--- /dev/null
- #define CONFIG_USB_XHCI
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __LS1012ARDB_H__
+#define __LS1012ARDB_H__
+
+#include "ls1012a_common.h"
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 1
+#define CONFIG_NR_DRAM_BANKS 2
+#define CONFIG_SYS_SDRAM_SIZE 0x20000000
+
+#define CONFIG_SYS_MMDC_CORE_CONTROL_1 0x04180000
+#define CONFIG_SYS_MMDC_CORE_CONTROL_2 0x84180000
+
+#define CONFIG_CMD_MEMINFO
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_MEMTEST_START 0x80000000
+#define CONFIG_SYS_MEMTEST_END 0x9fffffff
+
+/*
+* USB
+*/
+#define CONFIG_HAS_FSL_XHCI_USB
+
+#ifdef CONFIG_HAS_FSL_XHCI_USB
- #define CONFIG_USB_XHCI_DWC3
+#define CONFIG_USB_XHCI_FSL
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
+#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
+#define CONFIG_USB_STORAGE
+#endif
+
+#define CONFIG_CMD_MEMINFO
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_MEMTEST_START 0x80000000
+#define CONFIG_SYS_MEMTEST_END 0x9fffffff
+
+#endif /* __LS1012ARDB_H__ */
--- /dev/null
- #define CONFIG_USB_XHCI
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __LS1012AQDS_H__
+#define __LS1012AQDS_H__
+
+#include "ls1012a_common.h"
+
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 1
+#define CONFIG_NR_DRAM_BANKS 2
+#define CONFIG_SYS_SDRAM_SIZE 0x40000000
+
+#define CONFIG_SYS_MMDC_CORE_CONTROL_1 0x05180000
+#define CONFIG_SYS_MMDC_CORE_CONTROL_2 0x85180000
+
+/*
+ * QIXIS Definitions
+ */
+#define CONFIG_FSL_QIXIS
+
+#ifdef CONFIG_FSL_QIXIS
+#define CONFIG_QIXIS_I2C_ACCESS
+#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
+#define QIXIS_LBMAP_BRDCFG_REG 0x04
+#define QIXIS_LBMAP_SWITCH 6
+#define QIXIS_LBMAP_MASK 0xf7
+#define QIXIS_LBMAP_SHIFT 0
+#define QIXIS_LBMAP_DFLTBANK 0x00
+#define QIXIS_LBMAP_ALTBANK 0x08
+#define QIXIS_RST_CTL_RESET 0x41
+#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
+#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
+#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
+#endif
+
+/*
+ * I2C bus multiplexer
+ */
+#define I2C_MUX_PCA_ADDR_PRI 0x77
+#define I2C_MUX_PCA_ADDR_SEC 0x76 /* Secondary multiplexer */
+#define I2C_RETIMER_ADDR 0x18
+#define I2C_MUX_CH_DEFAULT 0x8
+#define I2C_MUX_CH_CH7301 0xC
+#define I2C_MUX_CH5 0xD
+#define I2C_MUX_CH7 0xF
+
+#define I2C_MUX_CH_VOL_MONITOR 0xa
+
+/*
+* RTC configuration
+*/
+#define RTC
+#define CONFIG_RTC_PCF8563 1
+#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/
+#define CONFIG_CMD_DATE
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_CMD_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+
+
+/* Voltage monitor on channel 2*/
+#define I2C_VOL_MONITOR_ADDR 0x40
+#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
+#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
+#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
+
+/* DSPI */
+#define CONFIG_FSL_DSPI1
+#define CONFIG_DEFAULT_SPI_BUS 1
+
+#define CONFIG_CMD_SPI
+#define MMAP_DSPI DSPI1_BASE_ADDR
+
+#define CONFIG_SYS_DSPI_CTAR0 1
+
+#define CONFIG_SYS_DSPI_CTAR1 (DSPI_CTAR_TRSZ(7) | DSPI_CTAR_PCSSCK_1CLK |\
+ DSPI_CTAR_PASC(0) | DSPI_CTAR_PDT(0) | \
+ DSPI_CTAR_CSSCK(2) | DSPI_CTAR_ASC(0) | \
+ DSPI_CTAR_DT(0))
+#define CONFIG_SPI_FLASH_SST /* cs1 */
+
+#define CONFIG_SYS_DSPI_CTAR2 (DSPI_CTAR_TRSZ(7) | DSPI_CTAR_PCSSCK_1CLK |\
+ DSPI_CTAR_PASC(0) | DSPI_CTAR_PDT(0) | \
+ DSPI_CTAR_CSSCK(0) | DSPI_CTAR_ASC(0) | \
+ DSPI_CTAR_DT(0))
+#define CONFIG_SPI_FLASH_STMICRO /* cs2 */
+
+#define CONFIG_SYS_DSPI_CTAR3 (DSPI_CTAR_TRSZ(7) | DSPI_CTAR_PCSSCK_1CLK |\
+ DSPI_CTAR_PASC(0) | DSPI_CTAR_PDT(0) | \
+ DSPI_CTAR_CSSCK(2) | DSPI_CTAR_ASC(0) | \
+ DSPI_CTAR_DT(0))
+#define CONFIG_SPI_FLASH_EON /* cs3 */
+
+#define CONFIG_SF_DEFAULT_SPEED 10000000
+#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
+#define CONFIG_SF_DEFAULT_BUS 1
+#define CONFIG_SF_DEFAULT_CS 0
+
+/*
+* USB
+*/
+/* EHCI Support - disbaled by default */
+/*#define CONFIG_HAS_FSL_DR_USB*/
+
+#ifdef CONFIG_HAS_FSL_DR_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#endif
+
+/*XHCI Support - enabled by default*/
+#define CONFIG_HAS_FSL_XHCI_USB
+
+#ifdef CONFIG_HAS_FSL_XHCI_USB
- #define CONFIG_USB_XHCI_DWC3
+#define CONFIG_USB_XHCI_FSL
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
+#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
+#define CONFIG_USB_STORAGE
+#endif
+
+/* MMC */
+#define CONFIG_MMC
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
+#define CONFIG_GENERIC_MMC
+#define CONFIG_DOS_PARTITION
+#endif
+
+/* SATA */
+#define CONFIG_LIBATA
+#define CONFIG_SCSI
+#define CONFIG_SCSI_AHCI
+#define CONFIG_SCSI_AHCI_PLAT
+#define CONFIG_CMD_SCSI
+#define CONFIG_DOS_PARTITION
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_SYS_SATA AHCI_BASE_ADDR
+
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
+#define CONFIG_SYS_SCSI_MAX_LUN 1
+#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+ CONFIG_SYS_SCSI_MAX_LUN)
+#define CONFIG_PCI /* Enable PCI/PCIE */
+#define CONFIG_PCIE1 /* PCIE controller 1 */
+#define CONFIG_PCIE_LAYERSCAPE /* Use common FSL Layerscape PCIe code */
+#define FSL_PCIE_COMPAT "fsl,ls1043a-pcie"
+
+#define CONFIG_SYS_PCI_64BIT
+
+#define CONFIG_SYS_PCIE_CFG0_PHYS_OFF 0x00000000
+#define CONFIG_SYS_PCIE_CFG0_SIZE 0x00001000 /* 4k */
+#define CONFIG_SYS_PCIE_CFG1_PHYS_OFF 0x00001000
+#define CONFIG_SYS_PCIE_CFG1_SIZE 0x00001000 /* 4k */
+
+#define CONFIG_SYS_PCIE_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE_IO_PHYS_OFF 0x00010000
+#define CONFIG_SYS_PCIE_IO_SIZE 0x00010000 /* 64k */
+
+#define CONFIG_SYS_PCIE_MEM_BUS 0x08000000
+#define CONFIG_SYS_PCIE_MEM_PHYS_OFF 0x04000000
+#define CONFIG_SYS_PCIE_MEM_SIZE 0x80000000 /* 128M */
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP
+#define CONFIG_PCI_SCAN_SHOW
+#define CONFIG_CMD_PCI
+
+#define CONFIG_CMD_MEMINFO
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_MEMTEST_START 0x80000000
+#define CONFIG_SYS_MEMTEST_END 0x9fffffff
+
+#define CONFIG_MISC_INIT_R
+
+#endif /* __LS1012AQDS_H__ */
--- /dev/null
- #define CONFIG_USB_XHCI
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __LS1012ARDB_H__
+#define __LS1012ARDB_H__
+
+#include "ls1012a_common.h"
+
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 1
+#define CONFIG_NR_DRAM_BANKS 2
+#define CONFIG_SYS_SDRAM_SIZE 0x40000000
+
+#define CONFIG_SYS_MMDC_CORE_CONTROL_1 0x05180000
+#define CONFIG_SYS_MMDC_CORE_CONTROL_2 0x85180000
+
+#define CONFIG_CMD_MEMINFO
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_MEMTEST_START 0x80000000
+#define CONFIG_SYS_MEMTEST_END 0x9fffffff
+
+/*
+* USB
+*/
+#define CONFIG_HAS_FSL_XHCI_USB
+
+#ifdef CONFIG_HAS_FSL_XHCI_USB
- #define CONFIG_USB_XHCI_DWC3
+#define CONFIG_USB_XHCI_FSL
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
+#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
+#define CONFIG_USB_STORAGE
+#endif
+
+/*
+ * I2C IO expander
+ */
+
+#define I2C_MUX_IO1_ADDR 0x24
+#define __SW_BOOT_MASK 0xFC
+#define __SW_BOOT_EMU 0x10
+#define __SW_BOOT_BANK1 0x00
+#define __SW_BOOT_BANK2 0x01
+#define __SW_REV_MASK 0x07
+#define __SW_REV_A 0xF8
+#define __SW_REV_B 0xF0
+
+/* MMC */
+#define CONFIG_MMC
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
+#define CONFIG_GENERIC_MMC
+#define CONFIG_DOS_PARTITION
+#endif
+
+/* SATA */
+#define CONFIG_LIBATA
+#define CONFIG_SCSI
+#define CONFIG_SCSI_AHCI
+#define CONFIG_SCSI_AHCI_PLAT
+#define CONFIG_CMD_SCSI
+#define CONFIG_DOS_PARTITION
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_SYS_SATA AHCI_BASE_ADDR
+
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
+#define CONFIG_SYS_SCSI_MAX_LUN 1
+#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
+ CONFIG_SYS_SCSI_MAX_LUN)
+#define CONFIG_PCI /* Enable PCI/PCIE */
+#define CONFIG_PCIE1 /* PCIE controller 1 */
+#define CONFIG_PCIE_LAYERSCAPE /* Use common FSL Layerscape PCIe code */
+#define FSL_PCIE_COMPAT "fsl,ls1043a-pcie"
+
+#define CONFIG_SYS_PCI_64BIT
+
+#define CONFIG_SYS_PCIE_CFG0_PHYS_OFF 0x00000000
+#define CONFIG_SYS_PCIE_CFG0_SIZE 0x00001000 /* 4k */
+#define CONFIG_SYS_PCIE_CFG1_PHYS_OFF 0x00001000
+#define CONFIG_SYS_PCIE_CFG1_SIZE 0x00001000 /* 4k */
+
+#define CONFIG_SYS_PCIE_IO_BUS 0x00000000
+#define CONFIG_SYS_PCIE_IO_PHYS_OFF 0x00010000
+#define CONFIG_SYS_PCIE_IO_SIZE 0x00010000 /* 64k */
+
+#define CONFIG_SYS_PCIE_MEM_BUS 0x08000000
+#define CONFIG_SYS_PCIE_MEM_PHYS_OFF 0x04000000
+#define CONFIG_SYS_PCIE_MEM_SIZE 0x80000000 /* 128M */
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP
+#define CONFIG_PCI_SCAN_SHOW
+#define CONFIG_CMD_PCI
+
+#define CONFIG_CMD_MEMINFO
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_SYS_MEMTEST_START 0x80000000
+#define CONFIG_SYS_MEMTEST_END 0x9fffffff
+
+#endif /* __LS1012ARDB_H__ */
projects / u-boot / commitdiff