Julius Werner [Wed, 7 Oct 2015 03:03:53 +0000 (20:03 -0700)]
Add support for LZ4 decompression algorithm
This patch adds support for LZ4-compressed FIT image contents. This
algorithm has a slightly worse compression ration than LZO while being
nearly twice as fast to decompress. When loading images from a fast
storage medium this usually results in a boot time win.
Sandbox-tested only since I don't have a U-Boot development system set
up right now. The code was imported unchanged from coreboot where it's
proven to work, though. I'm mostly interested in getting this recognized
by mkImage for use in a downstream project.
Signed-off-by: Julius Werner <jwerner@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
Overwriting an empty file not created by U-Boot did not work, and it
could even corrupt the FAT. Moreover, creating empty files or emptying
existing files allocated a cluster, which is not standard.
Fix this by always keeping empty files clusterless as specified by
Microsoft (the start cluster must be set to 0 in the directory entry in
that case), and by supporting overwriting such files.
set_contents() had uselessly split calls to set_cluster(). Merge these
calls, which removes some cases of set_cluster() being called with a
size of zero.
set_cluster() was using a temporary buffer without enforcing its
alignment for DMA and cache. Moreover, it did not check the alignment of
the passed buffer, which can come directly from applicative code or from
the user.
This could cause random data corruption, which has been observed on
i.MX25 writing to an SD card.
Fix this by only passing ARCH_DMA_MINALIGN-aligned buffers to
disk_write(), which requires the introduction of a buffer bouncing
mechanism for the misaligned buffers passed to set_cluster().
By the way, improve the handling of the corresponding return values from
disk_write():
- print them with debug() in case of error,
- consider that there is an error is disk_write() returns a smaller
block count than the requested one, not only if its return value is
negative.
After this change, set_cluster() and get_cluster() are almost
symmetrical.
Ryan Harkin [Fri, 9 Oct 2015 16:18:08 +0000 (17:18 +0100)]
vexpress64: juno: use /dev/sda2
This patch changes the default "root=" parameter to "/dev/sda2".
Many linux based distros use /dev/sda1 for their boot partition; this is
often not a rootfs that can be used by the "root=" parameter.
Linaro images use /dev/sda1 as a boot partition, although this of a
different nature to a distro image. Linaro uses /dev/sda2 for the rootfs
partition.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Ryan Harkin [Fri, 9 Oct 2015 16:18:07 +0000 (17:18 +0100)]
vexpress64: juno: add alternate kernel and device tree filenames
The latest Juno firmware stores the files in NOR flash as "norkern" for
kernel binary, "board.dtb" for the device tree binary.
The "old" firmware used the name "Image" for the kernel binary and
"juno" for the device tree binary.
Rather than just change the default U-Boot configuration to use the new
names, breaking users with the old firmware, attempt to load the default
filename first. If that fails, attempt to load the alternate filename.
I've echo'd that we are loading the alternate file to counter the
output from "afs load" shown if the first load attempt fails. For
example, I see output like this on my Juno board when it's configured
the with the "old" firmware:
image "norkern" not found in flash
Loading Image instead of norkern
loaded region 0 from 08500000 to 80000000, 00AB6318 bytes
image "board.dtb" not found in flash
Loading juno instead of board.dtb
loaded region 0 from 0A000000 to 83000000, 00003188 bytes
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Ryan Harkin [Fri, 9 Oct 2015 16:18:02 +0000 (17:18 +0100)]
vexpress64: fvp dram: add DRAM configuration
Create an additional FVP configuration to boot images pre-loaded into
DRAM.
Sometimes it's preferential to boot the model by loading the files
directly into DRAM via model parameters, rather than using
SemiHosting.
An example of model parmaters that are used to pre-load the files
into DRAM:
--data cluster0.cpu0=Image@0x80080000 \
--data cluster0.cpu0=fvp-base-gicv2-psci.dtb@0x83000000 \
--data cluster0.cpu0=uInitrd@0x84000000
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[trini: Update board/armltd/vexpress64/Kconfig logic] Signed-off-by: Tom Rini <trini@konsulko.com>
Ryan Harkin [Fri, 9 Oct 2015 16:18:00 +0000 (17:18 +0100)]
vexpress64: Kconfig: tidy up
The FVP and Juno settings were identical, but duplicated, so I removed
the duplication with this patch.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[trini: Adjust logic to keep if/endif in the file] Signed-off-by: Tom Rini <trini@konsulko.com>
Jagan Teki [Mon, 7 Sep 2015 20:08:50 +0000 (01:38 +0530)]
spi: zynq_spi: Fix to configure CPOL, CPHA mask
priv->mode is initialized when .set_speed triggers
with mode value, so checking mode for configuring
CPOL, CPHA using priv->mode is invalid hence use
mode from .set_speed argument, and at the end
priv->mode will initialized with mode.
This patch also replaces formatting string to use
speed instead of mode in .set_speed ops.
Jagan Teki [Mon, 7 Sep 2015 19:56:29 +0000 (01:26 +0530)]
spi: xilinx_spi: Fix to configure CPOL, CPHA mask
priv->mode is initialized when .set_speed triggers
with mode value, so checking mode for configuring
CPOL, CPHA using priv->mode is invalid hence use
mode from .set_speed argument, and at the end
priv->mode will initialized with mode.
This patch also replaces formatting string to use
speed instead of mode in .set_speed ops.
sunxi: Fix USB regulators in Linksprite_pcDuino_defconfig
The pcDuino1 board unconditionally provides 5V to USB host
receptacles. The pcDuino2 board has a voltage regulator,
controlled by the PD2 pin which is pulled-up by default
(so that the USB power is also enabled by default).
Not specifying pins for enabling USB power in the defconfig
means that the PH3 and PH6 pins are driven high by default.
The PH6 pin is available on the Arduino-compatible expansion
header and touching it is not nice (this may be even dangerous,
depending on what kind of role is assigned to this particular
pin by various Arduino shields).
This patch explicitly configures the USB VBUS pins to "",
which means that no pins should be touched. The patch has
been tested on a pcDuino2 board and USB still works.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
sunxi: Fix pcDuino reliability by downclocking DRAM to 360MHz
Linksprite_pcDuino_defconfig is a generic config for pcDuino1 and
pcDuino2 boards. The pcDuino2 board exists at least in two variants
(with DDR3 chips from HYNIX or NANYA). At least one pcDuino2 board
with HYNIX DDR3 fails the lima-memtester reliability test unless
the DRAM clock speed is reduced to 360MHz.
A detailed analysis report, generated by the a10-tpr3-scan tool with
the explanations why the DRAM is failing at 408MHz, is available at:
http://linux-sunxi.org/index.php?title=User:Ssvb/pcDuino2_with_HYNIX_DDR3_reliability_test&oldid=15152
http://web.archive.org/web/20151008190210/http://linux-sunxi.org/User:Ssvb/pcDuino2_with_HYNIX_DDR3_reliability_test
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Alexey Brodkin [Sun, 4 Oct 2015 13:10:26 +0000 (16:10 +0300)]
board: axs10x - cap max SDIO clock value to bus/2
It turned out with some boards (FPGA firmwares?) and cards combos
current clock settings doesn't work as expected leading to strange
card freezes or corrupted data being read from the card.
Especially this was seen with Transcend 2Gb cards shipped as a part of
ARC SDP:
----------------->8---------------
AXS# mmcinfo
Device: Synopsys Mobile storage
Manufacturer ID: 74
OEM: 4a60
Name: SDC
Tran Speed: 50000000
Rd Block Len: 512
SD version 3.0
High Capacity: No
Capacity: 1.8 GiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
AXS# fatload mmc 0
** Unrecognized filesystem type **
----------------->8---------------
With this change that problem is fixed.
Note "Tran Speed" above doesn't match clock value set in DW MMC.
It is max value for card's speed class.
Simon Glass [Sat, 3 Oct 2015 17:21:16 +0000 (11:21 -0600)]
sandbox: Correct operaion of 'reset' command
Currently 'reset' only works with the test device tree. When run without a
device tree, or with the normal device tree, the following error is
displayed:
Reset not supported on this platform
Fix the driver and the standard device tree to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org> Reported-by: Stephen Warren <swarren@nvidia.com> Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Simon Glass [Sat, 12 Sep 2015 14:45:19 +0000 (08:45 -0600)]
dm: core: Don't use pinctrl for the root device
Currently when driver model starts up it finds the root uclass and the
pinctrl uclass. This is because even the root node handles pinctrl
processing.
But this is not useful. The root node is not a real hardware device so
cannot require any particular pinmux settings. Also it means that the
memory leak tests fails, since they end up freeing more memory than
they allocate: the marker it set after the root device and pinctrl
uclass are allocated, and later once the pinctrl uclass is freed the memory
used by driver model is less than when the marker was set.
If a platform needs 'core' pin mulitplex settings it can do this with
a driver that is probed on start-up. It would be an abuse of the root node
to use this for pinctrl.
To avoid this problem, only process pinctrl settings for non-root nodes.
Sjoerd Simons [Sat, 3 Oct 2015 11:25:01 +0000 (13:25 +0200)]
rockchip: Reconfigure the malloc based to point to system memory
When malloc_base initially gets setup in the SPL it is based on the
current (early) stack pointer, which for rockchip is pointing into SRAM.
This means simple memory allocations happen in SRAM space, which is
somewhat unfortunate. Specifically a bounce buffer for the mmc allocated
in SRAM space seems to cause the mmc engine to stall/fail causing
timeouts and a failure to load the main u-boot image.
To resolve this, reconfigure the malloc_base to start at the relocated
stack pointer after DRAM has been setup.
For reference, things did work fine on rockchip before 596380db was
merged to fix memalign_simple due to a combination of rockchip SDRAM
starting at address 0 and the dw_mmc driver not checking errors from
bounce_buffer_start. As a result, when a bounce buffer needed to be
allocated mem_align simple would fail and return NULL. The mmc driver
ignored the error and happily continued with the bounce buffer address
being set to 0, which just happened to work fine..
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Simon Glass <sjg@chromium.org>
This device uses SDHCI driver, for eMMC and SD cards.
Trying bind the DW MMC driver with fdt node without all
required properties, causes printing an error.
mach-exynos: clock: restore calling dead exynos4_get_mmc_clk()
After rework of code by:
commit: d952796 Exynos5: Use clock_get_periph_rate generic API
function get_mmc_clk() always returns -1 for Exynos 4.
This was caused by omitting, that SDHCI driver for Exynos 4,
calls get_mmc_clk(), with mmc device number as argument,
instead of pinmux peripheral id, like DW MMC driver for Exynos 5.
By this commit, the code directly calls a proper function
to get mmc clock for Exynos 4, without checking the peripheral id.
fdtdec: fix parsing 'reg' property with zero value in '#size-cells'
After rework of lib/fdtdec.c by:
commit: 02464e3 fdt: add new fdt address parsing functions
the function fdtdec_get_addr() doesn't work as previous,
because the implementation assumes that properties '#address-cells'
and '#size-cells' are equal to 1, which can be not true sometimes.
The new API introduced fdtdec_get_addr_size_auto_parent() for the 'reg'
property parsing, but the implementation assumes, that #size-cells
can't be less than 1.
This causes that the following children's 'reg' property can't be reached:
Stephen Warren [Fri, 25 Sep 2015 16:11:41 +0000 (10:11 -0600)]
fdt: fix fdtdec_get_addr_size not to require any size cells
fdtdec_get_addr_size() may be used in two cases:
a) With sizep supplied, in which case both an address and a size are
parsed from DT. In this case, the DT property must be large enough to
contain both values.
b) With sizep NULL, in which case only an address is parsed from DT.
In this case, the DT property only need be large enough to contain this
address value. Commit 02464e386bb5 "fdt: add new fdt address parsing
functions" broke this relaxed checking, and required the DT property to
contain both an address and a size value in all cases.
Fix fdtdec_get_addr_size() to vary ns based on whether the size value
is being parsed from the DT or not. This is safe since the function only
parses the first entry in the property, so the overall value of (na + ns)
need not be accurate, since it is never used to step through the property
data to find other entries. Besides, this fixed behaviour essentially
matches the original behaviour before the patch this patch fixes. (The
original code validated that the property was exactly the length of
either na or (na + ns), whereas the current code only validates that the
property is at least that long. For non-failure cases, the two behaviours
are identical).
Cc: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Simon Glass <sjg@chromium.org> Cc: Thierry Reding <treding@nvidia.com> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Michal Suchanek <hramrach@gmail.com> Fixes: 02464e386bb5 ("fdt: add new fdt address parsing functions") Reported-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Tested-by: Przemyslaw Marczak <p.marczak@samsung.com> Acked-by: Simon Glass <sjg@chromium.org>
Hans de Goede [Tue, 29 Sep 2015 09:48:01 +0000 (11:48 +0200)]
sunxi: Add generic defconfigs for A23 Q8 tablets with 800x480 LCD
The 7" Q8 tablet enclosure is used for a ton of slightly different cheap
chinese tablets. There are some differences in which accelerometer /
wifi is used, but other then that these are all the same from a u-boot /
kernel pov.
When we get to adding accelerometer support the plan is to add some kind
of autodetection and mangle the dt accordingly (likely using the new quirks
mechanism).
For now this is a non issue as we do not yet have accelerometer
support, and in the future, some sort of auto-detect is the way to go
as we cannot expect users to exactly know what is inside their tablet.
The dts files this commit adds are identical to the ones submitted
to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Stephen Warren [Fri, 25 Sep 2015 16:44:08 +0000 (10:44 -0600)]
gpio: tegra: use named constants
In order to make it clear what the parameters to set_config() and
set_direction() mean, and similarly for the return values from the
respective get_*(), define named constants for these values.
Disassembly shows no diff in the generated code, except that the
order of the code in the branches of tegra_gpio_get_function() gets
modified without affecting behaviour.
Suggested-by: Tom Warren <twarren@nvidia.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Wed, 23 Sep 2015 18:34:01 +0000 (12:34 -0600)]
ARM: tegra: expand all SPL sizes to be consistent
The size allocation for SPL is increased in all cases to match the
already-expanded value used on Tegra124. This is both for general
consistency, and because the seaboard build trips over the limit already
when using one of the ARM compilers packaged with 14.04. For the record,
when building Seaboard:
arm-linux-gnueabi- SPL is too big by 0x36 bytes
arm-linux-gnueabihf- SPL fits by 0x2a bytes
arm-none-eabi- SPL fits by 0xa bytes
(Those figures are from builds with the expanded SPL size allocation,
relative to the non-expanded SPL size limit; they're better by about
6 bytes in the more constrained build.)
Fixes: ba521994229c ("tegra124: Expand SPL space by 8KB") Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Wed, 23 Sep 2015 18:13:00 +0000 (12:13 -0600)]
ARM: tegra: don't enable GPIOs until direction is set
Tegra's GPIO driver currently enables pins as GPIO as soon as they're
requested. This is not safe, since the desired direction and output value
are not yet known. This could cause a glitch on the output pins between
gpio_request() and gpio_direction_*(), depending on what values happen to
be in the GPIO controller's in/out and out-value registers vs. the final
desired configuration.
To solve this, defer enabling pins as GPIOs until some gpio_direction_*()
is invoked, and the desired configuration is explicitly programmed.
In theory this change could cause regressions, if code exists that claims
a GPIO, never explicitly sets a direction, and then gets/sets the GPIO
value based on that assumption. However, I've read through all the Tegra-
related board files and device drivers that touch GPIOs and I do not see
such buggy code anywhere.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Wed, 23 Sep 2015 18:12:59 +0000 (12:12 -0600)]
ARM: tegra: fix GPIO init table programming
Tegra's gpio_config_table() currently uses common GPIO APIs. These used
to work without requesting the GPIO, but since commit 2fccd2d96bad "tegra:
Convert tegra GPIO driver to use driver model" no longer do so. This
prevents any of the GPIO initialization table from being applied to HW.
Fix gpio_config_table() to directly program the HW to solve this.
Fixes: 2fccd2d96bad ("tegra: Convert tegra GPIO driver to use driver model") Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Mon, 21 Sep 2015 22:45:22 +0000 (16:45 -0600)]
ARM: tegra: p2371-2180: import latest pinmux
In order to avoid any assumptions about any device connected to
P2371-2180's expansion connector, the latest pinmux spreadsheet
configures all muxable pins on that connector to be GPIO inputs, with
on-chip pulls where appropriate.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
The driver assumed that I2C1 and I2C2 were always enabled,
and if they were not, then an asynchronous abort was (silently)
raised, to be caught much later on in the Linux kernel.
Fix this by making I2C1 and I2C2 optional just like I2C3 and I2C4
are.
To make the change binary-invariant, declare I2C1 and I2C2 in
every include/configs/ file which defines CONFIG_SYS_I2C_MXC.
Also, while updating README about CONFIG_SYS_I2C_MXC_I2C1 and
CONFIG_SYS_I2C_MXC_I2C2, add missing descriptions for I2C4 speed
(CONFIG_SYS_MXC_I2C4_SPEED) and slave (CONFIG_SYS_MXC_I2C4_SLAVE)
config options.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
The VF610 DDRMC driver code contains settings which are
board-specific. Move these out to boards so that new boards
can define their own without having to modify the driver.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Peng Fan [Sun, 6 Sep 2015 09:15:47 +0000 (17:15 +0800)]
imx: mx6: correct enable_fec_anatop_clock
We should follow 'read->set/clr bit->write' flow for enable_fec_anatop_clock,
otherwise we may overridden configuration before enable_fec_anatop_clock.
Stefan Roese [Tue, 29 Sep 2015 07:19:59 +0000 (09:19 +0200)]
tools: kwboot: Add support for UART boot mode patching for Armada XP/38x
Currently, kwboot only allows dynamic UART boot mode patching for SoCs
with header version 0 (Orion, Kirkwood). This patch now enables this "-p"
feature also for SoCs with header version 1 (Armada XP / 38x etc). With
this its possible now to use the UART boot mode without on images that
are generated for other boot devices, like SPI. So no need to change
BOOT_FROM to "uart" for UART xmodem booting any more.
Signed-off-by: Stefan Roese <sr@denx.de> Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Dirk Eibach <eibach@gdsys.de>
Stefan Roese [Thu, 3 Sep 2015 10:47:07 +0000 (12:47 +0200)]
arm: mvebu: timer.c: Explicitly move "init_done" var to data section
As reported by Simon Guinot, commit ade741b3
"arm: mvebu: Call timer_init early before PHY and DDR init" breaks
Kirkwood platforms. As the static variable "init_done" is not
available at that early boot time. This patch moves it to explicitly
to the data section, making it available at that time.
Signed-off-by: Stefan Roese <sr@denx.de> Reported-by: Simon Guinot <simon.guinot@sequanux.org> Cc: Luka Perkov <luka.perkov@sartura.hr> Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Stefan Roese [Mon, 24 Aug 2015 09:03:50 +0000 (11:03 +0200)]
arm: mvebu: Fix internal register config on A38x
Currently booting on A38x is broken. As the current code tries to detect
the SoC family to disable the MMU for the A38x at runtime. But before the
internal registers are switched to the new location (0xf100.0000), this
runtime detection does not work. As all macros / defines are already
assigned to the new location at 0xf100.0000. But the registers are sill
mapped to the default location at 0xd000.0000.
This patch now makes sure, no such runtime detection is used before
the internal registers are configured to the new location. After this,
the remaining cache cleanup is executed.
Signed-off-by: Stefan Roese <sr@denx.de> Reported-by: Kevin Smith <kevin.smith@elecsyscorp.com> Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch introduces CONFIG_NETCONSOLE as an option to the
Kconfig system.
Joe Hershberger pointed out that it may not be entirely free of
problems, as many boards predating the driver model define this
symbol directly via include files. In case they're not properly
migrated, their NetConsole might 'vanish' if they start to use
CONFIG_NET or CONFIG_NETDEVICES.
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
net: avoid eth_unregister() call when function is unavailable
CONFIG_NETCONSOLE causes common/bootm.c to call eth_unregister()
for network device shutdown. However, with CONFIG_DM_ETH this
function is no longer defined.
This is a workaround to avoid the call in that case, and solely
rely on eth_halt(). In case this is insufficient, a proper way
to unregister / remove network devices needs to be implemented.
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
net: expose eth_is_active() function to test network device state
The previous eth_device struct returned by eth_get_dev() allowed
code to directly query the state member field. However, with
CONFIG_DM_ETH this data gets encapsulated (i.e. private), and
eth_get_dev() returns a udevice struct 'abstraction' instead.
This breaks legacy code relying on the former behaviour - e.g.
netconsole.
(see http://lists.denx.de/pipermail/u-boot/2015-June/216528.html)
The patch introduces a method to retrieve the ethernet device
state in a 'clean' and uniform way, supporting both legacy code
and driver model. The new function eth_is_active() accepts a
device struct pointer and tests it for ETH_STATE_ACTIVE.
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Mugunthan V N [Thu, 3 Sep 2015 10:20:21 +0000 (15:50 +0530)]
net: phy: on phy device create do not initialize link to 1
Currently when phy device is created the link variable is
initialized to 1 which denoted phy link is already up. On a power
reset there is no issue as phy status register link status will
not be set, so phy auto negotiate will be started. But when a cpu
reset is issued (ex: dra72x-evm) phy's link status bit is already
set which leads to assume that link is already setup in
genphy_update_link() initial check which results in ehternet not
working. So do not assume that link is already up and on phy
device create set link to zero. This is verified on dra72x-evm.
Reported-by: Franklin S Cooper Jr <fcooper@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Hans de Goede [Sun, 20 Sep 2015 23:46:49 +0000 (19:46 -0400)]
sunxi: Add generic defconfigs for A33 Q8 tablets with 1024x600 / 800x480 LCD
The 7" Q8 tablet enclosure is used for a ton of slightly different cheap
chinese tablets. There are some differences in which accelerometer /
wifi is used, but other then that these are all the same from a u-boot /
kernel pov.
When we get to adding accelerometer support the plan is to add some kind
of autodetection and mangle the dt accordingly (likely using the new quirks
mechanism).
For now this is a non issue as we do not yet have accelerometer
support, and in the future, some sort of auto-detect is the way to go
as we cannot expect users to exactly know what is inside their tablet.
The dts[i] files this commit adds are identical to the ones submitted
to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Wed, 23 Sep 2015 14:13:10 +0000 (16:13 +0200)]
sunxi: mmc: Fix clk-delay settings
In recent allwinner kernel sources the mmc/sdio clk-delay settings have
been slightly tweaked, and for sun9i they are completely different then
what we are using.
This commit brings us in sync with what allwinner does, fixing problems
accessing sdcards on some A33 devices (and likely others).
For pre sun9i hardware this makes the following changes:
-At 400Khz change the sample delay from 7 to 0 (first introduced in A31 sdk)
-At 50 Mhz change the sample delay from 5 to 4 (first introduced in A23 sdk)
-Above 50 MHz change the out delay from 2 to 1 (first introduced in A20 sdk)
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
This patch makes use of the previous changes to add a new "fel" boot
target for sunxi boards.
When booting via FEL, it's often desirable to work around the absence
of other (usable) boot devices - or to be able to override them,
deviating from the standard boot sequence. To achieve this, the "fel"
boot target gets the highest priority, but won't actually do anything
unless certain criteria are met.
The "bootcmd_fel" implementation proposed here first tests if an actual
FEL boot takes place (using the "fel_booted" env var), and secondly
checks that "fel_scriptaddr" was set (originating from the 'loader',
i.e. the sunxi-tools fel utility). If both checks pass, then it will
try to execute the boot script (boot.scr) at the given address. In case
of an error (e.g. an invalid image), the source command might return
"false", causing "distro_bootcmd" to proceed with the next boot target.
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de> Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
sunxi: retrieve FEL-provided values to environment variables
This patch extends the misc_init_r() function on sunxi boards
to test for the presence of a suitable "sunxi" SPL header. If
found, and the loader ("fel" utility) provided a non-zero value
for the boot.scr address, then the corresponding environment
variable fel_scriptaddr gets set.
misc_init_r() also sets (or clears) the "fel_booted" variable depending
on the active boot device, using the same logic as spl_boot_device().
The goal is to provide sufficient information (within the U-Boot
environment) to make intelligent decisions on how to continue the boot
process, allowing specific customizations for the "FEL boot" case.
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
sunxi: (mksunxiboot) signature to indicate "sunxi" SPL variant
This patch follows up on a discussion of ways to improve support
for the sunxi FEL ("USB boot") mechanism, especially with regard
to boot scripts, see:
https://groups.google.com/d/msg/linux-sunxi/wBEGUoLNRro/rHGq6nSYCQAJ
The idea is to convert the (currently unused) "pad" bytes in the
SPL header into an area where data can be passed to U-Boot. To
do this safely, we have to make sure that we're actually using
our "sunxi" flavor of the SPL, and not the Allwinner boot0.
The modified mksunxiboot introduces a special signature to the
SPL header in place of the "pub_head_size" field. This can be
used to reliably distinguish between compatible versions of sunxi
SPL and anything else (older variants or Allwinner's boot0).
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de> Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
sunxi: move SPL-related definitions to platform-specific include
The sunxi platform currently doesn't seem to make any use of the
asm/arch-sunxi/spl.h file. This patch moves some declarations from
tools/mksunxiboot.c into it.
This enables us to reuse those definitions when extending the
sunxi board code (boards/sunxi/boards.c).
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Sun, 13 Sep 2015 15:29:33 +0000 (17:29 +0200)]
sunxi: sunxi-common.h cleanup
Move some #define-s around from one #ifdef block to another to
reduce the number of #ifdef blocks (note this causes no functional
changes even though the conditions are not always exactly the same)
and move generic #include statements to the top.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 12 Sep 2015 10:42:50 +0000 (12:42 +0200)]
sunxi: Rename A10s-Wobo-i5_defconfig to Wobo_i5_defconfig
We only prefix the board defconfig name with the SoC if the SoC is part
of the official board-name, such as with Olimex OLinuxIno boards, for the
Wobo i5 this is not the case so remove the A10s prefix from the defconfig
filename.
Also fix the double listing of A10s-OLinuXino-M_defconfig in MAINTAINERS
which the original Wobo i5 addition commit introduced.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Simon Glass [Tue, 8 Sep 2015 23:52:45 +0000 (17:52 -0600)]
x86: chromebook_link: Expand early malloc() memory
Now that PCI bridges are probed before relocation we need additional memory.
Each PCI bridge takes 240 bytes at present since it uses the same uclass as
the PCI controller. Probably we should split this out so that bridges have
their own uclass.
Expand the memory on link so that it works correctly.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For some workloads - dfu test @ Odroid XU3 (sending 8MiB file) -
and SD cards (e.g. MicroSD Kingston 4GiB, Adata 4GiB)
the default timeout is to short.
The new value - 4 minutes (240 seconds) - is the same as the one used in
Linux kernel driver. Such fix should be good enough until we come up
with better fix for this issue.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marex@denx.de> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Tom Rini <trini@konsulko.com> Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
tools: gen_eth_addr: add getpid() to time(0) to avoid duplicated seed
As 'time(0) | getpid()' will have a lot of duplicated value. It is not a
expected behavior. We expect different value for the seed when when run
it in many times.
So this patch will left shift the getpid() and add to time(0). That
avoid duplicated value.
Test command is like:
% RUN=0; while [ $RUN -lt 10000 ]; do
tools/gen_eth_addr; RUN=$(($RUN+1)); done | sort | uniq | wc -l
10000
This patch is incorporated with suggestions made by Wolfgang Denk and Andreas
Bießmann. Thanks them a lot.
Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Andreas Bießmann <andreas.devel@googlemail.com> Acked-by: Wolfgang Denk <wd@denx.de> Tested-by: Wolfgang Denk <wd@denx.de>
Peter Griffin [Thu, 10 Sep 2015 20:55:17 +0000 (21:55 +0100)]
ARM: hikey: hi6220: Migrate over to DM_SERIAL and use UART3 by default.
Use DM for the pl01x serial driver on hikey. Also allow UART0 or
UART3 to be chosen via Kconfig.
By default we now output to UART3 as the latest version of ATF outputs
to this UART. Also UART3 comes out on the LS connector, as opposed to
UART0 which goes to a unpopulated header.
As part of this change we also enable CONFIG_BOARD_EARLY_INIT_F and
call the pinmux configuration code for the UART. Before we were
relying on ATF having already configured the pin configuration.
NB: Upstream Linux kernel doesn't yet support UART3, so serial console
will still be output on UART0 when booting a upstream kernel.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Peter Griffin [Thu, 10 Sep 2015 20:55:15 +0000 (21:55 +0100)]
ARM: hikey: Remove resetting gd->flags in board_init()
This causes exceptions and other strange behaviour
when enabling CONFIG_SYS_MALLOC_F_LEN which is required to
migrate the serial driver over to DM_SERIAL.
As GD_FLG_FULL_MALLOC_INIT flag gets reset, after relocation
we don't end up using the full malloc which ultimately ends up
causing a synchronus abort.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
projects / u-boot / log