void palmas_init_settings(void)
{
- return;
+#ifdef CONFIG_PALMAS_SMPS7_FPWM
+ int err;
+ /*
+ * Set SMPS7 (1.8 V I/O supply on platforms with TWL6035/37) to
+ * forced PWM mode. This reduces noise (but affects efficiency).
+ */
+ u8 val = SMPS_MODE_SLP_FPWM | SMPS_MODE_ACT_FPWM;
+ err = palmas_i2c_write_u8(TWL603X_CHIP_P1, SMPS7_CTRL, val);
+ if (err)
+ printf("palmas: could not force PWM for SMPS7: err = %d\n",
+ err);
+#endif
}
int palmas_mmc1_poweron_ldo(void)
{
u8 val = 0;
- /* set LDO9 TWL6035 to 3V */
- val = 0x2b; /* (3 -.9)*28 +1 */
-
- if (palmas_i2c_write_u8(0x48, LDO9_VOLTAGE, val)) {
- printf("twl6035: could not set LDO9 voltage.\n");
+#if defined(CONFIG_DRA7XX)
+ /*
+ * Currently valid for the dra7xx_evm board:
+ * Set TPS659038 LDO1 to 3.0 V
+ */
+ val = LDO_VOLT_3V0;
+ if (palmas_i2c_write_u8(TPS65903X_CHIP_P1, LDO1_VOLTAGE, val)) {
+ printf("tps65903x: could not set LDO1 voltage.\n");
+ return 1;
+ }
+ /* TURN ON LDO1 */
+ val = RSC_MODE_SLEEP | RSC_MODE_ACTIVE;
+ if (palmas_i2c_write_u8(TPS65903X_CHIP_P1, LDO1_CTRL, val)) {
+ printf("tps65903x: could not turn on LDO1.\n");
return 1;
}
+ return 0;
+#else
+ /*
+ * We assume that this is a OMAP543X + TWL603X board:
+ * Set TWL6035/37 LDO9 to 3.0 V
+ */
+ val = LDO_VOLT_3V0;
+ return twl603x_mmc1_set_ldo9(val);
+#endif
+}
- /* TURN ON LDO9 */
- val = LDO_ON | LDO_MODE_SLEEP | LDO_MODE_ACTIVE;
+/*
+ * On some OMAP5 + TWL603X hardware the SD card socket and LDO9_IN are
+ * powered by an external 3.3 V regulator, while the output of LDO9
+ * supplies VDDS_SDCARD for the OMAP5 interface only. This implies that
+ * LDO9 could be set to 'bypass' mode when required (e.g. for 3.3 V cards).
+ */
+int twl603x_mmc1_set_ldo9(u8 vsel)
+{
+ u8 cval = 0, vval = 0; /* Off by default */
+ int err;
- if (palmas_i2c_write_u8(0x48, LDO9_CTRL, val)) {
- printf("twl6035: could not turn on LDO9.\n");
- return 1;
+ if (vsel) {
+ /* Turn on */
+ if (vsel > LDO_VOLT_3V3) {
+ /* Put LDO9 in bypass */
+ cval = LDO9_BYP_EN | RSC_MODE_SLEEP | RSC_MODE_ACTIVE;
+ vval = LDO_VOLT_3V3;
+ } else {
+ cval = RSC_MODE_SLEEP | RSC_MODE_ACTIVE;
+ vval = vsel & 0x3f;
+ }
+ }
+ err = palmas_i2c_write_u8(TWL603X_CHIP_P1, LDO9_VOLTAGE, vval);
+ if (err) {
+ printf("twl603x: could not set LDO9 %s: err = %d\n",
+ vsel > LDO_VOLT_3V3 ? "bypass" : "voltage", err);
+ return err;
}
+ err = palmas_i2c_write_u8(TWL603X_CHIP_P1, LDO9_CTRL, cval);
+ if (err)
+ printf("twl603x: could not turn %s LDO9: err = %d\n",
+ cval ? "on" : "off", err);
+ return err;
+}
- return 0;
+#ifdef CONFIG_PALMAS_AUDPWR
+/*
+ * Turn audio codec power and 32 kHz clock on/off. Use for
+ * testing OMAP543X + TWL603X + TWL604X boards only.
+ */
+int twl603x_audio_power(u8 on)
+{
+ u8 cval = 0, vval = 0, c32k = 0;
+ int err;
+
+ if (on) {
+ vval = SMPS_VOLT_2V1;
+ cval = SMPS_MODE_SLP_AUTO | SMPS_MODE_ACT_AUTO;
+ c32k = RSC_MODE_SLEEP | RSC_MODE_ACTIVE;
+ }
+ /* Set SMPS9 to 2.1 V (for TWL604x), or to 0 (off) */
+ err = palmas_i2c_write_u8(TWL603X_CHIP_P1, SMPS9_VOLTAGE, vval);
+ if (err) {
+ printf("twl603x: could not set SMPS9 voltage: err = %d\n",
+ err);
+ return err;
+ }
+ /* Turn on or off SMPS9 */
+ err = palmas_i2c_write_u8(TWL603X_CHIP_P1, SMPS9_CTRL, cval);
+ if (err) {
+ printf("twl603x: could not turn SMPS9 %s: err = %d\n",
+ cval ? "on" : "off", err);
+ return err;
+ }
+ /* Output 32 kHz clock on or off */
+ err = palmas_i2c_write_u8(TWL603X_CHIP_P1, CLK32KGAUDIO_CTRL, c32k);
+ if (err)
+ printf("twl603x: could not turn CLK32KGAUDIO %s: err = %d\n",
+ c32k ? "on" : "off", err);
+ return err;
+}
+#endif
+
+/*
+ * Enable/disable back-up battery (or super cap) charging on TWL6035/37.
+ * Please use defined BB_xxx values.
+ */
+int twl603x_enable_bb_charge(u8 bb_fields)
+{
+ u8 val = bb_fields & 0x0f;
+ int err;
+
+ val |= (VRTC_EN_SLP | VRTC_EN_OFF | VRTC_PWEN);
+ err = palmas_i2c_write_u8(TWL603X_CHIP_P1, BB_VRTC_CTRL, val);
+ if (err)
+ printf("twl603x: could not set BB_VRTC_CTRL to 0x%02x: err = %d\n",
+ val, err);
+ return err;
}
#include <common.h>
#include <i2c.h>
-/* I2C chip addresses */
-#define PALMAS_CHIP_ADDR 0x48
+/* I2C chip addresses, TW6035/37 */
+#define TWL603X_CHIP_P1 0x48 /* Page 1 */
+#define TWL603X_CHIP_P2 0x49 /* Page 2 */
+#define TWL603X_CHIP_P3 0x4a /* Page 3 */
-/* 0x1XY translates to page 1, register address 0xXY */
+/* TPS659038/39 */
+#define TPS65903X_CHIP_P1 0x58 /* Page 1 */
+
+/* Page 1 registers (0x1XY translates to page 1, reg addr 0xXY): */
+
+/* LDO1 control/voltage */
+#define LDO1_CTRL 0x50
+#define LDO1_VOLTAGE 0x51
+
+/* LDO9 control/voltage */
#define LDO9_CTRL 0x60
#define LDO9_VOLTAGE 0x61
-/* Bit field definitions for LDOx_CTRL */
-#define LDO_ON (1 << 4)
-#define LDO_MODE_SLEEP (1 << 2)
-#define LDO_MODE_ACTIVE (1 << 0)
+/* LDOUSB control/voltage */
+#define LDOUSB_CTRL 0x64
+#define LDOUSB_VOLTAGE 0x65
+
+/* Control of 32 kHz audio clock */
+#define CLK32KGAUDIO_CTRL 0xd5
+
+/* SYSEN2_CTRL for VCC_3v3_AUX supply on the sEVM */
+#define SYSEN2_CTRL 0xd9
+
+/*
+ * Bit field definitions for LDOx_CTRL, SYSENx_CTRL
+ * and some other xxx_CTRL resources:
+ */
+#define LDO9_BYP_EN (1 << 6) /* LDO9 only! */
+#define RSC_STAT_ON (1 << 4) /* RO status bit! */
+#define RSC_MODE_SLEEP (1 << 2)
+#define RSC_MODE_ACTIVE (1 << 0)
+
+/* Some LDO voltage values */
+#define LDO_VOLT_OFF 0
+#define LDO_VOLT_1V8 0x13
+#define LDO_VOLT_3V0 0x2b
+#define LDO_VOLT_3V3 0x31
+/* Request bypass, LDO9 only */
+#define LDO9_BYPASS 0x3f
+
+/* SMPS7_CTRL */
+#define SMPS7_CTRL 0x30
+
+/* SMPS9_CTRL */
+#define SMPS9_CTRL 0x38
+#define SMPS9_VOLTAGE 0x3b
+
+/* Bit field definitions for SMPSx_CTRL */
+#define SMPS_MODE_ACT_AUTO 1
+#define SMPS_MODE_ACT_ECO 2
+#define SMPS_MODE_ACT_FPWM 3
+#define SMPS_MODE_SLP_AUTO (1 << 2)
+#define SMPS_MODE_SLP_ECO (2 << 2)
+#define SMPS_MODE_SLP_FPWM (3 << 2)
+
+/*
+ * Some popular SMPS voltages, all with RANGE=1; note
+ * that RANGE cannot be changed on the fly
+ */
+#define SMPS_VOLT_OFF 0
+#define SMPS_VOLT_1V2 0x90
+#define SMPS_VOLT_1V8 0xae
+#define SMPS_VOLT_2V1 0xbd
+#define SMPS_VOLT_3V0 0xea
+#define SMPS_VOLT_3V3 0xf9
+
+/* Backup Battery & VRTC Control */
+#define BB_VRTC_CTRL 0xa8
+/* Bit definitions for BB_VRTC_CTRL */
+#define VRTC_EN_SLP (1 << 6)
+#define VRTC_EN_OFF (1 << 5)
+#define VRTC_PWEN (1 << 4)
+#define BB_LOW_ICHRG (1 << 3)
+#define BB_HIGH_ICHRG (0 << 3)
+#define BB_VSEL_3V0 (0 << 1)
+#define BB_VSEL_2V5 (1 << 1)
+#define BB_VSEL_3V15 (2 << 1)
+#define BB_VSEL_VBAT (3 << 1)
+#define BB_CHRG_EN (1 << 0)
/*
* Functions to read and write from TPS659038/TWL6035/TWL6037
void palmas_init_settings(void);
int palmas_mmc1_poweron_ldo(void);
+int twl603x_mmc1_set_ldo9(u8 vsel);
+int twl603x_audio_power(u8 on);
+int twl603x_enable_bb_charge(u8 bb_fields);
#endif /* PALMAS_H */
projects / u-boot / commitdiff