usb: dwc3: dwc3-omap: Use the clear register inorder to clear the interrupts
Writing "0x00" to the USBOTGSS_IRQENABLE_SET_MISC and
USBOTGSS_IRQENABLE_SET_0 doesn't disable the interrupts. Used
USBOTGSS_IRQENABLE_CLR_MISC and USBOTGSS_IRQENABLE_CLR_0 instead.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Acked-by: Marek Vasut <marex@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
Andreas Bießmann [Fri, 28 Aug 2015 08:29:55 +0000 (10:29 +0200)]
Makefile: fix SOURCE_DATE_EPOCH for *BSD host
The SOURCE_DATE_EPOCH mechanism for reproducible builds require some date(1)
with -d switch to print the relevant date and time strings of another point of
time.
In other words it requires some date(1) that behaves like the GNU date(1) [1].
The BSD date(1) [2] on the other hand has the same switch but with a different
meaning.
Respect this and check the date(1) abilities before usage, error on non
working version. Use the well known pre- and suffixes for the GNU variant of
a tool on *BSD hosts to search for a working date(1) version.
Andreas Bießmann [Tue, 25 Aug 2015 07:48:16 +0000 (09:48 +0200)]
picosam9g45: adopt CONFIG_SYS_PROMPT
Commit 181bd9dc61d2da88b78f1c1138a685dae39354d6 introduced Kconfig selection
for SYS_PROMPT. When applying the new picosam9g45 board this change slipped
through, adopt it.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
omap-common: SYS_BOOT fallback logic correction and support for more devices
The SYS_BOOT-based fallback shouldn't only check for one of the conditions of
use and then let the switch/case handle each boot device without enforcing the
conditions for each type of boot device again.
For instance, this behaviour would trigger the fallback for UART when
BOOT_DEVICE_UART is defined, CONFIG_SPL_YMODEM_SUPPORT is enabled (which should
be a show-stopper) and e.g. BOOT_DEVICE_USB is enabled and not
CONFIG_SPL_USB_SUPPORT.
Separating the logic for USB and UART solves this.
In addition, this adds support for more peripheral devices (USBETH and CPGMAC)
to the fallback mechanism. Note that the USBETH boot device should always be
different from the USB boot device (each should match a different bootrom
handoff case).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Hannes Schmelzer <oe5hpm@oevsv.at> Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Marcel Ziswiler [Tue, 18 Aug 2015 11:06:37 +0000 (13:06 +0200)]
mtd/nand/ubi: assortment of alignment fixes
Various U-Boot adoptions/extensions to MTD/NAND/UBI did not take buffer
alignment into account which led to failures of the following form:
ERROR: v7_dcache_inval_range - start address is not aligned - 0x1f7f0108
ERROR: v7_dcache_inval_range - stop address is not aligned - 0x1f7f1108
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Scott Wood <scottwood@freescale.com>
[trini: Add __UBOOT__ hunk to lib/zlib/zutil.c due to malloc.h in common.h] Signed-off-by: Tom Rini <trini@konsulko.com>
Stefan Roese [Tue, 18 Aug 2015 07:27:20 +0000 (09:27 +0200)]
arm: spear: Some changes / updates to the x600 config header
This patch brings the following changes to the x600 board support:
- Add USB EHCI support
- Add VFAT support for USB key file access
- Increase malloc size (for UBI / UBIFS usage)
- Enable Thumb mode to save some image space
- Remove unreferenced CONFIG_STACKSIZE
- Remove unreferenced CONFIG_SPL_NO_PRINTF
Booting SPEAr600 eval board doesn't work with current mainline U-Boot. With
this patch the low-vector bit is left to '0'. Resulting in the common
relocation of the vectors to 0 (SDRAM) to work correctly.
Lokesh Vutla [Mon, 17 Aug 2015 14:28:34 +0000 (19:58 +0530)]
ARM: k2l: Fix device speeds
ARM supported speeds and init value of core_pll for SDP1200
are programmed wrong as part for the device speed cleanups.
Fixing it here.
Thanks to "Vitaly Andrianov <vitalya@ti.com>" for bisecting this issue
Fixes: c37ed9f11b61 ("ARM: keystone2: Fix dev and arm speed detection") Tested-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 17 Aug 2015 14:24:51 +0000 (19:54 +0530)]
ARM: keystone2: Build MLO by default
MLO(NAND/MMC boot image), is used for all the ks2 platforms.
Enabling it in config.mk so that these images will be automatically
built upon calling make. u-boot-spi.gph is already the build target,
so not including here.
Lokesh Vutla [Mon, 17 Aug 2015 14:24:50 +0000 (19:54 +0530)]
ARM: keystone2: Rename u-boot-nand.gph to MLO
NAND boot mode, ROM expects an image with a gp header in the
beginning and an 8bytes filled with zeros at the end. The same is
true for SD boot on K2G platforms but the file name should be MLO.
Renaming u-boot-nand.gph to MLO, so that same image can be used for
NAND and SD boots. And also not including all the u-boot only images
under CONFIG_SPL_BUILD.
Nishanth Menon [Mon, 17 Aug 2015 14:24:49 +0000 (19:54 +0530)]
ARM: keystone2: move the custom build rules out to keystone specific makefile
Keystone has build rules introduced by commit ef509b9063fb7 ("k2hk: add
support for k2hk SOC and EVM") and commit 0e7f2dbac6ead ("keystone: add
support for NAND gpheader image").
These are not reused by other platforms for the build, hence there is no
clear benefit is maintaining them in the generic makefile as a build
target. move these to the keystone specific make option
Original idea of using config.mk by Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Mon, 17 Aug 2015 14:24:48 +0000 (19:54 +0530)]
ARM: keystone2: configs: Move SP to end of u-boot section
Currently u-boot stack is defined at the beginning of MSMC RAM.
This is a problem for uart boot mode as ROM downloads directly to
starting of MSMC RAM.
Fixing it by moving stack to the end of u-boot section and shifting
SYS_TEXT_BASE to the start of MSMC RAM.
Updated division of MSMC RAM is shown below:
-----------------------------------------
| | | |
| U-Boot text |U-Boot | SPL text |
| download | Stack | Download + |
| | | SPL_BSS + |
| | | SPL_STACK |
-----------------------------------------
[1] [2] [3] [4]
[1] SYS_TEXT_BASE (Start of MSMC RAM)
[2] SPL_TEXT_BASE - GBL_DATA_SIZE
[3] SPL_TEXT_BASE
[4] END of SPL
[1] + [2] is at least 1M on all platforms, so no chance of overlap.
Hans de Goede [Sat, 15 Aug 2015 18:05:01 +0000 (20:05 +0200)]
env_mmc: Properly prefix mmc errors with '!'
The set_default_env() function from env_common.c expects either
a fully formatted error msg, e.g.: "## Resetting to default environment\n"
or an error msg prefixed with an !, in which case it will format it.
Fix the init_mmc_for_env() error messages to be prefixed with a !
this changes the bootup-log on sunxi when no mmc card is found from:
MMC: SUNXI SD/MMC: 0
No MMC card foundIn: serial
Out: serial
To:
MMC: SUNXI SD/MMC: 0
*** Warning - No MMC card found, using default environment
In: serial
Out: serial
Which clearly is how things should look.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Ulf Magnusson [Thu, 13 Aug 2015 17:55:40 +0000 (19:55 +0200)]
kconfiglib: update to the latest version
Corresponds to ba71a0e (Fix _parse_block() 'parent' documentation re.
ifs.) from upstream, just adding the SPDX tag.
Has performance improvements, code cleanup, Python 3 support, and various
small fixes, including the following:
- Unset user values when loading a zero-byte .config. (5e54e2c)
- Ignore indented .config assignments. (f8a7510)
- Do not require $srctree to be set for non-kernel projects. (d56e9c1)
- Report correct locations in the presence of continuation lines.
(0cebc87) Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Nishanth Menon [Thu, 13 Aug 2015 14:51:00 +0000 (09:51 -0500)]
ARM: DRA74-evm: Use SMA_1 spare register to workaround DP83865 phy on SR2.0
DP83865 ethernet phy used on DRA74x-evm is quirky and the datasheet
provided IODELAY values for standard RGMII phys do not work.
Silicon Revision(SR) 2.0 provides an alternative bit configuration
that allows us to do a "gross adjustment" to launch the data off a
different internal clock edge. Manual IO Delay overrides are still
necessary to fine tune the clock-to-data delays. This is a necessary
workaround for the quirky ethernet Phy we have on the platform.
NOTE: SMA registers are spare "kitchen sink" registers that does
contain bits for other workaround as necessary as well. Hence the
control for the same is introduced in a generic SoC specific, board
generic location.
Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Nishanth Menon [Thu, 13 Aug 2015 14:50:59 +0000 (09:50 -0500)]
ARM: DRA74-evm: Add iodelay values for SR2.0
Silicon revision 2.0 has new signal routing hence has an updated set of
iodelay parameters to be used. Update the configuration for the same.
Padmux remains the same.
Based on data from VayuES2_EVM_Base_Config-20150807.
NOTE: With respect to the RGMII values, the Manual IODelay values
are used for the fine adjusments needed to meet the tight RGMII
specification.
Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Nishanth Menon [Thu, 13 Aug 2015 14:50:58 +0000 (09:50 -0500)]
ARM: DRA7: Add detection of ES2.0
Add support for detection of ES2.0 version of DRA7 family of
processors. ES2.0 is an incremental revision with various fixes
including the following:
- reset logic fixes
- few assymetric aging logic fixes
- MMC clock rate fixes
- Ethernet speed fixes
- edma fixes for mcasp
[ravibabu@ti.com: posted internal for an older bootloader] Signed-off-by: Ravi Babu <ravibabu@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Acked-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Chris Packham [Thu, 13 Aug 2015 06:08:27 +0000 (18:08 +1200)]
Makefile: Use correct timezone for U_BOOT_TZ
When building with SOURCE_DATE_EPOCH the timezone is in UTC. When
building normally the timezone is taken from the build machine's locale
setting.
Signed-off-by: Chris Packham <judge.packham@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Paul Kocialkowski <contact@paulk.fr> Tested-by: Andreas Bießmann <andreas.devel@googlemail.com>
Suriyan Ramasami [Tue, 18 Aug 2015 16:25:33 +0000 (09:25 -0700)]
lib/display_options: Fix print_freq
Build without CONFIG_SPL_SERIAL_SUPPORT does not print the cpu freq.
I have seen this in the odroid U3 board, where on boot one sees this:
CPU: Exynos4412 @ GHz
instead of:
CPU: Exynos4412 @ 1 GHz
I am assuming that this change was done to get rid of compiler
warnings related to unused variables when building with
CONFIG_SPL_SERIAL_SUPPORT not being defined in an SPL build.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Heiko Schocher <hs@denx.de> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Thierry Reding [Thu, 20 Aug 2015 09:45:43 +0000 (11:45 +0200)]
image: Fix loop condition to avoid warning
GCC 5.1 starts warning for comparisons such as !a > 0, assuming that the
negation was meant to apply to the whole expression rather than just the
left operand.
Indeed the comparison in the FIT loadable code is confusingly written,
though it does end up doing the right thing. Rewrite the condition to be
more explicit, that is, iterate over strings until they're exhausted.
Signed-off-by: Thierry Reding <treding@nvidia.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Mon, 24 Aug 2015 08:14:03 +0000 (01:14 -0700)]
x86: crownbay: Support Topcliff integrated pci uart devices with driver model
In order to make a pci uart device node to be properly bound to its
driver, we need make sure its parent node has a compatible string
which matches a driver that scans all of its child device nodes in
the device tree.
Change all pci bridge nodes under root pci node to use "pci-bridge"
compatible driver, as well as corresponding <reg> properties to
indicate its devfn. At last, adding "u-boot,dm-pre-reloc" to each
of these nodes for driver model to initialize them before relocation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Mon, 24 Aug 2015 08:14:02 +0000 (01:14 -0700)]
dm: core: Fix code reentrancy issue in device_probe_child()
The device might have already been probed during the call to
device_probe() on its parent device (e.g. PCI bridge devices).
In its parent device's probe routine, it might probe all of
its child devices via device_probe() thus the codes reenter
device_probe_child(). To support code reentrancy, test these
allocated memory against NULL to avoid memory leak, and return
to the caller if dev->flags has DM_FLAG_ACTIVATED set after
device_probe() returns, so that we don't mess up the device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
So far we only enabled one legacy serial port on the SMSC LPC47m
superio chipset on Intel Crown Bay board. As the board also has
dual PS/2 ports routed out, enable the keyboard controller which
is i8042 compatible so that we can use PS/2 keyboard and mouse.
In order to make PS/2 keyboard work with the VGA console, remove
CONFIG_VGA_AS_SINGLE_DEVICE. To boot Linux kernel with PIC mode
using PIRQ routing table, adjust the mask in the device tree to
reserve irq12 which is used by PS/2 mouse.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Mon, 24 Aug 2015 08:00:07 +0000 (01:00 -0700)]
video: cfb_console: Allow VGA device to work without i8042 keyboard
So far if CONFIG_VGA_AS_SINGLE_DEVICE is not defined, the VGA device
will try to initialize a keyboard device (for x86, it is i8042). But
if i8042 controller initialization fails (eg: there is no keyboard
connected to the PS/2 port), drv_video_init() just simply returns.
This kills the opportunity of using a usb keyboard later with the vga
console, as the vga initialization part is actually ok, only keyboard
part fails. Change the code logic to allow this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
Bin Meng [Mon, 24 Aug 2015 08:00:06 +0000 (01:00 -0700)]
x86: i8042: Correctly initialize the controller
The existing i8042 keyboard controller driver has some issues.
First of all, it does not issue a self-test command (0xaa) to the
controller at the very beginning. Without this, the controller
does not respond to any command at all. Secondly, it initializes
the configuration byte register to turn on the keyboard's interrupt,
as U-Boot does not normally allow interrupts to be processed.
Finally, at the end of the initialization routine, it wrongly
sets the controller to disable all interfaces including both
keyboard and mouse.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Mon, 24 Aug 2015 08:00:05 +0000 (01:00 -0700)]
x86: i8042: Clean up the driver per coding convention
- Rename CamelCase variables to conform U-Boot coding convention
- Rename wait_until_kbd_output_full() to kbd_output_full()
- Change to use macros for i8042 command and control register bits
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 22 Aug 2015 21:58:59 +0000 (15:58 -0600)]
x86: gpio: Tidy up gpio_ich6_get_base() and callers
This function can return an error. Correct the detection of this error so
that it works even with large 32-bit addresses.
The return value is set up for returning an I/O address but the function is
also used to return a memory-mapped address. Adjust the return code to make
this work.
Saket Sinha [Sat, 22 Aug 2015 06:50:56 +0000 (12:20 +0530)]
x86: Add ACPI table support to QEMU
This patch mainly adds ACPI support to QEMU.
Verified by booting Linux kernel on QEMU Q35.
Signed-off-by: Saket Sinha <saket.sinha89@gmail.com>
Minor whitespace fixes and dropped mention of i440FX in commit message: Signed-off-by: Simon Glass <sjg@chromium.org>
Saket Sinha [Sat, 22 Aug 2015 06:50:55 +0000 (12:20 +0530)]
x86: Generate a valid ACPI table
Implement write_acpi_table() to create a minimal working ACPI table.
This includes writing FACS, XSDT, RSDP, FADT, MCFG, MADT, DSDT & SSDT
ACPI table entries.
Use a Kconfig option GENERATE_ACPI_TABLE to tell U-Boot whether we need
actually write the APCI table just like we did for PIRQ routing, MP table
and SFI tables. With ACPI table existence, linux kernel gets control of
power management, thermal management, configuration management and
monitoring in hardware.
Signed-off-by: Saket Sinha <saket.sinha89@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tidied up whitespace and aligned some tabs: Signed-off-by: Simon Glass <sjg@chromium.org>
Bin Meng [Fri, 21 Aug 2015 07:18:51 +0000 (00:18 -0700)]
x86: superio: Add keyboard controller support to smsc_lpc47m driver
Add an api to enable and configure the integrated keyboard controller
on SMSC LPC47m superio chipset. It also adds several macros to help
future extension.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Thu, 20 Aug 2015 13:40:23 +0000 (06:40 -0700)]
x86: fsp: Call fsp_init_phase_pci() in pci_uclass_post_probe()
Per Intel FSP specification, we should call FSP notify API to
inform FSP that PCI enumeration has been done so that FSP will
do any necessary initialization as required by the chipset's
BIOS Writer's Guide (BWG).
Unfortunately we have to put this call here as with driver model,
the enumeration is all done on a lazy basis as needed, so until
something is touched on PCI it won't happen.
Note we only call this after U-Boot is relocated and root bus has
finished probing.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Thu, 20 Aug 2015 13:40:22 +0000 (06:40 -0700)]
x86: baytrail: Remove the fsp_init_phase_pci() call
It turns out that calling fsp_init_phase_pci() in arch_misc_init()
is subject to break pci device drivers as with driver model, when
the bus enumeration happens is not deterministic.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Thu, 20 Aug 2015 13:40:21 +0000 (06:40 -0700)]
x86: queensbay: Move unprotect_spi_flash() to arch_misc_init()
With dm pci conversion, pci config read/write in unprotect_spi_flash()
silently fails as at that time dm pci is not ready and bus enumeration
is not done yet. Actually we don't need to do this in that early phase,
hence we delay this call to arch_misc_init().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Thu, 20 Aug 2015 13:40:20 +0000 (06:40 -0700)]
x86: fsp: Add comments about U-Boot entering start.S twice
Add some comments in start.S for the fact that with FSP U-Boot
actually enters the code twice. Also change to use fsp_init()
and fsp_continue for accuracy.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Thu, 20 Aug 2015 13:40:19 +0000 (06:40 -0700)]
x86: fsp: Enlarge the size of malloc() pool before relocation
After fsp_init() returns, the stack has already been switched to a
place within system memory as defined by CONFIG_FSP_TEMP_RAM_ADDR.
Enlarge the size of malloc() pool before relocation since we have
plenty of memory now.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Thu, 20 Aug 2015 13:40:17 +0000 (06:40 -0700)]
dm: pci: Support selected device/driver binding before relocation
On some platforms pci devices behind bridge need to be probed (eg:
a pci uart on recent x86 chipset) before relocation. But we won't
bind all devices found during the enumeration. Only devices whose
driver with DM_FLAG_PRE_RELOC set will be bound. Any other generic
devices except bridges won't be bound.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 15 Aug 2015 20:37:54 +0000 (14:37 -0600)]
x86: ifdtool: Drop microcode from the device tree when collating
When ifdtool collates the microcode into one place it effectively creates
a copy of the 'data' properties in the device tree microcode nodes. This
is wasteful since we now have two copies of the microcode in the ROM.
To avoid this, remove the microcode data from the device tree and shrink it
down. This means that there is only one copy and the overall ROM space used
by the microcode does not increase.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 15 Aug 2015 20:37:53 +0000 (14:37 -0600)]
x86: ifdtool: Support collating microcode into one place
The Intel Firmware Support Package (FSP) requires that microcode be provided
very early before the device tree can be scanned. We already support adding
a pointer to the microcode data in a place where early init code can access.
However this just points into the device tree and can only point to a single
lot of microcode. For boards which may have different CPU types we must
support multiple microcodes and pass all of them to the FSP in one place.
Enhance ifdtool to scan all the microcode, place it together in the ROM and
update the microcode pointer to point there. This allows us to pass multiple
microcode blocks to the FSP using its existing API.
Enable the flag in the Makefile so that this feature is used by default for
all boards.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 15 Aug 2015 20:37:51 +0000 (14:37 -0600)]
x86: ifdtool: Check that U-Boot does not overlap other regions
Since U-Boot and its device tree can grow we should check that it does not
overlap the regions above it. Track the ROM offset that U-Boot reaches and
check that other regions (written after U-Boot) do not interfere.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Bin Meng [Sat, 15 Aug 2015 20:37:50 +0000 (14:37 -0600)]
x86: baytrail: Support multiple microcode copies
Intel FSP has the capability to walk through the microcode blocks
which are passed as the TempRamInit() parameter from U-Boot and
finds the most appropriate microcode which is suitable for the cpu
on which it is running. Now we've seen several steppings for Intel
BayTrail series processors, adding those microcodes to the Intel
BayleyBay and MinnowMax board device tree files.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Simon Glass <sjg@chromium.org>
Bin Meng [Thu, 13 Aug 2015 07:29:17 +0000 (00:29 -0700)]
x86: Set up video framebuffer for coreboot before loading kernel
Currenlty we only set up video framebuffer when VIDEO_VESA driver is
used. With coreboot, VIDEO_COREBOOT driver is used instead. Since we
already saved VESA mode in the VIDEO_COREBOOT driver, now we can also
set up video framebuffer for coreboot before loading Linux kernel.
Bin Meng [Thu, 13 Aug 2015 07:29:16 +0000 (00:29 -0700)]
video: coreboot: Save VESA mode for future use
When booting as a coreboot payload, the framebuffer details are
passed from coreboot via configuration tables. We save these
information into vesa_mode_info structure for future use.
Bin Meng [Thu, 13 Aug 2015 07:29:08 +0000 (00:29 -0700)]
x86: coreboot: Increase memrange entry number to 32
Increase lib_sysinfo memrange entry number to 32 to sync with coreboot.
This allows a complete E820 table to be reported to the kernel, as on
some platforms (eg: Bayley Bay) having only 16 entires does not cover
all the memory ranges.
Bin Meng [Thu, 13 Aug 2015 07:29:07 +0000 (00:29 -0700)]
x86: doc: Update coreboot payload entry point address
With recent EFI support, the entry point address of coreboot payload
was changed. Now we update the address to use _x86boot_start, which
is the same one for EFI.
Bin Meng [Wed, 26 Aug 2015 13:17:27 +0000 (06:17 -0700)]
net: e1000: Fix build warnings for 32-bit
commit 6497e37 "net: e1000: Support 64-bit physical address" causes
compiler warnings on 32-bit U-Boot build below.
drivers/net/e1000.c: In function 'e1000_configure_tx':
drivers/net/e1000.c:4982:2: warning: right shift count >= width of type [enabled by default]
drivers/net/e1000.c: In function 'e1000_configure_rx':
drivers/net/e1000.c:5126:2: warning: right shift count >= width of type [enabled by default]
This commit fixes the build warnings.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Peng Fan [Tue, 21 Jul 2015 08:15:21 +0000 (16:15 +0800)]
mtd: nand: mxs invalidate dcache before DMA read
Follow linux dma flow:
Before DMA read, be sure to invalidate the cache over the address
range of DMA buffer to prevent cache coherency problems.
After DMA read, invalidate dcache again.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Tim Harvey <tharvey@gateworks.com>
Peng Fan [Tue, 21 Jul 2015 08:15:19 +0000 (16:15 +0800)]
mtd: nand: mxs support oobsize bigger than 512
If ecc chunk data size is 512 and oobsize is bigger than 512, there is
a chance that block_mark_bit_offset conflicts with bch ecc area.
The following graph is modified from kernel gpmi-nand.c driver with
each data block 512 bytes. We can see that Block Mark conflicts with
ecc area from bch view. We can enlarge the ecc chunk size to avoid
this problem to those oobsize which is larger than 512.
| P |
|<----------------------------------------------------------------->|
| |
| (Block Mark) |
| P' | | | |
|<--------------------------------------------------->| D | | O'|
| |<--------->| |<->|
V V V V V
+---+--------------+-+--------------+-+--------------+-+----------+-+---+
| M | data |E| data |E| data |E| data |E| |
+---+--------------+-+--------------+-+--------------+-+----------+-+---+
^ ^
| O |
|<---------------->|
P : the page size for BCH module.
E : The ECC strength.
G : the length of Galois Field.
N : The chunk count of per page.
M : the metasize of per page.
C : the ecc chunk size, aka the "data" above.
P': the nand chip's page size.
O : the nand chip's oob size.
O': the free oob.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com> Reviewed-by: Marek Vasut <marex@denx.de> Tested-By: Tim Harvey <tharvey@gateworks.com>
Tested on the Marvell Armada XP DB-MV784MP-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Antoine Tenart <antoine.tenart@free-electrons.com> Cc: Ezeguil Garcia <ezequiel.garcia@free-electrons.com> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Scott Wood <scottwood@freescale.com>
Scott Wood [Sat, 27 Jun 2015 00:03:26 +0000 (19:03 -0500)]
nand: Sync with Linux v4.1
Update the NAND code to match Linux v4.1. The previous sync was
from Linux v3.15 in commit 4e67c57125290b25.
CONFIG_SYS_NAND_RESET_CNT is removed, as the upstream Linux code now
has its own timeout. Plus, CONFIG_SYS_NAND_RESET_CNT was undocumented
and not selected by any board.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Ezequiel Garcia [Wed, 21 May 2014 22:06:12 +0000 (19:06 -0300)]
mtd: Introduce mtd_block_isreserved()
In addition to mtd_block_isbad(), which checks if a block is bad or
reserved, it's needed to check if a block is reserved only (but not
bad). This commit adds an MTD interface for it, in a similar fashion to
mtd_block_isbad().
While here, fix mtd_block_isbad() so the out-of-bounds checking is done
before the callback check.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Tested-by: Pekon Gupta <pekon@ti.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[scottwood: Cherry-picked from Linux 8471bb73ba10ed67] Signed-off-by: Scott Wood <scottwood@freescale.com>
projects / u-boot / log