ "fi\0" \
+ "swupdate-initrd=/boot/swupdate-image-theadorable.ext4.gz\0" \
+ "swupdate-kernel=/boot/bzImage\0" \
+ "swupdate_args=setenv bootargs root=/dev/ram rw ip=dhcp panic=1\0" \
+ "swupdate_dev=0\0" \
+ "swupdate_factory=0\0" \
+ "swupdate_interface=usb\0" \
+ "swupdate_kernel=vmlinuz-4.4.0-28-generic\0" \
+ "swupdate_load=load ${swupdate_interface} ${swupdate_dev}:" \
+ "${swupdate_part} 03000000 ${swupdate-kernel}" \
+ " && load ${swupdate_interface} ${swupdate_dev}:" \
+ "${swupdate_part} 04000000 ${swupdate-initrd}\0" \
+ "swupdate_mmc=setenv swupdate_interface mmc;" \
+ "setenv swupdate_dev ${swupdate_mmcdev};" \
+ "setenv swupdate_part 1;" \
+ "mmc dev ${swupdate_dev};mmc rescan\0" \
+ "swupdate_mmcdev=0\0" \
+ "swupdate_part=1\0" \
+ "swupdate_run=run swupdate_args addtty_yocto addmtd addmisc;" \
+ "if run swupdate_load;then run boot;" \
+ "else echo SWUpdate cannot be started from " \
+ "${swupdate_interface};" \
+ "fi\0" \
+ "swupdate_usb=setenv swupdate_interface usb;" \
+ "setenv swupdate_dev 0;setenv swupdate_part 1;" \
+ "usb start\0" \
+ "logo_tftp=tftp ${loadaddr} ${tftpdir}/logo.bmp;" \
+ "bmp display ${loadaddr}\0" \
+ "preboot=scsi scan;load scsi 0:${ubuntu_part} ${loadaddr} " \
+ "/boot/logo/logo.bmp;bmp display ${loadaddr}\0" \
+ "rootpath=/tftpboot/theadorable-x86-conga/work/" \
+ "rootfs-yocto-swupdate-2017-03-29\0" \
+ "addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:" \
+ "${gatewayip}:${netmask}:${hostname}:eth0:off\0" \
+ "set_bootargs_nfs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath},tcp,nfsvers=3\0" \
+ "net_nfs=run start_eth set_bootargs_nfs addtty_yocto addip " \
+ "addmtd addmisc;tftp 03000000 ${tftpdir}/bzImage;" \
+ "zboot 03000000\0" \
+ "load_uboot=tftp ${loadaddr} ${tftpdir}/u-boot.rom\0" \
+ "update_uboot=sf probe;" \
+ "sf update ${loadaddr} 0 800000;saveenv\0" \
+ "upd_uboot=run start_eth load_uboot update_uboot\0"
+
+#endif /* __THEADORABLE_X86_COMMON_H */
--- /dev/null
+/*
+ * Copyright (C) 2016 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <configs/x86-common.h>
+
+/* Set the board specific parameters */
+#define DEF_ENV_TFTPDIR "theadorable-x86-conga"
+#define DEF_ENV_ETH_INIT ""
+#define DEF_ENV_UBUNTU_PART 2
+#define DEF_ENV_UBUNTU_TTY 0 /* Use ttyS0 */
+#define DEF_ENV_YOCTO_PART 3
+#define DEF_ENV_YOCTO_TTY 0 /* Use ttyS0 */
+
+/*
+ * Include the theadorable-x86 common options, macros and default
+ * environment
+ */
+#include <configs/theadorable-x86-common.h>
+
+#endif /* __CONFIG_H */
--- /dev/null
+/*
+ * Copyright (C) 2016 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <configs/x86-common.h>
+
+/* Use BayTrail internal HS UART which is memory-mapped */
+#undef CONFIG_SYS_NS16550_PORT_MAPPED
+
+/* Set the board specific parameters */
+#define DEF_ENV_TFTPDIR "theadorable-x86-dfi"
+#define DEF_ENV_ETH_INIT "usb reset"
+#define DEF_ENV_UBUNTU_PART 1
+#define DEF_ENV_UBUNTU_TTY 4 /* Use ttyS4 */
+#define DEF_ENV_YOCTO_PART 2
+#define DEF_ENV_YOCTO_TTY 1 /* Use ttyS1 */
+
+/*
+ * Include the theadorable-x86 common options, macros and default
+ * environment
+ */
+#include <configs/theadorable-x86-common.h>
+
+#endif /* __CONFIG_H */
projects / u-boot / commitdiff