--------------------------------------
- 12/15/2003 Initial port to u-boot by Sascha Hauer <saschahauer@web.de>
+ 12/15/2003 Initial port to u-boot by
+ Sascha Hauer <saschahauer@web.de>
+
+ 06/03/2008 Remy Bohmer <linux@bohmer.net>
+ - Fixed the driver to work with DM9000A.
+ (check on ISR receive status bit before reading the
+ FIFO as described in DM9000 programming guide and
+ application notes)
+ - Added autodetect of databus width.
+ - Made debug code compile again.
+ - Adapt eth_send such that it matches the DM9000*
+ application notes. Needed to make it work properly
+ for DM9000A.
+ - Adapted reset procedure to match DM9000 application
+ notes (i.e. double reset)
+ - some minor code cleanups
+ These changes are tested with DM9000{A,EP,E} together
+ with a 200MHz Atmel AT91SAM92161 core
TODO: Homerun NIC and longrun NIC are not functional, only internal at the
moment.
/* #define CONFIG_DM9000_DEBUG */
#ifdef CONFIG_DM9000_DEBUG
-#define DM9000_DBG(fmt,args...) printf(fmt ,##args)
-#else /* */
+#define DM9000_DBG(fmt,args...) printf(fmt, ##args)
+#define DM9000_DMP_PACKET(func,packet,length) \
+ do { \
+ int i; \
+ printf(func ": length: %d\n", length); \
+ for (i = 0; i < length; i++) { \
+ if (i % 8 == 0) \
+ printf("\n%s: %02x: ", func, i); \
+ printf("%02x ", ((unsigned char *) packet)[i]); \
+ } printf("\n"); \
+ } while(0)
+#else
#define DM9000_DBG(fmt,args...)
-#endif /* */
+#define DM9000_DMP_PACKET(func,packet,length)
+#endif
+
enum DM9000_PHY_mode { DM9000_10MHD = 0, DM9000_100MHD =
1, DM9000_10MFD = 4, DM9000_100MFD = 5, DM9000_AUTO =
8, DM9000_1M_HPNA = 0x10
u8 device_wait_reset; /* device state */
u8 nic_type; /* NIC type */
unsigned char srom[128];
+ void (*outblk)(volatile void *data_ptr, int count);
+ void (*inblk)(void *data_ptr, int count);
+ void (*rx_status)(u16 *RxStatus, u16 *RxLen);
} board_info_t;
-board_info_t dmfe_info;
+static board_info_t dm9000_info;
/* For module input parameter */
static int media_mode = DM9000_AUTO;
DM9000_DBG("TSRII (0x04): %02x\n", DM9000_ior(4));
DM9000_DBG("RCR (0x05): %02x\n", DM9000_ior(5));
DM9000_DBG("RSR (0x06): %02x\n", DM9000_ior(6));
- DM9000_DBG("ISR (0xFE): %02x\n", DM9000_ior(ISR));
+ DM9000_DBG("ISR (0xFE): %02x\n", DM9000_ior(DM9000_ISR));
DM9000_DBG("\n");
}
-#endif /* */
+#endif
+
+static void dm9000_outblk_8bit(volatile void *data_ptr, int count)
+{
+ int i;
+ for (i = 0; i < count; i++)
+ DM9000_outb((((u8 *) data_ptr)[i] & 0xff), DM9000_DATA);
+}
+
+static void dm9000_outblk_16bit(volatile void *data_ptr, int count)
+{
+ int i;
+ u32 tmplen = (count + 1) / 2;
+
+ for (i = 0; i < tmplen; i++)
+ DM9000_outw(((u16 *) data_ptr)[i], DM9000_DATA);
+}
+static void dm9000_outblk_32bit(volatile void *data_ptr, int count)
+{
+ int i;
+ u32 tmplen = (count + 3) / 4;
+
+ for (i = 0; i < tmplen; i++)
+ DM9000_outl(((u32 *) data_ptr)[i], DM9000_DATA);
+}
+
+static void dm9000_inblk_8bit(void *data_ptr, int count)
+{
+ int i;
+ for (i = 0; i < count; i++)
+ ((u8 *) data_ptr)[i] = DM9000_inb(DM9000_DATA);
+}
+
+static void dm9000_inblk_16bit(void *data_ptr, int count)
+{
+ int i;
+ u32 tmplen = (count + 1) / 2;
+
+ for (i = 0; i < tmplen; i++)
+ ((u16 *) data_ptr)[i] = DM9000_inw(DM9000_DATA);
+}
+static void dm9000_inblk_32bit(void *data_ptr, int count)
+{
+ int i;
+ u32 tmplen = (count + 3) / 4;
+
+ for (i = 0; i < tmplen; i++)
+ ((u32 *) data_ptr)[i] = DM9000_inl(DM9000_DATA);
+}
+
+static void dm9000_rx_status_32bit(u16 *RxStatus, u16 *RxLen)
+{
+ u32 tmpdata;
+
+ DM9000_outb(DM9000_MRCMD, DM9000_IO);
+
+ tmpdata = DM9000_inl(DM9000_DATA);
+ *RxStatus = tmpdata;
+ *RxLen = tmpdata >> 16;
+}
+
+static void dm9000_rx_status_16bit(u16 *RxStatus, u16 *RxLen)
+{
+ DM9000_outb(DM9000_MRCMD, DM9000_IO);
+
+ *RxStatus = DM9000_inw(DM9000_DATA);
+ *RxLen = DM9000_inw(DM9000_DATA);
+}
+
+static void dm9000_rx_status_8bit(u16 *RxStatus, u16 *RxLen)
+{
+ DM9000_outb(DM9000_MRCMD, DM9000_IO);
+
+ *RxStatus = DM9000_inb(DM9000_DATA) + (DM9000_inb(DM9000_DATA) << 8);
+ *RxLen = DM9000_inb(DM9000_DATA) + (DM9000_inb(DM9000_DATA) << 8);
+}
/*
Search DM9000 board, allocate space and register it
static void
identify_nic(void)
{
- struct board_info *db = &dmfe_info; /* Point a board information structure */
+ struct board_info *db = &dm9000_info;
u16 phy_reg3;
DM9000_iow(DM9000_NCR, NCR_EXT_PHY);
phy_reg3 = phy_read(3);
static void
dm9000_reset(void)
{
- DM9000_DBG("resetting\n");
- DM9000_iow(DM9000_NCR, NCR_RST);
- udelay(1000); /* delay 1ms */
+ DM9000_DBG("resetting DM9000\n");
+
+ /* Reset DM9000,
+ see DM9000 Application Notes V1.22 Jun 11, 2004 page 29 */
+
+ /* DEBUG: Make all GPIO pins outputs */
+ DM9000_iow(DM9000_GPCR, 0x0F);
+ /* Step 1: Power internal PHY by writing 0 to GPIO0 pin */
+ DM9000_iow(DM9000_GPR, 0);
+ /* Step 2: Software reset */
+ DM9000_iow(DM9000_NCR, 3);
+
+ do {
+ DM9000_DBG("resetting the DM9000, 1st reset\n");
+ udelay(25); /* Wait at least 20 us */
+ } while (DM9000_ior(DM9000_NCR) & 1);
+
+ DM9000_iow(DM9000_NCR, 0);
+ DM9000_iow(DM9000_NCR, 3); /* Issue a second reset */
+
+ do {
+ DM9000_DBG("resetting the DM9000, 2nd reset\n");
+ udelay(25); /* Wait at least 20 us */
+ } while (DM9000_ior(DM9000_NCR) & 1);
+
+ /* Check whether the ethernet controller is present */
+ if ((DM9000_ior(DM9000_PIDL) != 0x0) ||
+ (DM9000_ior(DM9000_PIDH) != 0x90))
+ printf("ERROR: resetting DM9000 -> not responding\n");
}
/* Initilize dm9000 board
eth_init(bd_t * bd)
{
int i, oft, lnk;
+ u8 io_mode;
+ struct board_info *db = &dm9000_info;
+
DM9000_DBG("eth_init()\n");
/* RESET device */
dm9000_reset();
dm9000_probe();
+ /* Auto-detect 8/16/32 bit mode, ISR Bit 6+7 indicate bus width */
+ io_mode = DM9000_ior(DM9000_ISR) >> 6;
+
+ switch (io_mode) {
+ case 0x0: /* 16-bit mode */
+ printf("DM9000: running in 16 bit mode\n");
+ db->outblk = dm9000_outblk_16bit;
+ db->inblk = dm9000_inblk_16bit;
+ db->rx_status = dm9000_rx_status_16bit;
+ break;
+ case 0x01: /* 32-bit mode */
+ printf("DM9000: running in 32 bit mode\n");
+ db->outblk = dm9000_outblk_32bit;
+ db->inblk = dm9000_inblk_32bit;
+ db->rx_status = dm9000_rx_status_32bit;
+ break;
+ case 0x02: /* 8 bit mode */
+ printf("DM9000: running in 8 bit mode\n");
+ db->outblk = dm9000_outblk_8bit;
+ db->inblk = dm9000_inblk_8bit;
+ db->rx_status = dm9000_rx_status_8bit;
+ break;
+ default:
+ /* Assume 8 bit mode, will probably not work anyway */
+ printf("DM9000: Undefined IO-mode:0x%x\n", io_mode);
+ db->outblk = dm9000_outblk_8bit;
+ db->inblk = dm9000_inblk_8bit;
+ db->rx_status = dm9000_rx_status_8bit;
+ break;
+ }
+
/* NIC Type: FASTETHER, HOMERUN, LONGRUN */
identify_nic();
/* Set PHY */
set_PHY_mode();
- /* Program operating register */
- DM9000_iow(DM9000_NCR, 0x0); /* only intern phy supported by now */
- DM9000_iow(DM9000_TCR, 0); /* TX Polling clear */
- DM9000_iow(DM9000_BPTR, 0x3f); /* Less 3Kb, 200us */
- DM9000_iow(DM9000_FCTR, FCTR_HWOT(3) | FCTR_LWOT(8)); /* Flow Control : High/Low Water */
- DM9000_iow(DM9000_FCR, 0x0); /* SH FIXME: This looks strange! Flow Control */
- DM9000_iow(DM9000_SMCR, 0); /* Special Mode */
- DM9000_iow(DM9000_NSR, NSR_WAKEST | NSR_TX2END | NSR_TX1END); /* clear TX status */
- DM9000_iow(DM9000_ISR, 0x0f); /* Clear interrupt status */
+ /* Program operating register, only intern phy supported by now */
+ DM9000_iow(DM9000_NCR, 0x0);
+ /* TX Polling clear */
+ DM9000_iow(DM9000_TCR, 0);
+ /* Less 3Kb, 200us */
+ DM9000_iow(DM9000_BPTR, 0x3f);
+ /* Flow Control : High/Low Water */
+ DM9000_iow(DM9000_FCTR, FCTR_HWOT(3) | FCTR_LWOT(8));
+ /* SH FIXME: This looks strange! Flow Control */
+ DM9000_iow(DM9000_FCR, 0x0);
+ /* Special Mode */
+ DM9000_iow(DM9000_SMCR, 0);
+ /* clear TX status */
+ DM9000_iow(DM9000_NSR, NSR_WAKEST | NSR_TX2END | NSR_TX1END);
+ /* Clear interrupt status */
+ DM9000_iow(DM9000_ISR, 0x0f);
/* Set Node address */
+ #ifndef CONFIG_AT91SAM9261EK
for (i = 0; i < 6; i++)
((u16 *) bd->bi_enetaddr)[i] = read_srom_word(i);
+ #endif
if (is_zero_ether_addr(bd->bi_enetaddr) ||
is_multicast_ether_addr(bd->bi_enetaddr)) {
DM9000_DBG("\n");
/* Activate DM9000 */
- DM9000_iow(DM9000_RCR, RCR_DIS_LONG | RCR_DIS_CRC | RCR_RXEN); /* RX enable */
- DM9000_iow(DM9000_IMR, IMR_PAR); /* Enable TX/RX interrupt mask */
+ /* RX enable */
+ DM9000_iow(DM9000_RCR, RCR_DIS_LONG | RCR_DIS_CRC | RCR_RXEN);
+ /* Enable TX/RX interrupt mask */
+ DM9000_iow(DM9000_IMR, IMR_PAR);
+
i = 0;
while (!(phy_read(1) & 0x20)) { /* autonegation complete bit */
udelay(1000);
int
eth_send(volatile void *packet, int length)
{
- char *data_ptr;
- u32 tmplen, i;
int tmo;
- DM9000_DBG("eth_send: length: %d\n", length);
- for (i = 0; i < length; i++) {
- if (i % 8 == 0)
- DM9000_DBG("\nSend: 02x: ", i);
- DM9000_DBG("%02x ", ((unsigned char *) packet)[i]);
- } DM9000_DBG("\n");
+ struct board_info *db = &dm9000_info;
- /* Move data to DM9000 TX RAM */
- data_ptr = (char *) packet;
- DM9000_outb(DM9000_MWCMD, DM9000_IO);
+ DM9000_DMP_PACKET("eth_send", packet, length);
-#ifdef CONFIG_DM9000_USE_8BIT
- /* Byte mode */
- for (i = 0; i < length; i++)
- DM9000_outb((data_ptr[i] & 0xff), DM9000_DATA);
+ DM9000_iow(DM9000_ISR, IMR_PTM); /* Clear Tx bit in ISR */
-#endif /* */
-#ifdef CONFIG_DM9000_USE_16BIT
- tmplen = (length + 1) / 2;
- for (i = 0; i < tmplen; i++)
- DM9000_outw(((u16 *) data_ptr)[i], DM9000_DATA);
-
-#endif /* */
-#ifdef CONFIG_DM9000_USE_32BIT
- tmplen = (length + 3) / 4;
- for (i = 0; i < tmplen; i++)
- DM9000_outl(((u32 *) data_ptr)[i], DM9000_DATA);
+ /* Move data to DM9000 TX RAM */
+ DM9000_outb(DM9000_MWCMD, DM9000_IO); /* Prepare for TX-data */
-#endif /* */
+ /* push the data to the TX-fifo */
+ (db->outblk)(packet, length);
/* Set TX length to DM9000 */
DM9000_iow(DM9000_TXPLL, length & 0xff);
DM9000_iow(DM9000_TXPLH, (length >> 8) & 0xff);
/* Issue TX polling command */
- DM9000_iow(DM9000_TCR, TCR_TXREQ); /* Cleared after TX complete */
+ DM9000_iow(DM9000_TCR, TCR_TXREQ); /* Cleared after TX complete */
/* wait for end of transmission */
tmo = get_timer(0) + 5 * CFG_HZ;
- while (DM9000_ior(DM9000_TCR) & TCR_TXREQ) {
+ while ( !(DM9000_ior(DM9000_NSR) & (NSR_TX1END | NSR_TX2END)) ||
+ !(DM9000_ior(DM9000_ISR) & IMR_PTM) ) {
if (get_timer(0) >= tmo) {
printf("transmission timeout\n");
break;
}
}
+ DM9000_iow(DM9000_ISR, IMR_PTM); /* Clear Tx bit in ISR */
+
DM9000_DBG("transmit done\n\n");
return 0;
}
{
u8 rxbyte, *rdptr = (u8 *) NetRxPackets[0];
u16 RxStatus, RxLen = 0;
- u32 tmplen, i;
-#ifdef CONFIG_DM9000_USE_32BIT
- u32 tmpdata;
-#endif
+ struct board_info *db = &dm9000_info;
- /* Check packet ready or not */
- DM9000_ior(DM9000_MRCMDX); /* Dummy read */
- rxbyte = DM9000_inb(DM9000_DATA); /* Got most updated data */
- if (rxbyte == 0)
+ /* Check packet ready or not, we must check
+ the ISR status first for DM9000A */
+ if (!(DM9000_ior(DM9000_ISR) & 0x01)) /* Rx-ISR bit must be set. */
return 0;
- /* Status check: this byte must be 0 or 1 */
- if (rxbyte > 1) {
- DM9000_iow(DM9000_RCR, 0x00); /* Stop Device */
- DM9000_iow(DM9000_ISR, 0x80); /* Stop INT request */
- DM9000_DBG("rx status check: %d\n", rxbyte);
- }
- DM9000_DBG("receiving packet\n");
-
- /* A packet ready now & Get status/length */
- DM9000_outb(DM9000_MRCMD, DM9000_IO);
-
-#ifdef CONFIG_DM9000_USE_8BIT
- RxStatus = DM9000_inb(DM9000_DATA) + (DM9000_inb(DM9000_DATA) << 8);
- RxLen = DM9000_inb(DM9000_DATA) + (DM9000_inb(DM9000_DATA) << 8);
-
-#endif /* */
-#ifdef CONFIG_DM9000_USE_16BIT
- RxStatus = DM9000_inw(DM9000_DATA);
- RxLen = DM9000_inw(DM9000_DATA);
-
-#endif /* */
-#ifdef CONFIG_DM9000_USE_32BIT
- tmpdata = DM9000_inl(DM9000_DATA);
- RxStatus = tmpdata;
- RxLen = tmpdata >> 16;
+ DM9000_iow(DM9000_ISR, 0x01); /* clear PR status latched in bit 0 */
-#endif /* */
- DM9000_DBG("rx status: 0x%04x rx len: %d\n", RxStatus, RxLen);
+ /* There is _at least_ 1 package in the fifo, read them all */
+ for (;;) {
+ DM9000_ior(DM9000_MRCMDX); /* Dummy read */
- /* Move data from DM9000 */
- /* Read received packet from RX SRAM */
-#ifdef CONFIG_DM9000_USE_8BIT
- for (i = 0; i < RxLen; i++)
- rdptr[i] = DM9000_inb(DM9000_DATA);
+ /* Get most updated data,
+ only look at bits 0:1, See application notes DM9000 */
+ rxbyte = DM9000_inb(DM9000_DATA) & 0x03;
-#endif /* */
-#ifdef CONFIG_DM9000_USE_16BIT
- tmplen = (RxLen + 1) / 2;
- for (i = 0; i < tmplen; i++)
- ((u16 *) rdptr)[i] = DM9000_inw(DM9000_DATA);
+ /* Status check: this byte must be 0 or 1 */
+ if (rxbyte > DM9000_PKT_RDY) {
+ DM9000_iow(DM9000_RCR, 0x00); /* Stop Device */
+ DM9000_iow(DM9000_ISR, 0x80); /* Stop INT request */
+ printf("DM9000 error: status check fail: 0x%x\n",
+ rxbyte);
+ return 0;
+ }
-#endif /* */
-#ifdef CONFIG_DM9000_USE_32BIT
- tmplen = (RxLen + 3) / 4;
- for (i = 0; i < tmplen; i++)
- ((u32 *) rdptr)[i] = DM9000_inl(DM9000_DATA);
+ if (rxbyte != DM9000_PKT_RDY)
+ return 0; /* No packet received, ignore */
+
+ DM9000_DBG("receiving packet\n");
+
+ /* A packet ready now & Get status/length */
+ (db->rx_status)(&RxStatus, &RxLen);
+
+ DM9000_DBG("rx status: 0x%04x rx len: %d\n", RxStatus, RxLen);
+
+ /* Move data from DM9000 */
+ /* Read received packet from RX SRAM */
+ (db->inblk)(rdptr, RxLen);
+
+ if ((RxStatus & 0xbf00) || (RxLen < 0x40)
+ || (RxLen > DM9000_PKT_MAX)) {
+ if (RxStatus & 0x100) {
+ printf("rx fifo error\n");
+ }
+ if (RxStatus & 0x200) {
+ printf("rx crc error\n");
+ }
+ if (RxStatus & 0x8000) {
+ printf("rx length error\n");
+ }
+ if (RxLen > DM9000_PKT_MAX) {
+ printf("rx length too big\n");
+ dm9000_reset();
+ }
+ } else {
+ DM9000_DMP_PACKET("eth_rx", rdptr, RxLen);
-#endif /* */
- if ((RxStatus & 0xbf00) || (RxLen < 0x40)
- || (RxLen > DM9000_PKT_MAX)) {
- if (RxStatus & 0x100) {
- printf("rx fifo error\n");
+ DM9000_DBG("passing packet to upper layer\n");
+ NetReceive(NetRxPackets[0], RxLen);
}
- if (RxStatus & 0x200) {
- printf("rx crc error\n");
- }
- if (RxStatus & 0x8000) {
- printf("rx length error\n");
- }
- if (RxLen > DM9000_PKT_MAX) {
- printf("rx length too big\n");
- dm9000_reset();
- }
- } else {
-
- /* Pass to upper layer */
- DM9000_DBG("passing packet to upper layer\n");
- NetReceive(NetRxPackets[0], RxLen);
- return RxLen;
}
return 0;
}
/* Fill the phyxcer register into REG_0C */
DM9000_iow(DM9000_EPAR, DM9000_PHY | reg);
DM9000_iow(DM9000_EPCR, 0xc); /* Issue phyxcer read command */
- udelay(100); /* Wait read complete */
+ udelay(100); /* Wait read complete */
DM9000_iow(DM9000_EPCR, 0x0); /* Clear phyxcer read command */
val = (DM9000_ior(DM9000_EPDRH) << 8) | DM9000_ior(DM9000_EPDRL);
/* The read data keeps on REG_0D & REG_0E */
- DM9000_DBG("phy_read(%d): %d\n", reg, val);
+ DM9000_DBG("phy_read(0x%x): 0x%x\n", reg, val);
return val;
}
DM9000_iow(DM9000_EPDRL, (value & 0xff));
DM9000_iow(DM9000_EPDRH, ((value >> 8) & 0xff));
DM9000_iow(DM9000_EPCR, 0xa); /* Issue phyxcer write command */
- udelay(500); /* Wait write complete */
+ udelay(500); /* Wait write complete */
DM9000_iow(DM9000_EPCR, 0x0); /* Clear phyxcer write command */
- DM9000_DBG("phy_write(reg:%d, value:%d)\n", reg, value);
+ DM9000_DBG("phy_write(reg:0x%x, value:0x%x)\n", reg, value);
}
-#endif /* CONFIG_DRIVER_DM9000 */
+#endif /* CONFIG_DRIVER_DM9000 */
projects / u-boot / commitdiff