Ladislav Michl [Tue, 12 Jul 2016 18:28:15 +0000 (20:28 +0200)]
armv7: add reset timeout to identify_nand_chip
identify_nand_chip hangs forever in loop when NAND is not present.
As IGEPv2 comes either with NAND or OneNAND flash, add reset timeout
to let function fail gracefully allowing caller to know NAND is
not present. On NAND equipped board, reset succeeds on first read,
so 1000 loops seems to be safe timeout.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Thomas Gleixner [Tue, 12 Jul 2016 18:28:12 +0000 (20:28 +0200)]
spl: Lightweight UBI and UBI fastmap support
Booting a payload out of NAND FLASH from the SPL is a crux today, as
it requires hard partioned FLASH. Not a brilliant idea with the
reliability of todays NAND FLASH chips.
The upstream UBI + UBI fastmap implementation which is about to
brought to u-boot is too heavy weight for SPLs as it provides way more
functionality than needed for a SPL and does not even fit into the
restricted SPL areas which are loaded from the SoC boot ROM.
So this provides a fast and lightweight implementation of UBI scanning
and UBI fastmap attach. The scan and logical to physical block mapping
code is developed from scratch, while the fastmap implementation is
lifted from the linux kernel source and stripped down to fit the SPL
needs.
The text foot print on the board which I used for development is:
6854 0 0 6854 1abd
drivers/mtd/ubispl/built-in.o
Attaching a NAND chip with 4096 physical eraseblocks (4 blocks are
reserved for the SPL) takes:
In full scan mode: 1172ms
In fastmap mode: 95ms
The code requires quite some storage. The largest and unknown part of
it is the number of fastmap blocks to read. Therefor the data
structure is not put into the BSS. The code requires a pointer to free
memory handed in which is initialized by the UBI attach code itself.
See doc/README.ubispl for further information on how to use it.
This shares the ubi-media.h and crc32 implementation of drivers/mtd/ubi
There is no way to share the fastmap code, as UBISPL only utilizes the
slightly modified functions ubi_attach_fastmap() and ubi_scan_fastmap()
from the original kernel ubi fastmap implementation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Acked-by: Heiko Schocher <hs@denx.de> Reviewed-by: Tom Rini <trini@konsulko.com>
Thomas Gleixner [Tue, 12 Jul 2016 18:28:10 +0000 (20:28 +0200)]
nand_spl_simple: Add a simple NAND read function
To support UBI in SPL we need a simple NAND read function. Add one to
nand_spl_simple and keep it as simple as it goes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Acked-by: Scott Wood <oss@buserror.net> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Michal Simek [Thu, 14 Jul 2016 11:11:37 +0000 (13:11 +0200)]
dm: clk: Remove simple version of clk_get_by_index/name()
Simple version of clk_get_by_index() added by:
"dm: clk: Add a simple version of clk_get_by_index()"
(sha1: a4b10c088c4f6ef2e2bba33e8cfea369bcbbce44)
is only working for #clock-cells=<1> but not for
any other values. Fixed clocks is using #clock-cells=<0>
which requires full implementation.
Remove simplified versions of clk_get_by_index() and use full version.
Also remove empty clk_get_by_name() which is failing when it is called
which is useless.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Stephen Warren <swarren@nvidia.com>
Michal Simek [Thu, 14 Jul 2016 12:40:03 +0000 (14:40 +0200)]
serial: zynq: Read information about clock from DT
Read information about clock frequency from DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Michal Simek [Wed, 27 Apr 2016 14:07:20 +0000 (16:07 +0200)]
spl: Fix compilation warnings for arm64
Make code 64bit aware.
Warnings:
+../arch/arm/lib/spl.c: In function ‘jump_to_image_linux’:
+../arch/arm/lib/spl.c:63:3: warning: cast to pointer from integer of
different size [-Wint-to-pointer-cast]
+../common/spl/spl_fat.c: In function ‘spl_load_image_fat’:
+../common/spl/spl_fat.c:91:33: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Disable internal clock by clearing the internal
clock enable bit. This bit needs to be cleared too
when we stop the SDCLK for changing the frequency
divisor. This bit should be set to zero when the
device is not using the Host controller.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 6 Jun 2016 08:58:40 +0000 (10:58 +0200)]
api: Disable api_net when DM is used
When CONFIG_API is selected with DM_ETH this
error is present:
api/api_net.c: In function 'dev_enum_net':
api/api_net.c:61:35: warning: initialization from incompatible pointer
type
struct eth_device *eth_current = eth_get_dev();
^
api/api_net.c:68:39: error: dereferencing pointer to incomplete type
memcpy(di->di_net.hwaddr, eth_current->enetaddr, 6);
^
Disable api_net functions when ETH_DM is selected.
Signed-off-by: Chris Johns <chrisj@rtems.org> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tom Rini [Thu, 21 Jul 2016 19:38:13 +0000 (15:38 -0400)]
Revert "stm32: Change USART port to USART6 for stm32f746 discovery board"
Per Vikas' request, the problem this commit is supposed to be solving is
something he doesn't see and further this introduces additional hardware
requirements.
Scott Wood [Tue, 19 Jul 2016 22:52:06 +0000 (17:52 -0500)]
powerpc/85xx: Increase fdt address
Loading the fdt at 0xc00000 fails if the uncompressed kernel image is
greater than 12 MiB, which is quite common with modern kernels and
multiplatform defconfigs. Move fdtaddr to 0x1e00000 which is just under
the ramdiskaddr on most targets.
Signed-off-by: Scott Wood <oss@buserror.net> Cc: Peter Tyser <ptyser@xes-inc.com> Cc: Dirk Eibach <eibach@gdsys.de> Cc: Andy Fleming <afleming@gmail.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com> Reviewed-by: York Sun <york.sun@nxp.com>
For mpc85xx SoCs, the core begins execution from address 0xFFFFFFFC.
In non-secure boot scenario from NAND, this address will map to CPC
configured as SRAM. But in case of secure boot, this default address
always maps to IBR (Internal Boot ROM).
The IBR code requires that the bootloader(U-boot) must lie in 0 to 3.5G
address space i.e. 0x0 - 0xDFFFFFFF.
For secure boot target from NAND, the text base for SPL is kept same as
non-secure boot target i.e. 0xFFFx_xxxx but the SPL U-boot binary will
be copied to CPC configured as SRAM with address in 0-3.5G(0xBFFC_0000)
As a the virtual and physical address of CPC would be different. The
virtual address 0xFFFx_xxxx needs to be mapped to physical address
0xBFFx_xxxx.
Create a new PBI file to configure CPC as SRAM with address 0xBFFC0000
and update DCFG SCRTACH1 register with location of Header required for
secure boot.
While P3041 has a 1MB CPC and does not require SPL. On T104x, CPC
is only 256K and thus SPL framework is used.
The changes are only applicable for SPL U-Boot running out of CPC SRAM
and not the next level U-Boot loaded on DDR.
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
powerpc/mpc85xx: SECURE BOOT- Enable chain of trust in SPL
As part of Chain of Trust for Secure boot, the SPL U-Boot will validate
the next level U-boot image. Add a new function spl_validate_uboot to
perform the validation.
Enable hardware crypto operations in SPL using SEC block.
In case of Secure Boot, PAMU is not bypassed. For allowing SEC block
access to CPC configured as SRAM, configure PAMU.
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com> Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: York Sun <york.sun@nxp.com>
Kevin Hao [Fri, 8 Jul 2016 03:25:15 +0000 (11:25 +0800)]
mpc83xx: make it bootable with the latest kernel
Due to the blow up of the latest kernel size, the default gnuzip
size (8M) seems too small. The yocto kernel size I built for
mpc8315erdb board is 5294393, and it can't be boot by using the
latest u-boot. So expand gnuzip buffer for all the mpc83xx boards
to fix this issue.
Robert P. J. Day also pointed that the kernel partition on the NAND
flash is also too small, fix it at the same time.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Kevin Hao <kexin.hao@windriver.com> Reviewed-by: York Sun <york.sun@nxp.com>
Kevin Hao [Fri, 8 Jul 2016 03:25:14 +0000 (11:25 +0800)]
mpc83xx: fix the corruption of u-boot when saveenv
Robert P. J. Day has pointed that the value of SYS_MONITOR_LEN in
MPC8315ERDB.h is smaller than the u-boot.bin. This will cause the
overlap between the code of u-boot and the environment variable.
So when executing saveenv, it will corrupt the code of u-boot and
causes the board not boot. Fix this for all the mpc83xx boards by
reserving a 512K area.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Kevin Hao <kexin.hao@windriver.com> Reviewed-by: York Sun <york.sun@nxp.com>
Stephen Warren [Mon, 18 Jul 2016 23:01:51 +0000 (17:01 -0600)]
ARM: tegra: pick up actual memory size
On Tegra186, U-Boot is booted by the binary firmware as if it were a
Linux kernel. Consequently, a DTB is passed to U-Boot. Cache the address
of that DTB, and parse the /memory/reg property to determine the actual
RAM regions that U-Boot and subsequent EL2/EL1 SW may actually use.
Given the binary FW passes a DTB to U-Boot, I anticipate the suggestion
that U-Boot use that DTB as its control DTB. I don't believe that would
work well, so I do not plan to put any effort into this. By default the
FW-supplied DTB is the L4T kernel's DTB, which uses non-upstreamed DT
bindings. U-Boot aims to use only upstreamed DT bindings, or as close as
it can get. Replacing this DTB with a DTB using upstream bindings is
physically quite easy; simply replace the content of one of the GPT
partitions on the eMMC. However, the binary FW at least partially relies
on the existence/content of some nodes in the DTB, and that requires the
DTB to be written according to downstream bindings. Equally, if U-Boot
continues to use appended DTBs built from its own source tree, as it does
for all other Tegra platforms, development and deployment is much easier.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Mon, 18 Jul 2016 23:01:50 +0000 (17:01 -0600)]
ARM: Add save_boot_params for ARMv8
Implement a hook to allow boards to save boot-time CPU state for later
use. When U-Boot is chain-loaded by another bootloader, CPU registers may
contain useful information such as system configuration information. This
feature mirrors the equivalent ARMv7 feature.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Rev A03 of P2180 requires some PMIC programming adjustments, yet the
PMIC's own OTP has not been updated. Consequently, U-Boot must make
these changes itself.
NVIDIA's syseng team has confirmed that these changes can be enabled on
all board revisions without issue.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Mon, 18 Jul 2016 18:17:11 +0000 (12:17 -0600)]
ARM: tegra: add IVC protocol implementation
IVC (Inter-VM Communication) protocol is a Tegra-specific IPC (Inter
Processor Communication) framework. Within the context of U-Boot, it is
typically used for communication between the main CPU and various
auxiliary processors. In particular, it will be used to communicate with
the BPMP (Boot and Power Management Processor) on Tegra186 in order to
manipulate clocks and reset signals.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Mon, 18 Jul 2016 18:15:05 +0000 (12:15 -0600)]
ARM: tegra: unify Tegra186 Makefile a bit
Many files in arch/arm/mach-tegra are compiled conditionally based on
Kconfig variables, or applicable to all platforms. We can let the main
Tegra Makefile handle compiling (or not) those files to avoid each SoC-
specific Makefile needing to duplicate entries for those files. This
leaves the SoC-specific Makefiles to compile truly SoC-specific code.
In the future, we'll hopefully add Kconfig variables for all the other
files, and refactor those files, and so reduce the need for SoC-specific
Makefiles and/or ifdefs in the Makefiles.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Mon, 18 Jul 2016 18:15:04 +0000 (12:15 -0600)]
ARM: tegra: split p2771-0000 build
There are multiple versions of p2771-0000 board. There are SW visible
incompatible differences between the versions, and they are relevant to
U-Boot. Create separate "A02" and "B00" defconfigs (named after the first
and/or only board rev the defconfig supports) so that users can select
which build they want.
With the minimal set of HW currently enabled in U-Boot, the differences
are irrelevant, hence the DT files aren't different. However, that will
change in a future patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
The enum conversion broke the compatibility with existing uImage
files. Reverting 555f45d8f916 will cause build error unfortunately,
so here is a more easy fix.
I dug the git history and figured out the gap was introduced by
commit 1117cbf2adac ("nios: remove nios-32 arch"). So, I revived
IH_ARCH_NIOS just for filling the gap.
I added comments to each enum block. Once we assign a value to
IH_... it is not allowed to change it.
Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Benjamin Kamath [Wed, 29 Jun 2016 23:44:38 +0000 (16:44 -0700)]
powerpc: MPC8544DS: revert typo in I2C offset value
I2C offset was changed by commit 00f792e0 (added multibus support)
from 0x3100 to 0x3000. This typo leads to error when reading SPD
from DDR DIMMs.
Signed-off-by: Benjamin Kamath <bkamath@spaceflight.com> Signed-off-by: York Sun <york.sun@nxp.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
mtd: cfi_flash: fix polling for bit XSR.7 on Intel chips
flash_full_status_check() checks bit XSR.7 on Intel chips. This
should be done by only checking bit 7 and not by comparing the
whole status byte or word with 0x80.
This fixes the non-working block erase in the pflash emulation
of Qemu when used with the MIPS Malta board. MIPS Malta uses x32
mode to access the pflash device. In x32 mode Qemu mirrors the
lower 16 bits of the status word into the upper 16 bits. Thus
the CFI driver gets a status word of 0x8080 in x32 mode. If
flash_full_status_check() uses flash_isequal(), then it polls for
XSR.7 by comparing 0x8080 with 0x80 which never becomes true.
Reported-by: Alon Bar-Lev <alon.barlev@gmail.com> Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Signed-off-by: Stefan Roese <sr@denx.de>
Hou Zhiqiang [Tue, 28 Jun 2016 12:18:17 +0000 (20:18 +0800)]
ARMv8/ls1043ardb: Integrate FSL PPA
The PPA use PSCI to make secondary cores bootup. So when PPA was
enabled, add the CONFIG_ARMV8_PSCI to identify the SMP boot-method
between PSCI and spin-table.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Hou Zhiqiang [Tue, 28 Jun 2016 12:18:15 +0000 (20:18 +0800)]
ARMv8/Layerscape: switch SMP method accordingly
If the PSCI and PPA is ready, skip the fixup for spin-table and
waking secondary cores. Otherwise, change SMP method to spin-table,
and the device node of PSCI will be removed.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Hou Zhiqiang [Tue, 28 Jun 2016 12:18:13 +0000 (20:18 +0800)]
ARMv8: add the secure monitor firmware framework
This framework is introduced for ARMv8 secure monitor mode firmware.
The main functions of the framework are, on EL3, verify the firmware,
load it to the secure memory and jump into it, and while it returned
to U-Boot, do some necessary setups at the 'target exception level'
that is determined by the respective secure firmware.
So far, the framework support only FIT format image, and need to define
the name of which config node should be used in 'configurations' and
the name of property for the raw secure firmware image in that config.
The FIT image should be stored in Byte accessing memory, such as NOR
Flash, or else it should be copied to main memory to use this framework.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
Hou Zhiqiang [Tue, 28 Jun 2016 12:18:12 +0000 (20:18 +0800)]
armv8: fsl-layerscape: add i/d-cache enable function to enable_caches
This function assume that the d-cache and MMU has been enabled earlier,
so it just created MMU table in main memory. But the assumption is not
always correct, for example, the early setup is done in EL3, while
enable_caches() is called when the PE has turned into another EL.
Define the function mmu_setup() for fsl-layerscape to cover the weak
one.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
York Sun [Fri, 24 Jun 2016 23:46:23 +0000 (16:46 -0700)]
armv8: layerscape: Convert to use common MMU framework
Drop platform code to create static MMU tables. Use common framework
to create MMU tables on the run. Tested on LS2080ARDB with secure and
non-secure ram scenarios.
Tom Rini [Fri, 15 Jul 2016 19:30:33 +0000 (15:30 -0400)]
configs: Add more CONFIG_ARMV7_PSCI_NR_CPUS entries
The code had assumed 4 CPUS before and now we have this configurable.
For now, set this to the previous default.
Cc: Chander Kashyap <k.chander@samsung.com> Cc: Steve Rae <steve.rae@raedomain.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com>
York Sun [Fri, 24 Jun 2016 23:46:21 +0000 (16:46 -0700)]
armv8: mmu: split block if necessary
When page tables are created, allow later table to be created on
previous block entry. Splitting block feature is already working
with current code. This patch only rearranges the code order and
adds one condition to call split_block().
York Sun [Fri, 24 Jun 2016 23:46:19 +0000 (16:46 -0700)]
armv8: Add tlb_allocated to arch global data
When secure ram is used, MMU tables have to be put into secure ram.
To use common MMU code, gd->arch.tlb_addr will be used to host TLB
entry pointer. To save allocated memory for later use, tlb_allocated
variable is added to global data structure.
Chen-Yu Tsai [Sun, 19 Jun 2016 04:38:39 +0000 (12:38 +0800)]
ARM: Add CONFIG_ARMV7_SECURE_MAX_SIZE and check size of secure section
As the PSCI implementation grows, we might exceed the size of the secure
memory that holds the firmware.
Add a configurable CONFIG_ARMV7_SECURE_MAX_SIZE so platforms can define
how much secure memory is available. The linker then checks the size of
the whole secure section against this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Chen-Yu Tsai [Sun, 19 Jun 2016 04:38:38 +0000 (12:38 +0800)]
ARM: PSCI: Remove unused psci_text_end symbol
psci_text_end was used to calculate the PSCI stack address following the
secure monitor text. Now that we have an explicit secure stack section,
this is no longer used.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Chen-Yu Tsai [Sun, 19 Jun 2016 04:38:36 +0000 (12:38 +0800)]
ARM: Add an empty secure stack section
Until now we've been using memory beyond psci_text_end as stack space
for the secure monitor or PSCI implementation, even if space was not
allocated for it.
This was partially fixed in ("ARM: allocate extra space for PSCI stack
in secure section during link phase"). However, calculating stack space
from psci_text_end in one place, while allocating the space in another
is error prone.
This patch adds a separate empty secure stack section, with space for
CONFIG_ARMV7_PSCI_NR_CPUS stacks, each 1 KB. There's also
__secure_stack_start and __secure_stack_end symbols. The linker script
handles calculating the correct VMAs for the stack section. For
platforms that relocate/copy the secure monitor before using it, the
space is not allocated in the executable, saving space.
For platforms that do not define CONFIG_ARMV7_PSCI_NR_CPUS, a whole page
of stack space for 4 CPUs is allocated, matching the previous behavior.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
ARM: PSCI: Add missing CONFIG_ARMV7_PSCI_NR_CPUS for PSCI enabled platforms
The original PSCI implementation assumed CONFIG_ARMV7_PSCI_NR_CPUS=4.
Add this to platforms that have not defined it, using CONFIG_MAX_CPUS if
it is defined, or the actual number of cores for the given platform.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Chen-Yu Tsai [Sun, 19 Jun 2016 04:38:34 +0000 (12:38 +0800)]
ARM: Page align secure section only when it is executed in situ
Targets that define CONFIG_ARMV7_SECURE_BASE will copy the secure section
to another address before execution.
Since the secure section in the u-boot image is only storage, there's
no reason to page align it and increase the binary image size.
Page align the secure section only when CONFIG_ARMV7_SECURE_BASE is not
defined. And instead of just aligning the __secure_start symbol, align
the whole .__secure_start section. This also makes the section empty,
so we need to add KEEP() to the input entry to prevent the section from
being garbage collected.
Also use ld constant "COMMONPAGESIZE" instead of hardcoded page size.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Chen-Yu Tsai [Sun, 19 Jun 2016 04:38:32 +0000 (12:38 +0800)]
sunxi: Move remaining PSCI assembly code to C
This patch finishes the rewrite of sunxi specific PSCI parts into C
code.
The assembly-only stack setup code has been factored out into a common
function for ARMv7. The GIC setup code can be renamed as psci_arch_init.
And we can use an empty stub function for psci_text_end.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Chen-Yu Tsai [Sun, 19 Jun 2016 04:38:31 +0000 (12:38 +0800)]
ARM: PSCI: Split out common stack setup code from psci_arch_init
Every platform has the same stack setup code in assembly as part of
psci_arch_init.
Move this out into a common separate function, psci_stack_setup, for
all platforms. This will allow us to move the remaining parts of
psci_arch_init into C code, or drop it entirely.
Also provide a stub no-op psci_arch_init for platforms that don't need
their own specific setup code.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Sat, 9 Jul 2016 20:20:00 +0000 (22:20 +0200)]
sunxi: Add defconfig and dts file for the Orange Pi Lite SBC
The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM,
micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector,
sdio attached rtl8189ftv wifi and an ir receiver.
The dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 9 Jul 2016 13:31:47 +0000 (15:31 +0200)]
sunxi: Use BROM stored boot_media value to determine our boot-source
Now that we know that the BROM stores a value indicating the boot-source
at the beginning of SRAM, use that instead of trying to recreate the
BROM's boot probing.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sat, 9 Jul 2016 07:56:56 +0000 (09:56 +0200)]
sunxi: Remove some unnecessary #ifdefs
We always define CONFIG_MISC_INIT_R on sunxi and misc_init_r is never
called in the spl, so the linker will optimize it and parse_spl_header(),
of which it is the only caller, away.
On the tests I've done (Orange Pi PC build) the SPL actually becomes
8 bytes smaller with this patch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hans de Goede [Sun, 26 Jun 2016 11:34:42 +0000 (13:34 +0200)]
sunxi: Add support for multiple ethadrr-esses
Currently we fill ethaddr with a fixed unique address based on the SoCs
serial (from the sid) to make sure that boards which use the integrated
emac / gmac get a fixed mac rather then a random one.
On some boards the wifi does not come with a fixed mac either, so we need
to also set eth1addr.
This commit changes the ethaddr setting code to check for ethernet%d
aliases (as fdt_fixup_ethernet does) and set an ethaddr variable for
all present aliases.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
This patch add EMAC driver support for H3/A83T/A64 SoCs.
Tested on Pine64(A64-External PHY) and Orangepipc(H3-Internal PHY).
BIG Thanks to Andre for providing some of the DT code.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
sunxi: mmc: increase status register polling rate for data transfers
With a recent bunch of SD3.0 cards in our A20-based board we
experienced data transfer rates of about 250 KiB/s instead of 10 MiB/s
with previous cards from the same vendor (both 4 GB/class 10). By
increasing status register polling rate from 1 kHz to 1 MHz we were
able to reach the original transfer rates again. With the old cards
we now even reach about 16 MiB/s.
Signed-off-by: Tobias Doerffel <tobias.doerffel@ed-chemnitz.de> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
sunxi: FEL - Add the ability to recognize and auto-import uEnv-style data
The patch converts one of the "reserved" fields in the sunxi SPL
header to a fel_uEnv_length entry. When booting over USB ("FEL
mode"), this enables the sunxi-fel utility to pass the string
length of uEnv.txt compatible data; at the same time requesting
that this data be imported into the U-Boot environment.
If parse_spl_header() in the sunxi board.c encounters a non-zero
value in this header field, it will therefore call himport_r() to
merge the string (lines) passed via FEL into the default settings.
Environment vars can be changed this way even before U-Boot will
attempt to autoboot - specifically, this also allows overriding
"bootcmd".
With fel_script_addr set and a zero fel_uEnv_length, U-Boot is
safe to assume that data in .scr format (a mkimage-type script)
was passed at fel_script_addr, and will handle it using the
existing mechanism ("bootcmd_fel").
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de> Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Allwinner devices support SPI flash as one of the possible
bootable media type. The SPI flash chip needs to be connected
to SPI0 pins (port C) to make this work. More information is
available at:
https://linux-sunxi.org/Bootable_SPI_flash
This patch adds the initial support for booting from SPI flash.
The existing SPI frameworks are not used in order to reduce the
SPL code size. Right now the SPL size grows by ~370 bytes when
CONFIG_SPL_SPI_SUNXI option is enabled.
While there are no popular Allwinner devices with SPI flash at
the moment, testing can be done using a SPI flash module (it
can be bought for ~2$ on ebay) and jumper wires with the boards,
which expose relevant pins on the expansion header. The SPI flash
chips themselves are very cheap (some prices are even listed as
low as 4 cents) and should not cost much if somebody decides to
design a development board with an SPI flash chip soldered on
the PCB.
Another nice feature of the SPI flash is that it can be safely
accessed in a device-independent way (since we know that the
boot ROM is already probing these pins during the boot time).
And if, for example, Olimex boards opted to use SPI flash instead
of EEPROM, then they would have been able to have U-Boot installed
in the SPI flash now and boot the rest of the system from the SATA
hard drive. Hopefully we may see new interesting Allwinner based
development boards in the future, now that the software support
for the SPI flash is in a better shape :-)
Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option
in a board defconfig, then building U-Boot and finally flashing
the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with
a help of the sunxi-fel tool:
The device needs to be switched into FEL (USB recovery) mode first.
The most suitable boards for testing are Orange Pi PC and Pine64.
Because these boards are cheap, have no built-in NAND/eMMC and
expose SPI0 pins on the Raspberry Pi compatible expansion header.
The A13-OLinuXino-Micro board also can be used.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Simon Glass [Mon, 4 Jul 2016 17:58:41 +0000 (11:58 -0600)]
dm: Add a test for of-platdata
Add a simple test which checks that the of-platdata system is working
correctly. The sequence is as follows:
- SPL starts up and probes all the UCLASS_MISC drivers
- There are 3 of these in sandbox.dts
- Therefore there should be 3 U_BOOT_DEVICE() declarations in dt-platdata.c
- These should produce 3 sandbox_spl_test devices
- Each device prints out its platform data when probed
- This test checks for this output and compares it against expectations
Simon Glass [Mon, 4 Jul 2016 17:58:38 +0000 (11:58 -0600)]
test/py: Note which console produced unexpected output
At present the SPL and U-Boot consoles both present the same error message
when the expected console output does not appear. Add "SPL" to the SPL error
message to resolve this ambiguity.
Simon Glass [Mon, 4 Jul 2016 17:58:36 +0000 (11:58 -0600)]
rockchip: Use of-platdata for firefly-rk3288
As an experiment, move this board over to use of-platdata. This means that
its SPL configuration will come from C structures generated at build-time
from the device tree, instead of coming from the device tree at run-time.
Simon Glass [Mon, 4 Jul 2016 17:58:35 +0000 (11:58 -0600)]
rockchip: sdram: Update the driver to support of-platdata
Add support for of-platdata with rk3288 SDRAM initr. This requires decoding
the of-platdata struct and setting up the device from that. Also the driver
needs to be renamed to match the string that of-platdata will search for.
The platform data is copied from the of-platdata structure to the one used
by the driver. This allows the same code to be used with device tree and
of-platdata.
Simon Glass [Mon, 4 Jul 2016 17:58:34 +0000 (11:58 -0600)]
rockchip: sdram: Move all DT decoding to ofdata_to_platdata()
It is more correct to avoid touching the device tree in the probe() method.
Update the driver to work this way. Note that only SPL needs to fiddle with
the SDRAM registers, so decoding the platform data fully is not necessary in
U-Boot proper.
Simon Glass [Mon, 4 Jul 2016 17:58:33 +0000 (11:58 -0600)]
rockchip: syscon: Update to work with of-platdata
The syscon devices all end up having diffent driver names with of-platdata,
since the driver name comes from the first string in the compatible list.
Add separate device declarations for each one, and add a bind method to set
up driver_data correctly.
projects / u-boot / log