This board has not been converted to DM_SERIAL by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: David Müller <d.mueller@elsoft.ch>
bool "Support VCMA9"
select CPU_ARM920T
-config TARGET_SMDK2410
- bool "Support smdk2410"
- select CPU_ARM920T
-
config TARGET_ASPENITE
bool "Support aspenite"
select CPU_ARM926EJS
source "board/phytec/pcm051/Kconfig"
source "board/phytec/pcm052/Kconfig"
source "board/ppcag/bg0900/Kconfig"
-source "board/samsung/smdk2410/Kconfig"
source "board/sandisk/sansa_fuze_plus/Kconfig"
source "board/schulercontrol/sc_sps_1/Kconfig"
source "board/siemens/draco/Kconfig"
+++ /dev/null
-if TARGET_SMDK2410
-
-config SYS_BOARD
- default "smdk2410"
-
-config SYS_VENDOR
- default "samsung"
-
-config SYS_SOC
- default "s3c24x0"
-
-config SYS_CONFIG_NAME
- default "smdk2410"
-
-endif
+++ /dev/null
-SMDK2410 BOARD
-M: David Müller <d.mueller@elsoft.ch>
-S: Maintained
-F: board/samsung/smdk2410/
-F: include/configs/smdk2410.h
-F: configs/smdk2410_defconfig
+++ /dev/null
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := smdk2410.o
-obj-y += lowlevel_init.o
+++ /dev/null
-/*
- * Memory Setup stuff - taken from blob memsetup.S
- *
- * Copyright (C) 1999 2000 2001 Erik Mouw (J.A.K.Mouw@its.tudelft.nl) and
- * Jan-Derk Bakker (J.D.Bakker@its.tudelft.nl)
- *
- * Modified for the Samsung SMDK2410 by
- * (C) Copyright 2002
- * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-
-#include <config.h>
-
-/* some parameters for the board */
-
-/*
- *
- * Taken from linux/arch/arm/boot/compressed/head-s3c2410.S
- *
- * Copyright (C) 2002 Samsung Electronics SW.LEE <hitchcar@sec.samsung.com>
- *
- */
-
-#define BWSCON 0x48000000
-
-/* BWSCON */
-#define DW8 (0x0)
-#define DW16 (0x1)
-#define DW32 (0x2)
-#define WAIT (0x1<<2)
-#define UBLB (0x1<<3)
-
-#define B1_BWSCON (DW32)
-#define B2_BWSCON (DW16)
-#define B3_BWSCON (DW16 + WAIT + UBLB)
-#define B4_BWSCON (DW16)
-#define B5_BWSCON (DW16)
-#define B6_BWSCON (DW32)
-#define B7_BWSCON (DW32)
-
-/* BANK0CON */
-#define B0_Tacs 0x0 /* 0clk */
-#define B0_Tcos 0x0 /* 0clk */
-#define B0_Tacc 0x7 /* 14clk */
-#define B0_Tcoh 0x0 /* 0clk */
-#define B0_Tah 0x0 /* 0clk */
-#define B0_Tacp 0x0
-#define B0_PMC 0x0 /* normal */
-
-/* BANK1CON */
-#define B1_Tacs 0x0 /* 0clk */
-#define B1_Tcos 0x0 /* 0clk */
-#define B1_Tacc 0x7 /* 14clk */
-#define B1_Tcoh 0x0 /* 0clk */
-#define B1_Tah 0x0 /* 0clk */
-#define B1_Tacp 0x0
-#define B1_PMC 0x0
-
-#define B2_Tacs 0x0
-#define B2_Tcos 0x0
-#define B2_Tacc 0x7
-#define B2_Tcoh 0x0
-#define B2_Tah 0x0
-#define B2_Tacp 0x0
-#define B2_PMC 0x0
-
-#define B3_Tacs 0x0 /* 0clk */
-#define B3_Tcos 0x3 /* 4clk */
-#define B3_Tacc 0x7 /* 14clk */
-#define B3_Tcoh 0x1 /* 1clk */
-#define B3_Tah 0x0 /* 0clk */
-#define B3_Tacp 0x3 /* 6clk */
-#define B3_PMC 0x0 /* normal */
-
-#define B4_Tacs 0x0 /* 0clk */
-#define B4_Tcos 0x0 /* 0clk */
-#define B4_Tacc 0x7 /* 14clk */
-#define B4_Tcoh 0x0 /* 0clk */
-#define B4_Tah 0x0 /* 0clk */
-#define B4_Tacp 0x0
-#define B4_PMC 0x0 /* normal */
-
-#define B5_Tacs 0x0 /* 0clk */
-#define B5_Tcos 0x0 /* 0clk */
-#define B5_Tacc 0x7 /* 14clk */
-#define B5_Tcoh 0x0 /* 0clk */
-#define B5_Tah 0x0 /* 0clk */
-#define B5_Tacp 0x0
-#define B5_PMC 0x0 /* normal */
-
-#define B6_MT 0x3 /* SDRAM */
-#define B6_Trcd 0x1
-#define B6_SCAN 0x1 /* 9bit */
-
-#define B7_MT 0x3 /* SDRAM */
-#define B7_Trcd 0x1 /* 3clk */
-#define B7_SCAN 0x1 /* 9bit */
-
-/* REFRESH parameter */
-#define REFEN 0x1 /* Refresh enable */
-#define TREFMD 0x0 /* CBR(CAS before RAS)/Auto refresh */
-#define Trp 0x0 /* 2clk */
-#define Trc 0x3 /* 7clk */
-#define Tchr 0x2 /* 3clk */
-#define REFCNT 1113 /* period=15.6us, HCLK=60Mhz, (2048+1-15.6*60) */
-/**************************************/
-
-.globl lowlevel_init
-lowlevel_init:
- /* memory control configuration */
- /* make r0 relative the current location so that it */
- /* reads SMRDATA out of FLASH rather than memory ! */
- ldr r0, =SMRDATA
- ldr r1, =CONFIG_SYS_TEXT_BASE
- sub r0, r0, r1
- ldr r1, =BWSCON /* Bus Width Status Controller */
- add r2, r0, #13*4
-0:
- ldr r3, [r0], #4
- str r3, [r1], #4
- cmp r2, r0
- bne 0b
-
- /* everything is fine now */
- mov pc, lr
-
- .ltorg
-/* the literal pools origin */
-
-SMRDATA:
- .word (0+(B1_BWSCON<<4)+(B2_BWSCON<<8)+(B3_BWSCON<<12)+(B4_BWSCON<<16)+(B5_BWSCON<<20)+(B6_BWSCON<<24)+(B7_BWSCON<<28))
- .word ((B0_Tacs<<13)+(B0_Tcos<<11)+(B0_Tacc<<8)+(B0_Tcoh<<6)+(B0_Tah<<4)+(B0_Tacp<<2)+(B0_PMC))
- .word ((B1_Tacs<<13)+(B1_Tcos<<11)+(B1_Tacc<<8)+(B1_Tcoh<<6)+(B1_Tah<<4)+(B1_Tacp<<2)+(B1_PMC))
- .word ((B2_Tacs<<13)+(B2_Tcos<<11)+(B2_Tacc<<8)+(B2_Tcoh<<6)+(B2_Tah<<4)+(B2_Tacp<<2)+(B2_PMC))
- .word ((B3_Tacs<<13)+(B3_Tcos<<11)+(B3_Tacc<<8)+(B3_Tcoh<<6)+(B3_Tah<<4)+(B3_Tacp<<2)+(B3_PMC))
- .word ((B4_Tacs<<13)+(B4_Tcos<<11)+(B4_Tacc<<8)+(B4_Tcoh<<6)+(B4_Tah<<4)+(B4_Tacp<<2)+(B4_PMC))
- .word ((B5_Tacs<<13)+(B5_Tcos<<11)+(B5_Tacc<<8)+(B5_Tcoh<<6)+(B5_Tah<<4)+(B5_Tacp<<2)+(B5_PMC))
- .word ((B6_MT<<15)+(B6_Trcd<<2)+(B6_SCAN))
- .word ((B7_MT<<15)+(B7_Trcd<<2)+(B7_SCAN))
- .word ((REFEN<<23)+(TREFMD<<22)+(Trp<<20)+(Trc<<18)+(Tchr<<16)+REFCNT)
- .word 0x32
- .word 0x30
- .word 0x30
+++ /dev/null
-/*
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * (C) Copyright 2002, 2010
- * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-#include <asm/io.h>
-#include <asm/arch/s3c24x0_cpu.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define FCLK_SPEED 1
-
-#if (FCLK_SPEED == 0) /* Fout = 203MHz, Fin = 12MHz for Audio */
-#define M_MDIV 0xC3
-#define M_PDIV 0x4
-#define M_SDIV 0x1
-#elif (FCLK_SPEED == 1) /* Fout = 202.8MHz */
-#define M_MDIV 0xA1
-#define M_PDIV 0x3
-#define M_SDIV 0x1
-#endif
-
-#define USB_CLOCK 1
-
-#if (USB_CLOCK == 0)
-#define U_M_MDIV 0xA1
-#define U_M_PDIV 0x3
-#define U_M_SDIV 0x1
-#elif (USB_CLOCK == 1)
-#define U_M_MDIV 0x48
-#define U_M_PDIV 0x3
-#define U_M_SDIV 0x2
-#endif
-
-static inline void pll_delay(unsigned long loops)
-{
- __asm__ volatile ("1:\n"
- "subs %0, %1, #1\n"
- "bne 1b" : "=r" (loops) : "0" (loops));
-}
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-
-int board_early_init_f(void)
-{
- struct s3c24x0_clock_power * const clk_power =
- s3c24x0_get_base_clock_power();
- struct s3c24x0_gpio * const gpio = s3c24x0_get_base_gpio();
-
- /* to reduce PLL lock time, adjust the LOCKTIME register */
- writel(0xFFFFFF, &clk_power->locktime);
-
- /* configure MPLL */
- writel((M_MDIV << 12) + (M_PDIV << 4) + M_SDIV,
- &clk_power->mpllcon);
-
- /* some delay between MPLL and UPLL */
- pll_delay(4000);
-
- /* configure UPLL */
- writel((U_M_MDIV << 12) + (U_M_PDIV << 4) + U_M_SDIV,
- &clk_power->upllcon);
-
- /* some delay between MPLL and UPLL */
- pll_delay(8000);
-
- /* set up the I/O ports */
- writel(0x007FFFFF, &gpio->gpacon);
- writel(0x00044555, &gpio->gpbcon);
- writel(0x000007FF, &gpio->gpbup);
- writel(0xAAAAAAAA, &gpio->gpccon);
- writel(0x0000FFFF, &gpio->gpcup);
- writel(0xAAAAAAAA, &gpio->gpdcon);
- writel(0x0000FFFF, &gpio->gpdup);
- writel(0xAAAAAAAA, &gpio->gpecon);
- writel(0x0000FFFF, &gpio->gpeup);
- writel(0x000055AA, &gpio->gpfcon);
- writel(0x000000FF, &gpio->gpfup);
- writel(0xFF95FFBA, &gpio->gpgcon);
- writel(0x0000FFFF, &gpio->gpgup);
- writel(0x002AFAAA, &gpio->gphcon);
- writel(0x000007FF, &gpio->gphup);
-
- return 0;
-}
-
-int board_init(void)
-{
- /* arch number of SMDK2410-Board */
- gd->bd->bi_arch_number = MACH_TYPE_SMDK2410;
-
- /* adress of boot parameters */
- gd->bd->bi_boot_params = 0x30000100;
-
- icache_enable();
- dcache_enable();
-
- return 0;
-}
-
-int dram_init(void)
-{
- /* dram_init must store complete ramsize in gd->ram_size */
- gd->ram_size = PHYS_SDRAM_1_SIZE;
- return 0;
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_CS8900
- rc = cs8900_initialize(0, CONFIG_CS8900_BASE);
-#endif
- return rc;
-}
-#endif
-
-/*
- * Hardcoded flash setup:
- * Flash 0 is a non-CFI AMD AM29LV800BB flash.
- */
-ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info)
-{
- info->portwidth = FLASH_CFI_16BIT;
- info->chipwidth = FLASH_CFI_BY16;
- info->interface = FLASH_CFI_X16;
- return 1;
-}
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_TARGET_SMDK2410=y
-CONFIG_BOOTDELAY=5
-# CONFIG_SYS_STDIO_DEREGISTER is not set
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="SMDK2410 # "
-CONFIG_CMD_USB=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_UBI=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_KEYBOARD=y
+++ /dev/null
-/*
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- * Gary Jennejohn <garyj@denx.de>
- * David Mueller <d.mueller@elsoft.ch>
- *
- * Configuation settings for the SAMSUNG SMDK2410 board.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_S3C24X0 /* This is a SAMSUNG S3C24x0-type SoC */
-#define CONFIG_S3C2410 /* specifically a SAMSUNG S3C2410 SoC */
-#define CONFIG_SMDK2410 /* on a SAMSUNG SMDK2410 Board */
-
-#define CONFIG_SYS_TEXT_BASE 0x0
-
-#define CONFIG_SYS_ARM_CACHE_WRITETHROUGH
-
-/* input clock of PLL (the SMDK2410 has 12MHz input clock) */
-#define CONFIG_SYS_CLK_FREQ 12000000
-
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
-
-/*
- * Hardware drivers
- */
-#define CONFIG_CS8900 /* we have a CS8900 on-board */
-#define CONFIG_CS8900_BASE 0x19000300
-#define CONFIG_CS8900_BUS16 /* the Linux driver does accesses as shorts */
-
-/*
- * select serial console configuration
- */
-#define CONFIG_S3C24X0_SERIAL
-#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on SMDK2410 */
-
-/************************************************************
- * USB support (currently only works with D-cache off)
- ************************************************************/
-#define CONFIG_USB_OHCI
-#define CONFIG_USB_OHCI_S3C24XX
-#define CONFIG_DOS_PARTITION
-
-/************************************************************
- * RTC
- ************************************************************/
-#define CONFIG_RTC_S3C24X0
-
-#define CONFIG_BAUDRATE 115200
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_BSP
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_REGINFO
-
-#define CONFIG_CMDLINE_EDITING
-
-/* autoboot */
-#define CONFIG_BOOT_RETRY_TIME -1
-#define CONFIG_RESET_TO_RETRY
-
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_IPADDR 10.0.0.110
-#define CONFIG_SERVERIP 10.0.0.1
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_CBSIZE 256
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
-
-#define CONFIG_SYS_MEMTEST_START 0x30000000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x33F00000 /* 63 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x30800000
-
-/* support additional compression methods */
-#define CONFIG_BZIP2
-#define CONFIG_LZO
-#define CONFIG_LZMA
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
-#define PHYS_SDRAM_1 0x30000000 /* SDRAM Bank #1 */
-#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */
-
-#define PHYS_FLASH_1 0x00000000 /* Flash Bank #0 */
-
-#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_FLASH_CFI_LEGACY
-#define CONFIG_SYS_FLASH_LEGACY_512Kx16
-#define CONFIG_FLASH_SHOW_PROGRESS 45
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_MAX_FLASH_SECT (19)
-
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x070000)
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_SIZE 0x10000
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/*
- * Size of malloc() pool
- * BZIP2 / LZO / LZMA need a lot of RAM
- */
-#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
-
-#define CONFIG_SYS_MONITOR_LEN (448 * 1024)
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-
-/*
- * NAND configuration
- */
-#ifdef CONFIG_CMD_NAND
-#define CONFIG_NAND_S3C2410
-#define CONFIG_SYS_S3C2410_NAND_HWECC
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE 0x4E000000
-#endif
-
-/*
- * File system
- */
-#define CONFIG_CMD_UBIFS
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_DEVICE
-#define CONFIG_MTD_PARTITIONS
-#define CONFIG_YAFFS2
-#define CONFIG_RBTREE
-
-/* additions for new relocation code, must be added to all boards */
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - \
- GENERATED_GBL_DATA_SIZE)
-
-#define CONFIG_BOARD_EARLY_INIT_F
-
-#endif /* __CONFIG_H */
CONFIG_ARCH_RPC
CONFIG_ARCH_S3C2440
CONFIG_ARCH_SHARK
-CONFIG_ARCH_SMDK2410
CONFIG_ARCH_TEGRA
CONFIG_ARCH_USE_BUILTIN_BSWAP
CONFIG_ARCH_VERSATILE_PB
CONFIG_SMC_GCTL_VAL
CONFIG_SMC_USE_32_BIT
CONFIG_SMC_USE_IOFUNCS
-CONFIG_SMDK2410
CONFIG_SMDK5420
CONFIG_SMDKC100
CONFIG_SMDKV310
projects / u-boot / commitdiff