Stephen Warren [Thu, 29 May 2014 20:53:01 +0000 (14:53 -0600)]
usb: ci_udc: use a single descriptor for ep0
ci_udc currently points ep->desc at separate descriptors for IN and OUT.
These descriptors only differ in the ep address IN/OUT field. Modify the
code to use a single descriptor, and change that descriptor's ep address
to indicate IN/OUT as required. This removes some data duplication.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Thu, 29 May 2014 20:53:00 +0000 (14:53 -0600)]
usb: ci_udc: detect queued requests on ep0
The flipping of ep0 between IN and OUT relies on ci_ep_queue() consuming
the current IN/OUT setting immediately. If this is deferred to a later
point when the req is pulled out of ci_req->queue, then the IN/OUT
setting may have been changed since the req was queued, and state will
get out of sync. This condition doesn't occur today, but could if bugs
were introduced later, and this error-check will save a lot of debugging
time.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Now that we wait the correct specification-mandated time at the end of
usb_hub_power_on(), I suspect that CONFIG_USB_HUB_MIN_POWER_ON_DELAY has
no purpose.
For cm_t35.h, we already wait longer than the original MIN_POWER_ON_DELAY,
so this change is safe.
For gw_ventana.h, we will wait as long as the original MIN_POWER_ON_DELAY
iff pgood_delay was at least 200ms. I'm not sure if this is the case or
not, hence I've CC'd relevant people to test this change.
Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Mon, 19 May 2014 20:21:17 +0000 (14:21 -0600)]
usb: hub: fix power good delay timing
usb_hub_power_on() currently waits for the maximum of (a) the hub port's
power output to become good, (b) the max time the USB specification
allows a device to take to connect.
However, these two operations must occur in series rather than in
parallel. First, the power supply ramps up to the level required to
power the USB device, and then the device may take a certain amount of
time to connect (assert D+/D- pullups).
Related, the maximum time that a device has to assert pullups is 1s not
100ms.
This is explained in "Connect Timing ECN.pdf", itself part of
usb_20_042814.zip from www.usb.org.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Lukasz Majewski [Mon, 12 May 2014 08:43:36 +0000 (10:43 +0200)]
dfu: Introduction of the "dfu_hash_algo" env variable for checksum method setting
Up till now the CRC32 of received data was calculated unconditionally.
The standard crc32 implementation causes long delay when large images
were uploaded.
The "dfu_hash_algo" environment variable gives the opportunity to
disable on demand the hash (crc32) calculation.
It can be done without the need to recompile the u-boot binary.
By default the crc32 is calculated, which means that legacy behavior
has been preserved.
Simon Glass [Fri, 11 Apr 2014 02:01:35 +0000 (20:01 -0600)]
main: Make the execution path a little clearer in main.c
bootdelay_process() never returns in some circumstances, whichs makes the
control flow confusing. Change it so that the decision about how to execute
the boot command is made in the main_loop() code, so it is easier to follow.
Move CLI stuff to cli.c.
Simon Glass [Fri, 11 Apr 2014 02:01:32 +0000 (20:01 -0600)]
m68k: powerpc: Clean up do_mdm_init
This code seems unnecessarily complex. We really just need to check the
global_data. Now that is it all in one place, and not arch-specific, this
is pretty easy.
Heiko Schocher [Thu, 22 May 2014 10:43:05 +0000 (12:43 +0200)]
dm: rename device struct to udevice
using UBI and DM together leads in compiler error, as
both define a "struct device", so rename "struct device"
in include/dm/device.h to "struct udevice", as we use
linux code (MTD/UBI/UBIFS some USB code,...) and cannot
change the linux "struct device"
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Marek Vasut <marex@denx.de>
Andreas Bießmann [Mon, 19 May 2014 12:23:39 +0000 (14:23 +0200)]
mkimage: add atmelimage
The new atmelimage converts a machine code BLOB to bootable ROM image. Atmel
ROM has no sophisticated image format, it only checks the first 7 ARM vectors.
The vectors can contain valid B or LDR opcodes, the 6'th vector contains the
image size to load.
Additionally the PMECC header can be written by the atmelimage target. The
parameters must be given via the -n switch as a coma separated list. For
example:
A provided image can be checked for correct header setup. It prints out the
PMECC header parameters if it has one and the 6'th interrupt vector content.
Bo Shen [Thu, 24 Apr 2014 03:42:16 +0000 (11:42 +0800)]
ARM: atmel: at91sam9x5ek: convert to generic board
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following
warning on boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Bo Shen <voice.shen@atmel.com> Tested-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Thu, 24 Apr 2014 03:42:15 +0000 (11:42 +0800)]
ARM: atmel: at91sam9m10g45ek: convert to generic board
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following
warning on boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Bo Shen <voice.shen@atmel.com> Tested-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Thu, 24 Apr 2014 03:42:14 +0000 (11:42 +0800)]
ARM: atmel: sama5d3_xplained: convert to generic board
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following
warning on boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Thu, 24 Apr 2014 03:42:13 +0000 (11:42 +0800)]
ARM: atmel: sama5d3xek: convert to generic board
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following
warning on boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Bo Shen <voice.shen@atmel.com> Tested-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Wed, 19 Mar 2014 06:48:44 +0000 (14:48 +0800)]
ARM: atmel: switch to main crystal osc for SPL boot
If without switch to main crystal oscillator, the sama5d3 SoC will
use internal on chip RC oscillator.
In order to get better accuracy, switch to main crystal oscillator.
Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Ian Campbell [Wed, 14 May 2014 18:30:29 +0000 (19:30 +0100)]
net/designware: reorder struct dw_eth_dev to pack more efficiently.
On Thu, 2014-05-08 at 22:26 +0100, Ian Campbell wrote:
> The {r,t}xbuffs fields also need to be aligned. Previously this was done
> implicitly because they immediately followed the descriptor tables. Make this
> explicit and also move to the head of the struct.
Looks like I managed to not actually commit the move of the field to the
head of the struct! v3.1 follows....
Ian.
8<------------
>From 2937ba01841887317f6792709ed57cb86b5fc0cd Mon Sep 17 00:00:00 2001
From: Ian Campbell <ijc@hellion.org.uk>
Date: Thu, 1 May 2014 19:45:15 +0100
Subject: [PATCH] net/designware: reorder struct dw_eth_dev to pack more
efficiently.
The {tx,rx}_mac_descrtable fields are aligned to ARCH_DMA_MINALIGN, which could
be 256 or even larger. That means there is a potentially huge hole in the
struct before those fields, so move them to the front where they are better
packed.
Moving them to the front also helps ensure that so long as dw_eth_dev is
properly aligned (which it is since "net/designware: ensure device private data
is DMA aligned.") the {tx,rx}_mac_descrtable will be too, or at least avoids
having to worry too much about compiler specifics.
The {r,t}xbuffs fields also need to be aligned. Previously this was done
implicitly because they immediately followed the descriptor tables. Make this
explicit and also move to the head of the struct.
Ian Campbell [Thu, 8 May 2014 21:26:33 +0000 (22:26 +0100)]
net/designware: ensure cache invalidations are aligned to ARCH_DMA_MINALIGN
This is required at least on ARM.
When sending instead of simply invalidating the entire descriptor, flush
as little as possible while still respecting ARCH_DMA_MINALIGN, as
requested by Alexey.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Cc: Alexey Brodkin <abrodkin@synopsys.com>
Ian Campbell [Thu, 8 May 2014 21:26:32 +0000 (22:26 +0100)]
net/designware: ensure device private data is DMA aligned.
struct dw_eth_dev contains fields which are accessed via DMA, so make sure it
is aligned to a dma boundary. Without this I see:
ERROR: v7_dcache_inval_range - start address is not aligned - 0x7fb677e0
Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com> Acked-by: Marek Vasut <marex@denx.de>
Ian Campbell [Mon, 5 May 2014 10:52:30 +0000 (11:52 +0100)]
sunxi: non-FEL SPL boot support for sun7i
Add support for booting from an MMC card.
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Henrik Nordström <henrik@henriknordstrom.net> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Marek Vasut <marex@denx.de> Cc: Tom Cubie <Mr.hipboi@gmail.com> Reviewed-by: Tom Rini <trini@ti.com>
Ian Campbell [Mon, 5 May 2014 13:42:31 +0000 (14:42 +0100)]
sunxi: mmc support
On Mon, 2014-05-05 at 14:18 +0200, Stefan Roese wrote:
> > + case 1:
> > +#if CONFIG_MMC1_PG
> Are you sure that this is correct and shouldn't be:
>
> +#ifdef CONFIG_MMC1_PG
>
> ?
It's "correct" in so far as it works (the boards.cfg config stuff
#defines things to 1), but I think you are right that it isn't the
preferred style. But...
> A quick scan through this patch series shows that this define
> is not set at all. Perhaps its outdated? Or is it used to support
> some other sunxi SoC? Not sure, perhaps it should be removed for
> now.
...I had thought that it was to support some other board which wasn't
being upstreamed right now, so eventually useful and harmless for now,
but I've just checked and it isn't actually used by any of the boards in
u-boot-sunxi.git. So rather than fix it to use #ifdef lets drop it.
Rather than resend the entire series, here is v5.1 of this patch.
> Other than this please add my:
>
> Reviewed-by: Stefan Roese <sr@denx.de>
Thanks!
8<---------------------------------
>From 20704e35a41664de5f516ed0e02981ac06085102 Mon Sep 17 00:00:00 2001
From: Ian Campbell <ijc@hellion.org.uk>
Date: Fri, 7 Mar 2014 04:29:39 +0000
Subject: [PATCH v5.1 7/8] sunxi: mmc support
This adds support for the MMC controller on the Allwinner A20 (sun7i)
processor.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Luke Leighton <lkcl@lkcl.net> Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Wills Wang <wills.wang.open@gmail.com> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Stefan Roese <sr@denx.de> Cc: Tom Cubie <Mr.hipboi@gmail.com> Cc: Aaron Maoye <leafy.myeh@allwinnertech.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Reviewed-by: Tom Rini <trini@ti.com>
Ian Campbell [Mon, 5 May 2014 10:52:27 +0000 (11:52 +0100)]
sunxi: add support for Cubietruck booting in FEL mode
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Jens Kuske <jenskuske@gmail.com> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Tom Rini <trini@ti.com> Reviewed-by: Marek Vasut <marex@denx.de>
Ian Campbell [Mon, 5 May 2014 10:52:26 +0000 (11:52 +0100)]
sunxi: add sun7i cpu, board and start of day support
This patch adds generic board, start of day and basic build system support for
the Allwinner A20 (sun7i) processor. This code will not been compiled until the
build is hooked up in a later patch. It has been split out to keep the patches
manageable.
Signed-off-by: Adam Sampson <ats@offog.org> Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com> Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Emilio López <emilio@elopez.com.ar> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Jens Kuske <jenskuske@gmail.com> Signed-off-by: Luc Verhaegen <libv@skynet.be> Signed-off-by: Luke Leighton <lkcl@lkcl.net> Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Patrick Wood <patrickhwood@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Wills Wang <wills.wang.open@gmail.com> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Marek Vasut <marex@denx.de> Cc: Tom Cubie <Mr.hipboi@gmail.com> Reviewed-by: Tom Rini <trini@ti.com>
Ian Campbell [Mon, 5 May 2014 10:52:25 +0000 (11:52 +0100)]
sunxi: add sun7i dram setup support
This patch adds DRAM initialisation support for the Allwinner A20 (sun7i)
processor. This code will not been compiled until the build is hooked up in a
later patch. It has been split out to keep the patches manageable.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Emilio López <emilio@elopez.com.ar> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Jens Kuske <jenskuske@gmail.com> Signed-off-by: Luke Leighton <lkcl@lkcl.net> Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Marek Vasut <marex@denx.de> Cc: Tom Cubie <Mr.hipboi@gmail.com> Reviewed-by: Tom Rini <trini@ti.com>
Ian Campbell [Mon, 5 May 2014 10:52:24 +0000 (11:52 +0100)]
sunxi: add sun7i pinmux and gpio support
This patch adds the basic pinmux and gpio support for the Allwinner A20 (sun7i)
processor. This code will not been compiled until the build is hooked up in a
later patch. It has been split out to keep the patches manageable.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ma Haijun <mahaijuns@gmail.com> Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Henrik Nordström <henrik@henriknordstrom.net> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Tom Rini <trini@ti.com> Acked-by: Marek Vasut <marex@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Tom Cubie <Mr.hipboi@gmail.com> Reviewed-by: Tom Rini <trini@ti.com>
Ian Campbell [Mon, 5 May 2014 10:52:23 +0000 (11:52 +0100)]
sunxi: add sun7i clocks and timer support.
This patch adds the basic clocks and timer support for the Allwinner A20
(sun7i) processor. This code will not been compiled until the build is hooked
up in a later patch. It has been split out to keep the patches manageable.
Some of the code here is common to multiple sunxi subarchtectures, hence files
are named sun4i which is the earliest similar variant.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Emilio López <emilio@elopez.com.ar> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net> Signed-off-by: Jens Kuske <jenskuske@gmail.com> Signed-off-by: Luke Leighton <lkcl@lkcl.net> Signed-off-by: Oliver Schinagl <oliver@schinagl.nl> Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Cc: Stefan Roese <sr@denx.de> Cc: Tom Cubie <Mr.hipboi@gmail.com> Reviewed-by: Tom Rini <trini@ti.com>
Stefan Agner [Wed, 23 Apr 2014 16:17:51 +0000 (18:17 +0200)]
arm: vf610: add DDR_SEL_PAD_CONTR register
Set DDR_SEL_PAD_CONTR register explicitly to DDR3 which solves RAM
issues with newer silicon (1.1). This register was added in revision
4 of the Vybrid Reference Manual.
Michael Walle [Tue, 1 Apr 2014 18:09:14 +0000 (20:09 +0200)]
lsxl: rework boot scripts
Move addresses for kernel, ramdisk and fdt blob to own variables. Add dtb
blob loading to all existing boot scripts, dtb filenames were taken from
vanilla kernel. Introduce new boot script bootcmd_legacy, which only loads
a kernel and a ramdisk. Make this the default boot script. This should also
restore the behaviour of the original bootloader.
Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Tom Rini <trini@ti.com> Signed-off-by: Michael Walle <michael@walle.cc>
Lokesh Vutla [Mon, 12 May 2014 08:19:33 +0000 (13:49 +0530)]
ARM: OMAP: Fix omap_sdram_size calculation
Last section of DMM is used for trapping tiler unmapped sections.
Corresponding trap_size should be deducted from total SDRAM size
only if trap section is overlapping with available SDRAM
based on DMM sections. Fixing the same.
Heiko Schocher [Wed, 14 May 2014 10:40:27 +0000 (12:40 +0200)]
arm, am33xx: Enable CONFIG_SYS_GENERIC_BOARD for siemens boards
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Samuel Egli <samuel.egli@siemens.com> Cc: Roger Meier <r.meier@siemens.com> Tested-by: Samuel Egli <samuel.egli@siemens.com>
Ash Charles [Wed, 14 May 2014 15:34:34 +0000 (08:34 -0700)]
omap4: duovero: Add Gumstix DuoVero machine.
This adds the Gumstix DuoVero machine [1]. This is a OMAP4430-based
computer-on-module (COM aka SOM) that can be mounted on various
expansion boards with different peripherals.
Signed-off-by: Ash Charles <ash@gumstix.com>
[trini: Rename gpmc_enable_gpmc_cs_config to gpmc_enable_gpmc_net_config] Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Fri, 16 May 2014 17:02:24 +0000 (13:02 -0400)]
armv7:TI: Add <asm/ti-common/sys_proto.h> and migrate omap_hw_init_context
The omap_hw_init_context function (and assorted helpers) is the same for
all OMAP-derived parts as when CHSETTINGS are used, that's the same and
our DDR base is also always the same. In order to make this common we
simply need to update the names of the define for DDR address space
which is also common.
Cc: Sricharan R. <r.sricharan@ti.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
pekon gupta [Thu, 8 May 2014 16:13:47 +0000 (21:43 +0530)]
ARM: omap: merge GPMC initialization code for all platform
GPMC controller on TI's OMAP SoC is general purpose controller to interface
with different types of external devices like;
- parallel NOR flash
- parallel NAND flash
- OneNand flash
- SDR RAM
- Ethernet Devices like LAN9220
Though GPMC configurations may be different for each platform depending on
clock-frequency and external device interfacing with controller. But
initialization sequence remains common across all platfoms.
Thus this patch merges gpmc_init() scattered in different arch-xx/mem.c
files into single omap-common/mem-common.c
However, actual platforms specific register config values are still sourced
from corresponding platform specific headers like;
AM33xx: arch/arm/include/asm/arch-am33xx/mem.h
OMAP3: arch/arm/include/asm/arch-omap3/mem.h
OMAP4: arch/arm/include/asm/arch-omap4/mem.h
OMAP4: arch/arm/include/asm/arch-omap5/mem.h
Also, CONFIG_xx passed by board-profile decide config for which set of macros
need to be used for initialization
CONFIG_NAND: initialize GPMC for NAND device
CONFIG_NOR: initialize GPMC for NOR device
CONFIG_ONENAND: initialize GPMC for ONENAND device
Signed-off-by: Pekon Gupta <pekon@ti.com>
[trini: define GPMC_SIZE_256M for omap3] Signed-off-by: Tom Rini <trini@ti.com>
Alexey Brodkin [Fri, 16 May 2014 08:54:17 +0000 (12:54 +0400)]
examples: select libgcc for non-default architecture
In case of multilib-enabled toolchains if default architecture differ from
the one examples are being built for linker will fail to link example object
files with libgcc of another (non-compatible) architecture.
Interesting enough for years in main Makefile we used CFLAGS/c_flags for this
but not for examples.
So fixing it now.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Rini <trini@ti.com> Cc: Wolfgang Denx <wd@denx.de> Acked-by: WOlfgang Denk <wd@denx.de> Acked-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
pekon gupta [Thu, 8 May 2014 16:13:46 +0000 (21:43 +0530)]
ARM: omap5: add platform specific info for GPMC and ELM controllers
This patch moves platform specific information for GPMC and ELM controller
into separate header files, so that any derivative devices do not mess other
header files.
Platform specific information added into arch-xx/../hardware.h
- CPU related platform specific details like base-address of GPMC and ELM
Platform specific information added into arch-xx/../mem.h
- Generic configs for GPMC and ELM initialization.
- Hardware parameters or constrains specific to GPMC and ELM IP like;
number of max number of chip-selects available
pekon gupta [Thu, 8 May 2014 16:13:45 +0000 (21:43 +0530)]
ARM: omap4: add platform specific info for GPMC and ELM controllers
This patch moves platform specific information for GPMC and ELM controller
into separate header files, so that any derivative devices do not mess other
header files.
Platform specific information added into arch-xx/../hardware.h
- CPU related platform specific details like base-address of GPMC and ELM
Platform specific information added into arch-xx/../mem.h
- Generic configs for GPMC and ELM initialization.
- Hardware parameters or constrains specific to GPMC and ELM IP like;
number of max number of chip-selects available
Ash Charles [Wed, 21 May 2014 21:04:52 +0000 (14:04 -0700)]
Add Board Revision for Wireless chip
Gumstix Overo COMs with board revision 0x4 use a different Wifi and
Bluetooth module: Wi2Wi's W2CBW0015. No other code changes are required
in u-boot---just handling of this particular board revision.
Ash Charles [Wed, 21 May 2014 21:04:51 +0000 (14:04 -0700)]
arm: omap3: Fix omap3_overo SPL boot hangup
Patch f33b9bd3
[arm: omap3: Enable clocks for peripherals only if they are used]
breaks SPL booting on Overo. Since some gpio inputs are
read to detect the board revision. But with this patch above, the
clocks to the GPIO subsystems are not enabled per default any more.
The GPIO banks need to be configured specifically now.
The linux kernel is at nand0,3 using the current layout, but is best
accessed through the partition label "linux". Since CONFIG_CMD_MTDPARTS is
defined the CONFIG_JFFS2 settings are unreferenced; use "setenv partition
rootfs" to set the default mtd partition for jffs2.
Signed-off-by: Peter A. Bigot <pab@pabigot.com> Tested-by: Ash Charles <ash@gumstix.com>
Ash Charles [Wed, 21 May 2014 21:04:48 +0000 (14:04 -0700)]
OMAP3: overo: add command support for mtd and ubi
The NAND linux partition format default was changed from jffs2 to ubi in 254973e6df0e48f1a72b67905185c774dcd9f394 but the corresponding commands were
not enabled.
Signed-off-by: Peter A. Bigot <pab@pabigot.com> Tested-by: Ash Charles <ash@gumstix.com>
omap4: allow the use of a plain text env file instead boot scripts
For production systems it is better to use script images since
they are protected by checksums and carry valuable information like
name and timestamp. Also, you can't validate the content passed to
env import.
But for development, it is easier to use the env import command and
plain text files instead of script-images.
Since both OMAP4 supported boards (Panda and TI SDP4430) are used
primarily for development, this patch allows U-Boot to load env var
from a text file in case that an boot.scr script-image is not present.
The variable uenvcmd (if existent) will be executed (using run) after
uEnv.txt was loaded. If uenvcmd doesn't exist the default boot sequence
will be started.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by: Nishanth Menon <nm@ti.com> Signed-off-by: Peter A. Bigot <pab@pabigot.com> Tested-by: Ash Charles <ash@gumstix.com>
Tom Rini [Fri, 23 May 2014 13:19:05 +0000 (09:19 -0400)]
esdhc/usdhc: Fix warning when CONFIG_SYS_FSL_ESDHC_USE_PIO is not set
In 7168977 we made calls to check_and_invalidate_dcache_range()
conditional on !CONFIG_SYS_FSL_ESDHC_USE_PIO. Only define this function
in this case as well.
Stephen Warren [Wed, 7 May 2014 18:19:02 +0000 (12:19 -0600)]
mmc: provide a select_hwpart implementation for get_device()
This enables specifying which eMMC HW partition to target for any U-Boot
command that uses the generic get_partition() function to parse its
command-line arguments.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Wed, 7 May 2014 18:19:01 +0000 (12:19 -0600)]
disk: support devices with HW partitions
Some device types (e.g. eMMC) have hardware-level partitions (for eMMC,
separate boot and user data partitions). This change allows the user to
specify the HW partition they wish to access when passing a device ID to
U-Boot Commands such as part, ls, load, ums, etc.
The syntax allows an optional ".$hwpartid" to be appended to the device
name string for those commands.
Existing syntax, for MMC device 0, default HW partition ID, SW partition
ID 1:
ls mmc 0:1 /
New syntax, for MMC device 0, HW partition ID 1 (boot0), SW partition
ID 2:
ls mmc 0.1:2 /
For my purposes, this is most useful for the ums (USB mass storage
gadget) command, but there's no reason not to allow the new syntax
globally.
This patch adds the core support infra-structure. The next patch will
provide the implementation for MMC.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Stephen Warren <swarren@nvidia.com>
projects / u-boot / log